This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY will delay about 11.5ms to generate RXC clock when switching from
power down to normal operation. Read/write registers would also cause RXC
become unstable and stop for a while during this process. Realtek engineer
suggests 15ms or more delay can workaround this issue.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If enable Advance Link Down Power Saving (ALDPS) mode, it will change
crystal/clock behavior, which cause RXC clock stop for dozens to hundreds
of miliseconds. This is comfirmed by Realtek engineer. For some MACs, it
needs RXC clock to support RX logic, after this patch, PHY can generate
continuous RXC clock during auto-negotiation.
ALDPS default is disabled after hardware reset, it's more reasonable to
add a property to enable this feature, since ALDPS would introduce side effect.
This patch adds dt property "realtek,aldps-enable" to enable ALDPS mode
per users' requirement.
Jisheng Zhang enables this feature, changes the default behavior. Since
mine patch breaks the rule that new implementation should not break
existing design, so Cc'ed let him know to see if it can be accepted.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLKOUT is enabled by default after PHY hardware reset, this patch adds
"realtek,clkout-disable" property for user to disable CLKOUT clock
to save PHY power.
Per RTL8211F guide, a PHY reset should be issued after setting these
bits in PHYCR2 register. After this patch, CLKOUT clock output to be
disabled.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BAREUDP config option uses spaces instead of tabs for indentation.
The rest of this file uses tabs. Fix this.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new recycling API for page_pool.
In a drop rate test, the packet rate increased by 10%,
from 296 Kpps to 326 Kpps.
perf top on a stock system shows:
Overhead Shared Object Symbol
23.66% [kernel] [k] __pi___inval_dcache_area
22.85% [mvneta] [k] mvneta_rx_swbm
7.54% [kernel] [k] kmem_cache_alloc
6.49% [kernel] [k] eth_type_trans
3.94% [kernel] [k] dev_gro_receive
3.91% [kernel] [k] __netif_receive_skb_core
3.91% [kernel] [k] kmem_cache_free
3.76% [kernel] [k] page_pool_release_page
3.56% [kernel] [k] free_unref_page
2.40% [kernel] [k] build_skb
1.49% [kernel] [k] skb_release_data
1.45% [kernel] [k] __alloc_pages_bulk
1.30% [kernel] [k] page_frag_free
And this is the same output with recycling enabled:
Overhead Shared Object Symbol
26.41% [kernel] [k] __pi___inval_dcache_area
25.00% [mvneta] [k] mvneta_rx_swbm
8.14% [kernel] [k] kmem_cache_alloc
6.84% [kernel] [k] eth_type_trans
4.44% [kernel] [k] __netif_receive_skb_core
4.38% [kernel] [k] kmem_cache_free
4.16% [kernel] [k] dev_gro_receive
3.21% [kernel] [k] page_pool_put_page
2.41% [kernel] [k] build_skb
1.82% [kernel] [k] skb_release_data
1.61% [kernel] [k] napi_gro_receive
1.25% [kernel] [k] page_pool_refill_alloc_cache
1.16% [kernel] [k] __netif_receive_skb_list_core
We can see that page_pool_release_page(), free_unref_page() and
__alloc_pages_bulk() are no longer on top of the list when receiving
traffic.
The test was done with mausezahn on the TX side with 64 byte raw
ethernet frames.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prerequisite patch, the next one is enabling recycling of
skbs and fragments. Add an extra argument on __skb_frag_unref() to
handle recycling, and update the current users of the function with that.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function 'pnic2_lnk_change' is declared twice, so remove the
repeated declaration.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier patches have decoupled the MSI-X conveyed error handling
and recovery logic. This earlier concept code is no longer required.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling & recovery is done in context of reset task which
gets scheduled from misc interrupt handler in existing code. But
since error handling has been moved to new task, it should get
scheduled instead of the reset task from the interrupt handler.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling and recovery logic are intertwined. Error handling (i.e.
error identification, clearing error sources and initiation of recovery)
is done in context of reset task. If certain hardware errors get
delivered during driver init time, which can cause driver init/loading
to fail.
Introduce a separate error handling task to ensure below:
1. Reset logic remains independent of the error handling logic.
2. Add the hclge_errhand_task_schedule to schedule error recovery
tasks, This will ensure that common misellaneous MSI-X interrupt are
re-enabled quickly.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the following includecheck warning:
./drivers/net/ethernet/qlogic/qed/qed_nvmetcp_fw_funcs.h: linux/kernel.h
is included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
unbind() is the proper place to disconnect PHY, but it will fail if
netdev is already unregistered.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case phy_state_machine() works on top of USB device, we can get -ENODEV
at any point. So, be less noisy if device was removed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This usb devices can be removed at any time, so we need to forward
correct error value if device was detached.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With working phylib support we are able now to use generic selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to use ax88772 with external PHYs and use advantage of
existing PHY drivers, we need to port at least ax88772 part of asix
driver to the phylib framework.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for build-in x88772A/C PHYs
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor asix_read_phy_addr() to return usable error value directly and
make sure all callers handle this error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make resource management easier, use devm_kzalloc().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not directly BUG() when there is hdr error, it is
better to output a print when such error happens. Currently,
the caller of xmit_skb() already did it.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add space required before the open parenthesis '('.
Add space required after that close brace '}'.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant parentheses around 'cda >= desc_off'.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block comments use * on subsequent lines.
Block comments use a trailing */ on a separate line.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Braces {} should be used on all arms of this statement.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trailing statements should be on next line.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the checkpatch error as "foo* bar" and should be "foo *bar",
and "(foo*)" should be "(foo *)".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that both RevMII as well as RevRMII exist, we can deprecate the
sja1105,role-mac and sja1105,role-phy properties and simply let the user
select that a port operates in MII PHY role by using
phy-mode = "rev-mii";
or in RMII PHY role by using
phy-mode = "rev-rmii";
There are no fixed-link MII or RMII properties in mainline device trees,
and the setup itself is fairly uncommon, so there shouldn't be risks of
breaking compatibility.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has an intermediate way of determining whether the
RGMII delays should be applied by the PHY or by itself: by looking at
the port role (PHY or MAC). The port can be put in the PHY role either
explicitly (sja1105,role-phy) or implicitly (fixed-link).
We want to deprecate the sja1105,role-phy property, so all that remains
is the fixed-link property. Introduce a "fixed_link" array of booleans
in the driver, and use that to determine whether RGMII delays must be
applied or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang generates deadcode.DeadStores warnings when a variable
is used to read a value, but then that value isn't used later
in the code. Fix this warning.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Failing to add or remove LLDP filter doesn't seem to be a fatal
error, so downgrade the dev_err message to a dev_dbg message.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Peng Li