Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a couple of different variants of Kirkwood, which differ in
the pin muxing. These DTSI files set the correct compatibility and
define commonly used groups of pins, which board dbs files can
reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the ongoing conversion of Orion SoCs to DT, make use of
gpio and pinctrl drivers through DT. The main dtsi for Dove is prepared
to allow board specific descriptors to make use of pinctrl muxing.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB and HDD using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to SATA0 and SATA1 using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Also enable the gpio-poweroff driver when DT is used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The default chip-delay of 25us is a bit too tight for some DNS-320's,
and D-Link seem to specify 30us in their kernels for both devices.
Increase to 35us to make sure the NAND is stable.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Modern GCC can generate code which makes use of the CPU's native
unaligned memory access capabilities. This is useful for the C
decompressor implementations used for unpacking compressed kernels.
This patch disables alignment faults and enables the v6 unaligned
access model on CPUs which support these features (i.e., v6 and
later), allowing full unaligned access support for C code in the
decompressor.
The decompressor C code must not be built to assume that unaligned
access works if support for v5 or older platforms is included in
the kernel.
For correct code generation, C decompressor code must always use
the get_unaligned and put_unaligned accessors when dealing with
unaligned pointers, regardless of this patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of github.com:MISL-EBU-System-SW/mainline-public into mevbu-dt-additions
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds initial dts file for EXYNOS5440 SoC and adds the
dts file for SSDK5440 board which is a kind of reference board.
More properties will be added later.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCtU90ACgkQ9lPLMJjT96dSdQCfcmuU/3oXziktW6coEOwWD0rZ
rpAAoITtWPO7RNRqhCVQGFJKuuy5sid7
=ME0a
-----END PGP SIGNATURE-----
Merge tag 'marvell-openblocks-i2c-sata-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Marvell SATA and I2C enabling for OpenBlocks AX3-4
This patch enables SATA support on the OpenBlocks AX3-4. It has one
internal SATA port, and an external eSATA port.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 has a Seiko Instruments S-35390A as the RTC
controller. This patch enables this RTC device in the OpenBlocks
AX3-4 Device Tree.
[Thomas Petazzoni: updated with other OpenBlocks changes, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 board, based on the Armada XP SoC, has an I2C
bus. This patch enables this bus and sets the clock frequency of the
bus.
[Thomas Petazzoni: updated with other changes on OpenBlocks, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Armada 370 and Armada XP have the same I2C controllers as previous
Marvell SoCs, so the existing mv64xxx-i2c driver works fine.
[Thomas Petazzoni: updated on top of other Armada 370/XP changes,
rephrased the commit log].
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit converts the 'LaCie Ethernet Disk mini v2' board to the
Device Tree. All devices that have existing Device Tree bindings are
converted over to the Device Tree, the other devices remain
instantiated in the old way, until the respective drivers get the
needed Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds basic DT support for the Orion5x SoC family. It adds
an orion5x.dtsi description of the Orion5x SoC as well as the needed
DT_MACHINE structure to support boards converted to DT in the future.
So far, the Device Tree contains the interrupt controller, the GPIO
bank, the UART controllers, the SPI controller, the watchdog, the SATA
controller, the I2C controller and the cryptographic engine.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Hello, Andrew
> > +#define NSA310_GPIO_LED_ESATA_GREEN 12
> > <..>
> > +#define NSA310_GPIO_POWER_OFF 48
>
> It looks like most of these are not used. Please remove them.
True. Fixed.
> > +static struct mtd_partition nsa310_mtd_parts[] = {
> > + {
> > + .name = "uboot",
> > + .offset = 0,
> > + .size = 0x100000,
> > + .mask_flags = MTD_WRITEABLE,
> > + }, {
> > <..>
> You should be able to put all that into DT. Take a look at
Correct. I did the conversion and tested that the partitions
can be read with dd and produce exactly the same data before and
after conversion. So, the partition offsets at least should be fine.
> > +static struct i2c_board_info __initdata nsa310_i2c_info[] = {
> > + { I2C_BOARD_INFO("adt7476", 0x2e) },
> > +};
>
> You can also do this in DT as well. kirkwood-ts219.dtsi has
>
> i2c@11000 {
> status = "okay";
> clock-frequency = <400000>;
Ok, I did convert the i2c definition to use the devicetree.
The adt7476 device itself is not at reach of device tree,
AFAIK and requires more work at there?
Thanks for your valuable comments. Following is a new patch that
should address the problems and mistakes you pointed and also
some of the pointed by Jason Cooper. The nand and i2c are now
defined at DT and I also removed the pointless defines and
ARM_APPENDED_DTB. It is based against the Linus' official
3.6 version.
Best regards,
Tero
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a new kirkwood box made by Universal Scientific Industrial, Inc.
The product description is here:
http://www.usish.com/english/products_topkick1281p2.php
It is very similar to the dreamplug and other plug devices, with the
exception that it has room for a 2.5" SATA HDD internally.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Remove board specific gpio-fan driver registration. Moved into device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs/LcACgkQCwYYjhRyO9WrOgCfeWpA9XdQnwexySw5tPXS7Qdp
aJEAn2ql07SECpTRWezTJptHL0oI1dFF
=b0T7
-----END PGP SIGNATURE-----
Merge tag 'marvell-hwiocc-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Add hardware I/O coherency support for Armada 370/XP
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
From Michal Simek:
This branch depends on arm-soc devel/debug_ll_init branch because
we needed Rob's "ARM: implement debug_ll_io_init()"
(sha1: afaee03511ba8002b26a9c6b1fe7d6baf33eac86)
patch.
This branch also depends on zynq/dt branch because of previous major
zynq changes.
zynq/cleanup branch is subset of zynq/dt.
* 'zynq/multiplatform' of git://git.monstr.eu/linux-2.6-microblaze:
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Add/add conflict in arch/arm/Kconfig.debug.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: EXYNOS: DT Support for SATA and SATA PHY
ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
ARM: dts: Add node for touchscreen for exynos4210-trats
ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
ARM: dts: Add node for i2c3 bus for exynos4210-trats
ARM: dts: Add nodes for GPIO keys available on Trats
ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
ARM: dts: Add nodes for pin controllers for exynos4x12
pinctrl: samsung: Add support for EXYNOS4X12
gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
ARM: dts: add board dts file for EXYNOS4412 based SMDK board
ARM: dts: Add support for EXYNOS4X12 SoCs
ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
ARM: EXYNOS: Add MFC device tree support
ARM: dts: Enable serial controllers on Origen and SMDKV310
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
...
Add/add conflicts in:
arch/arm/boot/dts/exynos5250-smdk5250.dts
arch/arm/boot/dts/exynos5250.dtsi
arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Here is a pull request to add the support for Allwinner A10 SoCs.
* sunxi/soc2:
ARM: sunxi: Add sunxi restart function via onchip watchdog
ARM: sunxi: Add sun4i and cubieboard support
ARM: sunxi: Add earlyprintk support for UART0 (sun4i)
ARM: sunxi: Restructure sunxi dts/dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This includes supporting legacy i2c controller and ARM down clock
support for exynos5 and small changes.
[olof: It contains a dependency on samsung/hdmi for HDMI DT bindings, for some reason.]
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* samsung/pinctrl:
pinctrl: samsung: Update error check for unsigned variables
pinctrl: samsung: Add support for EXYNOS4X12
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
pinctrl: samsung: Use one GPIO chip per pin bank
pinctrl: exynos: Use one IRQ domain per pin bank
pinctrl: samsung: Include bank-specific eint offset in bank struct
pinctrl: samsung: Hold pointer to driver data in bank struct
pinctrl: samsung: Match pin banks with their device nodes
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
pinctrl: samsung: Distinguish between pin group and bank nodes
pinctrl: samsung: Remove static pin enumerations
pinctrl: samsung: Assing pin numbers dynamically
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
pinctrl: samsung: Detect and handle unsupported configuration types
From Kukjin Kim:
This is for adding support for DT based exynos5250 hdmi and it adds
device node for hdmi, mixer, hdmiphy and hdmiddc.
* 'next/hdmi-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
From Alexander Shiyan:
The main direction of this patchset - approaching the platform to the
possibility of using configurations with multiple platforms in a single
kernel. Added support of the majority of the necessary kernel symbol.
Also part of the driver code used only for the platform was moved to the
board code and converted to the use of standard drivers.
* clps711x/soc2:
MAINTAINERS: Add ARM CLPS711X entry
ARM: clps711x: Update defconfig due latest changes and new kernel symbols
ARM: clps711x: Rename board files to match functionality
ARM: clps711x: edb7211: Add support for NOR-Flash
ARM: clps711x: Moving backlight controls of framebuffer driver to the board
ARM: clps711x: p720t: Special driver for handling NAND memory is removed
ARM: clps711x: Moving power management of framebuffer driver to the board
ARM: clps711x: autcpu12: Special driver for handling NAND memory is removed
ARM: clps711x: Unused empty "ACK" calls for IRQ-chips removed
ARM: clps711x: Add FIQ interrupt handling
ARM: clps711x: Implement usage "MULTI_IRQ_HANDLER" kernel option for a platform
ARM: clps711x: Implement usage "SPARSE_IRQ" kernel option for a platform
ARM: clps711x: cdb89712: Special driver for handling memory is removed
ARM: clps711x: Always select AUTO_ZRELADDR for a platform
ARM: clps711x: p720t: Unneeded inclusion of head-sa1100.S removed
ARM: clps711x: Transform clps711x-framebuffer to platform driver and use it
ARM: clps711x: p720t: Using "leds-gpio" driver for LED control
ARM: clps711x: Using platform_driver for ethernet device
Armada 370 and XP come with an unit called coherency fabric. This unit
allows to use the Armada 370/XP as a nearly coherent architecture. The
coherency mechanism uses snoop filters to ensure the coherency between
caches, DRAM and devices. This mechanism needs a synchronization
barrier which guarantees that all the memory writes initiated by the
devices have reached their target and do not reside in intermediate
write buffers. That's why the architecture is not totally coherent and
we need to provide our own functions for some DMA operations.
Beside the use of the coherency fabric, the device units will have to
set the attribute flag of the decoding address window to select the
accurate coherency process for the memory transaction. This is done
each device driver programs the DRAM address windows. The value of the
attribute set by the driver is retrieved through the
orion_addr_map_cfg struct filled during the early initialization of
the platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch enhances the IRQ controller driver to add support for
Inter-Processor-Interrupts that are needed to enable SMP support.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a power management service unit
which is responsible for powering down and waking up CPUs and other
SOC units. This patch adds support for this unit.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a coherency fabric unit which
is responsible for ensuring hardware coherency between all CPUs and
between CPUs and I/O masters. This patch provides the basic support
needed for SMP.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch modifies pin control groups of SD pins on EXYNOS4210
and EXYNOS4X12 to use drive strength 3 as a default value which
corresponds to S5P_GPIO_DRVSTR_LV4 in legacy non-DT code.
This is needed at least on Origen board for sdhci2 to work and
if any other drive strength is required on each board, we can
overide it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited commit message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes for power domains available
on EXYNOS4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds fixed voltage vmmc regulator to dts file of Origen
board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies sdhci nodes present in Origen device tree source
to use current generic mmc bindings.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates all parts of Origen dts related to pin configuration
to use new GPIO and pinctrl bindings, instead of (now unsupported on
Exynos4) legacy gpio-samsung bindings.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes memory configuration defined in dts file of Origen
board from single 1 GiB section into four 256 MiB sections to match
section size limit.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is similar to a recent commit for exynos5250 titled:
ARM: EXYNOS: Add aliases for i2c controller
Adding aliases will be useful to prevent warnings in a future
change. See:
i2c: s3c2410: Get the i2c bus number from alias id
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Pawel Moll:
* 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove motherboard dependencies in the DTS files
ARM: vexpress: Start using new Versatile Express infrastructure
ARM: vexpress: Add config bus components and clocks to DTs
mfd: Versatile Express system registers driver
mfd: Versatile Express config infrastructure
From Stephen Warren:
ARM: bcm2835: core SoC enhancements
A machine restart/reboot implementation is added. The GPIO/pinmux
controller is instantiated, and dummy gpio.h added.
* tag 'bcm2835-for-3.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: enable GPIO/pinctrl
ARM: bcm2835: implement machine restart hook
Signed-off-by: Olof Johansson <olof@lixom.net>
From Stephen Warren:
ARM: tegra: core SoC code enhancements
Various small clock initialization table and driver changes to support
WiFi modules, SPI controllers, and host1x (graphics/display hardware).
Various AHB/APB-related clocks were added to the Tegra30 clock driver.
The level 2 cache initialization is now driven by data from device tree,
and the cache configuration tweaked.
AUXDATA is added to support SPI controllers and host1x.
Code to decode Tegra's "speedo" process identification fuses is added.
This pull request is based on tegra-for-3.8-cleanup.
* tag 'tegra-for-3.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (26 commits)
ARM: tegra: Add Tegra30 host1x clock support
ARM: tegra: Add AUXDATA for Tegra30 host1x
ARM: tegra: Add Tegra20 host1x clock support
ARM: tegra: Add AUXDATA for Tegra20 host1x
ARM: tegra: Tegra30 speedo-based process identification
ARM: tegra: Add speedo-based process identification
ARM: tegra: flexible spare fuse read function
ARM: tegra: Implement 6395/1 for Tegra
ARM: tegra: Add OF_DEV_AUXDATA for sflash driver in board dt
ARM: tegra: enable data prefetch on L2
ARM: tegra: Add OF_DEV_AUXDATA for SLINK driver in board dt
ARM: tegra: common: using OF api for L2 cache init
ARM: tegra: dt: add L2 cache controller
ARM: tegra30: clocks: add AHB and APB clocks
ARM: tegra: set up wlan clocks for tegra dt
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
...
From Lee Jones. It's an update of the previous ux500/dt branch with a few more
patches:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Describe UART platform registering issues more accurately
ARM: ux500: Enable all MMC devices on the u9540 when booting with DT
ARM: ux500: Enable SDI4 port on the u9540 when booting with Device Tree
ARM: ux500: Add UART support to the u9540 Device Tree
ARM: ux500: Add skeleton DTS file for the u9540
ARM: ux500: Add SDI (MMC) support to the HREF Device Tree
ARM: ux500: Move regulator-name properties out to board DTS files
Signed-off-by: Olof Johansson <olof@lixom.net>
This time, only one patch: Adding the motor PWM to lpc32xx.dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBQqPx0caH/YBv43g8RAuzFAKCFpy/LcErik0mFUeyNJrPz3/l1gACgmng4
SUDHt4IfsbL9iYlLIqkEIFM=
=p23Y
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-dts-for-3.7' of git://git.antcom.de/linux-2.6 into next/dt
From Roland Stigge:
DTS updates for the LPC32xx Soc for 3.7
This time, only one patch: Adding the motor PWM to lpc32xx.dtsi
* tag 'lpc32xx-dts-for-3.7' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add the motor PWM to base dts file
Signed-off-by: Olof Johansson <olof@lixom.net>
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQppFoAAoJEMzrak5tbycx1WsQALzqZBCebkEIo0CfuYlVtZrX
co2HBLsTis8KOI1lB5hZZdLvOD2sevwkw+YDtoG1k2ymZvR/Lpl3zdYdPCinA7gb
Qzs+OlwnAla7J5BkgV0v69lZHBYd8jvxsFt9MZo1XkHjw2IRPyrzLhdmBHGLVj3J
Tk7kk4OH64sDhDb+vZJXCtBJV0fvn10WNSskUHoQYZveGOCFGZXogrAht25tcoQO
TM89tasMdRq3IhOxuzHHo/7AegyuTZdDzV4blNr1xOMzyz1b3P3sBh2ZiK+aBztX
CCfpJ2ZUlRqTKSOU4qlM48dWffr/ZyP1u0VVi9Bu4Df/qBpS37NjagiVxMhiEasz
0f3SZTAkZGh7yxi/BTmqu6vvQ0FWYgtOJPezK19RMXistdQkA/uiQDKqeBMTLTeA
UXCnJdC05uBWhymy8DhJyryPQCJ1k3PJ+4pSmzemWIaAoQqpaH/q5yp4IAccr8wO
pxZPtddD030iVdT5oYqBoAhn2W/mKtG1fShhp7wpj/qRYecUQICocTavuFG3DK0N
k1OJ9rTxBZfnyeCBF/wdS/nNuI9xDk2WULVIya2cNu8I/te6QKp1fd4Jr3aPnZ/9
4hiw5+L2dw2z7447EwlryC4sHttjVYEDHqsedR39YNPIn55D3mfsNX2iCczk1ZDU
+OoRMiATrjILb1sOjJAs
=ytxh
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aH3p
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup for 3.8
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
* tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
iommu: tegra: remove include of <mach/iomap.h>
staging: nvec: remove include of <mach/iomap.h>
crypto: tegra: remove include of <mach/clk.h>
ARM: tegra: update *.dts for regulator-compatible deprecation
usb: phy: tegra remove include of <mach/iomap.h>
usb: host: tegra remove include of <mach/iomap.h>
- conversion of watchdog to DT
- usart definition for evk-pro3 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQqm8pAAoJEAf03oE53VmQpEEH/00dsxSUrL06NzwP8Y1+UjW8
OXJPJUU0Mor/b5zCp3wsxB4+imZ4y4oqJ42qvFZjRLHj0KMvVdnxm5SNIpbQtXxV
jXPqXYk8yfH4YF3DDLuiD9wkXjwtgck7+D7ogcAIb9bbWyyGusKIcs72smvGanCd
zZrWIOGwXlqgrF5CX8kl6SIhdnYvMtee7GlzbiFHlKr4CLPOIR3iahnHR26gkzLH
cRjYVujYaHpQKBR8XvMgIl7brCUTX2KuMajvVOF8EShk8BU2MW1GHFY0cNfqaKRn
R/Z9itXk6P/h3s/Wf+Qyfpuz3E0zbS80uN/NyrIbcGbAQQIesuo8pcd9xZZ5yg0=
=whJu
-----END PGP SIGNATURE-----
Merge tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
More DT material for AT91:
- conversion of watchdog to DT
- usart definition for evk-pro3 board
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: evk-pro3: enable watchdog
ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
watchdog: at91sam9_wdt: add device tree support
ARM: at91: dt: evk-pro3: enable uart0 and uart2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCmwSAACgkQGxsu9jQV9nbssgCcChzwuFlPkP4sVdTtAGGh5mWD
rNcAn3PfG1ByMR57GkDtdQiAjS5N2dME
=Pi49
-----END PGP SIGNATURE-----
Merge tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner SoC support for 3.8
* tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux:
ARM: sunxi: Add entry to MAINTAINERS
ARM: sunxi: Add device tree for the A13 and the Olinuxino board
ARM: sunxi: Add earlyprintk support
ARM: sunxi: Add basic support for Allwinner A1x SoCs
irqchip: sunxi: Add irq controller driver
clocksource: sunxi: Add Allwinner A1X Timer Driver
clk: sunxi: Add dummy fixed rate clock for Allwinner A1X SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple devices' DT compatible values only contained the device name
without any vendor prefix. Add the missing vendor prefixes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This dts file is based on the Snow dts file in the Chromium OS kernel
tree with the following changes:
* Some details have been updated to match the exynos5250-smdk5250.dts
file from linux-next (as of c11068538994430547722dc9fb515a0ceefd5cb9).
* This file doesn't include references to hardware whose upstream
support isn't quite there yet. That includes most i2c devices.
Note that most i2c busses have been included with no devices.
The Snow dts file is mostly just an include of the "cros5250" dts file
which describes a class of similar boards. Support for other boards has
not yet been send upstream.
With this file and a change to use UART3 for serial output I can:
* Boot to a command line using either SD or EMMC as a root filesystem
* See the power button and lid switch using evtest.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The aliases for dwmmc were placed in the SMDK5250 dts file but really
should be common for all exynos5250 boards. Move it to the common CPU
file.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCmB6oACgkQ9lPLMJjT96elAwCfQyZY9HP0PW+0y2VRbKLYlrTW
vaQAoJMNKRaxjBwnF5As4I4/5g0rsE/H
=hRb7
-----END PGP SIGNATURE-----
Merge tag 'marvell-boards-net-for-3.8' of github.com:MISL-EBU-System-SW/mainline-public into test-the-merge
Marvell boards changes related to Ethernet, for 3.8
Conflicts:
arch/arm/boot/dts/armada-370-xp.dtsi
arch/arm/boot/dts/armada-xp-db.dts
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvneta driver for the Marvell Armada 370/XP Ethernet devices has
gained proper clock framework integration, and the corresponding
Device Tree nodes now have a correct 'clocks' pointer.
The 'clock-frequency' properties in the various .dts files for Armada
370/XP boards have therefore become useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvneta driver now understands a standard 'clocks' clock pointer
property in the Device Tree nodes for the Ethernet devices, so we add
the right clock reference for the different Ethernet ports of the
Armada 370/XP SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With DT support for Marvell XOR DMA engine, make use of it on Dove.
Also remove the now redundant code in DT board init for xor engines.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use DT to describe the two XOR DMA engines on Kirkwood. Remove the
C code initialization.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add the SATA device tree bindings for
- Armada XP evaluation board (DB-78460-BP)
- Armada 370 evaluation board (DB-88F6710-BP-DDR3)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds support for the Cubieboard based on the Allwinner
A10/sun4i SoC. Currently only UART is supported. Other devices
will eventually follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For the new sun4i/Cubieboard (A10) support, lets re-strucure the
sun5i dts files to make it more generic. Those are the new
dts/dtsi files:
sunxi.dtsi - Devices common to all Allwinner sunXi SoC's
sun4i.dtsi - sun4i Devices, will include sunxi.dtsi
sun5i.dtsi - sun5i Devices, will include sunxi.dtsi
board.dts - will include either sun4i.dtsi or sun5i.dtsi
Additionally the "duart" label in the olinuxino.dts is changed to
"uart1".
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
With true DT clock providers available switch Dove clock setup in DT-
enabled boards. While AUXDATA can be removed completely from bus probing,
some devices still don't know about DT at all. Therefore, some clock
aliases are created until the devices also move to DT.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds Device Nodes for SATA and SATA PHY device.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
[kgene.kim@samsung.com: removed address definitions as per comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The broken voltage property has been replaced with auto detection based
on voltages available on vmmc voltage regulator, so there is no use for
it now.
This patch removes the now unused property from Trats Device Tree
sources.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a device tree node for the Melfas MMS114-controlled
touchscreen present on Samsung Trats board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree node for a fixed voltage regulator used for
touchscreen on Samsung Trats board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree node for i2c3 bus to device tree source
of Samsung Trats board. This bus is used by mms114 touchscreen
controller, for which support will be added in separate patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch extends dts file of Samsung Trats board to add support for
available GPIO keys using gpio-keys driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates all parts of Trats dts related to pin configuration
to use new GPIO and pinctrl bindings, instead of (now unsupported on
Exynos4) legacy gpio-samsung bindings.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.
v2 patch mods
--------
- Remove l2x0_of_init call as there were problems with the code.
A separate patch will be submitted with cache init code
- Rename capri files and refs to bcm281xx-based names
- Add bcm281xx binding doc
- various misc cleanups
v3 patch mods
-------------
- Remove extra #include lines
- Remove remaining references to capri
- dt uart chipset string added
- cleaned up chip # references
v4 patch mods
-------------
- swap order of compatible definitions for uart
- fix typo
v5 patch mods
-------------
- Rename bcm281xx to bcm11351 in dts+code,
leaving references to bcm281xx only in help+comments.
v6 patch mods
-------------
- fix typo in uart 'compatible' string
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The dtb targets belong in arch/arm/boot/dts/Makefile now, so move the
newly added davinci targets there.
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/FbB
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
These changes add DT boot support to DaVinci DA850
SoC.
* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: generate dtbs for da850 boards
ARM: davinci: add support for am1808 based EnBW CMC board
ARM: davinci: da850 evm: add DT data
ARM: davinci: da850: add SoC DT data
ARM: davinci: da850: add DT boot support
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device tree support for charging algorithm driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for ab8500-charger driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for battery-temperature-monitor driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- This patch adds device tree support for fuelgauge driver
- optimize bm devices platform_data usage and of_probe(...)
Note: of_probe() routine for battery managed devices is made
common across all bm drivers.
- test status:
- interrupt numbers assigned differs between legacy and FDT mode.
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds nodes for pin controllers available on
EXYNOS4X12 SoCs supported by pinctrl-samsung driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This hooks the Integrator/CP into the SoC bus when booting from
device tree, by mapping the CP controller registers first,
then registering the SoC device, and then populating the device
tree with the SoC device as parent.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This hooks the Integrator/AP into the SoC bus when booting from
device tree, by mapping the AP controller registers first,
then registering the SoC device, and then populating the device
tree with the SoC device as parent.
Introduce some helpers in the core to provide sysfs files
detailing the use of the SoC ID which will later be reused by
the Integrator/CP patch for the same bus grouping.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This will allow timer.c to use twd_local_timer_of_register(), and
hence not need to hard-code the TWD address or IRQ.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra RTC maintains seconds and milliseconds counters, and five alarm
registers. The alarms and other interrupts may wake the system from
low-power state.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra timer provides a number of 29-bit timer channels, a single
32-bit free running counter, and in the Tegra30 variant, 5 watchdog modules.
The first two channels may also trigger a legacy watchdog reset.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable host1x, and the HDMI output. Whistler also has a DSI-based LCD,
and a VGA output. tegradrm doesn't support either of those output types
yet.
Based on work by Thierry Reding for TrimSlice.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There are also a few imx6 improvement patches in there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQpeRkAAoJEFBXWFqHsHzOHMoH/3pxLWMHlaFFN70gm33GIEpj
6/P0afKhjEseQDfbvLPfRPwHTQIkw/xQ2rfSrZGUnhgAGN2SfOcxiREFpdChgqyb
b5kO+3oQpnQTFce6tuqCI8j4LAqr63AHhJPWZuDEBaR52Vs0i9gYr2Zwv7i+iUh7
fuLu+NDQLKOkEW7W97FRFVWKRGmSMhJYvhNn+kgleFUhvzUKpJ6n7kFsT05BSl97
EiJHtVxOv+RtlFvx7jrTr18NM2i4Kb4IzEfLzgYOowK9cwfNuhnaxsQvAUiGSa+z
EuvXdKN2btW0PtqHVBPdz5T0OzTyJheaCETKTqz0XM32/SVz5Ma3gZEEDagGLiw=
=zBAI
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch. Most of them are dts changes.
There are also a few imx6 improvement patches in there.
* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: select ARM and PL310 errata
ARM: imx6q: print silicon version on boot
ARM i.MX dts: Consistently add labels to devicenodes
ARM: dts: imx6q-sabresd: add volume up/down gpio keys
ARM: dts: imx53: pinctl update
ARM: imx: enable cpufreq for imx6q
ARM: dts: imx6q: enable snvs lp rtc
ARM: dts: imx6q-sabreauto: Add basic support
ARM: imx6q: let users input debug uart port number
ARM: dts: imx53-qsb: Make DA9053 regulator functional
ARM: dts: imx53-qsb: Use pinctrl for gpio-led
ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>
source updates. One timer improvement and one defconfig update are
also included there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQpeyAAAoJEFBXWFqHsHzOgpsH/3b8dVbanZFsAwm5z1rF2DY2
xrI5Xjqmk8K76CoZopRjQo/u6/SFbARzhClzCywBZKeVDM4Ah15bAN7wABmLgaVV
xMDF8pA9mDZCzRwKEH6SG85n2/lMupG6qjbDNG22FXYfUAYJRxopoSDdNjfkvYr0
Da5ZcvC9qvYnyyp37vYTI6CVO4EgJseoirvaJOKCALb5FFpzq0QEkEYK6IIx7pg3
j9K2ZPy4/MIrsQQMyiv9AFEbUkUWy+deuTHv9Sl8+ddoqPtqNy4EfICt+no5uBmp
frDg003/67Pz/fIm7lJ5IMBF4X0TW4OqMv9c2afG8/kJP34rXnBJVHdLKil731k=
=jEM1
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
It's mxs device tree changes for 3.8. The majority is device tree
source updates. One timer improvement and one defconfig update are
also included there.
* tag 'mxs-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs_defconfig: Improve USB related support
ARM: mxs: apf28dev: Add I2C and SPI support
ARM: mxs: Setup scheduler clock
ARM: dts: mxs: Add hog pins to Crystalfontz boards
ARM: dts: cfa10036: Use pinctrl for power led
ARM: mxs: apf28dev: Add LCD and backlight support
ARM: mxs: apf28dev: Add pinctrl and gpios
ARM: dts: mxs: Add 16 bits LCD screen muxing options for I.MX28
ARM: dts: cfa10049: Add the DH2228FV DAC to the DTS
ARM: mxs: Add support for the Armadeus Systems APF28Dev docking board
ARM: mx28: Skip OCOTP FEC MAC setup if in DT
ARM: dts: mxs: Add PWM3 muxing options for i.MX28
ARM: mxs: Add support for the Armadeus Systems APF28 module
ARM: dts: cfa10049: Add FEC to the CFA-10049 expansion board
ARM: dts: imx23-olinuxino: Use pinctrl for gpio-led
ARM: dts: imx23-olinuxino: Remove unneeded "default-on"
ARM: dts: imx28-evk: Use pinctrl for gpio-led
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the HDMI output found on Tamonten Evaluation Carrier boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the HDMI output found on Plutux boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Hook up the required regulators, I2C DDC adapter and hotplug detect GPIO
to the Tamonten HDMI output. Carrier boards still need to explicitly
enable the output to use it.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable host1x, and the HDMI output. Harmony also has a DVI port with an
HDMI form-factor connector, driven by Tegra's LVDS output. This isn't
enabled yet, due to potential issues with having multiple outputs enabled.
Correct DDC I2C frequency to 100KHz.
Add dummy/fixed regulators to satisfy the HDMI driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
[swarren: add commit description, remove enable of DVI port]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable host1x, and the HDMI output. Harmony also has an optional LCD,
and a VGA output. The former isn't enabled due to potential issues with
having multiple outputs enabled. The latter isn't enabled since the
driver doesn't support VGA yet anyway.
Correct DDC I2C frequency to 100KHz.
Based on work by Thierry Reding for TrimSlice.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CFfP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for 3.8
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
Add device tree file for the armadeus apf27
ARM i.MX: Add Ka-Ro TX25 devicetree
ARM i.MX25: Add devicetree
ARM i.MX25: Add devicetree support
ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
based on imx-multiplatform branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=P3UZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX SoC updates
based on imx-multiplatform branch.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX51 babbage: Add display support
ARM i.MX6: Add IPU support
ARM i.MX51: Add IPU support
ARM i.MX53: Add IPU support
ARM i.MX5: switch IPU clk support to devicetree bindings
ARM i.MX6: fix ldb_di_sel mux
ARM i.MX51: setup MIPI during startup
mx2_camera: Fix regression caused by clock conversion
ARM: clk-imx27: Add missing clock for mx2-camera
ARM i.MX27: Fix low reference clock path
ARM: dts: imx27-3ds: Remove local watchdog inclusion
watchdog: Support imx watchdog on SOC_IMX53
ARM: mach-imx: Support for DryIce RTC in i.MX53
ARM : i.MX27 : split code for allocation of ressources of camera and eMMA
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The babbage board has a DVI-I output which allows to output analog
and digital signals simultaneously. This patch adds support for it
to the devicetree. The DDC signals are not wired up on the board, so
DRM will fall back on default VESA modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This adds the IPU device to the devicetree along with the necessary pinctrl
settings for the parallel display outputs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
imx27.dtsi already register the watchdog, so no need to do it in the board dts
file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested on an at91sam9260 board (evk-pro3).
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
enable the dma support for auart0 in mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Globalscale Mirabox platform has two Ethernet interfaces,
connected to the SoC with a RGMII interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The PlatHome OpenBlocks AX3-4 platform has 4 Ethernet ports, connected
to a single quad-port PHY through SGMII.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch enables the two network interfaces of the Armada 370
official Marvell evaluation platform, and the four network interfaces
of the Armada XP official Marvell evaluation platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Armada 370 SoC has two network units, while the Armada XP has four
network units. The first two network units are common to both the
Armada XP and Armada 370, so they are added to armada-370-xp.dtsi,
while the other two network units are specific to the Armada XP and
therefore added to armada-xp.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Having labels before each node allows board bindings to reference
to nodes by using the &nodename {} notation. This way boards do not
have to resemble the whole devicetree layout. Due to less indention
needed the board files also get better readability. Since the label
make the documentation behind the nodes unnecessary it is removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch supplements pinctl support on i.MX53.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.
This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to Documentation/devicetree/bindings/mmc/mmc.txt bus-width
is a mandatory property. While this is currently enforced nowhere, it's
a good habit to just add the property now to allow to add common helper
functionality for the mmc property parsing later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
convert at91sam9g20ek with wm8731 to device tree support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the host1x node along with its children to the Tegra30 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the host1x node along with its children to the Tegra20 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Nvidia's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add DT entry for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: move sflash node to keep file sorted]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an ON Semiconductors NCT1008 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tamonten SOM has an ON Semiconductor NCT1008 connected to the DVC
bus which is used to measure the ambient (local) temperature as well as
the on-die (remote) temperature.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an Analog Devices ADT7461 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
These properties are already set by the tegra20-tamonten.dtsi, so they
don't need to be repeated.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This commit allows the I2C2 controller on Tegra20 to be routed either to
the DDC or the PTA pin group at runtime. On Tamonten this allows the I2C
bus to be used for the DDC of the HDMI connector or to access I2C chips
on the carrier board.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.
SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add slink controller details in the dts file of
Tegra20 and Tegra30.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra 2's I2C2 controller can be routed to either the PTA
or DDC pin group on Ventana. So:
- Remove the HDMI function definition of pta pingroup
- Define child i2c adapters(ddc & pta) for I2C2 controller
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller for a02 and a04 board, which is connected to the
WiFi module.
For now, always enable the regulator that provides power to the Wifi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller, which is connectted to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the SDHCI1 controller. This is connected to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
various .dts files, and timer related changes to allow
configuring the timer via device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=59qq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:
Device tree related changes for omaps updating the
various .dts files, and timer related changes to allow
configuring the timer via device tree.
* tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (48 commits)
usb: musb: dsps: dt binding - add resources, example
ARM: dts: omap4-sdp: Add pinmux configuration for HDMI
ARM: dts: omap4-panda: Add pinmux configuration for HDMI
ARM: dts: Makefile: Add the am335x-evmsk target in dtbs list
ARM: dts: AM33XX: Add usbss node
ARM: dts: AM33XX: Add push-buttons device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-keys to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-leds to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-bone
ARM: dts: AM33XX: Add pinmux configuration for user-leds to BONE
ARM: dts: AM33XX: Add volume-keys device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for volume-keys to EVM
ARM: dts: AM33XX: Add matrix keypad device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for matrix keypad to EVM
ARM: dts: omap5-evm: LPDDR2 memory device details for EVM
ARM: dts: omap5: EMIF device tree data for OMAP5 boards
ARM: dts: omap5-evm: Fix size of memory defined for EVM
ARM: OMAP2+: Add device-tree support for 32kHz counter
ARM: OMAP: Add DT support for timer driver
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds device tree properties for ST-Ericsson DB8500 thermal driver,
also adds the platform data to support the old fashion.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add CPSW and MDIO related device tree data for AM33XX.
Also enable them into board/evm dts files by providing
respective phy-id.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the Device Tree files for Armada 370 and XP SoCs and boards use
the "armada-370-xp" common compatible string, except
armada-370-xp.dtsi which was specifying "armada_370_xp".
Fix this inconsistency by making armada-370-xp.dtsi declare a
compatible string of "armada-370-xp" like everyone else.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This platform, available from Globalscale has an Armada 370. For now,
only the serial port is supported. Support for network, USB and other
peripherals will be added as drivers for them become available for
Armada 370 in mainline.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This is 3.8 material.
Changes from original version posted by Gregory:
* Renamed .dts file to armada-370-mirabox.dts
* Change compatible string to 'globalscale,mirabox'
* Remove compatible string from armada-370-xp.c
* Removed references to MBX0001
Andrew Lunn