Add USB OTG, peripheral and host devices. This patch also adds
usb_phy_clk which is required for resetting the PHY. VBUS power up
and shutdown routines depends on PMIC module. As PMIC driver is
unavailable, configure USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
OTG driver takes care of putting hardware into low power mode. Hence
make peripheral and host devices as children of OTG device and let
runtime PM takes care of notifying peripheral and host state to
OTG device. VBUS power up and shutdown routines are implemented by
modem processor. As RPC infrastructure is not available, configure
USB in peripheral only mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Initial framebuffer components. Add board-trout-panel.c
as well as platform parts to enable the framebuffer. This
code comes directly from Google's tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CLK_MINMAX is used to denote clocks that have a wide variation
in possible frequencies. This handling just sets the min and
max values to the same value.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This clock is used in the framebuffer driver as mddi_clk.
This just changes the name to match that. This also
mirrors a change in Google tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This adds in the CLK_MINMAX flag to the pmdh_clk since it's actual
a min/max clock instead of a single frequency clock.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
trout has gpiolib support and interrupt support, but was
missing the gpio_to_irq function. This adds that functions
which should allow proper translation.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Change msm_iommu_map to use GFP_ATOMIC instead of
GFP_KERNEL due to the fact that the call occurs within
a spinlock-protected region.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Remove some unneeded assignments and messages, restructure
a failure path in iova_to_phys, and make __flush_iotlb
return int in preparation for adding IOMMU clock control.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add support for allowing IOMMU memory transactions to be
cache coherent, eliminating the need for software cache
management in certain situations. This can lead to
improvements in performance and power usage, assuming the
multimedia core's access pattern exhibits spatial locality
and that its working set fits into the cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the register field definitions and memory attribute
definitions that will be needed to support IOMMU
transactions with cache-coherent memory access.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Make the IOMMU driver select the IOMMU API in the kernel
configuration.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
An IOMMU device can only be attached to one IOMMU domain at
any given time. Check whether the device is already
attached to a domain before allowing it to be attached to
another domain. If so, return busy.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add a Kconfig item to allow the IOMMU page tables to be
coherent in the L2 cache. This generally reduces IOTLB miss
latencies and has been shown to improve multimedia
performance.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Don't flush the page tables on an IOMMU domain if there are
no IOMMU devices attached to the domain. The act of
attaching to the domain will cause an implicit flush of
those areas if the page tables are configured to not be L2
cacheable.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Mark the init and exit functions as __init and __exit where
appropriate.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the platform data and resources needed for the second
2D graphics core's IOMMU.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on recommendations from chip designers,
optimize the Machine ID to translation context
mappings for the first 2D core's IOMMU. Remove the
"gfx2d0_texv3_smmu" context, as it is no longer needed
under the new mapping scheme.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on recommendations from chip designers,
optimize the Machine ID to translation context
mappings for the 3D core's IOMMU. Remove the
the "gfx3d_smmu" context device, as it is no longer
needed under the new mapping scheme.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
[dwalker@codeaurora.org: updated commit text]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Rename all the IOMMU platform devices so that the names are
more consistent with the rest of the codebase.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add register addresses and IRQ numbers for the IOMMU used
for the second 2D graphics core.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
On msm8x60, the MID field on the AXI connection to the
IOMMU can be up to five bits wide. Thus, allow the IOMMU
context platform data to map up to 32 MIDs.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Beginning with the MSM8x60, the hardware block responsible for gpio
support changes. Provide gpiolib support for the new v2 architecture.
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pavan Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This is required for modules to use ioremap()
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Define VMALLOC_END as an unsigned long to match expected type.
Eliminates a warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type
'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Put some variables inside of the same ifdef as the code that uses
them.
arch/arm/mach-msm/smd_debug.c: In function 'smsm_print_sleep_info':
arch/arm/mach-msm/smd_debug.c:274: warning: unused variable 'int_info'
arch/arm/mach-msm/smd_debug.c:273: warning: unused variable 'gpio'
Signed-off-by: David Brown <davidb@codeaurora.org>
[dwalker@codeaurora.org: changed the commit text a little.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Eliminate some unreferenced variables.
arch/arm/mach-msm/sirc.c:43: warning: 'save_type' defined but not used
arch/arm/mach-msm/sirc.c:44: warning: 'save_polarity' defined but not used
Signed-off-by: David Brown <davidb@codeaurora.org>
[dwalker@codeaurora.org: changed the commit text a little.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM smd driver logs numerous messages during startup that are
useful for debug purposes. Change some of these to pr_debug() to
match their purpose, and remove others that aren't really useful.
Cc: Brian Swetland <swetland@google.com>
Cc: Arve Hjønnevåg <arve@android.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
If the board has a debug uart the user is given a choice of which
uart to use. The user can also select NONE, which means not to use one.
In most of our header files when NONE is selected nothing is defined
for MSM_DEBUG_UART_PHYS or MSM_DEBUG_UART_BASE. This causes a compile
failure in debug-macro.S which expect something to be defined there.
Example of the failure,
arch/arm/kernel/built-in.o: In function `hexbuf':
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_PHYS'
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_BASE'
This fixes the compile failure by adding an ifdef to debug-macro.S
that removes all the debug uart code in the case of NONE.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Originally there was an ifdef case to handle when no debug uart
was selected. In commit 0ea1293009
that case was removed which causes the following build failure,
linux-2.6/arch/arm/kernel/debug.S: Assembler messages:
linux-2.6/arch/arm/kernel/debug.S:174: Error: bad instruction `addruart r1,r2'
linux-2.6/arch/arm/kernel/debug.S:176: Error: bad instruction `waituart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:177: Error: bad instruction `senduart r1,r3'
linux-2.6/arch/arm/kernel/debug.S:178: Error: bad instruction `busyuart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:190: Error: bad instruction `addruart r1,r2'
This is a partial revert to add back the case which was removed with
two caveats. First the API for the addruart macro was updated, and
the new addruart case now return 0xfff00000 so that a know IO mapping
is created instead of a random one.
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jason Wang <jason77.wang@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The shift of 24 causes the shift and multiply operation to sometimes
overflow, resulting in incorrect timer values and poor performance.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This prevents build failures since it's currently possible to select
8x50, 7x30, or 7x00 without selecting a specific board. These changes
just force a target selection, which is currently defaulting to the most
common one (7x30 only has one).
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
In commit be37030274
"ARM: Remove DISCONTIGMEM support", it removed this "node" member
which cased the following compile failure in mach-msm,
linux/arch/arm/mach-msm/board-halibut.c: In function 'halibut_fixup':
linux/arch/arm/mach-msm/board-halibut.c:86: error: 'struct membank' has no member named 'node'
linux/arch/arm/mach-msm/board-halibut.c:86: error: implicit declaration of function 'PHYS_TO_NID'
I've removed the access to the node member which corrects the
compile failure.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Add the platform data for the IOMMUs found on the Qualcomm
msm8x60 SoC.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Register a driver for the MSM IOMMU devices and a driver
for the translation context devices. Set up the global
IOMMU registers and initialize the context banks.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add support for the IOMMUs found on the upcoming Qualcomm
MSM8x60 chips. These IOMMUs allow virtualization of the
address space used by most of the multimedia cores on these
chips.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM8X60 FFA contains different components than the MSM8X60 SURF,
and therefore requires a different ARCH type and machine ID.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM8x60 has a different physical memory offset than other targets.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Pavankumar Kondeti