Commit Graph

91 Commits

Author SHA1 Message Date
Baruch Siach 85b7d8abfe gpio: mvebu: add pwm support for Armada 8K/7K
Use the marvell,pwm-offset DT property to store the location of PWM
signal duration registers.

Since we have more than two GPIO chips per system, we can't use the
alias id to differentiate between them. Use the offset value for that.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15 11:43:31 +01:00
Baruch Siach 0b68d02b6a gpio: mvebu: improve handling of pwm zero on/off values
Hardware appears to treat zero value as 2^32. Take advantage of this
fact to support on/off values of up to UINT_MAX+1 == 2^32. Adjust both
.apply and .get_state to handle zero as a special case.

Rounded up division result in .get_state can't be zero, since the
dividend is now larger than 0. Remove check for this case.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Analyzed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15 11:43:30 +01:00
Baruch Siach 2bee255a5e gpio: mvebu: don't limit pwm period/duty_cycle to UINT_MAX
PWM on/off registers are limited to UINT_MAX. However the state period
and duty_cycle fields are ns values of type u64. There is no reason to
limit them to UINT_MAX.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15 11:43:30 +01:00
Baruch Siach de1eaf6016 gpio: mvebu: make pwm .get_state closer to idempotent
Round up the divisions in .get_state() to make applying the read out
configuration idempotent in most cases as .apply rounds down.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15 11:43:30 +01:00
Baruch Siach aa37e27f61 gpio: mvebu: improve pwm period calculation accuracy
Change 'off' register value calculation from

  $off = (period - duty_cycle) * clkrate / NSEC_PER_SEC

to

  $off = (period * clkrate / NSEC_PER_SEC) - $on

That is, divide the full period value to reduce rounding error.

Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15 11:43:30 +01:00
Baruch Siach e73b0101ae gpio: mvebu: fix pwm .get_state period calculation
The period is the sum of on and off values. That is, calculate period as

  ($on + $off) / clkrate

instead of

  $off / clkrate - $on / clkrate

that makes no sense.

Reported-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-01-19 11:58:22 +01:00
Linus Torvalds a409ed156a This is the bulk of the GPIO changes for the v5.11 kernel cycle:
Core changes:
 
 - Retired the old set-up function for GPIO IRQ chips. All chips
   now use the template struct gpio_irq_chip and pass that to the core
   to be set up alongside the gpio_chip. We can finally get rid of
   the old cruft.
 
 - Some refactoring and clean up of the core code.
 
 - Support edge event timestamps to be stamped using REALTIME
   (wall clock) timestamps. We have found solid use cases for
   this, so we support it.
 
 New drivers:
 
 - MStar MSC313 GPIO driver.
 
 - HiSilicon GPIO driver.
 
 Driver improvements:
 
 - The PCA953x driver now also supports the NXP PCAL9554B/C chips.
 
 - The mockup driver can now be probed from the device tree which
   is pretty useful for virtual prototyping of devices.
 
 - The Rcar driver now supports .get_multiple()
 
 - The MXC driver dropped some legacy and became a pure device
   tree client.
 
 - The Exar driver was moved over to the IDA interface for
   enumerating, and also switched over to using regmap for
   register access.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl/b0r0ACgkQQRCzN7AZ
 XXPRIQ/+P2VxypIIi8o5ZJLt/UN1CPGbh10WCl9yR95pM7Ekxocsa05MMAyPCbCA
 SzDSo4wfrbVLd+C8oqGyLcyxR4A8LQDoc/MaBUC60SDr/BY2eu6bRCs9UttWUPUN
 59H0r/dMAcSpIXwB9A7dKmF7Ps1Lz9naeZiGV8vw8hmuN4h3RtsWd10h8WDhByoq
 RA099lNKs6pFpx61hvn+6mr8ewkm6RFh9q9/eg+zU0gVeaXpYLO6zHTnRS3dARIg
 9qLZ54mRUAeybpUCi+CpleUM7qQI8wYHB7pJutAXByWVACie91P5youJv2JvMgs3
 rvYyjRkHkM+EtpyXStv5zzfIi0JF746zWeeQmrR3bYy7prnIjjkUgIZb2Jmqu0p2
 R0PAOmylociuSsEpARIqlGebqMKlmpsekuhJsf8x53le3nM4B2qC6fVEXFfYrp2L
 sTfxeejmIFBBLLSSbfBFQOk3La9YBURGsidqgA2lQXL1ZSVhV6UrfblyLET6cOgs
 y4ORYCV4SxeErUhePkA0GXjnu00nC9iD2Too6sTF+oRIirXX3R4SBbgoHKBEhMNe
 /CWjYduwg7SkqwdeaBpZNU9jpFqq8Rny6nid13FMFORJWAszECzxcBIUaN55S/98
 Z8QD0DJNo9nJZdtwT7OYE+x7/QcxgIHClU5MsrXS4yf3SlZHbAk=
 =nrFU
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of the GPIO changes for the v5.11 kernel cycle:

  Core changes:

   - Retired the old set-up function for GPIO IRQ chips. All chips now
     use the template struct gpio_irq_chip and pass that to the core to
     be set up alongside the gpio_chip. We can finally get rid of the
     old cruft.

   - Some refactoring and clean up of the core code.

   - Support edge event timestamps to be stamped using REALTIME (wall
     clock) timestamps. We have found solid use cases for this, so we
     support it.

  New drivers:

   - MStar MSC313 GPIO driver.

   - HiSilicon GPIO driver.

  Driver improvements:

   - The PCA953x driver now also supports the NXP PCAL9554B/C chips.

   - The mockup driver can now be probed from the device tree which is
     pretty useful for virtual prototyping of devices.

   - The Rcar driver now supports .get_multiple()

   - The MXC driver dropped some legacy and became a pure device tree
     client.

   - The Exar driver was moved over to the IDA interface for
     enumerating, and also switched over to using regmap for register
     access"

* tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
  MAINTAINERS: Remove reference to non-existing file
  gpio: hisi: Do not require ACPI for COMPILE_TEST
  MAINTAINERS: Add maintainer for HiSilicon GPIO driver
  gpio: gpio-hisi: Add HiSilicon GPIO support
  gpio: cs5535: Simplify the return expression of cs5535_gpio_probe()
  gpiolib: irq hooks: fix recursion in gpiochip_irq_unmask
  dt-bindings: mt7621-gpio: convert bindings to YAML format
  gpiolib: cdev: Flag invalid GPIOs as used
  gpio: put virtual gpio device into their own submenu
  drivers: gpio: amd8111: use SPDX-License-Identifier
  drivers: gpio: amd8111: prefer dev_err()/dev_info() over raw printk
  drivers: gpio: bt8xx: prefer dev_err()/dev_warn() over of raw printk
  gpio: Add TODO item for debugfs interface
  gpio: just plain warning when nonexisting gpio requested
  tools: gpio: add option to report wall-clock time to gpio-event-mon
  tools: gpio: add support for reporting realtime event clock to lsgpio
  gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
  gpio: msc313: MStar MSC313 GPIO driver
  dt-bindings: gpio: Binding for MStar MSC313 GPIO controller
  dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
  ...
2020-12-17 18:07:20 -08:00
Baruch Siach 48f32a8353 gpio: mvebu: switch pwm duration registers to regmap
Commit 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
changed most readl/writel registers access calls to the regmap API in
preparation for Armada 7K/8K support. PWM duration registers were left using
readl/writel, as the driver does not support PWM for Armada 7K/8K.

Switch PWM duration registers to regmap as first step in adding Armada 7K/8K
PWM functionality support.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-12-02 12:08:21 +01:00
Baruch Siach 64b19f6abe gpio: mvebu: update Armada XP per-CPU comment
Commit 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
introduced percpu_regs to replace percpu_membase. Update the comment to
match.

Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes: 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-12-02 12:08:13 +01:00
Baruch Siach 7ee1a01e47 gpio: mvebu: fix potential user-after-free on probe
When mvebu_pwm_probe() fails IRQ domain is not released. Move pwm probe
before IRQ domain allocation. Add pwm cleanup code to the failure path.

Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-12-02 12:01:51 +01:00
Andy Shevchenko 86661fd7fa gpio: mvebu: Make use of for_each_requested_gpio()
Make use of for_each_requested_gpio() instead of home grown analogue.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200615150545.87964-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-06-20 23:13:27 +02:00
Sascha Hauer 19c26d90ff gpio: mvebu: Fix probing for chips without PWM
The PWM iomem resource is optional and its presence indicates whether
the GPIO chip has a PWM or not, which is why mvebu_pwm_probe() returned
successfully when the PWM resource was not present. With f51b18d92b
the driver switched to devm_platform_ioremap_resource_byname() and
its error return is propagated to the caller, so now a missing PWM resource
leads to a probe error in the driver.

To fix this explicitly test for the presence of the PWM resource and
return successfully when it's not there. Do this check before the check
for the clock is done (which GPIO chips without a PWM do not have). Also
move the existing comment why the PWM resource is optional up to the
actual check.

Fixes: f51b18d92b ("gpio: mvebu: use devm_platform_ioremap_resource_byname()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-04-24 08:31:50 +02:00
Chris Packham 525b0858ff gpio: mvebu: avoid error message for optional IRQ
platform_get_irq() will generate an error message if the requested irq
is not present

  mvebu-gpio f1010140.gpio: IRQ index 3 not found

use platform_get_irq_optional() to avoid the error message being
generated.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-03-25 09:50:45 +01:00
Maxim Kiselev d5331ec2cc gpio: mvebu: clear irq in edge cause register before unmask edge irq
When input GPIO set from 0 to 1, the interrupt bit asserted in the GPIO
Interrupt Cause Register (ICR) even if the corresponding interrupt
masked in the GPIO Interrupt Mask Register.

Because interrupt mask register only affects assertion of the interrupt
bits in Main Interrupt Cause Register and it does not affect the
setting of bits in the GPIO ICR.

So, there is problem, when we unmask interrupt with already
asserted bit in the GPIO ICR, then false interrupt immediately occurs
even if GPIO don't change their value since last unmask.

Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20200115073811.24438-1-bigunclemax@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-23 15:52:40 +01:00
Peng Fan 0c21639f5a gpio: mvebu: use platform_irq_count
platform_irq_count() is the more generic way (independent of
device trees) to determine the count of available interrupts. So
use this instead.

As platform_irq_count() might return an error code (which
of_irq_count doesn't) some additional handling is necessary.

Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-11 11:06:06 +01:00
Bartosz Golaszewski a6e191963f Merge remote-tracking branch 'driver-core/driver-core-next' into gpio/for-next 2019-11-12 16:30:17 +01:00
Matti Vaittinen e42615ec23 gpio: Use new GPIO_LINE_DIRECTION
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.

NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-07 09:27:48 +01:00
Bartosz Golaszewski f51b18d92b gpio: mvebu: use devm_platform_ioremap_resource_byname()
Use devm_platform_ioremap_resource_byname() instead of calling
platform_get_resource_byname() and devm_ioremap_resource() separately.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191022084318.22256-8-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05 18:33:13 +01:00
Uwe Kleine-König 71523d1812 pwm: Ensure pwm_apply_state() doesn't modify the state argument
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:

        #define PERIOD 5000000
        #define DUTY_LITTLE 10
        ...
        struct pwm_state state = {
                .period = PERIOD,
                .duty_cycle = DUTY_LITTLE,
                .polarity = PWM_POLARITY_NORMAL,
                .enabled = true,
        };

        pwm_apply_state(mypwm, &state);
        ...
        state.duty_cycle = PERIOD / 2;
        pwm_apply_state(mypwm, &state);

For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.

So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2019-09-21 03:25:10 +02:00
Linus Walleij 5923ea6c2c gpio: pass lookup and descriptor flags to request_own
When a gpio_chip wants to request a descriptor from itself
using gpiochip_request_own_desc() it needs to be able to specify
fully how to use the descriptor, notably line inversion
semantics. The workaround in the gpiolib.c can be removed
and cases (such as SPI CS) where we need at times to request
a GPIO with line inversion semantics directly on a chip for
workarounds, can be fully supported with this call.

Fix up some users of the API that weren't really using the
last flag to set up the line as input or output properly
but instead just calling direction setting explicitly
after requesting the line.

Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-06-07 23:20:23 +02:00
Enrico Weigelt, metux IT consult dc02a0cacb drivers: gpio: mvebu: use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.

Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-05 00:04:27 +07:00
Baruch Siach e8dacf5957 gpio: mvebu: implement get_direction
struct gpio_chip documentation recommends to always implement this
callback function.

A more concrete motivation is to be able (in combination with
GPIOD_ASIS) to detect whether the bootloader has changed the state of a
GPIO signal.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-10 16:19:11 +01:00
Linus Torvalds 24dc83635f This is the bulk of GPIO changes for the v4.21 kernel series:
Core changes:
 
 - Some core changes are already in outside of this pull
   request as they came through the regulator tree, most
   notably devm_gpiod_unhinge() that removes devres refcount
   management from a GPIO descriptor. This is needed in
   subsystems such as regulators where the regulator core
   need to take over the reference counting and lifecycle
   management for a GPIO descriptor.
 
 - We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
   as nothing needs it. We can bring it back if need be.
 
 - Add a global TODO so people see where we are going. This
   helps setting the direction now that we are two GPIO
   maintainers.
 
 - Handle the MMC CD/WP properties in the device tree core.
   (The bulk of patches activating this code is already
   merged through the MMC/SD tree.)
 
 - Augment gpiochip_request_own_desc() to pass a flag so
   we as gpiochips can request lines as active low or open
   drain etc even from ourselves.
 
 New drivers:
 
 - New driver for Cadence GPIO blocks.
 
 - New driver for Atmel SAMA5D2 PIOBU GPIO lines.
 
 Driver improvements:
 
 - A major refactoring of the PCA953x driver - this driver has
   been around for ages, and is now modernized to reduce code
   duplication that has stacked up and is using regmap to read
   write and cache registers.
 
 - Intel drivers are now maintained in a separate tree and
   start with a round of cleanups and unifications.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJcJJcmAAoJEEEQszewGV1zdCoQAMSLPh+4QdYLFS3ZmnsPvZkg
 Zkz94RVT+uLLmHpR8XBl0wl4mmYCiwB50IwsXwlvJGceSXjCn6hLg9BZBP5hFMCb
 yFk3fgXQSh7TOnpjgbCWSssCjpejQ0cOb/2nWHz5s/fbYKYlh3VXckW9hhW+R+b3
 6+Mno1SzmBkpVVQ21ISlZeLoNDynkCW6DfjiKMuHAyxzxa0oZ9Qid+tnVDnQM4rD
 rCnvYLuvxlXw97W+LI7AU9KoCITdO+2M/0dtGVEEYKfHseRReSy2Oo3nlqCglygX
 cNkBe9RYU1CJdas1P/c18wjDAqWp/pbugzHDkYF5Y3tBtB2rQSftjtnQngiVMXMt
 De7ejPvL7/OLECvI2WUD6y9NAduw/HE4FO8BBdn0gP/a9svJpVZ993yPd3F9n7EZ
 ZIBpycDZVtkcE7dwQgek17bFILRY5nBBMB9oCLL2wk48qdmjpcAbxVfGSsYOe6wO
 +cZRZuj/eR3i9gHRugfFx7Evoc7l4erihTpES/YAy3De1s3uV8KjT4zE7Jh+M9LW
 GM797BcXJJeb5toC7HZ/G2UAVMyWEhY0n7PGG616CS8IrzmzIZpJOL9kUVOWPb0F
 9CPt6qhVbUl9rxp1H/Z3TxvYqIw6icn/z5YewZxLU1zaBlpE3jc7PhZb5hOGnFUf
 /DWwe4n99JsjHTrGx1ra
 =05LW
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.21 kernel series.

  Core changes:

   - Some core changes are already in outside of this pull request as
     they came through the regulator tree, most notably
     devm_gpiod_unhinge() that removes devres refcount management from a
     GPIO descriptor. This is needed in subsystems such as regulators
     where the regulator core need to take over the reference counting
     and lifecycle management for a GPIO descriptor.

   - We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
     nothing needs it. We can bring it back if need be.

   - Add a global TODO so people see where we are going. This helps
     setting the direction now that we are two GPIO maintainers.

   - Handle the MMC CD/WP properties in the device tree core. (The bulk
     of patches activating this code is already merged through the
     MMC/SD tree.)

   - Augment gpiochip_request_own_desc() to pass a flag so we as
     gpiochips can request lines as active low or open drain etc even
     from ourselves.

  New drivers:

   - New driver for Cadence GPIO blocks.

   - New driver for Atmel SAMA5D2 PIOBU GPIO lines.

  Driver improvements:

   - A major refactoring of the PCA953x driver - this driver has been
     around for ages, and is now modernized to reduce code duplication
     that has stacked up and is using regmap to read write and cache
     registers.

   - Intel drivers are now maintained in a separate tree and start with
     a round of cleanups and unifications"

* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
  gpio: sama5d2-piobu: Depend on OF_GPIO
  gpio: Add Cadence GPIO driver
  dt-bindings: gpio: Add bindings for Cadence GPIO
  gpiolib-acpi: remove unused variable 'err', cleans up build warning
  gpio: mxs: read pin level directly instead of using .get
  gpio: aspeed: remove duplicated statement
  gpio: add driver for SAMA5D2 PIOBU pins
  dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
  gpio/mmc/of: Respect polarity in the device tree
  dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
  memory: omap-gpmc: Get the header of the enum
  ARM: omap1: Fix new user of gpiochip_request_own_desc()
  gpio: pca953x: Add regmap dependency for PCA953x driver
  gpio: raspberrypi-exp: decrease refcount on firmware dt node
  gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
  gpio: pca953x: Restore registers after suspend/resume cycle
  gpio: pca953x: Zap single use of pca953x_read_single()
  gpio: pca953x: Zap ad-hoc reg_output cache
  gpio: pca953x: Zap ad-hoc reg_direction cache
  gpio: pca953x: Perform basic regmap conversion
  ...
2018-12-28 20:00:21 -08:00
Uwe Kleine-König c8da642d41 gpio: mvebu: only fail on missing clk if pwm is actually to be used
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.

Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-21 09:23:46 +01:00
Linus Walleij 21abf10381 gpio: Pass a flag to gpiochip_request_own_desc()
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.

Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-14 14:24:33 +01:00
Linus Walleij ba78d83be7 gpio: mvebu: Use the proper APIs
The MVEBU driver is requesting GPIO descriptors from itself, which
is fine, but we have proper APIs to do this in a controlled way, so
stop calling into the private functions of the GPIO library and use
the gpiochip_* functions instead. Only include <linux/gpio/driver.h>
and <linux/gpio/consumer.h> since we are both producers and consumers
in this case.

Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-16 14:35:24 +02:00
Gregory CLEMENT 3f13b6a24f gpio: mvebu: Fix cause computation in irq handler
When switching to regmap, the way to compute the irq cause was
reorganized. However while doing it, a typo was introduced: a 'xor'
replaced a 'and'.

This lead to wrong behavior in the interrupt handler ans one of the
symptom was wrong irq handler called on the Armada 388 GP:
"->handle_irq():  c016303c,
handle_bad_irq+0x0/0x278
->irq_data.chip(): c0b0ec0c,
0xc0b0ec0c
->action():   (null)
   IRQ_NOPROBE set
 IRQ_NOREQUEST set
unexpected IRQ trap at vector 00
irq 0, desc: ee804800, depth: 1, count: 0, unhandled: 0"

Fixes: 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:00:43 +02:00
Linus Torvalds c7d28eca1d This is the bulk of GPIO changes for the v4.13 series:
Core:
 - Export add/remove for lookup tables so that modules can export GPIO
   descriptor tables.
 - Handle GPIO sleep states: it is now possible to flag that a GPIO line
   may loose its state during suspend/resume of the system to save
   power. This is used in the Wolfson Micro Arizona driver.
 - ACPI-based GPIO was tightened up a lot around the edges.
 - Use bitmap_fill() to speed up a loop.
 
 New drivers:
 - Exar XRA1403 SPI-based GPIO.
 - MVEBU driver now supports Armada 7K and 8K.
 - LP87565 PMIC GPIO.
 - Renesas R-CAR R8A7743 (RZ/G1M).
 - The new IOT2040 8250 serial/GPIO also comes in through this
   changeset.
 
 Substantial driver changes:
 - Seriously fix the Exar 8250 GPIO portions to work.
 - The MCP23S08 was moved out to a pin control driver.
 - Convert MEVEBU to use regmap for register access.
 - Drop Vulcan support from the Broadcom driver.
 - Serious cleanup and improvement of the mockup driver, giving us a
   better test coverage.
 
 Misc:
 - Lots of janitorial clean up.
 - A bunch of documentation fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJZX1MjAAoJEEEQszewGV1zEYUQALFsjJH7D2mRN4TSSEeVAcYr
 Uz52uupsou8tgW0IupRb/khO+V6zgd7j+kHDJLMxX+rCTw3pTq5+XGyi5+iNpxof
 TIIT1XBx4eq7Q/n4nWdGodHbHN9BXw7cGsNmTb1TS/G/6h1wOKxfzjvUNhDAC+2v
 idPy6B5G+WrDsYpBtTWlKHKQKVqbUlhLFyJYoglzqIeM5L9Ry/UoZ6sGleho3hKn
 Vlg/hMtkCexnVO9zopBe5CuEfseLrkcCgCvtQ713egzVXApryp4hqm3Xti20Ntgy
 OxnKhmVyloqd0kU0qLSpvDAf7B1invbHHbeZsag6wluTMrxgUYJONuonrqGeGiwB
 FBDtw9SGn2GlEXcs7sg8ANmAyr2XxxezKXD9XLBL5jadNB2KCY5yKMv1IK3VnYdq
 gEpFAiZ5cmlpZxIXqlyeZP6LKHNTci4amb33x1I/ghH2BTkGQ/3E3anXEbPNWF8G
 DDE6nrSgU0oQcNqRHyZaWNZpUIz4aFUgJtOEO4lYYP4+VzYSKTdrHseTiiJ91J7E
 WBz9p5JvSnB22+60RhyTAPjVjXgWa30nidf7WGCK0UHiIYffihCxGZRTlrhoEEUB
 fXgveJpqxLopYvxpUxi1OqlPYYo7zKRF5BzHsjKMpdVYXfdMdvs7eq2g/X889i1D
 WpbE9LyAH9FY5BM8YjFX
 =TpW1
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.13 series.

  Some administrativa:

  I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
  driver coming in through this tree, along with a whole bunch of Exar
  8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
  where they are ACKed by Andy Shevchenko.

  Speaking about drivers/platform/* there is also a bunch of ACPI stuff
  coming through that route, again ACKed by Andy.

  The MCP23S08 changes are coming in here as well. You already have the
  commits in your tree, so this is just a result of sharing an immutable
  branch between pin control and GPIO.

  Core:
   - Export add/remove for lookup tables so that modules can export GPIO
     descriptor tables.
   - Handle GPIO sleep states: it is now possible to flag that a GPIO
     line may loose its state during suspend/resume of the system to
     save power. This is used in the Wolfson Micro Arizona driver.
   - ACPI-based GPIO was tightened up a lot around the edges.
   - Use bitmap_fill() to speed up a loop.

  New drivers:
   - Exar XRA1403 SPI-based GPIO.
   - MVEBU driver now supports Armada 7K and 8K.
   - LP87565 PMIC GPIO.
   - Renesas R-CAR R8A7743 (RZ/G1M).
   - The new IOT2040 8250 serial/GPIO also comes in through this
     changeset.

  Substantial driver changes:
   - Seriously fix the Exar 8250 GPIO portions to work.
   - The MCP23S08 was moved out to a pin control driver.
   - Convert MEVEBU to use regmap for register access.
   - Drop Vulcan support from the Broadcom driver.
   - Serious cleanup and improvement of the mockup driver, giving us a
     better test coverage.

  Misc:
   - Lots of janitorial clean up.
   - A bunch of documentation fixes"

* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
  serial: exar: Add support for IOT2040 device
  gpio-exar/8250-exar: Make set of exported GPIOs configurable
  platform: Accept const properties
  serial: exar: Factor out platform hooks
  gpio-exar/8250-exar: Rearrange gpiochip parenthood
  gpio: exar: Fix iomap request
  gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
  serial: uapi: Add support for bus termination
  gpio: rcar: Add R8A7743 (RZ/G1M) support
  gpio: gpio-wcove: Fix GPIO control register offset calculation
  gpio: lp87565: Add support for GPIO
  gpio: dwapb: fix missing first irq for edgeboth irq type
  MAINTAINERS: Take maintainership for GPIO ACPI support
  gpio: exar: Fix reading of directions and values
  gpio: exar: Allocate resources on behalf of the platform device
  gpio-exar/8250-exar: Fix passing in of parent PCI device
  gpio: mockup: use devm_kcalloc() where applicable
  gpio: mockup: add myself as author
  gpio: mockup: improve the error message
  gpio: mockup: don't return magic numbers from probe()
  ...
2017-07-07 12:40:27 -07:00
Ralph Sennhauser 6c7515c61f gpio: mvebu: change compatible string for PWM support
As it turns out more than just Armada 370 and XP support using GPIO
lines as PWM lines. For example the Armada 38x family has the same
hardware support. As such "marvell,armada-370-xp-gpio" for the
compatible string is a misnomer.

Change the compatible string to "marvell,armada-370-gpio" before the
driver makes it out of the -rc stage. This also follows the practice of
using only the first device family supported as part of the name.

Also update the documentation and comments in the code accordingly.

Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-20 13:42:20 +02:00
Gregory CLEMENT b6730b2083 gpio: mvebu: Add support for the Armada 7K/8K SoCs
The Armada 7K and 8K SoCs use the same gpio controller as most of the
other mvebu SoCs. However, the main difference is that the GPIO
controller is part of a bigger system controller, and a syscon is used to
control the overall system controller. Therefore, the driver needs to be
adjusted to retrieve the regmap of the syscon to access registers, and
account for the fact that registers are located at a certain offset
within the regmap.

This commit add the support of the syscon and introduce a new variant for
this case.

It was based on the preliminary work of Thomas Petazzoni.

Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-16 11:28:29 +02:00
Gregory CLEMENT 43a2dcecd8 gpio: mvebu: fix regmap_update_bits usage
In some place in the driver regmap_update_bits was misused. Indeed the
last argument is not the value of the bit (or group of bits) itself but
the mask value inside the register.

So when setting the bit N, then the value must be BIT(N) and not 1.

CC: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-16 11:15:20 +02:00
Richard Genoud fc7a906867 gpio: mvebu: fix gpio bank registration when pwm is used
If more than one gpio bank has the "pwm" property, only one will be
registered successfully, all the others will fail with:
mvebu-gpio: probe of f1018140.gpio failed with error -17

That's because in alloc_pwms(), the chip->base (aka "int pwm"), was not
set (thus, ==0) ; and 0 is a meaningful start value in alloc_pwm().
What was intended is mvpwm->chip->base = -1.
Like that, the numbering will be done auto-magically

Moreover, as the region might be already occupied by another pwm, we
shouldn't force:
mvpwm->chip->base = 0
nor
mvpwm->chip->base = id * MVEBU_MAX_GPIO_PER_BANK;

Tested on clearfog-pro (Marvell 88F6828)

Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-09 09:38:27 +02:00
Richard Genoud c528eb27a3 gpio: mvebu: fix blink counter register selection
The blink counter A was always selected because 0 was forced in the
blink select counter register.
The variable 'set' was obviously there to be used as the register value,
selecting the B counter when id==1 and A counter when id==0.

Tested on clearfog-pro (Marvell 88F6828)

Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-09 09:36:59 +02:00
Thomas Petazzoni 2233bf7a92 gpio: mvebu: switch to regmap for register access
In order to be able to use this driver with the Armada 7K/8K SoCs, we
need to use the regmap to access the registers. Indeed for these new SoCs,
the gpio node will be part of a syscon.

[gregory.clement@free-electrons.com:
 - fixed merge conflcit from 4.10 to 4.12-rc1
 - added a commit log]

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23 11:16:02 +02:00
Gregory CLEMENT 6ec015d613 gpio: mvebu: sort header include
This commit sorts alphabetically the header files.

Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-23 11:14:59 +02:00
Andrew Lunn 757642f9a5 gpio: mvebu: Add limited PWM support
Armada 370/XP devices can 'blink' GPIO lines with a configurable on
and off period. This can be modelled as a PWM.

However, there are only two sets of PWM configuration registers for
all the GPIO lines. This driver simply allows a single GPIO line per
GPIO chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.

Due to the interleaving of registers it is not simple to separate the
PWM driver from the GPIO driver. Thus the GPIO driver has been
extended with a PWM driver.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
  * Port forward
  * Merge PWM portion into gpio-mvebu.c
  * Switch to atomic PWM API
  * Add new compatible string marvell,armada-370-xp-gpio
  * Update and merge documentation patch
  * Update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-04-24 11:16:25 +02:00
Ralph Sennhauser d2cabc4a23 gpio: mvebu: use BIT macro instead of bit shifting
Use the BIT macro instead of explicitly shifting bits for some added
clarity.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-23 10:21:39 +01:00
Ralph Sennhauser f07708c43b gpio: mvebu: let the compiler inline
A modern compiler should know better when to inline, so drop the inline
keywords.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:16 +01:00
Ralph Sennhauser f4c240ca4b gpio: mvebu: extra whitespace fixes
Fix whitespace errors missed by checkpatch.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:15 +01:00
Ralph Sennhauser 163ad364cc gpio: mvebu: checkpatch: whitespace fixes
Fix whitespace errors reported by checkpatch.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:15 +01:00
Ralph Sennhauser d276de70d2 gpio: mvebu: checkpatch: unsigned int fixes
Use unsigned int instead of plain unsigned as reported by checkpatch.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:14 +01:00
Ralph Sennhauser 899c37edfe gpio: mvebu: start multiline block comments with blank line
While this isn't an issue according to checkpatch two styles are used.
Add a blank line to the block comments missing a blank line at the start
so multiline block comments look the same across the file.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:14 +01:00
Ralph Sennhauser 7077f4cc1e gpio: mvebu: checkpatch: block comment fixes
Fix issues in block comments reported by checkpatch.

Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16 21:52:13 +01:00
Russell King f0d5046075 gpio: mvebu: fix warning when building on 64-bit
Casting a pointer to an int is not portable, and provokes a compiler
warning.  Cast to unsigned long instead to avoid the warning.

drivers/gpio/gpio-mvebu.c: In function 'mvebu_gpio_probe':
drivers/gpio/gpio-mvebu.c:662:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
   soc_variant = (int) match->data;
                 ^

This will be needed when building gpio-mvebu for Armada 7k/8k ARM64
SoCs.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-11 16:47:04 +01:00
Jason Gunthorpe 812d47889a gpio/mvebu: Use irq_domain_add_linear
This fixes the irq allocation in this driver to not print:
 irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
 irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated

Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.

Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy

Fixes: ce931f571b ("gpio/mvebu: convert to use irq_domain_add_simple()")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-01 19:31:49 +01:00
Paul Gortmaker ed329f3a64 gpio: mvebu: make explicitly non-modular
The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MVEBU
drivers/gpio/Kconfig:   def_bool y

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-31 15:05:44 +02:00
Laxman Dewangan 00b9ab4a25 gpio: mvebu: Use devm_gpiochip_add_data() for gpio registration
Use devm_gpiochip_add_data() for GPIO registration and clean the
error path.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
2016-02-23 20:35:37 +05:30
Linus Walleij bbe760041a gpio: mvebu: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05 11:21:09 +01:00
Linus Walleij 58383c7842 gpio: change member .dev to .parent
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19 09:24:35 +01:00
Jonas Gorski 203f0daafd gpio: replace trivial implementations of request/free with generic one
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-16 22:13:43 +02:00