Add a new attribute NLMSGERR_ATTR_POLICY to the extended ACK
to advertise the policy, e.g. if an attribute was out of range,
you'll know the range that's permissible.
Add new NL_SET_ERR_MSG_ATTR_POL() and NL_SET_ERR_MSG_ATTR_POL()
macros to set this, since realistically it's only useful to do
this when the bad attribute (offset) is also returned.
Use it in lib/nlattr.c which practically does all the policy
validation.
v2:
- add and use netlink_policy_dump_attr_size_estimate()
v3:
- remove redundant break
v4:
- really remove redundant break ... sorry
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't have good validation policy for existing unsigned int attrs
which serve as flags (for new ones we could use NLA_BITFIELD32).
With increased use of policy dumping having the validation be
expressed as part of the policy is important. Add validation
policy in form of a mask of supported/valid bits.
Support u64 in the uAPI to be future-proof, but really for now
the embedded mask member can only hold 32 bits, so anything with
bit 32+ set will always fail validation.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The need for padding 64bit is implicitly checked by nla_align_64bit(), so
remove this explicit one.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add range validation for NLA_BINARY, allowing validation of any
combination of combination minimum or maximum lengths, using the
existing NLA_POLICY_RANGE()/NLA_POLICY_FULL_RANGE() macros, just
like for integers where the value is checked.
Also make NLA_POLICY_EXACT_LEN(), NLA_POLICY_EXACT_LEN_WARN()
and NLA_POLICY_MIN_LEN() special cases of this, removing the old
types NLA_EXACT_LEN and NLA_MIN_LEN.
This allows us to save some code where both minimum and maximum
lengths are requires, currently the policy only allows maximum
(NLA_BINARY), minimum (NLA_MIN_LEN) or exact (NLA_EXACT_LEN), so
a range of lengths cannot be accepted and must be checked by the
code that consumes the attributes later.
Also, this allows advertising the correct ranges in the policy
export to userspace. Here, NLA_MIN_LEN and NLA_EXACT_LEN already
were special cases of NLA_BINARY with min and min/max length
respectively.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to get the policy's signed/unsigned range
validation data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NLA_MSECS is really equivalent to NLA_U64, allow
it to have range validation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a pointer to a struct indicating the min/max values,
extend the ability to do range validation for arbitrary
values. Small values in the s16 range can be kept in the
policy directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have nested policies, we can theoretically
recurse forever parsing attributes if a (sub-)policy
refers back to a higher level one. This is a situation
that has happened in nl80211, and we've avoided it there
by not linking it.
Add some code to netlink parsing to limit recursion depth.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the netlink policy, we currently have a void *validation_data
that's pointing to different things:
* a u32 value for bitfield32,
* the netlink policy for nested/nested array
* the string for NLA_REJECT
Remove the pointer and place appropriate type-safe items in the
union instead.
While at it, completely dissolve the pointer for the bitfield32
case and just put the value there directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that attribute type is within 0...maxtype range in
__nla_validate_parse() sets only error message but not bad_attr in extack.
Set also bad_attr to tell userspace which attribute failed validation.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, we cannot add strict parsing for all attributes, as
that would break existing userspace. We currently warn about it, but
that's about all we can do.
For new attributes, however, the story is better: nobody is using
them, so we can reject bad sizes.
Also, for new attributes, we need not accept them when the policy
doesn't declare their usage.
David Ahern and I went back and forth on how to best encode this, and
the best way we found was to have a "boundary type", from which point
on new attributes have all possible validation applied, and NLA_UNSPEC
is rejected.
As we didn't want to add another argument to all functions that get a
netlink policy, the workaround is to encode that boundary in the first
entry of the policy array (which is for type 0 and thus probably not
really valid anyway). I put it into the validation union for the rare
possibility that somebody is actually using attribute 0, which would
continue to work fine unless they tried to use the extended validation,
which isn't likely. We also didn't find any in-tree users with type 0.
The reason for setting the "start strict here" attribute is that we
never really need to start strict from 0, which is invalid anyway (or
in legacy families where that isn't true, it cannot be set to strict),
so we can thus reserve the value 0 for "don't do this check" and don't
have to add the tag to all policies right now.
Thus, policies can now opt in to this validation, which we should do
for all existing policies, at least when adding new attributes.
Note that entirely *new* policies won't need to set it, as the use
of that should be using nla_parse()/nlmsg_parse() etc. which anyway
do fully strict validation now, regardless of this.
So in effect, this patch only covers the "existing command with new
attribute" case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using NLA_UNSPEC for this type of thing, use NLA_MIN_LEN
so we can make NLA_UNSPEC be NLA_REJECT under certain conditions for
future attributes.
While at it, also use NLA_EXACT_LEN for the struct example.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_parse is currently lenient on message parsing, allowing type to be 0
or greater than max expected and only logging a message
"netlink: %d bytes leftover after parsing attributes in process `%s'."
if the netlink message has unknown data at the end after parsing. What this
could mean is that the header at the front of the attributes is actually
wrong and the parsing is shifted from what is expected.
Add a new strict version that actually fails with EINVAL if there are any
bytes remaining after the parsing loop completes, if the atttrbitue type
is 0 or greater than max expected.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to have an arbitrary validation function attached
to a netlink policy that doesn't already use the validation_data
pointer in another way.
This can be useful to validate for example the content of a binary
attribute, like in nl80211 the "(information) elements", which must
be valid streams of "u8 type, u8 length, u8 value[length]".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without further bloating the policy structs, we can overload
the `validation_data' pointer with a struct of s16 min, max
and use those to validate ranges in NLA_{U,S}{8,16,32,64}
attributes.
It may sound strange to validate NLA_U32 with a s16 max, but
in many cases NLA_U32 is used for enums etc. since there's no
size benefit in using a smaller attribute width anyway, due
to netlink attribute alignment; in cases like that it's still
useful, particularly when the attribute really transports an
enum value.
Doing so lets us remove quite a bit of validation code, if we
can be sure that these attributes aren't used by userspace in
places where they're ignored today.
To achieve all this, split the 'type' field and introduce a
new 'validation_type' field which indicates what further
validation (beyond the validation prescribed by the type of
the attribute) is done. This currently allows for no further
validation (the default), as well as min, max and range checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes nested netlink attributes are just used as arrays, with
the nla_type() of each not being used; we have this in nl80211 and
e.g. NFTA_SET_ELEM_LIST_ELEMENTS.
Add the ability to validate this type of message directly in the
policy, by adding the type NLA_NESTED_ARRAY which does exactly
this: require a first level of nesting but ignore the attribute
type, and then inside each require a second level of nested and
validate those attributes against a given policy (if present).
Note that some nested array types actually require that all of
the entries have the same index, this is possible to express in
a nested policy already, apart from the validation that only the
one allowed type is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a validation_data pointer, and the len field in
the policy is unused for NLA_NESTED, we can allow using them both
to have nested validation. This can be nice in code, although we
still have to use nla_parse_nested() or similar which would also
take a policy; however, it also serves as documentation in the
policy without requiring a look at the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the code between nla_parse() which sets the bad
attribute pointer and an error message, and nla_validate()
which only sets the bad attribute pointer.
It also cleans up the code for NLA_REJECT and paves the way
for nested policy validation, as it will allow us to easily
skip setting the "generic" message without any extra args
like the **error_msg now, just passing the extack through is
now enough.
While at it, remove the unnecessary label in nla_parse().
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The validation data is only used within the policy that
should usually already be const, and isn't changed in any
code that uses it. Therefore, make the validation_data
pointer const.
While at it, remove the duplicate variable in the bitfield
validation that I'd otherwise have to change to const.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This isn't used anywhere, so we might as well get rid of it.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commonly, ethernet addresses are just using a policy of
{ .len = ETH_ALEN }
which leaves userspace free to send more data than it should,
which may hide bugs.
Introduce NLA_EXACT_LEN which checks for exact size, rejecting
the attribute if it's not exactly that length. Also add
NLA_EXACT_LEN_WARN which requires the minimum length and will
warn on longer attributes, for backward compatibility.
Use these to define NLA_POLICY_ETH_ADDR (new strict policy) and
NLA_POLICY_ETH_ADDR_COMPAT (compatible policy with warning);
these are used like this:
static const struct nla_policy <name>[...] = {
[NL_ATTR_NAME] = NLA_POLICY_ETH_ADDR,
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations some netlink attributes may be used for output
only (kernel->userspace) or may be reserved for future use. It's
then helpful to be able to prevent userspace from using them in
messages sent to the kernel, since they'd otherwise be ignored and
any future will become impossible if this happens.
Add NLA_REJECT to the policy which does nothing but reject (with
EINVAL) validation of any messages containing this attribute.
Allow for returning a specific extended ACK error message in the
validation_data pointer.
While at it clear up the documentation a bit - the NLA_BITFIELD32
documentation was added to the list of len field descriptions.
Also, use NL_SET_BAD_ATTR() in one place where it's open-coded.
The specific case I have in mind now is a shared nested attribute
containing request/response data, and it would be pointless and
potentially confusing to have userspace include response data in
the messages that actually contain a request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have one extack message for parsing and validating.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 28033ae4e0 ("net: netlink: Update attr validation to require
exact length for some types") requires attributes using types NLA_U* and
NLA_S* to have an exact length. This change is exposing bugs in various
userspace commands that are sending attributes with an invalid length
(e.g., attribute has type NLA_U8 and userspace sends NLA_U32). While
the commands are clearly broken and need to be fixed, users are arguing
that the sudden change in enforcement is breaking older commands on
newer kernels for use cases that otherwise "worked".
Relax the validation to print a warning mesage similar to what is done
for messages containing extra bytes after parsing.
Fixes: 28033ae4e0 ("net: netlink: Update attr validation to require exact length for some types")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attributes using NLA_U* and NLA_S* (where * is 8, 16,32 and 64) are
expected to be an exact length. Split these data types from
nla_attr_minlen into nla_attr_len and update validate_nla to require
the attribute to have exact length for them.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to strdup() for netlink string attributes.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Generic bitflags attribute content sent to the kernel by user.
With this netlink attr type the user can either set or unset a
flag in the kernel.
The value is a bitmap that defines the bit values being set
The selector is a bitmask that defines which value bit is to be
considered.
A check is made to ensure the rules that a kernel subsystem always
conforms to bitflags the kernel already knows about. i.e
if the user tries to set a bit flag that is not understood then
the _it will be rejected_.
In the most basic form, the user specifies the attribute policy as:
[ATTR_GOO] = { .type = NLA_BITFIELD32, .validation_data = &myvalidflags },
where myvalidflags is the bit mask of the flags the kernel understands.
If the user _does not_ provide myvalidflags then the attribute will
also be rejected.
Examples:
value = 0x0, and selector = 0x1
implies we are selecting bit 1 and we want to set its value to 0.
value = 0x2, and selector = 0x2
implies we are selecting bit 2 and we want to set its value to 1.
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Length of a netlink attribute may be u16 but lengths of basic attributes
are much smaller, so small we can save 16 bytes of .rodata and pocket
change inside .text.
16-bit is worse on x86-64 than 8-bit because of operand size override prefix.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-19 (-19)
function old new delta
validate_nla 418 417 -1
nla_policy_len 66 64 -2
nla_attr_minlen 32 16 -16
Total: Before=154865051, After=154865032, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo and describe 'padattr'.
Fixes: 089bf1a6a9 ("libnl: add more helpers to align attributes on 64-bit")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially important in cases where the kernel allocs a new
structure and expects a field to be set from a netlink attribute. If such
attribute is shorter than expected, the rest of the field is left containing
previous data. When such field is read back by the user space, kernel memory
content is leaked.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlattr.c doesn't seem to rely on anything from netdevice.h. Removing it
yields identical objdump -d output for each of {allyes,allno,def}config,
and eliminates more than 200 lines from the generated dependency file.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Fix some checkpatch warnings:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Pablo Neira <pablo@netfilter.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Any process is able to send netlink messages with leftover bytes.
Make the warning rate-limited to prevent too much log spam.
The warning is supposed to help find userspace bugs, so print the
triggering command name to implicate the buggy program.
[v2: Use pr_warn_ratelimited instead of printk_ratelimited.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_strcmp compares the string length plus one, so it's implicitly
including the nul-termination in the comparison.
int nla_strcmp(const struct nlattr *nla, const char *str)
{
int len = strlen(str) + 1;
...
d = memcmp(nla_data(nla), str, len);
However, if NLA_STRING is used, userspace can send us a string without
the nul-termination. This is a problem since the string
comparison will not match as the last byte may be not the
nul-termination.
Fix this by skipping the comparison of the nul-termination if the
attribute data is nul-terminated. Suggested by Thomas Graf.
Cc: Florian Westphal <fw@strlen.de>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For files only using THIS_MODULE and/or EXPORT_SYMBOL, map
them onto including export.h -- or if the file isn't even
using those, then just delete the include. Fix up any implicit
include dependencies that were being masked by module.h along
the way.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
L2TP for example uses NLA_MSECS like this:
policy:
[L2TP_ATTR_RECV_TIMEOUT] = { .type = NLA_MSECS, },
code:
if (info->attrs[L2TP_ATTR_RECV_TIMEOUT])
cfg.reorder_timeout = nla_get_msecs(info->attrs[L2TP_ATTR_RECV_TIMEOUT]);
As nla_get_msecs() is essentially nla_get_u64() plus the
conversion to a HZ-based value, this will not properly
reject attributes from userspace that aren't long enough
and might overrun the message.
Add NLA_MSECS to the attribute minlen array to check the
size properly.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently nla_policy_len always returns n * NLA_HDRLEN:
It loops, but does not advance it's iterator.
NLA_UNSPEC == 0 does not contain a .len in any policy.
Trivially fixed by adding p++.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg