There were two files in the firmware_loader code that did not have SPDX
identifiers on them, so fix that up.
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Makefile in the drivers/base/test/ directory did not have a SPDX
identifier on it, so fix that up.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user updates any cpu's cpu_capacity, then the new value is going to
be applied to all its online sibling cpus. But this need not to be correct
always, as sibling cpus (in ARM, same micro architecture cpus) would have
different cpu_capacity with different performance characteristics.
So, updating the user supplied cpu_capacity to all cpu siblings
is not correct.
And another problem is, current code assumes that 'all cpus in a cluster
or with same package_id (core_siblings), would have same cpu_capacity'.
But with commit '5bdd2b3f0f8 ("arm64: topology: add support to remove
cpu topology sibling masks")', when a cpu hotplugged out, the cpu
information gets cleared in its sibling cpus. So, user supplied
cpu_capacity would be applied to only online sibling cpus at the time.
After that, if any cpu hotplugged in, it would have different cpu_capacity
than its siblings, which breaks the above assumption.
So, instead of mucking around the core sibling mask for user supplied
value, use device-tree to set cpu capacity. And make the cpu_capacity
node as read-only to know the asymmetry between cpus in the system.
While at it, remove cpu_scale_mutex usage, which used for sysfs write
protection.
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Quentin Perret <quentin.perret@arm.com>
Reviewed-by: Quentin Perret <quentin.perret@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platforms may provide system memory where some physical address ranges
perform differently than others, or is cached by the system on the
memory side.
Add documentation describing a high level overview of such systems and the
perforamnce and caching attributes the kernel provides for applications
wishing to query this information.
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register memory side cache attributes with the memory's node if HMAT
provides the side cache iniformation table.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the best performance access attributes and register these with the
memory's node if HMAT provides the locality table. While HMAT does make
it possible to know performance for all possible initiator-target
pairings, we export only the local pairings at this time.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the HMAT Subsystem Address Range provides a valid processor proximity
domain for a memory domain, or a processor domain matches the performance
access of the valid processor proximity domain, register the memory
target with that initiator so this relationship will be visible under
the node's sysfs directory.
Since HMAT requires valid address ranges have an equivalent SRAT entry,
verify each memory target satisfies this requirement.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Brice Goglin <Brice.Goglin@inria.fr>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System memory may have caches to help improve access speed to frequently
requested address ranges. While the system provided cache is transparent
to the software accessing these memory ranges, applications can optimize
their own access based on cache attributes.
Provide a new API for the kernel to register these memory-side caches
under the memory node that provides it.
The new sysfs representation is modeled from the existing cpu cacheinfo
attributes, as seen from /sys/devices/system/cpu/<cpu>/cache/. Unlike CPU
cacheinfo though, the node cache level is reported from the view of the
memory. A higher level number is nearer to the CPU, while lower levels
are closer to the last level memory.
The exported attributes are the cache size, the line size, associativity
indexing, and write back policy, and add the attributes for the system
memory caches to sysfs stable documentation.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Brice Goglin <Brice.Goglin@inria.fr>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heterogeneous memory systems provide memory nodes with different latency
and bandwidth performance attributes. Provide a new kernel interface
for subsystems to register the attributes under the memory target
node's initiator access class. If the system provides this information,
applications may query these attributes when deciding which node to
request memory.
The following example shows the new sysfs hierarchy for a node exporting
performance attributes:
# tree -P "read*|write*"/sys/devices/system/node/nodeY/accessZ/initiators/
/sys/devices/system/node/nodeY/accessZ/initiators/
|-- read_bandwidth
|-- read_latency
|-- write_bandwidth
`-- write_latency
The bandwidth is exported as MB/s and latency is reported in
nanoseconds. The values are taken from the platform as reported by the
manufacturer.
Memory accesses from an initiator node that is not one of the memory's
access "Z" initiator nodes linked in the same directory may observe
different performance than reported here. When a subsystem makes use
of this interface, initiators of a different access number may not have
the same performance relative to initiators in other access numbers, or
omitted from the any access class' initiators.
Descriptions for memory access initiator performance access attributes
are added to sysfs stable documentation.
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems may be constructed with various specialized nodes. Some nodes
may provide memory, some provide compute devices that access and use
that memory, and others may provide both. Nodes that provide memory are
referred to as memory targets, and nodes that can initiate memory access
are referred to as memory initiators.
Memory targets will often have varying access characteristics from
different initiators, and platforms may have ways to express those
relationships. In preparation for these systems, provide interfaces for
the kernel to export the memory relationship among different nodes memory
targets and their initiators with symlinks to each other.
If a system provides access locality for each initiator-target pair, nodes
may be grouped into ranked access classes relative to other nodes. The
new interface allows a subsystem to register relationships of varying
classes if available and desired to be exported.
A memory initiator may have multiple memory targets in the same access
class. The target memory's initiators in a given class indicate the
nodes access characteristics share the same performance relative to other
linked initiator nodes. Each target within an initiator's access class,
though, do not necessarily perform the same as each other.
A memory target node may have multiple memory initiators. All linked
initiators in a target's class have the same access characteristics to
that target.
The following example show the nodes' new sysfs hierarchy for a memory
target node 'Y' with access class 0 from initiator node 'X':
# symlinks -v /sys/devices/system/node/nodeX/access0/
relative: /sys/devices/system/node/nodeX/access0/targets/nodeY -> ../../nodeY
# symlinks -v /sys/devices/system/node/nodeY/access0/
relative: /sys/devices/system/node/nodeY/access0/initiators/nodeX -> ../../nodeX
The new attributes are added to the sysfs stable documentation.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems may provide different memory types and export this information
in the ACPI Heterogeneous Memory Attribute Table (HMAT). Parse these
tables provided by the platform and report the memory access and caching
attributes to the kernel messages.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Heterogeneous Memory Attribute Table (HMAT) header has different
field lengths than the existing parsing uses. Add the HMAT type to the
parsing rules so it may be generically parsed.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting use-after-free bug in uinput module [1]. This is because
kobject_uevent(KOBJ_REMOVE) is called again due to commit 0f4dafc056
("Kobject: auto-cleanup on final unref") after memory allocation fault
injection made kobject_uevent(KOBJ_REMOVE) from device_del() from
input_unregister_device() fail, while uinput_destroy_device() is expecting
that kobject_uevent(KOBJ_REMOVE) is not called after device_del() from
input_unregister_device() completed.
That commit intended to catch cases where nobody even attempted to send
"remove" uevents. But there is no guarantee that an event will ultimately
be sent. We are at the point of no return as far as the rest of the kernel
is concerned; there are no repeats or do-overs.
Also, it is not clear whether some subsystem depends on that commit.
If no subsystem depends on that commit, it will be better to remove
the state_{add,remove}_uevent_sent logic. But we don't want to risk
a regression (in a patch which will be backported) by trying to remove
that logic. Therefore, as a first step, let's avoid the use-after-free bug
by making sure that kobject_uevent(KOBJ_REMOVE) won't be triggered twice.
[1] https://syzkaller.appspot.com/bug?id=8b17c134fe938bbddd75a45afaa9e68af43a362d
Reported-by: syzbot <syzbot+f648cfb7e0b52bf7ae32@syzkaller.appspotmail.com>
Analyzed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 0f4dafc056 ("Kobject: auto-cleanup on final unref")
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7934779a69 ("Driver-Core: disable /sbin/hotplug by
default"), the help text for the /sbin/hotplug fork-bomb says
"This should not be used today [...] creates a high system load, or
[...] out-of-memory situations during bootup". The rationale for this
was that no recent mainstream system used this anymore (in 2010!).
A few years later, the complete uevent helper support was made optional
in commit 86d56134f1 ("kobject: Make support for uevent_helper
optional."). However, if was still left enabled by default, to support
ancient userland.
Time passed by, and nothing should use this anymore, so it can be
disabled by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct device is big, around 760 bytes on x86_64. It's not a critical
structure, but it is embedded everywhere, so making it smaller is always
a good thing.
With a recent patch that moved a field from struct device to the private
structure, some benchmarks showed a very odd regression, despite this
structure having nothing to do with those benchmarks. That caused me to
look into the layout of the structure. Using 'pahole', it showed a
number of holes and ways that the structure could be reordered in order
to align some cachelines better, as well as reduce the size of the
overall structure.
Move 'struct kobj' to the start of the structure, to keep that access
in the first cacheline, and try to organize things a bit more compactly
where possible
By doing these few moves, the result removes at least 8 bytes from
'struct device' on a 64bit system. Given we know there are systems with
at least 30k devices in memory at once, every little byte counts, and
this change could be a savings of 240k of kernel memory for them. On
"normal" systems the overall memory savings would be much less.
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On top of this, a cleanup of kvm_para.h headers, which were exported by
some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcoM5VAAoJEL/70l94x66DU3EH/A8sYdsfeqALWElm2Sy9TYas
mntz+oTWsl3vDy8s8zp1ET2NpF7oBlBEMmCWhVEJaD+1qW3VpTRAseR3Zr9ML9xD
k+BQM8SKv47o86ZN+y4XALl30Ckb3DXh/X1xsrV5hF6J3ofC+Ce2tF560l8C9ygC
WyHDxwNHMWVA/6TyW3mhunzuVKgZ/JND9+0zlyY1LKmUQ0BQLle23gseIhhI0YDm
B4VGIYU2Mf8jCH5Ir3N/rQ8pLdo8U7f5P/MMfgXQafksvUHJBg6B6vOhLJh94dLh
J2wixYp1zlT0drBBkvJ0jPZ75skooWWj0o3otEA7GNk/hRj6MTllgfL5SajTHZg=
=/A7u
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A collection of x86 and ARM bugfixes, and some improvements to
documentation.
On top of this, a cleanup of kvm_para.h headers, which were exported
by some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
KVM: doc: Document the life cycle of a VM and its resources
KVM: selftests: complete IO before migrating guest state
KVM: selftests: disable stack protector for all KVM tests
KVM: selftests: explicitly disable PIE for tests
KVM: selftests: assert on exit reason in CR4/cpuid sync test
KVM: x86: update %rip after emulating IO
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
kvm: don't redefine flags as something else
kvm: mmu: Used range based flushing in slot_handle_level_range
KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
KVM: Reject device ioctls from processes other than the VM's creator
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
...
Pull x86 fixes from Thomas Gleixner:
"A pile of x86 updates:
- Prevent exceeding he valid physical address space in the /dev/mem
limit checks.
- Move all header content inside the header guard to prevent compile
failures.
- Fix the bogus __percpu annotation in this_cpu_has() which makes
sparse very noisy.
- Disable switch jump tables completely when retpolines are enabled.
- Prevent leaking the trampoline address"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/realmode: Make set_real_mode_mem() static inline
x86/cpufeature: Fix __percpu annotation in this_cpu_has()
x86/mm: Don't exceed the valid physical address space
x86/retpolines: Disable switch jump tables when retpolines are enabled
x86/realmode: Don't leak the trampoline kernel address
x86/boot: Fix incorrect ifdeffery scope
x86/resctrl: Remove unused variable
Pull perf tooling fixes from Thomas Gleixner:
"Core libraries:
- Fix max perf_event_attr.precise_ip detection.
- Fix parser error for uncore event alias
- Fixup ordering of kernel maps after obtaining the main kernel map
address.
Intel PT:
- Fix TSC slip where A TSC packet can slip past MTC packets so that
the timestamp appears to go backwards.
- Fixes for exported-sql-viewer GUI conversion to python3.
ARM coresight:
- Fix the build by adding a missing case value for enumeration value
introduced in newer library, that now is the required one.
tool headers:
- Syncronize kernel headers with the kernel, getting new io_uring and
pidfd_send_signal syscalls so that 'perf trace' can handle them"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf pmu: Fix parser error for uncore event alias
perf scripts python: exported-sql-viewer.py: Fix python3 support
perf scripts python: exported-sql-viewer.py: Fix never-ending loop
perf machine: Update kernel map address and re-order properly
tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
tools headers uapi: Update drm/i915_drm.h
tools arch x86: Sync asm/cpufeatures.h with the kernel sources
tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
perf evsel: Fix max perf_event_attr.precise_ip detection
perf intel-pt: Fix TSC slip
perf cs-etm: Add missing case value
Pull CPU hotplug fixes from Thomas Gleixner:
"Two SMT/hotplug related fixes:
- Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
aborts. This is triggered with the 'nosmt' command line option, but
can happen by any abort condition. As the real unplug code is not
compiled in, prevent the fail by keeping the CPU in zombie state.
- Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
completely. With 'nosmt' being a popular option it's required to
unplug the half brought up sibling CPUs (due to the MCE wreckage)
completely"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
Pull locking fixlet from Thomas Gleixner:
"Trivial update to the maintainers file"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Remove deleted file from futex file pattern
Pull core fixes from Thomas Gleixner:
"A small set of core updates:
- Make the watchdog respect the selected CPU mask again. That was
broken by the rework of the watchdog thread management and caused
inconsistent state and NMI watchdog being unstoppable.
- Ensure that the objtool build can find the libelf location.
- Remove dead kcore stub code"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog: Respect watchdog cpumask on CPU hotplug
objtool: Query pkg-config for libelf location
proc/kcore: Remove unused kclist_add_remap()
Three non-regression fixes.
Our optimised memcmp could read past the end of one of the buffers and
potentially trigger a page fault leading to an oops.
Some of our code to read energy management data on PowerVM had an endian bug
leading to bogus results.
When reporting a machine check exception we incorrectly reported TLB multihits
as D-Cache multhits due to a missing entry in the array of causes.
Thanks to:
Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar, Segher Boessenkool,
Vaidyanathan Srinivasan.
-----BEGIN PGP SIGNATURE-----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=Ugv6
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three non-regression fixes.
- Our optimised memcmp could read past the end of one of the buffers
and potentially trigger a page fault leading to an oops.
- Some of our code to read energy management data on PowerVM had an
endian bug leading to bogus results.
- When reporting a machine check exception we incorrectly reported
TLB multihits as D-Cache multhits due to a missing entry in the
array of causes.
Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
Segher Boessenkool, Vaidyanathan Srinivasan"
* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries/mce: Fix misleading print for TLB mutlihit
powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
powerpc/64: Fix memcmp reading past the end of src/dest
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXJ+ymAAKCRBiEGxRG/Sl
2yIKAQCnxxzaaCfoXtnYnpgtSZApKX+ifpkImh1WOvly+HLE4QEA3i3Bg4pb23ck
fClCFU9sahuxJbakWD0pvs4k77I1GQY=
=5KCa
-----END PGP SIGNATURE-----
Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix refcnt leak on interface rename
- use memcpy in device_name_store() to avoid including garbage from a
previous, longer value in the device_name
- fix a potential NULL pointer dereference in case of_match_device()
cannot find a match
* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: trigger: netdev: use memcpy in device_name_store
leds: pca9532: fix a potential NULL pointer dereference
leds: trigger: netdev: fix refcnt leak on interface rename
- Revert the extended use of gpio_set_config() and think about
how we can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on
the SPI bus children, as intended.
- Error paths and driver fixes.
-----BEGIN PGP SIGNATURE-----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=6ndO
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"As you can see [in the git history] I was away on leave and Bartosz
kindly stepped in and collected a slew of fixes, I pulled them into my
tree in two sets and merged some two more fixes (fixing my own caused
bugs) on top.
Summary:
- Revert the extended use of gpio_set_config() and think about how we
can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on the SPI
bus children, as intended.
- Error paths and driver fixes"
* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mockup: use simple_read_from_buffer() in debugfs read callback
gpio: of: Fix of_gpiochip_add() error path
gpio: of: Check for "spi-cs-high" in child instead of parent node
gpio: of: Check propname before applying "cs-gpios" quirks
gpio: mockup: fix debugfs read
Revert "gpio: use new gpio_set_config() helper in more places"
gpio: aspeed: fix a potential NULL pointer dereference
gpio: amd-fch: Fix bogus SPDX identifier
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
gpio: exar: add a check for the return value of ida_simple_get fails
If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example
# cat device_name
# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32
I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.
This is also preparation for future patches.
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.
Fixes: fa4191a609 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ8vpg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksHgCeJATLFpgiWqGvR8K/PfiG2QixudEAoMivMAM2
s1Obj1TFIQK+xTAINt6U
=uJaK
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Remove vif check from vnt_interrupt
staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
staging: octeon-ethernet: fix incorrect PHY mode
staging: vc04_services: Fix an error code in vchiq_probe()
staging: erofs: fix error handling when failed to read compresssed data
staging: vt6655: Fix interrupt race condition on device start up.
staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
staging: rtl8712: uninitialized memory in read_bbreg_hdl()
staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
staging, mt7621-pci: fix build without pci support
staging: speakup_soft: Fix alternate speech with other synths
staging: axis-fifo: add CONFIG_OF dependency
staging: olpc_dcon_xo_1: add missing 'const' qualifier
staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
staging: erofs: fix to handle error path of erofs_vmap()
staging: mt7621-dts: update ethernet settings.
staging: remove mt7621-eth
Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for error
handling paths, as well as some other minor bugfixes for reported issues
with 5.1-rc1.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ8wCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylWigCfSPVnxuGsNFTZIN8CUMBH4I5cmjkAnjrN3NdS
Sumt55mskpi/Ht+5UWmw
=LFqo
-----END PGP SIGNATURE-----
Merge tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for
error handling paths, as well as some other minor bugfixes for
reported issues with 5.1-rc1.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix NULL pointer issue when tty_port ops is not set
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
dt-bindings: serial: Add compatible for Mediatek MT8183
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
tty/serial: atmel: Add is_half_duplex helper
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
serial: ar933x_uart: Fix build failure with disabled console
tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
tty: mxs-auart: fix a potential NULL pointer dereference
tty: atmel_serial: fix a potential NULL pointer dereference
serial: max310x: Fix to avoid potential NULL pointer dereference
serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
Here are some small USB fixes for 5.1-rc3.
Nothing major at all here, just a small collection of fixes for reported
issues, and potential problems with error handling paths. Also a few
new device ids, as normal.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ8wdQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn4iwCeJJST7rZyr/PO5lD8nm90y6WesawAn0WR2jEZ
TR6natKYdZq5SVfLo0y/
=MFul
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.1-rc3.
Nothing major at all here, just a small collection of fixes for
reported issues, and potential problems with error handling paths.
Also a few new device ids, as normal.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Olicard 600
USB: serial: cp210x: add new device id
usb: u132-hcd: fix resource leak
usb: cdc-acm: fix race during wakeup blocking TX traffic
usb: mtu3: fix EXTCON dependency
usb: usb251xb: fix to avoid potential NULL pointer dereference
usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
xhci: Don't let USB3 ports stuck in polling state prevent suspend
usb: xhci: dbc: Don't free all memory with spinlock held
xhci: Fix port resume done detection for SS ports with LPM enabled
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
USB: gadget: f_hid: fix deadlock in f_hidg_write()
usb: gadget: net2272: Fix net2272_dequeue()
usb: gadget: net2280: Fix net2280_dequeue()
usb: gadget: net2280: Fix overrun of OUT messages
usb: dwc3: pci: add support for Comet Lake PCH ID
usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
usb: common: Consider only available nodes for dr_mode
usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
...
Correct a previous attempt to make Linux use its own set of ACPI debug
flags different from the upstream ACPICA's default (Erik Schmauss).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ze64
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This corrects a previous attempt to make Linux use its own set of ACPI
debug flags different from the upstream ACPICA's default (Erik
Schmauss)"
* tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: use different default debug value than ACPICA
- Fix the ACPI CPPC library to actually follow the specification
when decoding the guaranteed performance register information and
make the intel_pstate driver to fall back to the nominal frequency
when reporting the base frequency if the guaranteed performance
register information is not there (Srinivas Pandruvada).
- Fix use-after-free in the exit callback of the scpi-cpufreq left
after an update during the 5.0 development cycle (Vincent Stehlé).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mhtx
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix CPU base frequency reporting in the intel_pstate driver and
a use-after-free in the scpi-cpufreq driver.
Specifics:
- Fix the ACPI CPPC library to actually follow the specification when
decoding the guaranteed performance register information and make
the intel_pstate driver to fall back to the nominal frequency when
reporting the base frequency if the guaranteed performance register
information is not there (Srinivas Pandruvada).
- Fix use-after-free in the exit callback of the scpi-cpufreq left
after an update during the 5.0 development cycle (Vincent Stehlé)"
* tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi: Fix use after free
cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
ACPI / CPPC: Fix guaranteed performance handling
Pull security layer fixes from James Morris:
"Yama and LSM config fixes"
* 'fixes-v5.1-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
LSM: Revive CONFIG_DEFAULT_SECURITY_* for "make oldconfig"
Yama: mark local symbols as static
Merge misc fixes from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
fs: fs_parser: fix printk format warning
checkpatch: add %pt as a valid vsprintf extension
mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
drivers/block/zram/zram_drv.c: fix idle/writeback string compare
mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
mm/memory_hotplug.c: fix notification in offline error path
ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK
fs/proc/kcore.c: make kcore_modules static
include/linux/list.h: fix list_is_first() kernel-doc
mm/debug.c: fix __dump_page when mapping->host is not set
mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
include/linux/hugetlb.h: convert to use vm_fault_t
iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
mm: add support for kmem caches in DMA32 zone
ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
mm/hotplug: fix offline undo_isolate_page_range()
fs/open.c: allow opening only regular files during execve()
mailmap: add Changbin Du
mm/debug.c: add a cast to u64 for atomic64_read()
...
request_standard_resources(), the latter being limited to the low 4G
memory range on arm64.
-----BEGIN PGP SIGNATURE-----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=c25Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Use memblock_alloc() instead of memblock_alloc_low() in
request_standard_resources(), the latter being limited to the low 4G
memory range on arm64"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: replace memblock_alloc_low with memblock_alloc
Including:
- Fix a bug in the AMD IOMMU driver not handling exclusion ranges
correctly. In fact the driver did not reserve these ranges for
IOVA allocations, so that dma-handles could be allocated in an
exclusion range, leading to data corruption. Exclusion ranges
have not been used by any firmware up to now, so this issue
remained undiscovered for quite some time.
- Fix wrong warning messages that the IOMMU core code prints
when it tries to allocate the default domain for an iommu
group and the driver does not support any of the default
domain types (like Intel VT-d).
-----BEGIN PGP SIGNATURE-----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=HY4V
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Fix a bug in the AMD IOMMU driver not handling exclusion ranges
correctly. In fact the driver did not reserve these ranges for IOVA
allocations, so that dma-handles could be allocated in an exclusion
range, leading to data corruption. Exclusion ranges have not been
used by any firmware up to now, so this issue remained undiscovered
for quite some time.
- Fix wrong warning messages that the IOMMU core code prints when it
tries to allocate the default domain for an iommu group and the
driver does not support any of the default domain types (like Intel
VT-d).
* tag 'iommu-fixes-v5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Reserve exclusion range in iova-domain
iommu: Don't print warning when IOMMU driver only supports unmanaged domains
Here is a single driver core patch for 5.1-rc3.
After 5.1-rc1, all of the users of BUS_ATTR() are finally removed, so we
can now drop this macro from include/linux/device.h so that no more new
users will be created.
This patch has been in linux-next for a while, with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ5skg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylp3wCfT73IbPPjeSxWZjyPLOBiz31YfTEAnjajShZl
gQk7H0O5Ovv5ntsyk0bM
=CRS4
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core patch for 5.1-rc3.
After 5.1-rc1, all of the users of BUS_ATTR() are finally removed, so
we can now drop this macro from include/linux/device.h so that no more
new users will be created.
This patch has been in linux-next for a while, with no reported
issues"
* tag 'driver-core-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: remove BUS_ATTR()
Here are some binder, habanalabs, and vboxguest driver fixes for
5.1-rc3.
The Binder fixes resolve some reported issues found by testing, first by
the selinux developers, and then earlier today by syzbot.
The habanalabs fixes are all minor, resolving a number of tiny things.
The vboxguest patches are a bit larger. They resolve the fact that
virtual box decided to change their api in their latest release in a way
that broke the existing kernel code, despite saying that they were never
going to do that. So this is a bit of a "new feature", but is good to
get merged so that 5.1 will work with the latest release. The changes
are not large and of course virtual box "swears" they will not break
this again, but no one is holding their breath here.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXJ50KA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGsgCgtDaSHl+qjalyC3SegP9s6fUfoXwAoKuKS2Ti
ROSQqZKSRNWvAqCwWUT4
=K3ll
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some binder, habanalabs, and vboxguest driver fixes for
5.1-rc3.
The Binder fixes resolve some reported issues found by testing, first
by the selinux developers, and then earlier today by syzbot.
The habanalabs fixes are all minor, resolving a number of tiny things.
The vboxguest patches are a bit larger. They resolve the fact that
virtual box decided to change their api in their latest release in a
way that broke the existing kernel code, despite saying that they were
never going to do that. So this is a bit of a "new feature", but is
good to get merged so that 5.1 will work with the latest release. The
changes are not large and of course virtual box "swears" they will not
break this again, but no one is holding their breath here.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
virt: vbox: Implement passing requestor info to the host for VirtualBox 6.0.x
binder: fix race between munmap() and direct reclaim
binder: fix BUG_ON found by selinux-testsuite
habanalabs: cast to expected type
habanalabs: prevent host crash during suspend/resume
habanalabs: perform accounting for active CS
habanalabs: fix mapping with page size bigger than 4KB
habanalabs: complete user context cleanup before hard reset
habanalabs: fix bug when mapping very large memory area
habanalabs: fix MMU number of pages calculation
13 Fixes, 7 of which are for IBM fibre channel and three additional
for fairly serious bugs in drivers (qla2xxx, mpt3sas, aacraid). Of
the three core fixes, the most significant is probably the missed run
queue causing an indefinite hang. The others are fixing a potential
use after free on device close and silencing an incorrect warning.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXJ5iYiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQ4GAP99uutL
UuDJ4pLfcl7N3PgUy1/HtvZ5CXcNGjK3Tu1V7wD9FJ/rC0EKSmc+s01/w51iSytt
/9QaDbK+R/RV6Rg/QJc=
=4AwN
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Thirteen fixes, seven of which are for IBM fibre channel and three
additional for fairly serious bugs in drivers (qla2xxx, mpt3sas,
aacraid).
Of the three core fixes, the most significant is probably the missed
run queue causing an indefinite hang. The others are fixing a
potential use after free on device close and silencing an incorrect
warning"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvfc: Clean up transport events
scsi: ibmvfc: Byte swap status and error codes when logging
scsi: ibmvfc: Add failed PRLI to cmd_status lookup array
scsi: ibmvfc: Remove "failed" from logged errors
scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN
scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
scsi: sd: Quiesce warning if device does not report optimal I/O size
scsi: sd: Fix a race between closing an sd device and sd I/O
scsi: core: Run queue when state is set to running after being blocked
scsi: qla4xxx: fix a potential NULL pointer dereference
scsi: aacraid: Insure we don't access PCIe space during AER/EEH
scsi: mpt3sas: Fix kernel panic during expander reset
Pull i2c fixes from Wolfram Sang:
"A new ID for the i801 driver and some Documentation fixes to make it
easier for people to find the bindings (which is also a basis for
further improvements in that area)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: wmt: make bindings file name match the driver
i2c: sun6i-p2wi: make bindings file name match the driver
i2c: stu300: make bindings file name match the driver
i2c: mt65xx: make bindings file name match the driver
i2c: iop3xx: make bindings file name match the driver
i2c: i801: Add support for Intel Comet Lake
The important fixes at this time are a couple fixes in ALSA core:
a fix for PCM is about the OOB access in PCM OSS plugins that has
been for long time, but hasn't hit so often until now just because
we allocated a large buffer via vmalloc(), and surfaced more often
after switching to kvmalloc(). Another fix is for a long-standing
PCM problem wrt racy PM resume. Others are trivial nospec coverage
and usual HD-audio quirks.
-----BEGIN PGP SIGNATURE-----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=R8s8
-----END PGP SIGNATURE-----
Merge tag 'sound-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The important fixes at this time are a couple fixes in ALSA core: a
fix for PCM is about the OOB access in PCM OSS plugins that has been
for long time, but hasn't hit so often until now just because we
allocated a large buffer via vmalloc(), and surfaced more often after
switching to kvmalloc(). Another fix is for a long-standing PCM
problem wrt racy PM resume.
Others are trivial nospec coverage and usual HD-audio quirks"
* tag 'sound-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix speakers on Acer Predator Helios 500 Ryzen laptops
ALSA: pcm: Don't suspend stream in unrecoverable PCM state
ALSA: hda/ca0132 - Simplify alt firmware loading code
ALSA: pcm: Fix possible OOB access in PCM oss plugins
ALSA: hda/realtek: Enable headset MIC of ASUS X430UN and X512DK with ALC256
ALSA: hda/realtek: Enable headset mic of ASUS P5440FF with ALC256
ALSA: hda/realtek: Enable ASUS X441MB and X705FD headset MIC with ALC256
ALSA: hda/realtek - Add support for Acer Aspire E5-523G/ES1-432 headset mic
ALSA: hda/realtek: Enable headset MIC of Acer Aspire Z24-890 with ALC286
ALSA: seq: oss: Fix Spectre v1 vulnerability
ALSA: rawmidi: Fix potential Spectre v1 vulnerability
- Remove harmful -Oz option of Clang
- Get back the original behavior (no recursion for in-tree build)
for GNU Make 4.x
- Some minor fixes for coccinelle patches
- Do not overwrite .gitignore in the output directory in case
it is version-controlled
- Fix missed record-mcount bug for dynamic ftrace
- Fix endianness bug in modversions for relative CRC
- Cater to '^H' key code in Kconfig ncurses programs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6tE2
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Remove harmful -Oz option of Clang
- Get back the original behavior (no recursion for in-tree build) for
GNU Make 4.x
- Some minor fixes for coccinelle patches
- Do not overwrite .gitignore in the output directory in case it is
version-controlled
- Fix missed record-mcount bug for dynamic ftrace
- Fix endianness bug in modversions for relative CRC
- Cater to '^H' key code in Kconfig ncurses programs
* tag 'kbuild-fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig/[mn]conf: handle backspace (^H) key
kbuild: modversions: Fix relative CRC byte order interpretation
scripts: coccinelle: Fix description of badty.cocci
kbuild: strip whitespace in cmd_record_mcount findstring
kbuild: do not overwrite .gitignore in output directory
kbuild: skip parsing pre sub-make code for recursion
coccinelle: put_device: reduce false positives
kbuild: skip sub-make for in-tree build with GNU Make 4.x
Revert "kbuild: use -Oz instead of -Os when using clang"
-----BEGIN PGP SIGNATURE-----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=3chO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190329' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Small set of fixes that should go into this series. This contains:
- compat signal mask fix for io_uring (Arnd)
- EAGAIN corner case for direct vs buffered writes for io_uring
(Roman)
- NVMe pull request from Christoph with various little fixes
- sbitmap ws_active fix, which caused a perf regression for shared
tags (me)
- sbitmap bit ordering fix (Ming)
- libata on-stack DMA fix (Raymond)"
* tag 'for-linus-20190329' of git://git.kernel.dk/linux-block:
nvmet: fix error flow during ns enable
nvmet: fix building bvec from sg list
nvme-multipath: relax ANA state check
nvme-tcp: fix an endianess miss-annotation
libata: fix using DMA buffers on stack
io_uring: offload write to async worker in case of -EAGAIN
sbitmap: order READ/WRITE freed instance and setting clear bit
blk-mq: fix sbitmap ws_active for shared tags
io_uring: fix big-endian compat signal mask handling
blk-mq: update comment for blk_mq_hctx_has_pending()
blk-mq: use blk_mq_put_driver_tag() to put tag
a small use-after-free fix.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlyeRsgTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi8i6B/9wP90ZLGzdAZDIlfWKXjGB1PUrFdeN
WCA5p68Hl7yh1RbY6cvbZcTF5Bo3DhjxjxTFjXHPXLxsARlxbCXon9R6Lo2lDgA4
Bk/W8dcR3onU3nspifG91Him/WnImWB80pyVgZog2PTiwsZJ0rRknXXbRU9ARCpk
8vjg19O4wHwXgtMXAN3vxjQ7v8T8wk8vDb08efPcmMPLDYMaTUL1z2JoqyRfMTbo
OpZoXSjHXqVFfz0mJ5EN7+92eK39oDcQIDSuuqePDCI09ZmrcQd/xSvG5tBfPoXr
1mR3ojkKRURW5RKGClbSoAt90vIuYJH5Cncmemzsr6m4FETH6XthGbJl
=twzl
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.1-rc3' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to avoid choking on multipage bvecs in the messenger and a
small use-after-free fix"
* tag 'ceph-for-5.1-rc3' of git://github.com/ceph/ceph-client:
ceph: fix use-after-free on symlink traversal
libceph: fix breakage caused by multipage bvecs
- Fix a bunch of static checker complaints about uninitialized variables
and insufficient range checks.
- Avoid a crash when incore extent map data are corrupt.
- Disallow FITRIM when we haven't recovered the log and know the
metadata are stale.
- Fix a data corruption when doing unaligned overlapping dio writes.
-----BEGIN PGP SIGNATURE-----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=iNqS
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.1-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are a few fixes for some corruption bugs and uninitialized
variable problems. The few patches here have gone through a few days
worth of fstest runs with no new problems observed.
Changes since last update:
- Fix a bunch of static checker complaints about uninitialized
variables and insufficient range checks.
- Avoid a crash when incore extent map data are corrupt.
- Disallow FITRIM when we haven't recovered the log and know the
metadata are stale.
- Fix a data corruption when doing unaligned overlapping dio writes"
* tag 'xfs-5.1-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: serialize unaligned dio writes against all other dio writes
xfs: prohibit fstrim in norecovery mode
xfs: always init bma in xfs_bmapi_write
xfs: fix btree scrub checking with regards to root-in-inode
xfs: dabtree scrub needs to range-check level
xfs: don't trip over uninitialized buffer on extent read of corrupted inode
Commit 70b62c2566 ("LoadPin: Initialize as ordered LSM") removed
CONFIG_DEFAULT_SECURITY_{SELINUX,SMACK,TOMOYO,APPARMOR,DAC} from
security/Kconfig and changed CONFIG_LSM to provide a fixed ordering as a
default value. That commit expected that existing users (upgrading from
Linux 5.0 and earlier) will edit CONFIG_LSM value in accordance with
their CONFIG_DEFAULT_SECURITY_* choice in their old kernel configs. But
since users might forget to edit CONFIG_LSM value, this patch revives
the choice (only for providing the default value for CONFIG_LSM) in order
to make sure that CONFIG_LSM reflects CONFIG_DEFAULT_SECURITY_* from their
old kernel configs.
Note that since TOMOYO can be fully stacked against the other legacy
major LSMs, when it is selected, it explicitly disables the other LSMs
to avoid them also initializing since TOMOYO does not expect this
currently.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 70b62c2566 ("LoadPin: Initialize as ordered LSM")
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Core libraries:
Jiri Olsa:
- Fix max perf_event_attr.precise_ip detection.
Kan Liang:
- Fix parser error for uncore event alias
Wei Lin:
- Fixup ordering of kernel maps after obtaining the main kernel map address.
Intel PT:
Adrian Hunter:
- Fix TSC slip where A TSC packet can slip past MTC packets so that the
timestamp appears to go backwards.
- Fixes for exported-sql-viewer GUI conversion to python3.
ARM coresight:
Solomon Tan:
- Fix the build by adding a missing case value for enumeration value introduced
in newer library, that now is the required one.
tool headers:
Arnaldo Carvalho de Melo:
- Syncronize kernel headers with the kernel, getting new io_uring and
pidfd_send_signal syscalls so that 'perf trace' can handle them.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXJ4eoQAKCRCyPKLppCJ+
J2HgAP9QsIB6UlfcsNtttJa2b5yMEcOvfA6xfr37Ihu9uWin1gEAhDbbb7MW5fNv
0fjY7Q7YvfiwRWvVpr32BW//5FKnaQI=
=j989
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-5.1-20190329' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo:
Core libraries:
Jiri Olsa:
- Fix max perf_event_attr.precise_ip detection.
Kan Liang:
- Fix parser error for uncore event alias
Wei Lin:
- Fixup ordering of kernel maps after obtaining the main kernel map address.
Intel PT:
Adrian Hunter:
- Fix TSC slip where A TSC packet can slip past MTC packets so that the
timestamp appears to go backwards.
- Fixes for exported-sql-viewer GUI conversion to python3.
ARM coresight:
Solomon Tan:
- Fix the build by adding a missing case value for enumeration value introduced
in newer library, that now is the required one.
tool headers:
Arnaldo Carvalho de Melo:
- Syncronize kernel headers with the kernel, getting new io_uring and
pidfd_send_signal syscalls so that 'perf trace' can handle them.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcnZWiAAoJEAx081l5xIa+0SEQAIECjILAICp/h0CitVe09fvU
NB1TimOsJwjhbJSHdUX4l/FqHRz6xczxnW3yDjteOdg5a/LLtyI+C0ZBaF/RYVK5
dXk8xNiu3Hoem/+W2shfLjTKKjxSp6Hul4Mx8BL/svClo33K76VuMrcoOAhrYq4G
dVbjB6iTSkT8IiYUsNfcddKj2S7rpObAoPindPavHqye2yzGrCDuRmYy5gxszpHs
IcKN+6f0voT0caijiXRDwQ/F97f6YghKVTizXsuwbbFa5wQuvNlZhCdT6ltORoab
n05/VA8diP+ttu85d+HGlUKtUcB01nkVqr4qAPOHq44CmLbsJKs+wp1zMN88xInT
koMR/ElG1DmwXQgbrNI7hrcJsh6N0DB9MUG2gGrz+Sa46aAYweb1c6YVdseR3o4x
cisMhIzxJ0IVlBI5fV7qxZrUrhzYzqtX7sBosVDiszs92EU8MvCcqMjIwXmOZexE
du6Exxq61Cx4xvBJIPTDWFvNHZVq9xKepCzgxmeKJmYx5yTZiS+hXJ5G+PL+JVri
I1O9esPfbXeW9Y7j/sm/pe3udoha9D6sg0/hnPNpUCGx0P7d/DhiIyUF7zEy+/CN
N3xKWxslpbwfNg6bbscxE01ToLGz/TX+R2ANcAmLQeWPFfs3CIfJzs9flncMvi8A
9reKUm+OZBeJ9q0nEYdb
=6CNL
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-03-29' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Weekly fixes roundup, nothing two serious, some usb device regressions
are fixed, and i915 GVT has a bigger fix but otherwise not really much
happening here.
core:
- fb bpp check regression fix
- release/unplug fix
- use after free fixes
i915:
- fix mmap range checks
- fix gvt ppgtt mm LRU list access races
- fix selftest error pointer check
- fix a macro definition (pre-emptive for potential further backports)
- fix one AML SKU ULX status
amdgpu:
- one variable refresh rate fix
udl:
- fix EDID reading
tegra:
- build/warning fixes
meson:
- cleanup path fixes
- TMDS clock filter fix
rockchip:
- NV12 buffers and scalar fix"
* tag 'drm-fixes-2019-03-29' of git://anongit.freedesktop.org/drm/drm: (22 commits)
drm/i915/icl: Fix VEBOX mismatch BUG_ON()
drm/i915/selftests: Fix an IS_ERR() vs NULL check
drm/i915: Mark AML 0x87CA as ULX
drm/meson: fix TMDS clock filtering for DMT monitors
drm/meson: Uninstall IRQ handler
drm/meson: Fix invalid pointer in meson_drv_unbind()
drm/udl: Refactor edid retrieving in UDL driver (v2)
drm: Fix drm_release() and device unplug
drm/fb: avoid setting 0 depth.
drm/tegra: vic: Fix implicit function declaration warning
drm/tegra: hub: Fix dereference before check
drm/i915/icl: Fix the TRANS_DDI_FUNC_CTL2 bitfield macro
drm/amd/display: Only allow VRR when vrefresh is within supported range
drm/rockchip: vop: reset scale mode when win is disabled
drm/vkms: fix use-after-free when drm_gem_handle_create() fails
drm/vgem: fix use-after-free when drm_gem_handle_create() fails
drm/i915/gvt: Add mutual lock for ppgtt mm LRU list
drm/i915/gvt: Only assign ppgtt root at dispatch time
drm/i915/gvt: Don't submit request for error workload dispatch
drm/i915/gvt: stop scheduling workload when vgpu is inactive
...
Greg Kroah-Hartman