In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210528202327.GA39994@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few leading spaces before tabs and remove it by running the
following commard:
$ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/'
$ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove own module name definition and use KBUILD_MODNAME instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the user changes the pause settings, the default settings
will be restored after an interface down/up cycle, and also when
resuming from suspend. This doesn't seem to provide the best user
experience. Change this to keep user settings, and just ensure that in
jumbo mode pause is disabled.
Small drawback: When switching back mtu from jumbo to non-jumbo then
pause remains disabled (but user can enable it using ethtool).
I think that's a not too common scenario and acceptable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc7 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new mac_managed_pm flag to indicate that the driver takes care
of PHY power management.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the N2100, instead of just marking the r8169 chips as having
broken_parity_status, disable parity error reporting for them entirely.
This was the only relevant place that set broken_parity_status, so we no
longer need to check for it in the r8169 error interrupt handler.
[bhelgaas: squash into one patch, commit log]
Link: https://lore.kernel.org/r/20210330174318.1289680-4-helgaas@kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
We can simply use rtl_hw_start_8168c_2() also for chip version 21.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool get_ringparam operation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOMMU errors have been reported if WoL is enabled and interface is
brought down. It turned out that the network chip triggers DMA
transfers after the DMA buffers have been freed. For WoL to work we
need to leave rx enabled, therefore simply stop the chip from being
a DMA busmaster.
Fixes: 567ca57faa ("r8169: add rtl8169_up")
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the lower_32_bits/upper_32_bits macros to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (0xBAF70000 & 0x00FFF000) << 6 should be (0xf70 << 18).
Fixes: 561535b0f2 ("r8169: fix OCP access on RTL8117")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macro pm_ptr(), this helps to avoid some ifdeffery.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaning up tx descriptors first increases the chance that
rtl_rx() can allocate new skb's from the cache.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in trying to disable interrupts if NAPI is
scheduled already. This allows us to save a PCI write in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/78c7f2fb-9772-1015-8c1d-632cbdff253f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the vendor driver, the new chip with XID 0x54b is
essentially the same as the one with XID 0x54a, but it doesn't need the
firmware.
So add support accordingly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210202044813.1304266-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far phy_disconnect() is called before free_irq(). If CONFIG_DEBUG_SHIRQ
is set and interrupt is shared, then free_irq() creates an "artificial"
interrupt by calling the interrupt handler. The "link change" flag is set
in the interrupt status register, causing phylib to eventually call
phy_suspend(). Because the net_device is detached from the PHY already,
the PHY driver can't recognize that WoL is configured and powers down the
PHY.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/fe732c2c-a473-9088-3974-df83cfbd6efd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was reported that on RTL8125 network breaks under heavy UDP load,
e.g. torrent traffic ([0], from comment 27). Realtek confirmed a hw bug
and provided me with a test version of the r8125 driver including a
workaround. Tests confirmed that the workaround fixes the issue.
I modified the original version of the workaround to meet mainline
code style.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=209839
v2:
- rebased to net
v3:
- make rtl_skb_is_udp() more robust and use skb_header_pointer()
to access the ip(v6) header
v4:
- remove dependency on ptp_classify.h
- replace magic number with offsetof(struct udphdr, len)
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Tested-by: xplo <xplo.bn@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/6e453d49-1801-e6de-d5f7-d7e6c7526c8f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtl_wol_enable_rx() is called via the following call chain if WoL
is enabled:
rtl8169_down()
-> rtl_prepare_power_down()
-> rtl_wol_enable_rx()
Therefore we don't have to call this function here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/34ce78e2-596c-e2ac-16aa-c550fa624c22@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of doing the full DASH check each time r8168_check_dash() is
called, let's do it once in probe and store DASH capabilities in a
new rtl8169_private member.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the mask to include the checksum failure bits. This allows to
simplify the condition in rtl8169_rx_csum().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At least from chip version 25 the vendor driver sets these rx flags
for all chip versions if WOL is enabled. Therefore I wouldn't consider
it a quirk, so let's rename the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean up the remainings of rtl_pll_power_down/up and rename
rtl_pll_power_down() to rtl_prepare_power_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek provided a description of bits 6 and 7 in register PMCH.
They configure whether the chip powers down certain PLL in D3hot and
D3cold respectively. They do not actually power down the PLL.
Reflect this in the code and configure D3 PLL powerdown based on
whether WOL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no known reason why PLL powerdown on D3 shouldn't be enabled
on chip versions 34, 35, 36, and 42. At least the vendor driver doesn't
exclude any of these chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we don't increase the max read request size if we switch to
jumbo mode before bringing up the interface for the first time.
Let's change this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Align behavior with r8168 vendor driver and don't reduce max read
request size for RTL8168e in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8168dp is ancient anyway, and I haven't seen any trace of its early
version 27 yet. This chip versions needs quite some special handling,
therefore it would facilitate driver maintenance if support for it
could be dropped. For now just disable detection of this chip version.
If nobody complains we can remove support for it in the near future.
v2:
- extend unknown chip version error message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ca98f018-a0e1-8762-e95c-f0ad773a0271@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If WOL isn't enabled, then there's no need to enable wakeup from D3
on system shutdown.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN_ONCE here to get a call trace in case of a problem.
This facilitates finding the offending code part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN here to avoid stopping the system. In addition print the addr
and mask values that triggered the warning.
v2:
- return on WARN to avoid an invalid register write
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to Realtek the ERI register 0x1a8 quirk is needed to work
around a hw issue with the PHY on RTL8168g. The register needs to be
changed before powering down the PHY. Currently we don't meet this
requirement, however I'm not aware of any problems caused by this.
Therefore I see the change as an improvement.
The PHY driver has no means to access the chip ERI registers,
therefore we have to intercept MDIO writes to BMCR register.
If the BMCR_PDOWN bit is going to be set, then let's apply the
quirk before actually powering down the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No functional change here. We just move a code block to avoid a
function forward declaration in a subsequent change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A user reported failing network with RTL8168dp (a quite rare chip
version). Realtek confirmed that few chip versions suffer from a PLL
power-down hw bug.
Fixes: 07df5bd874 ("r8169: power down chip in probe")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a1c39460-d533-7f9e-fa9d-2b8990b02426@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent changes there's no need any longer to define NUM_RX_DESC
as an unsigned value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to check min(budget, NUM_RX_DESC). At first budget
(NAPI_POLL_WEIGHT = 64) is less then NUM_RX_DESC (256).
And more important: Even in case of budget > NUM_RX_DESC we could
safely continue processing descriptors as long as they are owned by
the CPU. In addition replace rx_left with a normal counter variable,
this allows to simplify the code. Last but not least there's no need
any longer to pass the budget as an u32.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>