-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Commit c49c097610 ("ipmi: Don't call receive handler in the
panic context") means that the panic_recv_free is not called during a
panic and the atomic count does not drop to 0.
Fix this by only expecting one decrement of the atomic variable
which comes from panic_smi_free.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/char/ipmi/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
cc: openipmi-developer@lists.sourceforge.net
Commit 1abf71e moved the creation of new_smi->dev to earlier in the init
sequence in order to provide infrastructure for log printing.
However, the init_name was created with a hard-coded value of zero. This
presents a problem in systems with more than one interface, producing a
call trace in dmesg.
To correct the problem, simply use smi_num instead of the hard-coded
value of zero.
Tested on a lenovo x3950.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
There was actually a more general problem, the platform device wasn't
being set correctly, either, and there was a possible (though extremely
unlikely) race on smi_num. Add locks to clean up the race and use the
proper value for the platform device, too.
Tested on qemu in various configurations.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ast2500 SoCs contain the same IPMI BT device.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19-
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The registers for the bt-bmc device live under the Aspeed LPC
controller. Devicetree bindings have recently been introduced for the
LPC controller where the "host" portion of the LPC register space is
described as a syscon device. Future devicetrees describing the bt-bmc
device should nest its node under the appropriate "simple-mfd", "syscon"
compatible node.
This change allows the bt-bmc driver to function with both syscon and
non-syscon- based devicetree descriptions by always using a regmap for
register access, either retrieved from the parent syscon device or
instantiated if none exists.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Declare ipmi_smi_handlers structures as const as they are only passed as
an argument to the function ipmi_register_smi. This argument is of type
const, so ipmi_smi_handlers structures having similar properties can be
declared const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct ipmi_smi_handlers i@p={...};
@ok1@
identifier r1.i;
position p;
@@
ipmi_register_smi(&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ipmi_smi_handlers i;
Size details after cross compiling the .o file for powerpc architecture
File size before:
text data bss dec hex filename
2777 288 0 3065 bf9 drivers/char/ipmi/ipmi_powernv.o
File size after:
text data bss dec hex filename
2873 192 0 3065 bf9 drivers/char/ipmi/ipmi_powernv.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
convertion printk() to pr_xxx() and removal of an unused module
parameter. Some small bug fixes and enhancements.
This also adds a post softdep from the IPMI core module to the
IPMI device interface. Many people have complained that the device
interface isn't automatically avaiable when IPMI is loaded. I don't
want to make the device interface mandatory, though, plenty of people
use IPMI internally (like with ACPI) and don't need a device interface
or the added possible security entry. A softdep should make it work
"out of the box" but allow people to not have it if they don't want it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlhSE9cACgkQIXnXXONXERe6iACgsiU5/LG4tbKu9EyZXp5isRw6
AdsAn1dT08aobOzJhFI3dVx6oTnJQDDC
=ifi5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Various small fixes for IPMI. Cleanups in the documentation and
convertion printk() to pr_xxx() and removal of an unused module
parameter. Some small bug fixes and enhancements.
This also adds a post softdep from the IPMI core module to the IPMI
device interface. Many people have complained that the device
interface isn't automatically avaiable when IPMI is loaded. I don't
want to make the device interface mandatory, though, plenty of people
use IPMI internally (like with ACPI) and don't need a device interface
or the added possible security entry. A softdep should make it work
'out of the box' but allow people to not have it if they don't want
it"
* tag 'for-linus-4.10' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: create hardware-independent softdep for ipmi_devintf
ipmi: Fix sequence number handling
ipmi: Pick up slave address from SMBIOS on an ACPI device
ipmi_si: Clean up printks
Move platform device creation earlier in the initialization
ipmi: Update documentation
ipmi_ssif: Remove an unused module parameter
ipmi: Periodically check for events, not messages
When a computer has an IPMI system interface, the device interface
is most probably also desired. Autoloading of ipmi_devintf currently
works only if ipmi_si has allocated a platform device. That doesn't
happen if the SI interface was detected e.g. via ACPI. But ACPI
detection is preferred these days, see e.g. kernel.org bug 46741.
This patch introduces a softdep in place of the existing modalias
for ipmi_devintf.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Suggested-by: Takashi Iwai <tiwai@suse.com>
I moved this to ipmi_msghandler.c, so it works for all IPMI
interfaces. Retested by Martin.
Tested-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI message handler uses a message id that the lower-layer
preserved to track the sequence number of the message. The macros
that handled these sequence numbers were somewhat broken as they
could result in sequence number truncation and they were not
doing an "and" of the proper number of bits.
I think this actually is not a problem, because the truncation
should be harmless and the improper "and" didn't hurt anything
because sequence number generation used the same improper "and"
and wouldn't generate a sequence number that would get
truncated wrong. However, it should be fixed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When added by ACPI, the information does not contain the slave address
of the BMC. However, that information is available from SMBIOS. So
if we add a device that doesn't have a slave address, look at the other
devices that are duplicate interfaces and see if they have a slave
address.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some logs are printed out early using smi->dev, but on a platform device
that is not created until later. So move the creation of that device
structure earlier in the sequence so it can be used for printing.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit d9b7e4f717 ("ipmi: Periodically check to see if irqs and
messages are set right") to verify the contents of global events.
However, the wrong function was being called in some cases, checking
for messages, not events.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Jason DiPietro <J.DiPietro@F5.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
devm_ioremap_resource returns ERR_PTR so we can't check for NULL.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch adds a simple device driver to expose the iBT interface on
Aspeed SOCs (AST2400 and AST2500) as a character device. Such SOCs are
commonly used as BMCs (BaseBoard Management Controllers) and this
driver implements the BMC side of the BT interface.
The BT (Block Transfer) interface is used to perform in-band IPMI
communication between a host and its BMC. Entire messages are buffered
before sending a notification to the other end, host or BMC, that
there is data to be read. Usually, the host emits requests and the BMC
responses but the specification provides a mean for the BMC to send
SMS Attention (BMC-to-Host attention or System Management Software
attention) messages.
For this purpose, the driver introduces a specific ioctl on the
device: 'BT_BMC_IOCTL_SMS_ATN' that can be used by the system running
on the BMC to signal the host of such an event.
The device name defaults to '/dev/ipmi-bt-host'
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
[clg: - checkpatch fixes
- added a devicetree binding documentation
- replace 'bt_host' by 'bt_bmc' to reflect that the driver is
the BMC side of the IPMI BT interface
- renamed the device to 'ipmi-bt-host'
- introduced a temporary buffer to copy_{to,from}_user
- used platform_get_irq()
- moved the driver under drivers/char/ipmi/ but kept it as a misc
device
- changed the compatible cell to "aspeed,ast2400-bt-bmc"
]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[clg: - checkpatch --strict fixes
- removed the use of devm_iounmap, devm_kfree in cleanup paths
- introduced an atomic-t to limit opens to 1
- introduced a mutex to protect write/read operations]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
Parameter trydefaults=1 causes the ipmi_init to initialize ipmi through
the legacy port io space that was designated for ipmi. Architectures
that do not map legacy port io can panic when trydefaults=1.
Rather than implement build-time conditional exceptions for each
architecture that does not map legacy port io, we have removed legacy
port io from the driver.
Parameter 'trydefaults' has been removed. Attempts to use it hereafter
will evoke the "Unknown symbol in module, or unknown parameter" message.
The patch was built against a number of architectures and tested for
regressions and functionality on x86_64 and ARM64.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Removed the config entry and the address source entry for default,
since neither were used any more.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.
This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 7ea0ed2b5b ("ipmi: Make the message handler easier to use for
SMI interfaces") changed handle_new_recv_msgs() to call handle_one_recv_msg()
for a smi_msg while the smi_msg is still connected to waiting_rcv_msgs list.
That could lead to following list corruption problems:
1) low-level function treats smi_msg as not connected to list
handle_one_recv_msg() could end up calling smi_send(), which
assumes the msg is not connected to list.
For example, the following sequence could corrupt list by
doing list_add_tail() for the entry still connected to other list.
handle_new_recv_msgs()
msg = list_entry(waiting_rcv_msgs)
handle_one_recv_msg(msg)
handle_ipmb_get_msg_cmd(msg)
smi_send(msg)
spin_lock(xmit_msgs_lock)
list_add_tail(msg)
spin_unlock(xmit_msgs_lock)
2) race between multiple handle_new_recv_msgs() instances
handle_new_recv_msgs() once releases waiting_rcv_msgs_lock before calling
handle_one_recv_msg() then retakes the lock and list_del() it.
If others call handle_new_recv_msgs() during the window shown below
list_del() will be done twice for the same smi_msg.
handle_new_recv_msgs()
spin_lock(waiting_rcv_msgs_lock)
msg = list_entry(waiting_rcv_msgs)
spin_unlock(waiting_rcv_msgs_lock)
|
| handle_one_recv_msg(msg)
|
spin_lock(waiting_rcv_msgs_lock)
list_del(msg)
spin_unlock(waiting_rcv_msgs_lock)
Fixes: 7ea0ed2b5b ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
[Added a comment to describe why this works.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19
Tested-by: Ye Feng <yefeng.yl@alibaba-inc.com>
Unlike everywhere else in the IPMI specification, the I2C address
specified in the SPMI table is not shifted to the left one bit with
the LSB zero. Instead it is not shifted with the MSB zero.
Reported-by: Sanjeev <singhsan@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Commit d61a3ead26 ("[PATCH] IPMI: reserve I/O ports separately")
changed the way I/O ports were reserved and includes this comment in
log:
Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI
controller. This causes problems when trying to register the entire I/O
region. Therefore we must register each I/O port separately.
There is a similar problem with memio regions on an arm64 platform
(AMD Seattle). Where I see:
ipmi message handler version 39.2
ipmi_si AMDI0300:00: probing via device tree
ipmi_si AMDI0300:00: ipmi_si: probing via ACPI
ipmi_si AMDI0300:00: [mem 0xe0010000] regsize 1 spacing 4 irq 23
ipmi_si: Adding ACPI-specified kcs state machine
IPMI System Interface driver.
ipmi_si: Trying ACPI-specified kcs state machine at mem \
address 0xe0010000, slave address 0x0, irq 23
ipmi_si: Could not set up I/O space
The problem is that the ACPI core registers disjoint regions for the
platform device:
e0010000-e0010000 : AMDI0300:00
e0010004-e0010004 : AMDI0300:00
and the ipmi_si driver tries to register one region e0010000-e0010004.
Based on a patch from Mark Salter <msalter@redhat.com>, who also wrote
all the above text.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Mark Salter <msalter@redhat.com>
Commit 1717f2096b ("panic, x86: Fix re-entrance problem due to panic
on NMI") introduced nmi_panic() which prevents concurrent and recursive
execution of panic(). It also saves registers for the crash dump on x86
by later commit 58c5661f21 ("panic, x86: Allow CPUs to save registers
even if looping in NMI context").
ipmi_watchdog driver can call panic() from NMI handler, so replace it
with nmi_panic().
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the tryacpi module parameter to turn off acpi_ipmi_probe such
that hard-coded options (type, ports, address, etc.) have complete
control over the smi_info data structures setup by the driver.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Under some circumstances, the IPMI state machine could return
a call without delay option but the driver would still do a long
delay because the result wasn't checked. Instead of calling
the state machine after transaction done, just go back to the
top of the processing to start over.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Enclosing '#include <linux/acpi.h>' within '#ifdef CONFIG_ACPI' is
unnecessary, since it has its own conditional compile for CONFIG_ACPI.
Commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI handling to a
platform device") exposed this as a problem for platforms that do not
support ACPI when it introduced a call to ACPI_PTR() macro outside of
the CONFIG_ACPI conditional compile. This would have been perfectly
acceptable if acpi.h were not conditionally excluded for the non-acpi
platform, because the conditional compile within acpi.h defines
ACPI_PTR() to return NULL when compiled for non acpi platforms.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Fixed commit reference in header to conform to standard.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We call cleanup_one_si from ipmi_pci_remove, which calls ->addr_source_cleanup,
which gets set to point to ipmi_pci_cleanup, which does a pci_disable_device.
On return from this, we do a second pci_disable_device, which
results in the trace below.
ipmi_si 0000:00:16.0: disabling already-disabled device
Call Trace:
[<ffffffff818ce54c>] dump_stack+0x45/0x57
[<ffffffff810525f7>] warn_slowpath_common+0x97/0xe0
[<ffffffff810526f6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff81497ca1>] pci_disable_device+0xb1/0xc0
[<ffffffffa00851a5>] ipmi_pci_remove+0x25/0x30 [ipmi_si]
[<ffffffff8149a696>] pci_device_remove+0x46/0xc0
[<ffffffff8156801f>] __device_release_driver+0x7f/0xf0
[<ffffffff81568978>] driver_detach+0xb8/0xc0
[<ffffffff81567e50>] bus_remove_driver+0x50/0xa0
[<ffffffff8156914e>] driver_unregister+0x2e/0x60
[<ffffffff8149a3e5>] pci_unregister_driver+0x25/0x90
[<ffffffffa0085804>] cleanup_ipmi_si+0xd4/0xf0 [ipmi_si]
[<ffffffff810c727a>] SyS_delete_module+0x12a/0x200
[<ffffffff818d4d72>] system_call_fastpath+0x12/0x17
Signed-off-by: Dave Jones <dsj@fb.com>
Lots of char arrays could be set as const since they contain only literal
char arrays.
We could in the same time make const some struct members who are pointer
to those const char arrays.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<ffffffff8100fc59>] handle_irq+0x49/0xa0
[<ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
In order to allow panic actions to be processed, the ipmi watchdog
driver sets a new timeout value on panic. The 255s timeout
was designed to allow kdump and others actions on panic, as in
http://lkml.iu.edu/hypermail/linux/kernel/0711.3/0258.html
This is counter-intuitive for a end-user who sets watchdog timeout
value to something like 30s and who expects BMC to reset the system
within 30s of a panic.
This commit allows user to configure the timeout on panic.
Signed-off-by: Jean-Yves Faye <jean-yves.faye@c-s.fr>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The policy for drivers is to have MODULE_DEVICE_TABLE() just after the
struct used in it. For clarity.
Suggested-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI driver would let the final timeout just happen, but it could
easily just stop the timer. If the timer stop fails that's ok, that
should be rare.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The timer and thread were not being started for internal messages,
so in interrupt mode if something hung the timer would never go
off and clean things up. Factor out the internal message sending
and start the timer for those messages, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Gouji, Masayuki <gouji.masayuki@jp.fujitsu.com>
Cc: stable@vger.kernel.org
This patch replaces timeval with timespec64 as 32 bit 'struct timeval'
will not give current time beyond 2038.
The patch changes the code to use ktime_get_real_ts64() which returns
a 'struct timespec64' instead of do_gettimeofday() which returns a
'struct timeval'
This patch also alters the format string in pr_info() for now.tv_sec
to incorporate 'long long' on 32 bit architectures.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are broken on some platforms, this gives people a chance to work
around it until the firmware is fixed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Fix autoloading ipmi modules when using device tree.
Signed-off-by: Brijesh Singh <brijeshkumar.singh@amd.com>
Moved this change up into the CONFIG_OF section to account
for changes to the probing code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Linus Torvalds