Add base code for supporting the MIPS SIMD Architecture (MSA) in MIPS
KVM guests. MSA cannot yet be enabled in the guest, we're just laying
the groundwork.
As with the FPU, whether the guest's MSA context is loaded is stored in
another bit in the fpu_inuse vcpu member. This allows MSA to be disabled
when the guest disables it, but keeping the MSA context loaded so it
doesn't have to be reloaded if the guest re-enables it.
New assembly code is added for saving and restoring the MSA context,
restoring only the upper half of the MSA context (for if the FPU context
is already loaded) and for saving/clearing and restoring MSACSR (which
can itself cause an MSA FP exception depending on the value). The MSACSR
is restored before returning to the guest if MSA is already enabled, and
the existing FP exception die notifier is extended to catch the possible
MSA FP exception and step over the ctcmsa instruction.
The helper function kvm_own_msa() is added to enable MSA and restore
the MSA context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use MSA for the first time and
triggers an MSA disabled exception.
The existing FPU helpers are extended to handle MSA. kvm_lose_fpu()
saves the full MSA context if it is loaded (which includes the FPU
context) and both kvm_lose_fpu() and kvm_drop_fpu() disable MSA.
kvm_own_fpu() also needs to lose any MSA context if FR=0, since there
would be a risk of getting reserved instruction exceptions if CU1 is
enabled and we later try and save the MSA context. We shouldn't usually
hit this case since it will be handled when emulating CU1 changes,
however there's nothing to stop the guest modifying the Status register
directly via the comm page, which will cause this case to get hit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add base code for supporting FPU in MIPS KVM guests. The FPU cannot yet
be enabled in the guest, we're just laying the groundwork.
Whether the guest's FPU context is loaded is stored in a bit in the
fpu_inuse vcpu member. This allows the FPU to be disabled when the guest
disables it, but keeping the FPU context loaded so it doesn't have to be
reloaded if the guest re-enables it.
An fpu_enabled vcpu member stores whether userland has enabled the FPU
capability (which will be wired up in a later patch).
New assembly code is added for saving and restoring the FPU context, and
for saving/clearing and restoring FCSR (which can itself cause an FP
exception depending on the value). The FCSR is restored before returning
to the guest if the FPU is already enabled, and a die notifier is
registered to catch the possible FP exception and step over the ctc1
instruction.
The helper function kvm_lose_fpu() is added to save FPU context and
disable the FPU, which is used when saving hardware state before a
context switch or KVM exit (the vcpu_get_regs() callback).
The helper function kvm_own_fpu() is added to enable the FPU and restore
the FPU context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use the FPU for the first time
and triggers a co-processor unusable exception.
The helper function kvm_drop_fpu() is added to discard the FPU context
and disable the FPU, which will be used in a later patch when the FPU
state will become architecturally UNPREDICTABLE (change of FR mode) to
force a reload of [stale] context in the new FR mode.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The FPU and DSP are enabled via the CP0 Status CU1 and MX bits by
kvm_mips_set_c0_status() on a guest exit, presumably in case there is
active state that needs saving if pre-emption occurs. However neither of
these bits are cleared again when returning to the guest.
This effectively gives the guest access to the FPU/DSP hardware after
the first guest exit even though it is not aware of its presence,
allowing FP instructions in guest user code to intermittently actually
execute instead of trapping into the guest OS for emulation. It will
then read & manipulate the hardware FP registers which technically
belong to the user process (e.g. QEMU), or are stale from another user
process. It can also crash the guest OS by causing an FP exception, for
which a guest exception handler won't have been registered.
First lets save and disable the FPU (and MSA) state with lose_fpu(1)
before entering the guest. This simplifies the problem, especially for
when guest FPU/MSA support is added in the future, and prevents FR=1 FPU
state being live when the FR bit gets cleared for the guest, which
according to the architecture causes the contents of the FPU and vector
registers to become UNPREDICTABLE.
We can then safely remove the enabling of the FPU in
kvm_mips_set_c0_status(), since there should never be any active FPU or
MSA state to save at pre-emption, which should plug the FPU leak.
DSP state is always live rather than being lazily restored, so for that
it is simpler to just clear the MX bit again when re-entering the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # v3.10+: 044f0f03eca0: MIPS: KVM: Deliver guest interrupts
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since all the files are in arch/mips/kvm/, there's no need of the prefixes
"kvm_" and "kvm_mips_".
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>