Let's introduce the basics for advertizing discovered PANs and
coordinators, which is:
- A new "scan" netlink message group.
- A couple of netlink command/attribute.
- The main netlink helper to send a netlink message with all the
necessary information to forward the main information to the user.
Two netlink attributes are proactively added to support future UWB
complex channels, but are not actually used yet.
Co-developed-by: David Girault <david.girault@qorvo.com>
Signed-off-by: David Girault <david.girault@qorvo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221129135535.532513-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
As a first strep in introducing proper PAN management and association,
we need to be able to create coordinator interfaces which might act as
coordinator or PAN coordinator.
Hence, let's add the minimum support to allow the creation of these
interfaces.
Even though the necessary logic to handle several interfaces on the same
device is added to make this future move easier, in practice only
several interfaces of type MONITOR are allowed at the same time. The
other combinations are not allowed (interface creation is possible but
only one can be opened at a time) because, with a single PHY featuring a
single set of address filters, we cannot afford handling two distinct
interfaces (with different address filters or filtering requirements):
* Having 2 NODEs, 2 COORDs or 1 NODE + 1 COORD
-> cannot work because the address filters would be different
* Having 1 MONITOR + either 1 NODE or 1 COORD
-> cannot work because the filtering levels are incompatible
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221026093502.602734-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
While going through the whole interface opening logic in my head I was
consistently bothered by the condition checking whether there was only
one interface of type NODE/COORD opened at the same time. What actually
bothered me was the fact that in one case we would use the wpan_dev
pointer directly while in the other case we would use the sdata pointer,
making it harder to differentiate both. In practice the condition should
be straightforward to read. IMHO dropping the wpan_dev indirection
allows to clarify the check.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221026093502.602734-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
It may appear clearer to free the skb at the end of the path rather than
in the middle, within a helper.
Move kfree_skb() from the end of __ieee802154_rx_handle_packet() to
right after it in the calling function ieee802154_rx(). Doing so implies
reworking a little bit the exit path.
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221026093502.602734-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This allows the use of a matchJSON field in tests to match
against JSON output from the command under test, if that
command outputs JSON.
You specify what you want to match against as a JSON array
or object in the test's matchJSON field. You can leave out
any fields you don't want to match against that are present
in the output and they will be skipped.
An example matchJSON value would look like this:
"matchJSON": [
{
"Value": {
"neighIP": {
"family": 4,
"addr": "AQIDBA==",
"width": 32
},
"nsflags": 142,
"ncflags": 0,
"LLADDR": "ESIzRFVm"
}
}
]
The real output from the command under test might have some
extra fields that we don't care about for matching, and
since we didn't include them in our matchJSON value, those
fields will not be attempted to be matched. If everything
we included above has the same values as the real command
output, the test will pass.
The matchJSON field's type must be the same as the command
output's type, otherwise the test will fail. So if the
command outputs an array, then the value of matchJSON must
also be an array.
If matchJSON is an array, it must not contain more elements
than the command output's array, otherwise the test will
fail.
Signed-off-by: Jeremy Carter <jeremy@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20221024111603.2185410-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ave_open() in ave_resume() executes __phy_resume() via phy_start(), so no
need to call phy_resume() explicitly. Remove it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072314.24969-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable total_copied is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024135046.2159523-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
state is deferenced earlier in the function, the NULL check
is pointless. Since we don't have any crash reports presumably
it's safe to assume state is not NULL.
Fixes: f392a18464 ("net: phylink: provide phylink_validate_mask_caps() helper")
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221025185126.1720553-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
My recent patch missed that mptcp_subflow_create_socket()
was creating a 'kernel' socket, then converted it to 'user' socket.
Fixes: 0cafd77dcd ("net: add a refcount tracker for kernel sockets")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/20221025180546.652251-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Re-pull from Stefan to fix the warnings.
Stefan Schmidt says:
====================
pull-request v2: ieee802154-next 2022-10-26
* tag 'ieee802154-for-net-next-2022-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next:
net: mac802154: Fixup function parameter name in docs
====================
Link: https://lore.kernel.org/r/20221026075638.578840-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
==
One of the biggest cycles for ieee802154 in a long time. We are landing the
first pieces of a big enhancements in managing PAN's. We might have another pull
request ready for this cycle later on, but I want to get this one out first.
Miquel Raynal added support for sending frames synchronously as a dependency
to handle MLME commands. Also introducing more filtering levels to match with
the needs of a device when scanning or operating as a pan coordinator.
To support development and testing the hwsim driver for ieee802154 was also
enhanced for the new filtering levels and to update the PIB attributes.
Alexander Aring fixed quite a few bugs spotted during reviewing changes. He
also added support for TRAC in the atusb driver to have better failure
handling if the firmware provides the needed information.
Jilin Yuan fixed a comment with a repeated word in it.
==================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request of 29 patches for net-next/master.
The first patch is by Daniel S. Trevitz and adds documentation for
switchable termination resistors.
Zhang Changzhong's patch fixes a debug output in the j13939 stack.
Oliver Hartkopp finally removes the pch_can driver, which is
superseded by the generic c_can driver.
Gustavo A. R. Silva replaces a zero-length array with
DECLARE_FLEX_ARRAY() in the ucan driver.
Kees Cook's patch removes a no longer needed silencing of
"-Warray-bounds" warnings for the kvaser_usb driver.
The next 2 patches target the m_can driver. The first is by me cleans
up the LEC error handling, the second is by Vivek Yadav and extends
the LEC error handling to the data phase of CAN-FD frames.
The next 9 patches all target the gs_usb driver. The first 5 patches
are by me and improve the Kconfig prompt and help text, set
netdev->dev_id to distinguish multi CAN channel devices, allow
loopback and listen only at the same time, and clean up the
gs_can_open() function a bit. The remaining 4 patches are by Jeroen
Hofstee and add support for 2 new features: Bus Error Reporting and
Get State.
Jimmy Assarsson and Anssi Hannula contribute 10 patches for the
kvaser_usb driver. They first add Listen Only and Bus Error Reporting
support, handle CMD_ERROR_EVENT errors, improve CAN state handling,
restart events, and configuration of the bit timing parameters.
Another patch by me which fixes the indention in the m_can driver.
A patch by Dongliang Mu cleans up the ucan_disconnect() function in
the ucan driver.
The last patch by Biju Das is for the rcan_canfd driver and cleans up
the reset handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace devm_reset_control_get_exclusive->devm_reset_control_
get_optional_exclusive so that we can avoid unnecessary
SoC specific check in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221025155657.1426948-4-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
From API pairing, change unregister_netdev() to unregister_candev()
since the registration function is register_candev(). Actually, they
are the same.
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024110033.727542-1-dzm91@hust.edu.cn
[mkl: adjust subject + commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device will respond with a CMD_ERROR_EVENT command, with error_code
KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ
contains invalid bittiming parameters.
However, this command does not contain any channel reference.
To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare
the requested bittiming parameters with the device reported parameters.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add struct kvaser_usb_busparams containing the busparameters used in
CMD_{SET,GET}_BUSPARAMS* commands.
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-11-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When auto-restart is enabled, the kvaser_usb_leaf driver considers
transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery
event (restart).
However, these events may occur at interface startup time before
kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing
restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no
actual restart having occurred.
Fix that by making the auto-restart condition checks more strict so that
they only trigger when the interface was actually in the BUS_OFF state.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 it was observed
that if the device was bus-off when stopped, at next start (either via
interface down/up or manual bus-off restart) the initial
CMD_CHIP_STATE_EVENT received just after CMD_START_CHIP_REPLY will have
the M16C_STATE_BUS_OFF bit still set, causing the interface to
immediately go bus-off again.
The bit seems to internally clear quickly afterwards but we do not get
another CMD_CHIP_STATE_EVENT.
Fix the issue by ignoring any initial bus-off state until we see at
least one bus-on state. Also, poll the state periodically until that
occurs.
It is possible we lose one actual immediately occurring bus-off event
here in which case the HW will auto-recover and we see the recovery
event. We will then catch the next bus-off event, if any.
This issue did not reproduce with 0bfd:0017 Kvaser Memorator
Professional HS/HS FW 2.0.50.
Fixes: 71873a9b38 ("can: kvaser_usb: Add support for more Kvaser Leaf v2 devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a
CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device,
causing a stopped device to appear as CAN_STATE_BUS_OFF instead of
CAN_STATE_STOPPED.
Fix that by not handling error events on stopped devices.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send
any unsolicited events when error counters decrease or when the device
transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).
This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE
state.
Fix that by asking for chip state (inc. counters) event every 0.5 secs
when error counters are non-zero.
Since there are non-error-counter devices, also always poll in
ERROR_PASSIVE even if the counters show zero.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kvaser_usb_leaf_rx_error_update_can_state() sets error state according
to error counters when the hardware does not indicate a specific state
directly.
However, this is currently gated behind a check for
M16C_STATE_BUS_ERROR which does not always seem to be set when error
counters are increasing, and may not be set when error counters are
decreasing.
This causes the CAN_STATE_ERROR_WARNING state to not be set in some
cases even when appropriate.
Change the code to set error state from counters even without
M16C_STATE_BUS_ERROR.
The Error-Passive case seems superfluous as it is already set via
M16C_STATE_BUS_PASSIVE flag above, but it is kept for now.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device will send an error event command, to indicate certain errors.
This indicates a misbehaving driver, and should never occur.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the CMD_GET_CAPABILITIES_REQ command to query the device for certain
capabilities. We are only interested in LISTENONLY mode and wither the
device reports CAN error counters.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function parameter name was wrong in kdocs.
net/mac802154/util.c:27: warning: Function parameter or member 'hw' not described in 'ieee802154_wake_queue'
net/mac802154/util.c:27: warning: Excess function parameter 'local' description in 'ieee802154_wake_queue'
net/mac802154/util.c:53: warning: Function parameter or member 'hw' not described in 'ieee802154_stop_queue'
net/mac802154/util.c:53: warning: Excess function parameter 'local' description in 'ieee802154_stop_queue'
Fixing name and description.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Variable tx_use is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024143501.2163720-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable num_entries is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024125951.2155434-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set max_mtu/min_mtu directly to avoid making the validity judgment
when set mtu, because the judgment is made in net/core: dev_validate_mtu,
so to simplify the code.
Signed-off-by: caihuoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20221024103349.4494-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raju Lakkaraju says:
====================
net: lan743x: PCI11010 / PCI11414 devices Enhancements
This patch series continues with the addition of supported features for the
Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver.
====================
Link: https://lore.kernel.org/r/20221024082516.661199-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for MDI-X status and configuration for KSZ9131 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add pause get and set functions
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One of the worst offenders of "fake flexible arrays" is struct sockaddr,
as it is the classic example of why GCC and Clang have been traditionally
forced to treat all trailing arrays as fake flexible arrays: in the
distant misty past, sa_data became too small, and code started just
treating it as a flexible array, even though it was fixed-size. The
special case by the compiler is specifically that sizeof(sa->sa_data)
and FORTIFY_SOURCE (which uses __builtin_object_size(sa->sa_data, 1))
do not agree (14 and -1 respectively), which makes FORTIFY_SOURCE treat
it as a flexible array.
However, the coming -fstrict-flex-arrays compiler flag will remove
these special cases so that FORTIFY_SOURCE can gain coverage over all
the trailing arrays in the kernel that are _not_ supposed to be treated
as a flexible array. To deal with this change, convert sa_data to a true
flexible array. To keep the structure size the same, move sa_data into
a union with a newly introduced sa_data_min with the original size. The
result is that FORTIFY_SOURCE can continue to have no idea how large
sa_data may actually be, but anything using sizeof(sa->sa_data) must
switch to sizeof(sa->sa_data_min).
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Dylan Yudaken <dylany@fb.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Petr Machata <petrm@nvidia.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: syzbot <syzkaller@googlegroups.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221018095503.never.671-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Round up allocations with kmalloc_size_roundup() so that build_skb()'s
use of ksize() is always accurate and no special handling of the memory
is needed by KASAN, UBSAN_BOUNDS, nor FORTIFY_SOURCE.
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022021004.gonna.489-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Mat Martineau says:
====================
mptcp: Socket option updates
Patches 1 and 3 refactor a recent socket option helper function for more
generic use, and make use of it in a couple of places.
Patch 2 adds TCP_FASTOPEN_NO_COOKIE functionality to MPTCP sockets,
similar to TCP_FASTOPEN_CONNECT support recently added in v6.1
====================
Link: https://lore.kernel.org/r/20221022004505.160988-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mptcp_setsockopt_sol_tcp_defer() was doing the same thing as
mptcp_setsockopt_first_sf_only() except for the returned code in case of
error.
Ignoring the error is needed to mimic how TCP_DEFER_ACCEPT is handled
when used with "plain" TCP sockets.
The specific function for TCP_DEFER_ACCEPT can be replaced by the new
mptcp_setsockopt_first_sf_only() helper and errors can be ignored to
stay compatible with TCP. A bit of cleanup.
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The goal of this socket option is to configure MPTCP + TFO without
cookie per socket.
It was already possible to enable TFO without a cookie per netns by
setting net.ipv4.tcp_fastopen sysctl knob to the right value. Per route
was also supported by setting 'fastopen_no_cookie' option. This patch
adds a per socket support like it is possible to do with TCP thanks to
TCP_FASTOPEN_NO_COOKIE socket option.
The only thing to do here is to relay the request to the first subflow
like it is already done for TCP_FASTOPEN_CONNECT.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are other socket options that need to act only on the first
subflow, e.g. all TCP_FASTOPEN* socket options.
This is similar to the getsockopt version.
In the next commit, this new mptcp_setsockopt_first_sf_only() helper is
used by other another option.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima says:
====================
soreuseport: Fix broken SO_INCOMING_CPU.
setsockopt(SO_INCOMING_CPU) for UDP/TCP is broken since 4.5/4.6 due to
these commits:
* e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
* c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
These commits introduced the O(1) socket selection algorithm and removed
O(n) iteration over the list, but it ignores the score calculated by
compute_score(). As a result, it caused two misbehaviours:
* Unconnected sockets receive packets sent to connected sockets
* SO_INCOMING_CPU does not work
The former is fixed by commit acdcecc612 ("udp: correct reuseport
selection with connected sockets"). This series fixes the latter and
adds some tests for SO_INCOMING_CPU.
====================
Link: https://lore.kernel.org/r/20221021204435.4259-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some highly optimised applications use SO_INCOMING_CPU to make them
efficient, but they didn't test if it's working correctly by getsockopt()
to avoid slowing down. As a result, no one noticed it had been broken
for years, so it's a good time to add a test to catch future regression.
The test does
1) Create $(nproc) TCP listeners associated with each CPU.
2) Create 32 child sockets for each listener by calling
sched_setaffinity() for each CPU.
3) Check if accept()ed sockets' sk_incoming_cpu matches
listener's one.
If we see -EAGAIN, SO_INCOMING_CPU is broken. However, we might not see
any error even if broken; the kernel could miraculously distribute all SYN
to correct listeners. Not to let that happen, we must increase the number
of clients and CPUs to some extent, so the test requires $(nproc) >= 2 and
creates 64 sockets at least.
Test:
$ nproc
96
$ ./so_incoming_cpu
Before the previous patch:
# Starting 12 tests from 5 test cases.
# RUN so_incoming_cpu.before_reuseport.test1 ...
# so_incoming_cpu.c:191:test1:Expected cpu (5) == i (0)
# test1: Test terminated by assertion
# FAIL so_incoming_cpu.before_reuseport.test1
not ok 1 so_incoming_cpu.before_reuseport.test1
...
# FAILED: 0 / 12 tests passed.
# Totals: pass:0 fail:12 xfail:0 xpass:0 skip:0 error:0
After:
# Starting 12 tests from 5 test cases.
# RUN so_incoming_cpu.before_reuseport.test1 ...
# so_incoming_cpu.c:199:test1:SO_INCOMING_CPU is very likely to be working correctly with 3072 sockets.
# OK so_incoming_cpu.before_reuseport.test1
ok 1 so_incoming_cpu.before_reuseport.test1
...
# PASSED: 12 / 12 tests passed.
# Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kazuho Oku reported that setsockopt(SO_INCOMING_CPU) does not work
with setsockopt(SO_REUSEPORT) since v4.6.
With the combination of SO_REUSEPORT and SO_INCOMING_CPU, we could
build a highly efficient server application.
setsockopt(SO_INCOMING_CPU) associates a CPU with a TCP listener
or UDP socket, and then incoming packets processed on the CPU will
likely be distributed to the socket. Technically, a socket could
even receive packets handled on another CPU if no sockets in the
reuseport group have the same CPU receiving the flow.
The logic exists in compute_score() so that a socket will get a higher
score if it has the same CPU with the flow. However, the score gets
ignored after the blamed two commits, which introduced a faster socket
selection algorithm for SO_REUSEPORT.
This patch introduces a counter of sockets with SO_INCOMING_CPU in
a reuseport group to check if we should iterate all sockets to find
a proper one. We increment the counter when
* calling listen() if the socket has SO_INCOMING_CPU and SO_REUSEPORT
* enabling SO_INCOMING_CPU if the socket is in a reuseport group
Also, we decrement it when
* detaching a socket out of the group to apply SO_INCOMING_CPU to
migrated TCP requests
* disabling SO_INCOMING_CPU if the socket is in a reuseport group
When the counter reaches 0, we can get back to the O(1) selection
algorithm.
The overall changes are negligible for the non-SO_INCOMING_CPU case,
and the only notable thing is that we have to update sk_incomnig_cpu
under reuseport_lock. Otherwise, the race prevents transitioning to
the O(n) algorithm and results in the wrong socket selection.
cpu1 (setsockopt) cpu2 (listen)
+-----------------+ +-------------+
lock_sock(sk1) lock_sock(sk2)
reuseport_update_incoming_cpu(sk1, val)
.
| /* set CPU as 0 */
|- WRITE_ONCE(sk1->incoming_cpu, val)
|
| spin_lock_bh(&reuseport_lock)
| reuseport_grow(sk2, reuse)
| .
| |- more_socks_size = reuse->max_socks * 2U;
| |- if (more_socks_size > U16_MAX &&
| | reuse->num_closed_socks)
| | .
| | |- RCU_INIT_POINTER(sk1->sk_reuseport_cb, NULL);
| | `- __reuseport_detach_closed_sock(sk1, reuse)
| | .
| | `- reuseport_put_incoming_cpu(sk1, reuse)
| | .
| | | /* Read shutdown()ed sk1's sk_incoming_cpu
| | | * without lock_sock().
| | | */
| | `- if (sk1->sk_incoming_cpu >= 0)
| | .
| | | /* decrement not-yet-incremented
| | | * count, which is never incremented.
| | | */
| | `- __reuseport_put_incoming_cpu(reuse);
| |
| `- spin_lock_bh(&reuseport_lock)
|
|- spin_lock_bh(&reuseport_lock)
|
|- reuse = rcu_dereference_protected(sk1->sk_reuseport_cb, ...)
|- if (!reuse)
| .
| | /* Cannot increment reuse->incoming_cpu. */
| `- goto out;
|
`- spin_unlock_bh(&reuseport_lock)
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Kazuho Oku <kazuhooku@gmail.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder says:
====================
net: ipa: validation cleanup
This series gathers a set of IPA driver cleanups, mostly involving
code that ensures certain things are known to be correct *early*
(either at build or initializatin time), so they can be assumed good
during normal operation.
The first removes three constant symbols, by making a (reasonable)
assumption that a routing table consists of entries for the modem
followed by entries for the AP, with no unused entries between them.
The second removes two checks that are redundant (they verify the
sizes of two memory regions are in range, which will have been done
earlier for all regions).
The third adds some new checks to routing and filter tables that
can be done at "init time" (without requiring any access to IPA
hardware).
The fourth moves a check that routing and filter table addresses can
be encoded within certain IPA immediate commands, so it's performed
earlier; the checks can be done without touching IPA hardware. The
fifth moves some other command-related checks earlier, for the same
reason.
The sixth removes the definition ipa_table_valid(), because what it
does has become redundant. Finally, the last patch moves two more
validation calls so they're done very early in the probe process.
This will be required by some upcoming patches, which will record
the size of the routing and filter tables at this time so they're
available for subsequent initialization.
====================
Link: https://lore.kernel.org/r/20221021191340.4187935-1-elder@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Verify that the sizes of the routing and filter table memory regions
are valid as part of memory initialization, rather than waiting for
table initialization. The main reason to do this is that upcoming
patches use these memory region sizes to determine the number of
entries in these tables, and we'll want to know these sizes are good
sooner.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
What ipa_table_valid() (and ipa_table_valid_one(), which it calls)
does is ensure that the memory regions that hold routing and filter
tables have reasonable size. Specifically, it checks that the size
of a region is sufficient (or rather, exactly the right size) to
hold the maximum number of entries supported by the driver. (There
is an additional check that's erroneous, but in practice it is never
reached.)
Recently ipa_table_mem_valid() was added, which is called by
ipa_table_init(). That function verifies that all table memory
regions are of sufficient size, and requires hashed tables to have
zero size if hashing is not supported. It only ensures the filter
table is large enough to hold the number of endpoints that support
filtering, but that is adequate.
Therefore everything that ipa_table_valid() does is redundant, so
get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, ipa_cmd_data_valid() is called by ipa_mem_config().
Nothing it does requires access to hardware though, so it can be
done during the init phase of IPA driver startup.
Create a new function ipa_cmd_init(), whose purpose is to do early
initialization related to IPA immediate commands. It will call the
build-time validation function, then will make the two calls made
previously by ipa_cmd_data_valid(). This make ipa_cmd_data_valid()
unnecessary, so get rid of it.
Rename ipa_cmd_header_valid() to be ipa_cmd_header_init_local_valid(),
so its name is clearer about which IPA immediate command it is
associated with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We currently verify the table size and offset fit in the immediate
command fields that must encode them in ipa_table_valid_one(). We
can now make this check earlier, in ipa_table_mem_valid().
The non-hashed IPv4 filter and route tables will always exist, and
their sizes will match the IPv6 tables, as well as the hashed tables
(if supported). So it's sufficient to verify the offset and size of
the IPv4 non-hashed tables fit into these fields.
Rename the function ipa_cmd_table_init_valid(), to reinforce that
it is the TABLE_INIT immediate command fields we're checking.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add checks in ipa_table_init() to ensure the memory regions defined
for IPA filter and routing tables are valid.
For routing tables, the checks ensure:
- The non-hashed IPv4 and IPv6 routing tables are defined
- The non-hashed IPv4 and IPv6 routing tables are the same size
- The number entries in the non-hashed IPv4 routing table is enough
to hold the number entries available to the modem, plus at least
one usable by the AP.
For filter tables, the checks ensure:
- The non-hashed IPv4 and IPv6 filter tables are defined
- The non-hashed IPv4 and IPv6 filter tables are the same size
- The number entries in the non-hashed IPv4 filter table is enough
to hold the endpoint bitmap, plus an entry for each defined
endpoint that supports filtering.
In addition, for both routing and filter tables:
- If hashing isn't supported (IPA v4.2), hashed tables are zero size
- If hashing *is* supported, all hashed tables are the same size as
their non-hashed counterparts.
When validating the size of routing tables, require the AP to have
at least one entry (in addition to those used by the modem).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There's no need to ensure table memory regions fit within the
IPA-local memory range. And there's no need to ensure the modem
header memory region is in range either. These are verified for all
memory regions in ipa_mem_size_valid(), once we have settled on the
size of IPA memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The entries in each IPA routing table are divided between the modem
and the AP. The modem always gets some number of entries located at
the base of the table; the AP gets all those that follow.
There's no reason to think the modem will use anything different
from the first entries in a routing table, so:
- Get rid of IPA_ROUTE_MODEM_MIN (just assume it's 0)
- Get rid of IPA_ROUTE_AP_MIN (just assume it's IPA_ROUTE_MODEM_COUNT)
And finally:
- Open-code IPA_ROUTE_AP_COUNT and remove its definition
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Miquel Raynal