This adds a driver that supports the GPIO block found in
MStar/SigmaStar ARMv7 SoCs.
The controller seems to have enough register for 128 lines
but where they are wired up differs between chips and
no currently known chip uses anywhere near 128 lines so there
needs to be some per-chip data to collect together what lines
actually have physical pins attached and map the right names to them.
The core peripherals seem to use the same lines on the
currently known chips but the lines used for the sensor
interface, lcd controller etc pins seem to be totally
different between the infinity and mercury chips
The code tries to collect all of the re-usable names,
offsets etc together so that it's easy to build the extra
per-chip data for other chips in the future.
So far this only supports the MSC313 and MSC313E chips.
Support for the SSC8336N (mercury5) is trivial to add once
all of the lines have been mapped out.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201129110803.2461700-4-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a binding description for the MStar/SigmaStar GPIO controller
found in the MSC313 and later ARMv7 SoCs.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201129110803.2461700-3-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Header adds defines for the gpio number of each pad from the driver view.
The gpio block seems to have enough registers for 128 lines but what line
is mapped to a physical pin depends on the chip. The gpio block also seems
to contain some registers that are not related to gpio but needed somewhere
to go.
Because of the above the driver itself uses the index of a pin's offset in
an array of the possible offsets for a chip as the gpio number.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201129110803.2461700-2-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.
Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=a7If
-----END PGP SIGNATURE-----
Merge tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 5.11
Here are the interconnect changes for the 5.10-rc1 merge window
consisting of new driver and a cleanup.
Driver changes:
- New driver for Samsung Exynos SoCs
- Misc cleanups
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
MAINTAINERS: Add entry for Samsung interconnect drivers
interconnect: Add generic interconnect driver for Exynos SoCs
interconnect: qcom: Simplify the vcd compare function
The sysfs in batman-adv support was marked as deprecated by the commit
42cdd52148 ("batman-adv: ABI: Mark sysfs files as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Second, and most likely final, set of fixes for v5.10. Small fixes and
PCI id addtions.
iwlwifi
* PCI id additions
mt76
* fix a kernel crash during device removal
rtw88
* fix uninitialized memory in debugfs code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyS7IAAoJEG4XJFUm622baIIH/jQl+ogi9RoL+96Fdo4eqltw
CGK3QP6GUlutKA6U9a7IKw9TTAu9nHPpBK5rLaFZCOmNsGprbyQ822UZt16s77XF
TBN/gTp/aeogRVfV07D5owNmjCO61WG2IvUOuP5T/td/0xsYxPH+0ESBNXXUy0bC
oIoQzYba1/uw0yVUyZezvZb+gPKIxWWZ8V9tuegcWrr0NsVsNFPFMGkTFt7BGqPm
LNCVMJy2v5XA25+TMTKgsrCbMeUl7ffADKFvqKm3i4kv57bYX67siDraNEWNWkhr
43MAG0p1p9tuxzubjv3ncOVvLU62Lvm03TG2r+NonSovXjueVG/wU3E4wADaLBI=
=JY9B
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.10
Second, and most likely final, set of fixes for v5.10. Small fixes and
PCI id addtions.
iwlwifi
* PCI id additions
mt76
* fix a kernel crash during device removal
rtw88
* fix uninitialized memory in debugfs code
* tag 'wireless-drivers-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
rtw88: debug: Fix uninitialized memory in debugfs code
mt76: usb: fix crash on device removal
iwlwifi: pcie: add some missing entries for AX210
iwlwifi: pcie: invert values of NO_160 device config entries
iwlwifi: pcie: add one missing entry for AX210
iwlwifi: update MAINTAINERS entry
====================
Link: https://lore.kernel.org/r/20201203183408.EE88AC43461@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MIPI CCS replaces SMIA and SMIA++ as the current standard. CCS brings new
features while existing functionality will be supported. Rename the
smiapp-pll as ccs-pll accordingly.
Also add Intel copyright to the files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's been a long time since I could credibly claim to be maintaining these
drivers; I'm not even sure my hardware works anymore. Mark them orphan.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
1. Add MT8167 support
2. Cleanup function
3. Convert the dpi bindings to yaml
4. Drop local dma_parms
5. Fix formatting and provide missing member description
6. Introduce GEM object functions
7. Fix aliases name
8. Move MIPI DSI phy driver to phy folder
-----BEGIN PGP SIGNATURE-----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=iVNn
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.11-2
1. Add MT8167 support
2. Cleanup function
3. Convert the dpi bindings to yaml
4. Drop local dma_parms
5. Fix formatting and provide missing member description
6. Introduce GEM object functions
7. Fix aliases name
8. Move MIPI DSI phy driver to phy folder
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130234807.936-1-chunkuang.hu@kernel.org
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Write the devicetree binding text file associated with
the Mellanox BlueField I2C controller in schema file,
JSON compatible subset of YAML. Besides, add an entry
within MAINTAINERS file.
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Amend the existing SMIA bindings by adding MIPI CCS support, with separate
compatible strings for CCS 1.0 and CCS 1.1. Rename the old bindings
accordingly as CCS is the current standard.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Convert nokia,smia DT bindings to YAML.
Also add explicit license to bindings.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the "smiapp" driver as "ccs". MIPI CCS is the contemporary standard
for raw Bayer camera sensors. The driver retains support for the SMIA++
and SMIA compliant camera sensors. A module alias is added for old user
space using "smiapp" module name.
Add Intel copyright while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions of the MIPI CCS 1.1 standard.
The CCS driver makes extended use of device's capability registers that
are dependent on CCS version. This involves having an in-memory data
structure for limit and capability information, creating that data
structure and accessing it.
The register definitions as well as the definitions of this data structure
are generated from a text file using a Perl script. Add the generator
script to make it easy to update the generated files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.
The driver is added as a pinctrl driver, albeit only having just GPIO
support currently. The hardware supports other functions that will be
added following.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201113145151.68900-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl/EM9oeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/3kH/RNkFyTlHlUkZpJx
8Ks2yWgUln7YhZcmOaG/IcIyWnhCgo3l35kiaH7XxM+rPMZzidp51MHUllaTAQDc
u+5EFHMJsmTWUfE8ocHPb1cPdYEDSoVr6QUsixbL9+uADpRz+VZVtWMb89EiyMrC
wvLIzpnqY5UNriWWBxD0hrmSsT4g9XCsauer4k2KB+zvebwg6vFOMCFLFc2qz7fb
ABsrPFqLZOMp+16chGxyHP7LJ6ygI/Hwf7tPW8ppv4c+hes4HZg7yqJxXhV02QbJ
s10s6BTcEWMqKg/T6L/VoScsMHWUcNdvrr3uuPQhgup240XdmB1XO8rOKddw27e7
VIjrjNw=
=4ZaP
-----END PGP SIGNATURE-----
Merge tag 'v5.10-rc6' into patchwork
Linux 5.10-rc6
* tag 'v5.10-rc6': (1815 commits)
Linux 5.10-rc6
sock: set sk_err to ee_errno on dequeue from errq
mptcp: fix NULL ptr dereference on bad MPJ
net: openvswitch: fix TTL decrement action netlink message format
perf probe: Change function definition check due to broken DWARF
perf probe: Fix to die_entrypc() returns error correctly
perf stat: Use proper cpu for shadow stats
perf record: Synthesize cgroup events only if needed
perf diff: Fix error return value in __cmd_diff()
perf tools: Update copy of libbpf's hashmap.c
x86/mce: Do not overwrite no_way_out if mce_end() fails
kvm: x86/mmu: Fix get_mmio_spte() on CPUs supporting 5-level PT
KVM: x86: Fix split-irqchip vs interrupt injection window request
KVM: x86: handle !lapic_in_kernel case in kvm_cpu_*_extint
usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
printk: finalize records with trailing newlines
can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
...
ld.lld 10.0.1 spews a bunch of various warnings about .rela sections,
along with a few others. Newer versions of ld.lld do not have these
warnings. As a result, do not add '--orphan-handling=warn' to
LDFLAGS_vmlinux if ld.lld's version is not new enough.
Link: https://github.com/ClangBuiltLinux/linux/issues/1187
Link: https://github.com/ClangBuiltLinux/linux/issues/1193
Reported-by: Arvind Sankar <nivedita@alum.mit.edu>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add an entry and email address for the new uv_sysfs driver and
its maintainer.
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lkml.kernel.org/r/20201125175444.279074-6-justin.ernst@hpe.com
Update bindings for the Dialog Semiconductor DA9121 voltage regulator to
add device variants.
Because several variants have multiple regulators, and to regard potential
to add GPIO support in future, the 'regulators' sub-node is added,
following the precedent set by other multi-regulator devices, including
the DA9211 family. This breaks compatibility with the original submission
by Vincent Whitchurch - but as this is still in for-next, the alignment
could be made before upstreaming occurs.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/0606d3ded5fef4c38760246146f197db4ce3a374.1606755367.git.Adam.Ward.opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
-----BEGIN PGP SIGNATURE-----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=mQNT
-----END PGP SIGNATURE-----
Merge tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
power-domains:
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
* tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (21 commits)
soc: mediatek: mmsys: Use devm_platform_ioremap_resource()
soc / drm: mediatek: Move DDP component defines into mtk-mmsys.h
soc: mediatek: add mt6779 devapc driver
dt-bindings: devapc: add bindings for mtk-devapc
soc / drm: mediatek: cmdq: Remove timeout handler in helper function
soc: mediatek: pm-domains: Add support for mt8192
soc: mediatek: pm-domains: Add default power off flag
soc: mediatek: pm-domains: Add support for mt8183
soc: mediatek: pm-domains: Allow bus protection to ignore clear ack
soc: mediatek: pm-domains: Add subsystem clocks
soc: mediatek: pm-domains: Add extra sram control
soc: mediatek: pm-domains: Add SMI block as bus protection block
soc: mediatek: pm_domains: Make bus protection generic
soc: mediatek: pm-domains: Add bus protection protocol
soc: mediatek: Add MediaTek SCPSYS power domains
dt-bindings: power: Add MT8192 power domains
dt-bindings: power: Add MT8183 power domains
dt-bindings: power: Add bindings for the Mediatek SCPSYS power domains controller
mfd: syscon: Add syscon_regmap_lookup_by_phandle_optional() function.
MAINTAINERS: change mediatek wiki page
...
Link: https://lore.kernel.org/r/b03fe343-e183-c6f3-f2dc-4c58aae3146b@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mediatek MIPI DSI phy driver is moved from drivers/gpu/drm/mediatek to
drivers/phy/mediatek, so add the new folder to the Mediatek DRM drivers'
information.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Add maintainers entry for the Samsung SoC interconnect drivers, this
currently includes the Exynos generic interconnect driver.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201112140931.31139-4-s.nawrocki@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add NXP PF8100/PF8121A/PF8200 regulator driver.
PF8100/PF8121A/PF8200 is PMIC designed for highperformance
consumer applications. It features seven high efficiency buck,
four linear and one vsnvs regulators.
Tested in Engicam i.Core MX8M Mini SOM platform boards.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201130112329.104614-2-jagan@amarulasolutions.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jason's email address has now been bouncing for weeks, and no
reply was received when trying to reach out on other addresses.
We really hope he is OK. But until we hear of his whereabouts,
let's move him to the CREDITS file so that people stop Cc-ing
him.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201128103707.332874-1-maz@kernel.org
Update the email to my kernel.org email address and update the git
repository address to the git.kernel.org
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have switched mvebu tree to kernel.org now, so update in
MAINTAINERS file
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
An entry is added for MikroTik CRS3xx 98DX3236 based switches.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Daniel Borkmann says:
====================
pull-request: bpf 2020-11-28
1) Do not reference the skb for xsk's generic TX side since when looped
back into RX it might crash in generic XDP, from Björn Töpel.
2) Fix umem cleanup on a partially set up xsk socket when being destroyed,
from Magnus Karlsson.
3) Fix an incorrect netdev reference count when failing xsk_bind() operation,
from Marek Majtyka.
4) Fix bpftool to set an error code on failed calloc() in build_btf_type_table(),
from Zhen Lei.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add MAINTAINERS entry for BPF LSM
bpftool: Fix error return value in build_btf_type_table
net, xsk: Avoid taking multiple skbuff references
xsk: Fix incorrect netdev reference count
xsk: Fix umem cleanup bug at socket destruct
MAINTAINERS: Update XDP and AF_XDP entries
====================
Link: https://lore.kernel.org/r/20201128005104.1205-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here are some small misc driver fixes for 5.10-rc6. They include:
- interconnect fixes for reported problems
- habanalabs bugfix for found issue when doing the switch fallthrough
patches.
- MAINTINERS file update for coresight reviewers/maintainers
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX8I/9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGGgCgkFW4ZPxvrJpoGHaA15Mlj8Gv5JwAn09Xh0Hz
BWxtCXL4EIngX/wE3ITy
=54XD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small misc driver fixes for 5.10-rc6. They include:
- interconnect fixes for reported problems
- habanalabs bugfix for found issue when doing the switch fallthrough
patches
- MAINTAINERS file update for coresight reviewers/maintainers
All have been in linux-next with no reported issues"
* tag 'char-misc-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Adding help for coresight subsystem
habanalabs/gaudi: fix missing code in ECC handling
interconnect: fix memory trashing in of_count_icc_providers()
interconnect: qcom: qcs404: Remove GPU and display RPM IDs
interconnect: qcom: msm8916: Remove rpm-ids from non-RPM nodes
interconnect: qcom: msm8974: Don't boost the NoC rate during boot
interconnect: qcom: msm8974: Prevent integer overflow in rate
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Another set of patches for devicetree files and Arm
SoC specific drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including
one regression for the CPSW network driver and a few
runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform,
in particular fixing the MMC device ordering that
recently became nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including
a regression fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the
NXP dpio driver
- A regression fix for a bug caused by an earlier bug
fix in the xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the
NXP LPC32xx platform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=yGOq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
and can subtrees.
Current release - regressions:
- gro_cells: reduce number of synchronize_net() calls
- ch_ktls: release a lock before jumping to an error path
Current release - always broken:
- tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header
Previous release - regressions:
- net/tls: fix missing received data after fast remote close
- vsock/virtio: discard packets only when socket is really closed
- sock: set sk_err to ee_errno on dequeue from errq
- cxgb4: fix the panic caused by non smac rewrite
Previous release - always broken:
- tcp: fix corner cases around setting ECN with BPF selection
of congestion control
- tcp: fix race condition when creating child sockets from
syncookies on loopback interface
- usbnet: ipheth: fix connectivity with iOS 14
- tun: honor IOCB_NOWAIT flag
- net/packet: fix packet receive on L3 devices without visible
hard header
- devlink: Make sure devlink instance and port are in same net
namespace
- net: openvswitch: fix TTL decrement action netlink message format
- bonding: wait for sysfs kobject destruction before freeing
struct slave
- net: stmmac: fix upstream patch applied to the wrong context
- bnxt_en: fix return value and unwind in probe error paths
Misc:
- devlink: add extra layer of categorization to the reload stats
uAPI before it's released
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1tQm
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc6, including fixes from the WiFi driver,
and CAN subtrees.
Current release - regressions:
- gro_cells: reduce number of synchronize_net() calls
- ch_ktls: release a lock before jumping to an error path
Current release - always broken:
- tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header
Previous release - regressions:
- net/tls: fix missing received data after fast remote close
- vsock/virtio: discard packets only when socket is really closed
- sock: set sk_err to ee_errno on dequeue from errq
- cxgb4: fix the panic caused by non smac rewrite
Previous release - always broken:
- tcp: fix corner cases around setting ECN with BPF selection of
congestion control
- tcp: fix race condition when creating child sockets from syncookies
on loopback interface
- usbnet: ipheth: fix connectivity with iOS 14
- tun: honor IOCB_NOWAIT flag
- net/packet: fix packet receive on L3 devices without visible hard
header
- devlink: Make sure devlink instance and port are in same net
namespace
- net: openvswitch: fix TTL decrement action netlink message format
- bonding: wait for sysfs kobject destruction before freeing struct
slave
- net: stmmac: fix upstream patch applied to the wrong context
- bnxt_en: fix return value and unwind in probe error paths
Misc:
- devlink: add extra layer of categorization to the reload stats uAPI
before it's released"
* tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
sock: set sk_err to ee_errno on dequeue from errq
mptcp: fix NULL ptr dereference on bad MPJ
net: openvswitch: fix TTL decrement action netlink message format
can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
can: mcp251xfd: mcp251xfd_probe(): bail out if no IRQ was given
can: gs_usb: fix endianess problem with candleLight firmware
ch_ktls: lock is not freed
net/tls: Protect from calling tls_dev_del for TLS RX twice
devlink: Make sure devlink instance and port are in same net namespace
devlink: Hold rtnl lock while reading netdev attributes
ptp: clockmatrix: bug fix for idtcm_strverscmp
enetc: Let the hardware auto-advance the taprio base-time of 0
gro_cells: reduce number of synchronize_net() calls
net: stmmac: fix incorrect merge of patch upstream
ipv6: addrlabel: fix possible memory leak in ip6addrlbl_net_init
Documentation: netdev-FAQ: suggest how to post co-dependent series
ibmvnic: enhance resetting status check during module exit
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+fOigeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGoQ0H/RLJU2FMIjO0mzLX
9LqePQ9QmNWG4KeqxwWaKq90MinIbnSG3CDPKruu8RNh2Rr6nsEJmqg1DWyEiFRB
8gzsBXMAC1i2aPfOrOnCJEfP+L+svKlbSii475tNdZw2DhP+/FBT0RVCt3rRhrRs
atc8+dM7ViGLnlvRJ4LlVqA3d1kjOr5bsPYcIcnGIHY8mYWBLFzTSVgDdrcB9+3l
7lZud/zMhJ3dS0bcnbIUS1YpBxHCsgEaMFQYmcv3RruIaaFbh5THkfQUSmbmrAru
/EeVjwVMuvpvb2jxS1ofLx2in7t4tsNgItu4AfMmV0BurM5NhpqKo7mo/1nmR/X9
Q4tjPRc=
=cUbb
-----END PGP SIGNATURE-----
Backmerge tag 'v5.10-rc2' into arm/drivers
The SCMI pull request for the arm/drivers branch requires v5.10-rc2
because of dependencies with other git trees, so merge that in here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
S390:
- do not reset the global diag318 data for per-cpu reset
- do not mark memory as protected too early
- fix for destroy page ultravisor call
x86:
- fix for SEV debugging
- fix incorrect return code
- fix for "noapic" with PIC in userspace and LAPIC in kernel
- fix for 5-level paging
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/BKpQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPrZgf+Jdw1ONU5hFLl5Xz2YneVppqMr3nh
X/Nr/dGzP+ve2FPNgkMotwqOWb/6jwKYKbliB2Q6fS51/7MiV7TDizna8ZpzEn12
M0/NMWtW7Luq7yTTnXUhClG4QfRvn90EaflxUYxCBSRRhDleJ9sCl4Ga5b1fDIdQ
AeDdqJV4ElCGUrPM1my4vemrbFeiiEeDeWZvb6TP5LlJS+EDZeehk9zEAB7PFwAu
oX3O8WUbRxRYakZR1PPIn8e0qh2zaVDFUk/sZKJLOCCPx2UnOErf3jV6rQEMeSPC
5aOspfq+gI3jukufdyNxcKxRSj8Jw63f0vDaUgd4H71dsG390gM6onQiQg==
=IyC5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
S390:
- do not reset the global diag318 data for per-cpu reset
- do not mark memory as protected too early
- fix for destroy page ultravisor call
x86:
- fix for SEV debugging
- fix incorrect return code
- fix for 'noapic' with PIC in userspace and LAPIC in kernel
- fix for 5-level paging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86/mmu: Fix get_mmio_spte() on CPUs supporting 5-level PT
KVM: x86: Fix split-irqchip vs interrupt injection window request
KVM: x86: handle !lapic_in_kernel case in kvm_cpu_*_extint
MAINTAINERS: Update email address for Sean Christopherson
MAINTAINERS: add uv.c also to KVM/s390
s390/uv: handle destroy page legacy interface
KVM: arm64: vgic-v3: Drop the reporting of GICR_TYPER.Last for userspace
KVM: SVM: fix error return code in svm_create_vcpu()
KVM: SVM: Fix offset computation bug in __sev_dbg_decrypt().
KVM: arm64: Correctly align nVHE percpu data
KVM: s390: remove diag318 reset code
KVM: s390: pv: Mark mm as protected after the set secure parameters and improve cleanup
This patch provides the test application for DMA_MAP_BENCHMARK.
Before running the test application, we need to bind a device to dma_map_
benchmark driver. For example, unbind "xxx" from its original driver and
bind to dma_map_benchmark:
echo dma_map_benchmark > /sys/bus/platform/devices/xxx/driver_override
echo xxx > /sys/bus/platform/drivers/xxx/unbind
echo xxx > /sys/bus/platform/drivers/dma_map_benchmark/bind
Another example for PCI devices:
echo dma_map_benchmark > /sys/bus/pci/devices/0000:00:01.0/driver_override
echo 0000:00:01.0 > /sys/bus/pci/drivers/xxx/unbind
echo 0000:00:01.0 > /sys/bus/pci/drivers/dma_map_benchmark/bind
The below command will run 16 threads on numa node 0 for 10 seconds on
the device bound to dma_map_benchmark platform_driver or pci_driver:
./dma_map_benchmark -t 16 -s 10 -n 0
dma mapping benchmark: threads:16 seconds:10
average map latency(us):1.1 standard deviation:1.9
average unmap latency(us):0.5 standard deviation:0.8
Cc: Will Deacon <will@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move HiSilicon TRNG V2 driver into 'drivers/crypto/hisilicon/trng'
with some updating on 'MAINTAINERS'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Fix SD dll reset issue by using proper macro
- Fix PM feature checking for Xilinx Versal SoC
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX70VSQAKCRDKSWXLKUoM
ISZ+AJ9IkZ3rto9BOpbuSUu2mZSG12hSBACgnY0S3UCCZ4G4RLbGrFPzvGUKTuM=
=SwId
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-fixes-for-v5.10-rc6' of https://github.com/Xilinx/linux-xlnx into arm/fixes
arm64: soc: ZynqMP SoC fixes for v5.10-rc6
- Fix SD dll reset issue by using proper macro
- Fix PM feature checking for Xilinx Versal SoC
* tag 'zynqmp-soc-fixes-for-v5.10-rc6' of https://github.com/Xilinx/linux-xlnx: (337 commits)
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
Linux 5.10-rc4
kvm: mmu: fix is_tdp_mmu_check when the TDP MMU is not in use
afs: Fix afs_write_end() when called with copied == 0 [ver #3]
ocfs2: initialize ip_next_orphan
panic: don't dump stack twice on warn
hugetlbfs: fix anon huge page migration race
mm: memcontrol: fix missing wakeup polling thread
kernel/watchdog: fix watchdog_allowed_mask not used warning
reboot: fix overflow parsing reboot cpu number
Revert "kernel/reboot.c: convert simple_strtoul to kstrtoint"
compiler.h: fix barrier_data() on clang
mm/gup: use unpin_user_pages() in __gup_longterm_locked()
mm/slub: fix panic in slab_alloc_node()
mailmap: fix entry for Dmitry Baryshkov/Eremin-Solenikov
mm/vmscan: fix NR_ISOLATED_FILE corruption on 64-bit
mm/compaction: stop isolation if too many pages are isolated and we have pages to migrate
mm/compaction: count pages and stop correctly during page isolation
drm/nouveau/kms/nv50-: Use atomic encoder callbacks everywhere
...
Link: https://lore.kernel.org/r/fd5ab967-f3cf-95fb-7947-5477ff85f97e@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the steady stream of new features coming into the subsystem
it has been clear for some time now that help is needed.
Suzuki and Leo have worked extensively on various parts of the
project and have agreed to help.
While at it add the new location for the coresight git tree.
Acked-by: Leo Yan <leo.yan@linaro.org>
Acked-by : Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201125223519.734388-1-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to XDP and some JITs, also add Brendan and Florent who have been
reviewing all my patches internally as reviewers. The patches are expected
as usual to go via the BPF tree(s) / list / merge workflows.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201125202404.1419509-1-kpsingh@chromium.org
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
-----BEGIN PGP SIGNATURE-----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=kkcj
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.11 cycle
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
* tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings:iio:adc:x-powers,axp209-adc: txt to yaml conversion
dt-bindings:iio:adc:renesas,rcar-gyroadc: txt to yaml conversion.
dt-bindings:iio:adc:atmel,sama5d2-adc: txt to yaml conversion
dt-bindings:iio:magnetometer:pni,rm3100: txt to yaml conversion.
dt-bindings:iio:magnetometer:honeywell,hmc5843: txt to yaml format conversion
dt-bindings:iio:magnetometer:bosch,bmc150_magn: txt to yaml conversion.
dt-bindings:iio:magnetometer:asahi-kasei,ak8974: txt to yaml format conversion
dt-bindings:iio:magnetometer:fsl,mag3110: txt to yaml conversion
dt-bindings:iio:light:st,vl6180: txt to yaml format conversion.
dt-bindings:iio:light:vishay,vcnl4035: txt to yaml conversion
dt-bindings:iio:light:st,uvis25: txt to yaml conversion for this UV sensor
dt-bindings:iio:light:upisemi,us51882: txt to yaml conversion.
dt-bindings:iio:light:ti,opt3001: txt to yaml conversion
dt-bindings:iio:light:maxim,max44009: txt to yaml conversion.
dt-bindings:iio:light:sharp,gp2ap020a00f: txt to yaml conversion.
dt-bindings:iio:light:capella,cm36651: txt to yaml conversion.
dt-bindings:iio:light:avago,apds9960: txt to yaml conversion
dt-bindings:iio:light:avago,apds9300: txt to yaml conversion.
dt-bindings:iio:imu:st,lsm6dsx: txt to yaml conversion
dt-bindings:iio:imu:adi,adis16480: txt to yaml conversion
...
First set of fixes for v5.10. One fix for iwlwifi kernel panic, others
less notable.
rtw88
* fix a bogus test found by clang
iwlwifi
* fix long memory reads causing soft lockup warnings
* fix kernel panic during Channel Switch Announcement (CSA)
* other smaller fixes
MAINTAINERS
* email address updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfu93zAAoJEG4XJFUm622bc3wH+wVAoqqf/lM2e99uq+Z7KgRc
HNX1ApQcjidObFBUIiXcuVPj1V8w0HXqE7r4EXznWhKu/01ch2CNaNmN5Ttwp9dA
aIhjAx5kiCp7z/kJkTRSDh1vg6WwLDQ29il8nBiveXzD+VVLfcsPlKIF+dsXFOpz
FbISvCp4j/4TNME4u6iOafdurCchdOeuHjoZGEWAWkl1wLiryow6WlTdaYou5vTt
EDNZa2px4QXb7DS1qAr0SWHBkBH6YfdIW7zDQ/zGgrCmCE3IQNdIKQGw4/K1pn1a
9KbURnI7JgO28f/8wQjzfh6vJw4XA4P/v6mHMDIcFnS0t4YHCTfkfT0YFlBtUiI=
=870O
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.10
First set of fixes for v5.10. One fix for iwlwifi kernel panic, others
less notable.
rtw88
* fix a bogus test found by clang
iwlwifi
* fix long memory reads causing soft lockup warnings
* fix kernel panic during Channel Switch Announcement (CSA)
* other smaller fixes
MAINTAINERS
* email address updates
* tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
iwlwifi: mvm: fix kernel panic in case of assert during CSA
iwlwifi: pcie: set LTR to avoid completion timeout
iwlwifi: mvm: write queue_sync_state only for sync
iwlwifi: mvm: properly cancel a session protection for P2P
iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROC
iwlwifi: sta: set max HE max A-MPDU according to HE capa
MAINTAINERS: update maintainers list for Cypress
MAINTAINERS: update Yan-Hsuan's email address
iwlwifi: pcie: limit memory read spin time
rtw88: fix fw_fifo_addr check
====================
Link: https://lore.kernel.org/r/20201123161037.C11D1C43460@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove tegra20-devfreq in order to replace it with a EMC_STAT based
devfreq driver. Previously we were going to use MC_STAT based
tegra20-devfreq driver because EMC_STAT wasn't working properly, but
now that problem is resolved. This resolves complications imposed by
the removed driver since it was depending on both EMC and MC drivers
simultaneously.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Convert the b53 DSA device tree bindings to YAML in order to allow
for automatic checking and such.
Reviewed-by: Rob Herring <robh@kernel.org>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
On OcteonTX2 platform CPT instruction enqueue and NIX
packet send are only possible via LMTST operations which
uses LDEOR instruction. This patch moves lmt flush
function from OcteonTX2 nic driver to include/linux/soc
since it will be used by OcteonTX2 CPT and NIC driver for
LMTST.
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix boot when intel iommu initialisation fails under TXT (tboot)
- Fix intel iommu compilation error when DMAR is enabled without ATS
- Temporarily update IOMMU MAINTAINERs entry
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl+3p6gQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNPowCADBKq5PBRwqIM1tmntRu5rePf/WuB1BotlJ
cUUR8dIxFDvKMeGvN4mDbn/5jjL1+TlD7sQqFh+gcWJ9tImpAMzp1ENbg71isl5o
Ej21X9YhjfiIsKpTrNGxcetCkYaR2tp8Z4/WzSQaO+IGB578dQ9VwiwSnDyFdWUb
1Qcj712ainYvKjbq4NyL80lPm9v43OV8QZ73WeelzBjE2UcDFAV0Xl4BIX8uuGtv
I1x03JfgzmzhVBmpj5HUGPsSopMDdo5K4vlcqscqSqvBY90iHD5fgRF4ZatTjR1t
PVM/1+c9vdJIWSxSt1hsB8DPtqXVOvGjzrLW/h63rxyWsISwkAq0
=DNX/
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull iommu fixes from Will Deacon:
"Two straightforward vt-d fixes:
- Fix boot when intel iommu initialisation fails under TXT (tboot)
- Fix intel iommu compilation error when DMAR is enabled without ATS
and temporarily update IOMMU MAINTAINERs entry"
* tag 'iommu-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
MAINTAINERS: Temporarily add myself to the IOMMU entry
iommu/vt-d: Fix compile error with CONFIG_PCI_ATS not set
iommu/vt-d: Avoid panic if iommu init fails in tboot system
Email from solarflare.com will stop working. Update the maintainers.
A replacement for linux-net-drivers@solarflare.com is not working yet,
for now remove it.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Link: https://lore.kernel.org/r/20201120113207.GA1605547@mh-desktop
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Getting too many false positive matches with current use
of the content regex K: and file regex N: patterns.
This patch drops file match N: and makes K: more restricted.
Some more normal F: file wildcards are added.
Notice that AF_XDP forgot to some F: files that is also
updated in this patch.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/160586238944.2808432.4401269290440394008.stgit@firesoul
can and bpf (including the strncpy_from_user fix).
Current release - regressions:
- mac80211: fix memory leak of filtered powersave frames
- mac80211: free sta in sta_info_insert_finish() on errors to avoid
sleeping in atomic context
- netlabel: fix an uninitialized variable warning added in -rc4
Previous release - regressions:
- vsock: forward all packets to the host when no H2G is registered,
un-breaking AWS Nitro Enclaves
- net: Exempt multicast addresses from five-second neighbor lifetime
requirement, decreasing the chances neighbor tables fill up
- net/tls: fix corrupted data in recvmsg
- qed: fix ILT configuration of SRC block
- can: m_can: process interrupt only when not runtime suspended
Previous release - always broken:
- page_frag: Recover from memory pressure by not recycling pages
allocating from the reserves
- strncpy_from_user: Mask out bytes after NUL terminator
- ip_tunnels: Set tunnel option flag only when tunnel metadata is
present, always setting it confuses Open vSwitch
- bpf, sockmap:
- Fix partial copy_page_to_iter so progress can still be made
- Fix socket memory accounting and obeying SO_RCVBUF
- net: Have netpoll bring-up DSA management interface
- net: bridge: add missing counters to ndo_get_stats64 callback
- tcp: brr: only postpone PROBE_RTT if RTT is < current min_rtt
- enetc: Workaround MDIO register access HW bug
- net/ncsi: move netlink family registration to a subsystem init,
instead of tying it to driver probe
- net: ftgmac100: unregister NC-SI when removing driver to avoid crash
- lan743x: prevent interrupt storm on open
- lan743x: fix freeing skbs in the wrong context
- net/mlx5e: Fix socket refcount leak on kTLS RX resync
- net: dsa: mv88e6xxx: Avoid VLAN database corruption on 6097
- fix 21 unset return codes and other mistakes on error paths,
mostly detected by the Hulk Robot
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAl+226AACgkQMUZtbf5S
IruE1w/+JX3CqJwGIqyzyhwVshNaKxmX9gAOMJzkckjEohn8932zPaNq7kbmNYqt
5QsJoou3cXjFeoIEAkQA5fqR4stTZpZMnLO+7JnxxQ0vb2YBN+tIGQRNCnmd1Q0h
u9gb5+5AdORdlmk3E7oC8v50dzQRfboJXLEEZTo2uGJwUgLlEAiqTSV2w4YDHMhL
JtgtWA/fraL0CUc2WMoxuimg9NirbRuMijsU6+d/yExzznDpdoho/qsxL+Odu1NF
hSdaKirA8B8ml0pOd/b4mj+fm4+lKyXZBfSyLx4Ki1TqluEMLzDp7gQPRnU6yyJm
AOu4zsKxx6qitOX2qLQCNlEpkQp6LA2N2Zb1orliUV3Bsq2DJRhU35FgLcghtdRP
GTRSdKHr2BvMScOZ7dQo8l4TqVc3e/khSZDRGdvpsM275Dt0JyS/l7yAWxunPqMb
+/483/s75OuBRO57ULLJ/hR02TG37g/Jv5sI0sG/7oDpGfnulinQX+fxy9izyTEM
KYl0mAPSqhb6RcjE0YXWG0rhJN6FSvc/lwPQHjq8wPSkwEdD/FTb6/eYqbXDi1ld
UTYhFpkh1PQrwct14eSScMeJqTsNKvG0VV39/uZLZCzcqa3yOY5+oTzwaCFlMsy3
a5yGGxqoh7/FTM8t1ml21is9uZ31LAQEnNTMPv69pZPwAv5G5yE=
=SRwI
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc5, including fixes from the WiFi
(mac80211), can and bpf (including the strncpy_from_user fix).
Current release - regressions:
- mac80211: fix memory leak of filtered powersave frames
- mac80211: free sta in sta_info_insert_finish() on errors to avoid
sleeping in atomic context
- netlabel: fix an uninitialized variable warning added in -rc4
Previous release - regressions:
- vsock: forward all packets to the host when no H2G is registered,
un-breaking AWS Nitro Enclaves
- net: Exempt multicast addresses from five-second neighbor lifetime
requirement, decreasing the chances neighbor tables fill up
- net/tls: fix corrupted data in recvmsg
- qed: fix ILT configuration of SRC block
- can: m_can: process interrupt only when not runtime suspended
Previous release - always broken:
- page_frag: Recover from memory pressure by not recycling pages
allocating from the reserves
- strncpy_from_user: Mask out bytes after NUL terminator
- ip_tunnels: Set tunnel option flag only when tunnel metadata is
present, always setting it confuses Open vSwitch
- bpf, sockmap:
- Fix partial copy_page_to_iter so progress can still be made
- Fix socket memory accounting and obeying SO_RCVBUF
- net: Have netpoll bring-up DSA management interface
- net: bridge: add missing counters to ndo_get_stats64 callback
- tcp: brr: only postpone PROBE_RTT if RTT is < current min_rtt
- enetc: Workaround MDIO register access HW bug
- net/ncsi: move netlink family registration to a subsystem init,
instead of tying it to driver probe
- net: ftgmac100: unregister NC-SI when removing driver to avoid
crash
- lan743x:
- prevent interrupt storm on open
- fix freeing skbs in the wrong context
- net/mlx5e: Fix socket refcount leak on kTLS RX resync
- net: dsa: mv88e6xxx: Avoid VLAN database corruption on 6097
- fix 21 unset return codes and other mistakes on error paths, mostly
detected by the Hulk Robot"
* tag 'net-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (115 commits)
fail_function: Remove a redundant mutex unlock
selftest/bpf: Test bpf_probe_read_user_str() strips trailing bytes after NUL
lib/strncpy_from_user.c: Mask out bytes after NUL terminator.
net/smc: fix direct access to ib_gid_addr->ndev in smc_ib_determine_gid()
net/smc: fix matching of existing link groups
ipv6: Remove dependency of ipv6_frag_thdr_truncated on ipv6 module
libbpf: Fix VERSIONED_SYM_COUNT number parsing
net/mlx4_core: Fix init_hca fields offset
atm: nicstar: Unmap DMA on send error
page_frag: Recover from memory pressure
net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset
mlxsw: core: Use variable timeout for EMAD retries
mlxsw: Fix firmware flashing
net: Have netpoll bring-up DSA management interface
atl1e: fix error return code in atl1e_probe()
atl1c: fix error return code in atl1c_probe()
ah6: fix error return code in ah6_input()
net: usb: qmi_wwan: Set DTR quirk for MR400
can: m_can: process interrupt only when not runtime suspended
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery
...
Alexei Starovoitov says:
====================
1) libbpf should not attempt to load unused subprogs, from Andrii.
2) Make strncpy_from_user() mask out bytes after NUL terminator, from Daniel.
3) Relax return code check for subprograms in the BPF verifier, from Dmitrii.
4) Fix several sockmap issues, from John.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
fail_function: Remove a redundant mutex unlock
selftest/bpf: Test bpf_probe_read_user_str() strips trailing bytes after NUL
lib/strncpy_from_user.c: Mask out bytes after NUL terminator.
libbpf: Fix VERSIONED_SYM_COUNT number parsing
bpf, sockmap: Avoid failures from skb_to_sgvec when skb has frag_list
bpf, sockmap: Handle memory acct if skb_verdict prog redirects to self
bpf, sockmap: Avoid returning unneeded EAGAIN when redirecting to self
bpf, sockmap: Use truesize with sk_rmem_schedule()
bpf, sockmap: Ensure SO_RCVBUF memory is observed on ingress redirect
bpf, sockmap: Fix partial copy_page_to_iter so progress can still be made
selftests/bpf: Fix error return code in run_getsockopt_test()
bpf: Relax return code check for subprograms
tools, bpftool: Add missing close before bpftool net attach exit
MAINTAINERS/bpf: Update Andrii's entry.
selftests/bpf: Fix unused attribute usage in subprogs_unused test
bpf: Fix unsigned 'datasec_id' compared with zero in check_pseudo_btf_id
bpf: Fix passing zero to PTR_ERR() in bpf_btf_printf_prepare
libbpf: Don't attempt to load unused subprog as an entry-point BPF program
====================
Link: https://lore.kernel.org/r/20201119200721.288-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Joerg is recovering from an injury, so temporarily add myself to the
IOMMU MAINTAINERS entry so that I'm more likely to get CC'd on patches
while I help to look after the tree for him.
Suggested-by: Joerg Roedel <joro@8bytes.org>
Link: https://lore.kernel.org/r/20201117100953.GR22888@8bytes.org
Signed-off-by: Will Deacon <will@kernel.org>
Adds documentation reference created by Kishon Abraham to the
MAINTAINERS list relative with the PCI endpoint subsystem section.
Link: https://lore.kernel.org/r/4fa78c7a24e8f8ec3206e1e8960dc18f505c9e29.1597695880.git.gustavo.pimentel@synopsys.com
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Most changes in uv.c are related to KVM. Involve also the KVM team
regarding changes to uv.c.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
This converts the Armel MXT touchscreen bindings to YAML format and
extends them with the following two properties:
- vdda-supply: the optional analog supply voltage
- vdd-supply: the optional digital supply voltage
Tested the schema with all in-tree users and they verify fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-2-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+DdgYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGB1sH/0B4REolPPxiQsPL
P45+a2POUU0SQK8NjkcYskQmJ6DnPKkJSXeUU8rzuI2rty5bWEzEBxdUSh064ZaM
DGxkWrdhYNaLJuceNLlanBk3vrM3KwGkaJFSKLgsEXkmH86gl33ptA8nlQVbfc+4
FK4hRZs2J6Y5YRsuzPO8nzzHWs1CThZEcwNPOeIZrAnv+/13zyP/piZ+R/2gKYwy
RVrVrzSTkTGJXotn6J17Sa02+CGv5UqdxOZFv7jimYJOmFT7KnGngNrJbh8aYWk7
vPTRUvGozh6NyYxtRI9LKGZy1yQ05Cl7N927CnFYzD235/eT7zaRDZe1e1JaIE8Z
r2yxGCM=
=ZIYP
-----END PGP SIGNATURE-----
Merge tag 'v5.9' into next
Sync up with mainline to bring in the latest DTS files.
The DLCI driver (dlci.c) implements the Frame Relay protocol. However,
we already have another newer and better implementation of Frame Relay
provided by the HDLC_FR driver (hdlc_fr.c).
The DLCI driver's implementation of Frame Relay is used by only one
hardware driver in the kernel - the SDLA driver (sdla.c).
The SDLA driver provides Frame Relay support for the Sangoma S50x devices.
However, the vendor provides their own driver (along with their own
multi-WAN-protocol implementations including Frame Relay), called WANPIPE.
I believe most users of the hardware would use the vendor-provided WANPIPE
driver instead.
(The WANPIPE driver was even once in the kernel, but was deleted in
commit 8db60bcf30 ("[WAN]: Remove broken and unmaintained Sangoma
drivers.") because the vendor no longer updated the in-kernel WANPIPE
driver.)
Cc: Mike McLagan <mike.mclagan@linux.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201114150921.685594-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Refactor GPIO library to support bias and debounce ACPI settings
The following is an automated git shortlog grouped by driver:
gpiolib:
- acpi: Make Intel GPIO tree official for GPIO ACPI work
- acpi: Use BIT() macro to increase readability
- acpi: Convert pin_index to be u16
- acpi: Extract acpi_request_own_gpiod() helper
- acpi: Make acpi_gpio_to_gpiod_flags() usable for GpioInt()
- acpi: Set initial value for output pin based on bias and polarity
- acpi: Move acpi_gpio_to_gpiod_flags() upper in the code
- acpi: Move non-critical code outside of critical section
- acpi: Take into account debounce settings
- acpi: Use named item for enum gpiod_flags variable
- acpi: Respect bias settings for GpioInt() resource
- Introduce gpio_set_debounce_timeout() for internal use
- Extract gpio_set_config_with_argument_optional() helper
- move bias related code from gpio_set_config() to gpio_set_bias()
- Extract gpio_set_config_with_argument() for future use
- use proper API to pack pin configuration parameters
- add missed break statement
- Replace unsigned by unsigned int
Merge tag 'intel-pinctrl-v5.10-2' into HEAD:
- Merge tag 'intel-pinctrl-v5.10-2' into HEAD
pinctrl:
- intel: Set default bias in case no particular value given
- intel: Fix 2 kOhm bias which is 833 Ohm
-----BEGIN PGP SIGNATURE-----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=YamF
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.11-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.11-1
* Refactor GPIO library to support bias and debounce ACPI settings
The following is an automated git shortlog grouped by driver:
gpiolib:
- acpi: Make Intel GPIO tree official for GPIO ACPI work
- acpi: Use BIT() macro to increase readability
- acpi: Convert pin_index to be u16
- acpi: Extract acpi_request_own_gpiod() helper
- acpi: Make acpi_gpio_to_gpiod_flags() usable for GpioInt()
- acpi: Set initial value for output pin based on bias and polarity
- acpi: Move acpi_gpio_to_gpiod_flags() upper in the code
- acpi: Move non-critical code outside of critical section
- acpi: Take into account debounce settings
- acpi: Use named item for enum gpiod_flags variable
- acpi: Respect bias settings for GpioInt() resource
- Introduce gpio_set_debounce_timeout() for internal use
- Extract gpio_set_config_with_argument_optional() helper
- move bias related code from gpio_set_config() to gpio_set_bias()
- Extract gpio_set_config_with_argument() for future use
- use proper API to pack pin configuration parameters
- add missed break statement
- Replace unsigned by unsigned int
Merge tag 'intel-pinctrl-v5.10-2' into HEAD:
- Merge tag 'intel-pinctrl-v5.10-2' into HEAD
pinctrl:
- intel: Set default bias in case no particular value given
- intel: Fix 2 kOhm bias which is 833 Ohm
I appreciate my time as a kernel maintainer for the last few years.
I am no longer working on the LPC32xx platform
and cannot commit time for support and discussions.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All the items in the TODO list were addressed, uapi was reviewed,
documentation written, checkpatch errors fixed, several bugs fixed.
There is no big reason to keep this driver in staging, so move it out.
Dt-bindings Verified with:
make ARCH=arm64 dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/rockchip-isp1.yaml
Fields of MAINTAINERS file sorted according to output of
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
--order
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[hverkuil: fix various checkpatch alignment warnings]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed to
'phy-mode="rgmii-id"' now, because the PHY drivers (realtek, ksz9031,
dp83867, ...) now configure the internal delay based on that when they
used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution that
would avoid breaking all boards, but that does not seem to be happening
any time soon, so I am now sending the correct version of the dts files to
ensure that at least these machines can use their network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU
operating points to match the data sheet
- A revert for a dts patch that caused a regression in USB
support on Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak
and missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent
for correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl+yqIMACgkQmmx57+YA
GNniQxAAnv8RAPMt8Jv4tyA0RshkD5+6JtgD6KfYccbI5Df+1O3YKJm90SA4Tpwg
03GHpAsgIs9SYNP7gSs9HPYCOJwC4rmgmfbnbB4Ezpr+oe+w6C8FI7160BBgb4f8
3/0LC6YyF48SPJ40lF/GOnTLbD5hxGw08oHCh/oL+b+bwn21JZoXAtkloCz8o6Ax
u98G5MAaJhoTFaE3jq+8F1t6PNJ518HTulzod7uLAjn4iQtAmE96J7q9ncwcGu6a
HNNcAGuz7X5QfEwWuAJai8eWvtMyGLvB5x1LXjjCNKgIqG+cD1tqpQ3FMedi36fg
N+fxMxTJKuvBaQ83h/yyNk4/W3h6ddTbuEH0s320xSP5eiZ4r+/2Ry3WPHxHR3Rq
YYDFbN6I19pQmgedJhgEmUEJXMcyId4SqN85l+uB58lOzu4zGf4WwVd+CBnEoIu3
wMGHbwruP1t+4hvZjiga53iOzWTR2EzTYkKxfDrV3mPZY6gmov5Xjb0JZNl164WF
0IJEa61HKf/ueJ5UNwWXpObNyD9rD2Ucugvok/KC1s06NFKjebGK4JhwChxMN0Sk
baynLGSDe8utENrYgW+KmgZTQHTEICimT5ogW7H+W3trXqxvTKpwCsv5zZM0e238
vULK/YGZLQZaZrxsCG2WylL6SlJQfptMy8wzOoKmbgTOkcsBasA=
=Qgm/
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
Martin Schiller is an active developer and reviewer for the X.25 code.
His company is providing products based on the Linux X.25 stack.
So he is a good candidate for maintainers of the X.25 code.
The original maintainer of the X.25 network layer (Andrew Hendry) has
not sent any email to the netdev mail list since 2013. So he is probably
inactive now.
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201114111029.326972-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make Intel GPIO tree official for GPIO ACPI work.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert to YAML and add generic IP core compatibles "cnm,codadx6",
"cnm,codahx4", "cnm,coda7541", and "cnm,coda960" in addition to the SoC
specific compatibles. The new generic compatibles are already used in
the SoC device trees and replace the free form comments. For example:
- compatible : should be "fsl,<chip>-src" for i.MX SoCs:
(a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27
turns into:
properties:
compatible:
oneOf:
- items:
- const: fsl,imx27-vpu
- const: cnm,codadx6
This allows to properly specify the secondary JPEG unit interrupt that
is only present on cnm,coda960.
Also add the missing "fsl,imx6dl-vpu", "cnm,coda960" compatible.
The AXI bus connection to the internal SRAM is different between i.MX6Q
and i.MX6DL, which requires the driver to load a different firmware
depending on the SoC.
Further, specify the power-domain property for i.MX6 and change the
clock order from "ahb", "per" to "per", "ahb". This order is currently
used in all SoC device trees.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I would like to contribute some of my time to co-maintain the CAMSS
driver. I'm currently working to extend CAMSS to new hardware platforms.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 754f0f1ba8 ("media: MAINTAINERS: change maintainer of the zoran
driver") added a new section in MAINTAINERS with an invalid file entry
and at the wrong place for alphabetic ordering.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:
warning: no file matches F: Documentation/media/v4l-drivers/zoran.rst
Point the file entry to the right location and move the section to the
right place in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here are some small Thunderbolt and USB driver fixes for 5.10-rc4 to
solve some reported issues.
Nothing huge in here, just small things:
- thunderbolt memory leaks fixed and new device ids added
- revert of problem patch for the musb driver
- new quirks added for USB devices
- typec power supply fixes to resolve much reported problems
about charging notifications not working anymore
All except the cdc-acm driver quirk addition have been in linux-next
with no reported issues (the quirk patch was applied on Friday, and is
self-contained.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX7E6EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymHNwCePOBlfVmcH3eEqVTByPdAG+L5m7MAnRLRqmMw
aPpNB/a0CRSPxH+5Z+nV
=Vi/z
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt fixes from Greg KH:
"Here are some small Thunderbolt and USB driver fixes for 5.10-rc4 to
solve some reported issues.
Nothing huge in here, just small things:
- thunderbolt memory leaks fixed and new device ids added
- revert of problem patch for the musb driver
- new quirks added for USB devices
- typec power supply fixes to resolve much reported problems about
charging notifications not working anymore
All except the cdc-acm driver quirk addition have been in linux-next
with no reported issues (the quirk patch was applied on Friday, and is
self-contained)"
* tag 'usb-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode
MAINTAINERS: add usb raw gadget entry
usb: typec: ucsi: Report power supply changes
xhci: hisilicon: fix refercence leak in xhci_histb_probe
Revert "usb: musb: convert to devm_platform_ioremap_resource_byname"
thunderbolt: Add support for Intel Tiger Lake-H
thunderbolt: Only configure USB4 wake for lane 0 adapters
thunderbolt: Add uaccess dependency to debugfs interface
thunderbolt: Fix memory leak if ida_simple_get() fails in enumerate_services()
thunderbolt: Add the missed ida_simple_remove() in ring_request_msix()
Remove Kamil Debski, Kyungmin Park and Jeongtae Park from maintainers of
several drivers. There were no maintenance activities from them for
some time. While at touching credits, this also cleans up white spaces.
-----BEGIN PGP SIGNATURE-----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=4wKi
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/fixes
Samsung changes for v5.10
Remove Kamil Debski, Kyungmin Park and Jeongtae Park from maintainers of
several drivers. There were no maintenance activities from them for
some time. While at touching credits, this also cleans up white spaces.
* tag 'samsung-fixes-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
CREDITS: remove trailing white spaces
MAINTAINERS: remove Jeongtae Park from Samsung MFC entry
MAINTAINERS: move Kyungmin Park to credits
MAINTAINERS: move Kamil Debski to credits
Link: https://lore.kernel.org/r/20201031120237.8542-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- net: udp: fix out-of-order packets when forwarding with UDP GSO
fraglists turned on
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter rules
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AKM7
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for
ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- fix out-of-order UDP packets when forwarding with UDP GSO fraglists
turned on:
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter
rules"
* tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
lan743x: fix use of uninitialized variable
net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO
net: udp: fix UDP header access on Fast/frag0 UDP GRO
devlink: Avoid overwriting port attributes of registered port
vrf: Fix fast path output packet handling with async Netfilter rules
cosa: Add missing kfree in error path of cosa_write
net: switch to the kernel.org patchwork instance
ch_ktls: stop the txq if reaches threshold
ch_ktls: tcb update fails sometimes
ch_ktls/cxgb4: handle partial tag alone SKBs
ch_ktls: don't free skb before sending FIN
ch_ktls: packet handling prior to start marker
ch_ktls: Correction in middle record handling
ch_ktls: missing handling of header alone
ch_ktls: Correction in trimmed_len calculation
cxgb4/ch_ktls: creating skbs causes panic
ch_ktls: Update cheksum information
ch_ktls: Correction in finding correct length
cxgb4/ch_ktls: decrypted bit is not enough
net/x25: Fix null-ptr-deref in x25_connect
...
Andrii has been a de-facto maintainer for libbpf and other components.
Update maintainers entry to acknowledge his work de-jure.
The folks with git write permissions will continue to follow the rule
of not applying their own patches unless absolutely trivial.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201112180340.45265-1-alexei.starovoitov@gmail.com
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-11-10
This series contains updates to i40e and igc drivers and the MAINTAINERS
file.
Slawomir fixes updating VF MAC addresses to fix various issues related
to reporting and setting of these addresses for i40e.
Dan Carpenter fixes a possible used before being initialized issue for
i40e.
Vinicius fixes reporting of netdev stats for igc.
Tony updates repositories for Intel Ethernet Drivers.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
MAINTAINERS: Update repositories for Intel Ethernet Drivers
igc: Fix returning wrong statistics
i40e, xsk: uninitialized variable in i40e_clean_rx_irq_zc()
i40e: Fix MAC address setting for a VF via Host/VM
====================
Link: https://lore.kernel.org/r/20201111001955.533210-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add myself to cover the Hirschmann Hellcreek TSN Ethernet Switch Driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201110071829.7467-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move to the kernel.org patchwork instance, it has significantly
lower latency for accessing from Europe and the US. Other quirks
include the reply bot.
Link: https://lore.kernel.org/r/20201110035120.642746-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds support for a basic LiteX-based SoC with a mor1kx soft CPU.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
[shorne: Merged in soc-cntl patch, removed CROSS_COMPILE, sort MAINT.]
Signed-off-by: Stafford Horne <shorne@gmail.com>
I will be maintaining the Thunderbolt DMA traffic test driver.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bodo knows the code better than me now, has time to review patches and is
excellent at it, and has lots of ideas for how to make the driver better,
so this patch adds him as the maintainer.
There was no entry in there already. Andy had posted on the list here:
https://www.spinics.net/lists/target-devel/msg14690.html
when it got transitioned to me. I added an entry because several companies
used it and I thought it would be easy for them to find Bodo.
Link: https://lore.kernel.org/r/1604521666-16573-1-git-send-email-michael.christie@oracle.com
Cc: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I am retiring soon. Thus this patch removes myself from the
MAINTAINERS file (s390 network).
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
[jwi: fix up the subject]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A check with ./scripts/get_maintainer.pl --letters -f fs/tracefs/ shows
that the tracefs is not assigned to the TRACING section in MAINTAINERS.
Add the file pattern for the TRACING section to rectify that.
Link: https://lkml.kernel.org/r/20201109122250.31915-1-lukas.bulwahn@gmail.com
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The edac_altera entry stopped at the "." and needed "[ch]" to match
both the driver and the header file.
The edac_skx entry only matched on ".c" files so didn't include skx_common.h
Signed-off-by: Tony Luck <tony.luck@intel.com>
RFC for adding a support for typical voltage scaling connection
In few occasions there has been a need to scale the voltage output
from bucks on BD71837. Usually this is done when buck8 is used to
power specific GPU which can utilize voltages down to 0.7V. As lowest
the buck8 on BD71837 can go is 0.8V, and external connection is used to
scale the voltages.
The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the
feedback pin using suitable voltage/resistors.
|---------------|
| buck 8 |-------+----->Vout
| | |
|---------------| |
| |
| |
+-------+--R2----+
|
R1
|
V FB-pull-up
This will scale the voltage as follows:
- Vout_o = Vo - (Vpu - Vo)*R2/R1
- Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
>From HW point of view this does not need to be limited to buck 8. This
connection can be used to adjust output from any of the bucks on
BD71837/47/50.
As this seems to be a 'de-facto' way to scale the voltages on BD71837 it
might be a good idea to support computing the new voltage ranges for
bucks based on the V-pull-up and resistor R1/R2 values given from
device-tree. This allows describing the external HW connection using DT
to correctly scale the voltages.
This RFC uses "rohm,feedback-pull-up-r1-ohms" and
"rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but
these names (without the picture) might not be too descriptive. I am
grateful for all suggestions as better and more descriptive names.
This patch series is an RFC because this connection feels somewhat
"hacky". OTOH - when hack becomes widely used, it is less of an hack and
more of a standard - and occasionally supporting HW hacks using SW may
benefit us all, right? :)
The other thing some projects do is allowing the change of BD71837 buck8
voltages when buck8 is enabled. This however will introduce voltage
spikes as buck8 was not originally designed for this. The specific HW
platform must be evaluated to be able to tolerate these spikes. Thus
this patch series does not support buck8 voltage changes when buck8 is
enabled. I wonder if this should be allowed per some config option(?) I
don't want to help people frying their boards... Opinions? Is there
suggested way of allowing this type of features at own risk? Config or
even Some #ifdef which is not listed in Kconfig? Device-tree property?
If you have (good) suggestions I could add the optional (non default)
DVS support for non DVS bucks on BD71837.
Matti Vaittinen (3):
dt-bindings: regulator: BD71837 support commonly used feedback
connection
dt-bindings: regulator: BD71847 support commonly used feedback
connection
regulator: bd718x7: Support external connection to scale voltages
.../regulator/rohm,bd71837-regulator.yaml | 48 +++++
.../regulator/rohm,bd71847-regulator.yaml | 49 ++++++
drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++-
3 files changed, 254 insertions(+), 7 deletions(-)
base-commit: 3cea11cd5e
--
2.21.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Take over maintainership of panasonic-laptop from Harald Welte.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Link: https://lore.kernel.org/r/20200825101341.5699-1-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+oiOgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGKBQIAJw6oad/FA7j9OO2
dMoaXb8UaBehGWgW2rdfWrFPV5v0DBnp/GkdRpLoZIjV3W4mBfnog7bIa4Eswlxo
Y8sZxo5/3JlgJQUkHvzR1TYk5z61lHkUw9Kj/cCyx6YdbjSl19AfFsnhQVVMuyp9
TXL2c7hxkHlw8eBGrymVu0Ip7Zq0x8O2g+8nQpmRcvaR6SBuSHdikDF/iWCtU1YW
wpk5eWEVaAO67keZOz6b+aCFHqjFX+1dUBBuPnslucYLR73Qi16hfaU9pebe97Gb
lX/MJ1bR9BeRp314cF0PYbm4WhKjRLudHOFJH8x3dj/BiYNrFK3SJGLiiTwsrAZ8
kytU0Xs=
=Ke/D
-----END PGP SIGNATURE-----
Merge v5.10-rc3 into drm-next
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
amd-drm-next-5.11-2020-11-05:
amdgpu:
- Add initial support for Vangogh
- Add support for Green Sardine
- Add initial support for Dimgrey Cavefish
- Scatter/Gather display support for Renoir
- Updates for Sienna Cichlid
- Updates for Navy Flounder
- SMU7 power improvements
- Modifier support for gfx9+
- CI BACO fixes
- Arcturus SMU fixes
- Lots of code cleanups
- DC fixes
- Kernel doc fixes
- Add more GPU HW client information to page fault error logging
- MPO clock tuning for RV
- FP fixes for DCN3 on ARM and PPC
radeon:
- Expose voltage via hwmon on Sumo APUs
amdkfd:
- Fix unique id handling
- Misc fixes
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105222749.201798-1-alexander.deucher@amd.com
few other miscellaneous bug fixes and a cleanup for the MAINTAINERS
file.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl+pfIoACgkQ8vlZVpUN
gaMGFAf9FP9DoKQp10zp98LphiPRzMAqt9/ghUWcpz1bkXy33+NHivEi1tOTFcrZ
hetvtOi/YnMlcD8f5IMf2vyOvj96ubI9fgsN3CIGNzU6kQm5E1s/h14PdQ2OkJbb
Kn/BpmaWcTZRj0OXt9CcnEqAYIGrRMaHgZLcDoMwOCr+WgUTJD9Sk7mMLDRBkh8u
QXnfRG2Ahsip8ZUdNTxB7fWPC8BkQAhkLnUe+9mMzIQEMDNs7kfPhnuN+ka334KV
62rc99lYvy3jWV34Iahd/pwS8VOYb0x4EHtcqD28bePy/WR9GU54bdbqMDV33bsx
D+gnQLfwgoW92+3/2TTXvpG4WPWeqQ==
=Y2bI
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes and cleanups from Ted Ts'o:
"More fixes and cleanups for the new fast_commit features, but also a
few other miscellaneous bug fixes and a cleanup for the MAINTAINERS
file"
* tag 'ext4_for_linus_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (28 commits)
jbd2: fix up sparse warnings in checkpoint code
ext4: fix sparse warnings in fast_commit code
ext4: cleanup fast commit mount options
jbd2: don't start fast commit on aborted journal
ext4: make s_mount_flags modifications atomic
ext4: issue fsdev cache flush before starting fast commit
ext4: disable fast commit with data journalling
ext4: fix inode dirty check in case of fast commits
ext4: remove unnecessary fast commit calls from ext4_file_mmap
ext4: mark buf dirty before submitting fast commit buffer
ext4: fix code documentatioon
ext4: dedpulicate the code to wait on inode that's being committed
jbd2: don't read journal->j_commit_sequence without taking a lock
jbd2: don't touch buffer state until it is filled
jbd2: add todo for a fast commit performance optimization
jbd2: don't pass tid to jbd2_fc_end_commit_fallback()
jbd2: don't use state lock during commit path
jbd2: drop jbd2_fc_init documentation
ext4: clean up the JBD2 API that initializes fast commits
jbd2: rename j_maxlen to j_total_len and add jbd2_journal_max_txn_bufs
...
AMD Power Management Controller driver a.k.a. amd-pmc driver is the
controller which is meant for the final S2Idle transaction that goes to
the PMFW running on the AMD SMU (System Management Unit) responsible for
tuning of the VDD.
Once all the monitored list or the idle constraints are met, this driver
would go and set the OS_HINT (meaning all the devices have reached to
their lowest state possible) via the SMU mailboxes.
This driver would also provide some debug capabilities via debugfs.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201105140531.2955555-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit adds driver for the FPGA-based LiteUART serial controller
from LiteX SoC builder.
The current implementation supports LiteUART configured
for 32 bit data width and 8 bit CSR bus width.
It does not support IRQ.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Conventionally, wake-up events for a specific device, in our case the
lid device, are managed via the ACPI _PRW field. While this does not
seem strictly necessary based on ACPI spec, the kernel disables GPE
wakeups to avoid non-wakeup interrupts preventing suspend by default and
only enables GPEs associated via the _PRW field with a wake-up capable
device. This behavior has been introduced in commit f941d3e41d ("ACPI:
EC / PM: Disable non-wakeup GPEs for suspend-to-idle") and is described
in more detail in its commit message.
Unfortunately, on MS Surface devices, there is no _PRW field present on
the lid device, thus no GPE is associated with it, and therefore the GPE
responsible for sending the status-change notification to the lid gets
disabled during suspend, making it impossible to wake the device via the
lid.
This patch introduces a pseudo-device and respective driver which, based
on some DMI matching, marks the corresponding GPE of the lid device for
wake and enables it during suspend. The behavior of this driver models
the behavior of the ACPI/PM core for normal wakeup GPEs, properly
declared via the _PRW field.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20201028105427.1593764-1-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----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=l+RW
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-x86-v5.11' into review-hans
Immutable branch between MFD and x86 due for the v5.11 merge window
Pull i2c fixes from Wolfram Sang:
"Driver bugfixes for I2C.
Most of them are for the new mlxbf driver which got more exposure
after rc1. The sh_mobile patch should already have reached you during
the merge window, but I accidently dropped it. However, since it fixes
a problem with rebooting, it is still fine for rc3"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: slave should do WRITE_REQUESTED before WRITE_RECEIVED
i2c: designware: call i2c_dw_read_clear_intrbits_slave() once
i2c: mlxbf: I2C_MLXBF should depend on MELLANOX_PLATFORM
i2c: mlxbf: Update author and maintainer email info
i2c: mlxbf: Update reference clock frequency
i2c: mlxbf: Remove unecessary wrapper functions
i2c: mlxbf: Fix resrticted cast warning of sparse
i2c: mlxbf: Add CONFIG_ACPI to guard ACPI function call
i2c: sh_mobile: implement atomic transfers
i2c: mediatek: move dma reset before i2c reset
fonts:
- constify font structures.
MAINTAINERS:
- Fix path for amdgpu power management
amdgpu:
- Add support for more navi1x SKUs
- Fix for suspend on CI dGPUs
- VCN DPG fix for Picasso
- Sienna Cichlid fixes
- Polaris DPM fix
- Add support for Green Sardine
amdkfd:
- Fix an allocation failure check
i915:
- Fix set domain's cache coherency
- Fixes around breadcrumbs
- Fix encoder lookup during PSR atomic
- Hold onto an explicit ref to i915_vma_work.pinned
- gvt: HWSP reset handling fix
- gvt: flush workaround
- gvt: vGPU context pin/unpin
- gvt: mmio cmd access fix for bxt/apl
imx:
- drop unused functions and callbacks
- reuse imx_drm_encoder_parse_of
- spinlock rework
- memory leak fix
- minor cleanups
vc4:
- resource cleanup fix
panfrost:
- madvise/shrinker fix
-----BEGIN PGP SIGNATURE-----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=6eUB
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2020-11-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"It's Friday here so that means another installment of drm fixes to
distract you from the counting process.
Changes all over the place, the amdgpu changes contain support for a
new GPU that is close to current one already in the tree (Green
Sardine) so it shouldn't have much side effects.
Otherwise imx has a few cleanup patches and fixes, amdgpu and i915
have around the usual smattering of fixes, fonts got constified, and
vc4/panfrost has some minor fixes. All in all a fairly regular rc3.
We have an outstanding nouveau regression, but the author is looking
into the fix, so should be here next week.
I now return you to counting.
fonts:
- constify font structures.
MAINTAINERS:
- Fix path for amdgpu power management
amdgpu:
- Add support for more navi1x SKUs
- Fix for suspend on CI dGPUs
- VCN DPG fix for Picasso
- Sienna Cichlid fixes
- Polaris DPM fix
- Add support for Green Sardine
amdkfd:
- Fix an allocation failure check
i915:
- Fix set domain's cache coherency
- Fixes around breadcrumbs
- Fix encoder lookup during PSR atomic
- Hold onto an explicit ref to i915_vma_work.pinned
- gvt: HWSP reset handling fix
- gvt: flush workaround
- gvt: vGPU context pin/unpin
- gvt: mmio cmd access fix for bxt/apl
imx:
- drop unused functions and callbacks
- reuse imx_drm_encoder_parse_of
- spinlock rework
- memory leak fix
- minor cleanups
vc4:
- resource cleanup fix
panfrost:
- madvise/shrinker fix"
* tag 'drm-fixes-2020-11-06-1' of git://anongit.freedesktop.org/drm/drm: (55 commits)
drm/amdgpu/display: remove DRM_AMD_DC_GREEN_SARDINE
drm/amd/display: Add green_sardine support to DM
drm/amd/display: Add green_sardine support to DC
drm/amdgpu: enable vcn support for green_sardine (v2)
drm/amdgpu: enable green_sardine_asd.bin loading (v2)
drm/amdgpu/sdma: add sdma engine support for green_sardine (v2)
drm/amdgpu: add gfx support for green_sardine (v2)
drm/amdgpu: add soc15 common ip block support for green_sardine (v3)
drm/amdgpu: add green_sardine support for gpu_info and ip block setting (v2)
drm/amdgpu: add Green_Sardine APU flag
drm/amdgpu: resolved ASD loading issue on sienna
amdkfd: Check kvmalloc return before memcpy
drm/amdgpu: update golden setting for sienna_cichlid
amd/amdgpu: Disable VCN DPG mode for Picasso
drm/amdgpu/swsmu: remove duplicate call to smu_set_default_dpm_table
drm/i915: Hold onto an explicit ref to i915_vma_work.pinned
drm/i915/gt: Flush xcs before tgl breadcrumbs
drm/i915/gt: Expose more parameters for emitting writes into the ring
drm/i915: Fix encoder lookup during PSR atomic check
drm/i915/gt: Use the local HWSP offset during submission
...
Correct the email addresses of the author and the maintainer
of the Mellanox BlueField I2C driver.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Update maintainers' email with Infineon hosted email
- Add Chung-hsien Hsu as a maintainer
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030085610.145679-1-chi-hsien.lin@cypress.com
amd-drm-fixes-5.10-2020-11-04:
amdgpu:
- Add support for more navi1x SKUs
- Fix for suspend on CI dGPUs
- VCN DPG fix for Picasso
- Sienna Cichlid fixes
- Polaris DPM fix
- Add support for Green Sardine
amdkfd:
- Fix an allocation failure check
MAINTAINERS:
- Fix path for amdgpu power management
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201104205741.4100-1-alexander.deucher@amd.com
An addition to MAINTAINERS plus a fix for a nasty bootstrapping problem
which caused problems when we need to read the voltage of a regulator
that is not yet available during initialization, we were not correctly
distinguishing between this case and the case where a regulator is put
into a bypass mode.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl+kBncACgkQJNaLcl1U
h9DHMQf9FzSHbhdl2h3d0quiZF88H4ukXgkHRJJeqCsVv7kTekGgui3KEB19x5+3
rATP2AMt9aF9bG9YCWt2VazrbvJQ7hSmHq9NlrbaM2UZJW/12lKJ6v33xJWSxhTl
kGPhNirbNaxZ1B4SJJiiBX59puSTbaOj9JwI9MlR+8gxqE+Mk42Qz2UHNUINB3At
g9zuHXts+Iure4D18vBZcu/Vcrs3x8HMYtYsZgskT6fgvt/AsHCQ8yYUP6sB2EIN
h7msMvAxSwAGOBcLx6wDM3azcxz5SvAr5WeoXaMrDfUMWH2TGlTuIVhq4uXqrAVu
twG4JNCLV66YE4gILSGu7FdRauOOfg==
=0T87
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"An addition to MAINTAINERS plus a fix for a nasty bootstrapping
problem which caused problems when we need to read the voltage of a
regulator that is not yet available during initialization, we were not
correctly distinguishing between this case and the case where a
regulator is put into a bypass mode"
* tag 'regulator-fix-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: defer probe when trying to get voltage from unresolved supply
MAINTAINERS: Add entry for Qualcomm IPQ4019 VQMMC regulator
Describe the two MPTCP sysctls, what the values mean, and the default
settings.
Acked-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Intel Platform Monitoring Technology is meant to provide a common way to
access telemetry and system metrics.
Register mappings are not provided by the driver. Instead, a GUID is read
from a header for each endpoint. The GUID identifies the device and is to
be used with an XML, provided by the vendor, to discover the available set
of metrics and their register mapping. This allows firmware updates to
modify the register space without needing to update the driver every time
with new mappings. Firmware writes a new GUID in this case to specify the
new mapping. Software tools with access to the associated XML file can
then interpret the changes.
The module manages access to all Intel PMT endpoints on a system,
independent of the device exporting them. It creates an intel_pmt class
to manage the devices. For each telemetry endpoint, sysfs files provide
GUID and size information as well as a pointer to the parent device the
telemetry came from. Software may discover the association between
endpoints and devices by iterating through the list in sysfs, or by looking
for the existence of the class folder under the device of interest. A
binary sysfs attribute of the same name allows software to then read or map
the telemetry space for direct access.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Platform Monitoring Technology (PMT) is an architecture for
enumerating and accessing hardware monitoring facilities. PMT supports
multiple types of monitoring capabilities. This driver creates platform
devices for each type so that they may be managed by capability specific
drivers (to be introduced). Capabilities are discovered using PCIe DVSEC
ids. Support is included for the 3 current capability types, Telemetry,
Watcher, and Crashlog. The features are available on new Intel platforms
starting from Tiger Lake for which support is added. This patch adds
support for Tiger Lake (TGL), Alder Lake (ADL), and Out-of-Band Management
Services Module (OOBMSM).
Also add a quirk mechanism for several early hardware differences and bugs.
For Tiger Lake and Alder Lake, do not support Watcher and Crashlog
capabilities since they will not be compatible with future product. Also,
fix use a quirk to fix the discovery table offset.
Co-developed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
number of warnings from the once-noisy docs build process is nearly zero.
Getting to this point has required a lot of work; once there, hopefully we
can keep things that way.
I have packaged this as a separate pull because it does a fair amount of
reaching outside of Documentation/. The changes are all in comments and in
code placement. It's all been in linux-next since last week.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl+hscQPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YgZAH/0JeDA/1VLZYYTmdABz8mjBZsoW9tyPGGztF
nsh5ykdHhL3MeTRwumW5armLVrfKhd1XT+nIzD7OcWlqu+RDOvQ5I95rahr473hP
1SHTjqm3/AlJwQoeS72X5U6QEJQ58e2IwCbP23H3x7I3Q3snEA/HhswzxurfoB/Z
j81YzDV2YPEc0LJWZ5Vn0NEdwP8cdpFv5rojsQmepq7K0yJ7tEHb7/u2cEuUBgXS
8LcYCNPLpiN+q5N8uQ5oDjIUNdLQvP03kgKtQWiCTr4BRydOrDlJie28LIedamEz
anu7UfaVK4bxn+ugRI0g2+aWQKux81ULCinKUWmLRNbcxjhaQqQ=
=hDfp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.10-warnings' of git://git.lwn.net/linux
Pull documentation build warning fixes from Jonathan Corbet:
"This contains a series of warning fixes from Mauro; once applied, the
number of warnings from the once-noisy docs build process is nearly
zero.
Getting to this point has required a lot of work; once there,
hopefully we can keep things that way.
I have packaged this as a separate pull because it does a fair amount
of reaching outside of Documentation/. The changes are all in comments
and in code placement. It's all been in linux-next since last week"
* tag 'docs-5.10-warnings' of git://git.lwn.net/linux: (24 commits)
docs: SafeSetID: fix a warning
amdgpu: fix a few kernel-doc markup issues
selftests: kselftest_harness.h: fix kernel-doc markups
drm: amdgpu_dm: fix a typo
gpu: docs: amdgpu.rst: get rid of wrong kernel-doc markups
drm: amdgpu: kernel-doc: update some adev parameters
docs: fs: api-summary.rst: get rid of kernel-doc include
IB/srpt: docs: add a description for cq_size member
locking/refcount: move kernel-doc markups to the proper place
docs: lockdep-design: fix some warning issues
MAINTAINERS: fix broken doc refs due to yaml conversion
ice: docs fix a devlink info that broke a table
crypto: sun8x-ce*: update entries to its documentation
net: phy: remove kernel-doc duplication
mm: pagemap.h: fix two kernel-doc markups
blk-mq: docs: add kernel-doc description for a new struct member
docs: userspace-api: add iommu.rst to the index file
docs: hwmon: mp2975.rst: address some html build warnings
docs: net: statistics.rst: remove a duplicated kernel-doc
docs: kasan.rst: add two missing blank lines
...
Commit e8a60aa740 ("platform/x86: Introduce support for Systems
Management Driver over WMI for Dell Systems") added a new section
DELL WMI SYSMAN DRIVERS in MAINTAINERS, but slipped in a typo.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:
warning: no file matches F: drivers/platform/x86/dell-wmi-syman/*
Point the file entry to the right location and add an entry for its
Documentation while at it.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Divya Bharathi <divya.bharathi@dell.com>
Link: https://lore.kernel.org/r/20201029114425.22520-1-lukas.bulwahn@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Like other filesystem does, we introduce a new file f2fs.h in path of
include/uapi/linux/, and move f2fs-specified ioctl interface definitions
to that file, after then, in order to use those definitions, userspace
developer only need to include the new header file rather than
copy & paste definitions from fs/f2fs/f2fs.h.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+fOigeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGoQ0H/RLJU2FMIjO0mzLX
9LqePQ9QmNWG4KeqxwWaKq90MinIbnSG3CDPKruu8RNh2Rr6nsEJmqg1DWyEiFRB
8gzsBXMAC1i2aPfOrOnCJEfP+L+svKlbSii475tNdZw2DhP+/FBT0RVCt3rRhrRs
atc8+dM7ViGLnlvRJ4LlVqA3d1kjOr5bsPYcIcnGIHY8mYWBLFzTSVgDdrcB9+3l
7lZud/zMhJ3dS0bcnbIUS1YpBxHCsgEaMFQYmcv3RruIaaFbh5THkfQUSmbmrAru
/EeVjwVMuvpvb2jxS1ofLx2in7t4tsNgItu4AfMmV0BurM5NhpqKo7mo/1nmR/X9
Q4tjPRc=
=cUbb
-----END PGP SIGNATURE-----
Merge 5.10-rc2 into staging-next
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's some small fixes for 5.10-rc2 and a big driver removal.
The fixes are for some reported issues in the interconnect and coresight
drivers, nothing major.
The "big" driver removal is the MIC drivers have been asked to be
removed as the hardware never shipped and Intel no longer wants to
maintain something that no one can use. This is welcomed by many as the
DMA usage of these drivers was "interesting" and the security people
were starting to question some issues that were starting to be found in
the codebase.
Note, one of the subsystems for this driver, the "VOP" code, will
probably come back in future kernel versions as it was looking to
potentially solve some PCIe virtualization issues that a number of other
vendors were wanting to solve. But as-is, this codebase didn't work for
anyone else so no actual functionality is being removed.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX56scw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMWQCgma6KXhD1HCox8T6fzWfp2tvCzEkAoI18n39v
8btS51MEfzk3FMZ7CP/7
=5Jsm
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes/removals from Greg KH:
"Here's some small fixes for 5.10-rc2 and a big driver removal.
The fixes are for some reported issues in the interconnect and
coresight drivers, nothing major.
The "big" driver removal is the MIC drivers have been asked to be
removed as the hardware never shipped and Intel no longer wants to
maintain something that no one can use. This is welcomed by many as
the DMA usage of these drivers was "interesting" and the security
people were starting to question some issues that were starting to be
found in the codebase.
Note, one of the subsystems for this driver, the "VOP" code, will
probably come back in future kernel versions as it was looking to
potentially solve some PCIe virtualization issues that a number of
other vendors were wanting to solve. But as-is, this codebase didn't
work for anyone else so no actual functionality is being removed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: cti: Initialize dynamic sysfs attributes
coresight: Fix uninitialised pointer bug in etm_setup_aux()
coresight: add module license
misc: mic: remove the MIC drivers
interconnect: qcom: use icc_sync state for sm8[12]50
interconnect: qcom: Ensure that the floor bandwidth value is enforced
interconnect: qcom: sc7180: Init BCMs before creating the nodes
interconnect: qcom: sdm845: Init BCMs before creating the nodes
interconnect: Aggregate before setting initial bandwidth
interconnect: qcom: sdm845: Enable keepalive for the MM1 BCM
Russell said that he is no longer using this machine, and it seems that
nobody else has in a long time, so it's time to say goodbye to it.
As this is the last platform using CONFIG_ARCH_USES_GETTIMEOFFSET,
there are some follow-up patches to remove that as well.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After I sent a fix for what appeared to be a harmless warning in
the wimax user interface code, the conclusion was that the whole
thing has most likely not been used in a very long time, and the
user interface possibly been broken since b61a5eea59 ("wimax: use
genl_register_family_with_ops()").
Using a shared branch between net-next and staging should help
coordinate patches getting submitted against it.
-----BEGIN PGP SIGNATURE-----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=PyFd
-----END PGP SIGNATURE-----
Merge tag 'wimax-staging' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into staging-next
Arnd writes:
wimax: move to staging
After I sent a fix for what appeared to be a harmless warning in
the wimax user interface code, the conclusion was that the whole
thing has most likely not been used in a very long time, and the
user interface possibly been broken since b61a5eea59 ("wimax: use
genl_register_family_with_ops()").
Using a shared branch between net-next and staging should help
coordinate patches getting submitted against it.
* tag 'wimax-staging' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground:
wimax: move out to staging
wimax: fix duplicate initializer warning
commit e098bc9612 ("drm/amd/pm: optimize the power related source code layout")
moved the directory, update the F: file pattern to match.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit e098bc9612 ("drm/amd/pm: optimize the power related source code layout")
moved the directory, update the F: file pattern to match.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are no known users of this driver as of October 2020, and it will
be removed unless someone turns out to still need it in future releases.
According to https://en.wikipedia.org/wiki/List_of_WiMAX_networks, there
have been many public wimax networks, but it appears that many of these
have migrated to LTE or discontinued their service altogether.
As most PCs and phones lack WiMAX hardware support, the remaining
networks tend to use standalone routers. These almost certainly
run Linux, but not a modern kernel or the mainline wimax driver stack.
NetworkManager appears to have dropped userspace support in 2015
https://bugzilla.gnome.org/show_bug.cgi?id=747846, the
www.linuxwimax.org
site had already shut down earlier.
WiMax is apparently still being deployed on airport campus networks
("AeroMACS"), but in a frequency band that was not supported by the old
Intel 2400m (used in Sandy Bridge laptops and earlier), which is the
only driver using the kernel's wimax stack.
Move all files into drivers/staging/wimax, including the uapi header
files and documentation, to make it easier to remove it when it gets
to that. Only minimal changes are made to the source files, in order
to make it possible to port patches across the move.
Also remove the MAINTAINERS entry that refers to a broken mailing
list and website.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Suggested-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kyungmin Park maintained and contributed to some of the upstreamed
S5Pv210 and Exynos4210 machines - as described in commit 10ffa96407
("MAINTAINERS: add maintainer of Samsung Mobile Machine support").
However the entry in maintainers got slightly twisted by
commit 004bbd3c01 ("MAINTAINERS: remove non existent files") -
the directory matching pattern was changed from specific machines to
the entire S5Pv210.
Anyway since long time, all S5Pv210 maintenance is covered by the
Samsung ARM architectures maintainer entry and Krzysztof Kozlowski, so
move Kyungmin Park to the CREDITS.
There was also no activity on LKML regarding other maintained drivers:
https://lore.kernel.org/lkml/?q=f%3A%22Kyungmin+Park%22
Dear Kyungmin Park, thank you for all the effort you put in to the
upstream Samsung support.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Link: https://lore.kernel.org/r/20201016151528.7553-1-krzk@kernel.org
Kamil Debski has not been active on LKML since 2017:
https://lore.kernel.org/lkml/?q=f%3A%22Kamil+Debski%22
Move Kamil Debski to the CREDITS file. Thank you for the effort you put
in to the upstream Linux kernel work.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Kamil Debski <kamil@wypas.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20201016151528.7553-1-krzk@kernel.org
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell WMI Systems Management Driver provides a sysfs
interface for systems management to enable BIOS configuration
capability on certain Dell Systems.
This driver allows user to configure Dell systems with a
uniform common interface. To facilitate this, the patch
introduces a generic way for driver to be able to create
configurable BIOS Attributes available in Setup (F2) screen.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: mark gross <mgross@linux.intel.com>
Co-developed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Co-developed-by: Prasanth KSR <prasanth.ksr@dell.com>
Signed-off-by: Prasanth KSR <prasanth.ksr@dell.com>
Signed-off-by: Divya Bharathi <divya.bharathi@dell.com>
Link: https://lore.kernel.org/r/20201027134944.316730-1-divya.bharathi@dell.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the Surface Pro 3 Button driver from platform/x86 to the newly
created platform/surface directory.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Chen Yu <yu.c.chen@intel.com>
Link: https://lore.kernel.org/r/20201009141128.683254-6-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It may make sense to split the Microsoft Surface hardware platform
drivers out to a separate subdirectory, since some of it may be shared
between ARM and x86 in the future (regarding devices like the Surface
Pro X).
Further, newer Surface devices will require additional platform drivers
for fundamental support (mostly regarding their embedded controller),
which may also warrant this split from a size perspective.
This commit introduces a new platform/surface subdirectory for the
Surface device family, with subsequent commits moving existing Surface
drivers over from platform/x86.
A new MAINTAINERS entry is added for this directory. Patches to files in
this directory will be taken up by the platform-drivers-x86 team (i.e.
Hans de Goede and Mark Gross) after they have been reviewed by
Maximilian Luz.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201009141128.683254-2-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
UV platforms are the only ones which currently use the XP/XPC/XPNET
driver, so it seems fair HPE should take some responsibility as
maintainers of it; so add Mike Travis and Steve Wahl. Cliff Whickman's
email address is no longer valid, so remove it. Robin Holt was contacted
and wishes to remain as a maintainer.
Update Dimitri Sivanich's email address for the SGI GRU driver.
Add Mike Travis to HPE Superdome Flex (UV) platform.
[ bp: Massage commit message. ]
Acked-by: Robin Holt <robinmholt@gmail.com>
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201019203533.GA1203217@swahl-home.5wahls.com
Jernej has helped a lot by reviewing patches recently, so let's make it
official.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201009074423.10708-1-maxime@cerno.tech
The old wiki page unfortunately got lost by server crash.
The new wiki can be found on the kernel.org infrastructure
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20201020152639.21950-1-matthias.bgg@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Sangbeom Kim upstreamed the Samsung SoC Sound and PMIC (MFD, regulator,
RTC) drivers. However his contributions and LKML activity ends in 2014:
https://lore.kernel.org/lkml/?q=f%3A%22Sangbeom+Kim%22
Move Sangbeom Kim to the CREDITS file. Thank you for the effort you put
in to the upstream Samsung support.
Link: https://lore.kernel.org/r/20201016061848.6258-2-krzk@kernel.org
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kukjin Kim has been maintaining the Samsung ARM architectures since 2010
up to 2016. He contributed many patches for the S3C, S5P and Exynos
support. However since 2016 there is little activity from him on the
LKML [1] so move his name to the CREDITS.
Dear Kukjin, thank you for all the effort you put in to the upstream
Samsung support.
[1] https://lore.kernel.org/lkml/?q=f%3A%22Kukjin+Kim%22
Link: https://lore.kernel.org/r/20201016061848.6258-1-krzk@kernel.org
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I am leaving Socionext. Orphan the UniPhier platform and Denali NAND
driver until somebody takes the role.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ION android code has long been marked to be removed, now that we
dma-buf support merged into the real part of the kernel.
It was thought that we could wait to remove the ion kernel at a later
time, but as the out-of-tree Android fork of the ion code has diverged
quite a bit, and any Android device using the ion interface uses that
forked version and not this in-tree version, the in-tree copy of the
code is abandonded and not used by anyone.
Combine this abandoned codebase with the need to make changes to it in
order to keep the kernel building properly, which then causes merge
issues when merging those changes into the out-of-tree Android code, and
you end up with two different groups of people (the in-kernel-tree
developers, and the Android kernel developers) who are both annoyed at
the current situation. Because of this problem, just drop the in-kernel
copy of the ion code now, as it's not used, and is only causing problems
for everyone involved.
Cc: "Arve Hjønnevåg" <arve@android.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Christian Brauner <christian@brauner.io>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hridya Valsaraju <hridya@google.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Laura Abbott <laura@labbott.name>
Cc: Martijn Coenen <maco@android.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Todd Kjos <tkjos@android.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200827123627.538189-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
- Move the AVS drivers to new platform-specific locations and get
rid of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra).
-----BEGIN PGP SIGNATURE-----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=TFKg
-----END PGP SIGNATURE-----
Merge tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"First of all, the adaptive voltage scaling (AVS) drivers go to new
platform-specific locations as planned (this part was reported to have
merge conflicts against the new arm-soc updates in linux-next).
In addition to that, there are some fixes (intel_idle, intel_pstate,
RAPL, acpi_cpufreq), the addition of on/off notifiers and idle state
accounting support to the generic power domains (genpd) code and some
janitorial changes all over.
Specifics:
- Move the AVS drivers to new platform-specific locations and get rid
of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra)"
* tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
PM: sleep: remove unreachable break
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
PM: domains: Fix build error for genpd notifiers
powercap: Fix typo in Kconfig "Plance" -> "Plane"
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
PM: domains: enable domain idle state accounting
PM: domains: Add curly braces to delimit comment + statement block
PM: domains: Add support for PM domain on/off notifiers for genpd
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
...
Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late
in the 5.9 cycle started depending on a return code from
a function which changed with the 5.10 PR from the usb subsystem
Current release - regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous releases - regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu()
to synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems;
the property is not populated correctly by the firmware,
but firmware configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is
light and only wants to schedule napi (and do so through
a _irqoff() variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ceke
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
A very quiet cycle, no new features.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+QSnEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpvzoIAIAJPV0OTShpvv8JXmBDngDGysuAcQah+d3u
g2vDzRb9J3lYH7hJgkHans/4s3wYtWcJei7tgU2UkSODTSPK/l+hp4sTuVowsqPD
Cvp6k7/ipzJscl2AAiflSn5gBUORHXU8oxEeDvUAJbVkSwWdKvKgvDGPbVxZCU0V
kGlUctRq96e/TQCNekVthZ1Q4cgPKgx4zMFZjLSbj0yDN2JJJp+0Y+y5NJ5u9eTE
VneaFZOJxlhjmNZZP1Bu/MOcvgPbjxZjDRRUP75sv8c7IkoGiubHbbwcDhbE5gVd
Ve/ByiFTJe9ydKVVLm1O81AqO7uB13W46LjF5yotyk/dKX6s5eU=
=1Gdh
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"vhost, vdpa, and virtio cleanups and fixes
A very quiet cycle, no new features"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
MAINTAINERS: add URL for virtio-mem
vhost_vdpa: remove unnecessary spin_lock in vhost_vring_call
vringh: fix __vringh_iov() when riov and wiov are different
vdpa/mlx5: Setup driver only if VIRTIO_CONFIG_S_DRIVER_OK
s390: virtio: PV needs VIRTIO I/O device protection
virtio: let arch advertise guest's memory access restrictions
vhost_vdpa: Fix duplicate included kernel.h
vhost: reduce stack usage in log_used
virtio-mem: Constify mem_id_table
virtio_input: Constify id_table
virtio-balloon: Constify id_table
vdpa/mlx5: Fix failure to bring link up
vdpa/mlx5: Make use of a specific 16 bit endianness API
* pm-avs:
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
* pm-cpufreq:
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
cpufreq: Improve code around unlisted freq check
* pm-cpuidle:
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
- Support 'make compile_commands.json' to generate the compilation
database more easily, avoiding stale entries
- Support 'make clang-analyzer' and 'make clang-tidy' for static checks
using clang-tidy
- Preprocess scripts/modules.lds.S to allow CONFIG options in the module
linker script
- Drop cc-option tests from compiler flags supported by our minimal
GCC/Clang versions
- Use always 12-digits commit hash for CONFIG_LOCALVERSION_AUTO=y
- Use sha1 build id for both BFD linker and LLD
- Improve deb-pkg for reproducible builds and rootless builds
- Remove stale, useless scripts/namespace.pl
- Turn -Wreturn-type warning into error
- Fix build error of deb-pkg when CONFIG_MODULES=n
- Replace 'hostname' command with more portable 'uname -n'
- Various Makefile cleanups
-----BEGIN PGP SIGNATURE-----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=tZRN
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Support 'make compile_commands.json' to generate the compilation
database more easily, avoiding stale entries
- Support 'make clang-analyzer' and 'make clang-tidy' for static checks
using clang-tidy
- Preprocess scripts/modules.lds.S to allow CONFIG options in the
module linker script
- Drop cc-option tests from compiler flags supported by our minimal
GCC/Clang versions
- Use always 12-digits commit hash for CONFIG_LOCALVERSION_AUTO=y
- Use sha1 build id for both BFD linker and LLD
- Improve deb-pkg for reproducible builds and rootless builds
- Remove stale, useless scripts/namespace.pl
- Turn -Wreturn-type warning into error
- Fix build error of deb-pkg when CONFIG_MODULES=n
- Replace 'hostname' command with more portable 'uname -n'
- Various Makefile cleanups
* tag 'kbuild-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
kbuild: Use uname for LINUX_COMPILE_HOST detection
kbuild: Only add -fno-var-tracking-assignments for old GCC versions
kbuild: remove leftover comment for filechk utility
treewide: remove DISABLE_LTO
kbuild: deb-pkg: clean up package name variables
kbuild: deb-pkg: do not build linux-headers package if CONFIG_MODULES=n
kbuild: enforce -Werror=return-type
scripts: remove namespace.pl
builddeb: Add support for all required debian/rules targets
builddeb: Enable rootless builds
builddeb: Pass -n to gzip for reproducible packages
kbuild: split the build log of kallsyms
kbuild: explicitly specify the build id style
scripts/setlocalversion: make git describe output more reliable
kbuild: remove cc-option test of -Werror=date-time
kbuild: remove cc-option test of -fno-stack-check
kbuild: remove cc-option test of -fno-strict-overflow
kbuild: move CFLAGS_{KASAN,UBSAN,KCSAN} exports to relevant Makefiles
kbuild: remove redundant CONFIG_KASAN check from scripts/Makefile.kasan
kbuild: do not create built-in objects for external module builds
...
- New fsl-mc vfio bus driver supporting userspace drivers of objects
within NXP's DPAA2 architecture (Diana Craciun)
- Support for exposing zPCI information on s390 (Matthew Rosato)
- Fixes for "detached" VFs on s390 (Matthew Rosato)
- Fixes for pin-pages and dma-rw accesses (Yan Zhao)
- Cleanups and optimize vconfig regen (Zenghui Yu)
- Fix duplicate irq-bypass token registration (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=LDPo
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.10-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- New fsl-mc vfio bus driver supporting userspace drivers of objects
within NXP's DPAA2 architecture (Diana Craciun)
- Support for exposing zPCI information on s390 (Matthew Rosato)
- Fixes for "detached" VFs on s390 (Matthew Rosato)
- Fixes for pin-pages and dma-rw accesses (Yan Zhao)
- Cleanups and optimize vconfig regen (Zenghui Yu)
- Fix duplicate irq-bypass token registration (Alex Williamson)
* tag 'vfio-v5.10-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
vfio iommu type1: Fix memory leak in vfio_iommu_type1_pin_pages
vfio/pci: Clear token on bypass registration failure
vfio/fsl-mc: fix the return of the uninitialized variable ret
vfio/fsl-mc: Fix the dead code in vfio_fsl_mc_set_irq_trigger
vfio/fsl-mc: Fixed vfio-fsl-mc driver compilation on 32 bit
MAINTAINERS: Add entry for s390 vfio-pci
vfio-pci/zdev: Add zPCI capabilities to VFIO_DEVICE_GET_INFO
vfio/fsl-mc: Add support for device reset
vfio/fsl-mc: Add read/write support for fsl-mc devices
vfio/fsl-mc: trigger an interrupt via eventfd
vfio/fsl-mc: Add irq infrastructure for fsl-mc devices
vfio/fsl-mc: Added lock support in preparation for interrupt handling
vfio/fsl-mc: Allow userspace to MMAP fsl-mc device MMIO regions
vfio/fsl-mc: Implement VFIO_DEVICE_GET_REGION_INFO ioctl call
vfio/fsl-mc: Implement VFIO_DEVICE_GET_INFO ioctl
vfio/fsl-mc: Scan DPRC objects on vfio-fsl-mc driver bind
vfio: Introduce capability definitions for VFIO_DEVICE_GET_INFO
s390/pci: track whether util_str is valid in the zpci_dev
s390/pci: stash version in the zpci_dev
vfio/fsl-mc: Add VFIO framework skeleton for fsl-mc devices
...
has the same arguments as READ but allows the server to return an array
of data and hole extents.
Otherwise it's a lot of cleanup and bugfixes.
-----BEGIN PGP SIGNATURE-----
iQJJBAABCAAzFiEEYtFWavXG9hZotryuJ5vNeUKO4b4FAl+Q5vsVHGJmaWVsZHNA
ZmllbGRzZXMub3JnAAoJECebzXlCjuG+DUAP/RlALnXbaoWi8YCcEcc9U1LoQKbD
CJpDR+FqCOyGwRuzWung/5pvkOO50fGEeAroos+2rF/NgRkQq8EFr9AuBhNOYUFE
IZhWEOfu/r2ukXyBmcu21HGcWLwPnyJehvjuzTQW2wOHlBi/sdoL5Ap1sVlwVLj5
EZ5kqJLD+ioG2sufW99Spi55l1Cy+3Y0IhLSWl4ZAE6s8hmFSYAJZFsOeI0Afx57
USPTDRaeqjyEULkb+f8IhD0eRApOUo4evDn9dwQx+of7HPa1CiygctTKYwA3hnlc
gXp2KpVA1REaiYVgOPwYlnqBmJ2K9X0wCRzcWy2razqEcVAX/2j7QCe9M2mn4DC8
xZ2q4SxgXu9yf0qfUSVnDxWmP6ipqq7OmsG0JXTFseGKBdpjJY1qHhyqanVAGvEg
I+xHnnWfGwNCftwyA3mt3RfSFPsbLlSBIMZxvN4kn8aVlqszGITOQvTdQcLYA6kT
xWllBf4XKVXMqF0PzerxPDmfzBfhx6b1VPWOIVcu7VLBg3IXoEB2G5xG8MUJiSch
OUTCt41LUQkerQlnzaZYqwmFdSBfXJefmcE/x/vps4VtQ/fPHX1jQyD7iTu3HfSP
bRlkKHvNVeTodlBDe/HTPiTA99MShhBJyvtV5wfzIqwjc1cNreed+ePppxn8mxJi
SmQ2uZk/MpUl7/V0
=rcOj
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.10' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"The one new feature this time, from Anna Schumaker, is READ_PLUS,
which has the same arguments as READ but allows the server to return
an array of data and hole extents.
Otherwise it's a lot of cleanup and bugfixes"
* tag 'nfsd-5.10' of git://linux-nfs.org/~bfields/linux: (43 commits)
NFSv4.2: Fix NFS4ERR_STALE error when doing inter server copy
SUNRPC: fix copying of multiple pages in gss_read_proxy_verf()
sunrpc: raise kernel RPC channel buffer size
svcrdma: fix bounce buffers for unaligned offsets and multiple pages
nfsd: remove unneeded break
net/sunrpc: Fix return value for sysctl sunrpc.transports
NFSD: Encode a full READ_PLUS reply
NFSD: Return both a hole and a data segment
NFSD: Add READ_PLUS hole segment encoding
NFSD: Add READ_PLUS data support
NFSD: Hoist status code encoding into XDR encoder functions
NFSD: Map nfserr_wrongsec outside of nfsd_dispatch
NFSD: Remove the RETURN_STATUS() macro
NFSD: Call NFSv2 encoders on error returns
NFSD: Fix .pc_release method for NFSv2
NFSD: Remove vestigial typedefs
NFSD: Refactor nfsd_dispatch() error paths
NFSD: Clean up nfsd_dispatch() variables
NFSD: Clean up stale comments in nfsd_dispatch()
NFSD: Clean up switch statement in nfsd_dispatch()
...
The avs drivers are all SoC specific drivers that doesn't share any code.
Instead they are located in a directory, mostly to keep similar
functionality together. From a maintenance point of view, it makes better
sense to collect SoC specific drivers like these, into the SoC specific
directories.
Therefore, let's move the qcom-cpr driver to the qcom directory.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <nks@flawful.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
Let's add the status/info page, which is still under construction, however,
already contains valuable documentation/information.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200617104756.6312-1-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
power-supply core:
* Add wireless type
* Properly document current direction
battery/charger driver changes:
* New fuel-gauge/charger driver for RN5T618/RN5T619
* New charger driver for BQ25980, BQ25975 and BQ25960
* bq27xxx-battery: add support for TI bq34z100
* gpio-charger: convert to GPIO descriptors
* gpio-charger: add optional support for charge current limiting
* max17040: add support for max17041, max17043, max17044
* max17040: add support for max17048, max17049, max17058, max17059
* smb347-charger: add DT support
* smb247-charger: add SMB345 and SMB358 support
* simple-battery: add temperature properties
* lots of minor fixes, cleanups and DT binding YAML conversions
reset drivers:
* ocelot: Add support for Sparx5
-----BEGIN PGP SIGNATURE-----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=QtfI
-----END PGP SIGNATURE-----
Merge tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- add wireless type
- properly document current direction
Battery/charger driver changes:
- new fuel-gauge/charger driver for RN5T618/RN5T619
- new charger driver for BQ25980, BQ25975 and BQ25960
- bq27xxx-battery: add support for TI bq34z100
- gpio-charger: convert to GPIO descriptors
- gpio-charger: add optional support for charge current limiting
- max17040: add support for max17041, max17043, max17044
- max17040: add support for max17048, max17049, max17058, max17059
- smb347-charger: add DT support
- smb247-charger: add SMB345 and SMB358 support
- simple-battery: add temperature properties
- lots of minor fixes, cleanups and DT binding YAML conversions
Reset drivers:
- ocelot: Add support for Sparx5"
* tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (81 commits)
power: reset: POWER_RESET_OCELOT_RESET should depend on Ocelot or Sparx5
power: supply: bq25980: Fix uninitialized wd_reg_val and overrun
power: supply: ltc2941: Fix ptr to enum cast
power: supply: test-power: revise parameter printing to use sprintf
power: supply: charger-manager: fix incorrect check on charging_duration_ms
power: supply: max17040: Fix ptr to enum cast
power: supply: bq25980: Fix uninitialized wd_reg_val
power: supply: bq25980: remove redundant zero check on ret
power: reset: ocelot: Add support for Sparx5
dt-bindings: reset: ocelot: Add Sparx5 support
power: supply: sbs-battery: keep error code when get_property() fails
power: supply: bq25980: Add support for the BQ259xx family
dt-binding: bq25980: Add the bq25980 flash charger
power: supply: fix spelling mistake "unprecise" -> "imprecise"
power: supply: test_power: add missing newlines when printing parameters by sysfs
power: supply: pm2301: drop duplicated i2c_device_id
power: supply: charger-manager: drop unused charger assignment
power: supply: rt9455: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: goldfish: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: bq25890: skip 'struct acpi_device_id' when !CONFIG_ACPI
...
- Drop support for EZChip NPS platform
- miscll other fixes
-----BEGIN PGP SIGNATURE-----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=6IKf
-----END PGP SIGNATURE-----
Merge tag 'arc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"The bulk of ARC pull request is removal of EZChip NPS platform which
was suffering from constant bitrot. In recent years EZChip has gone
though multiple successive acquisitions and I guess things and people
move on. I would like to take this opportunity to recognize and thank
all those good folks (Gilad, Noam, Ofer...) for contributing major
bits to ARC port (SMP, Big Endian).
Summary:
- drop support for EZChip NPS platform
- misc other fixes"
* tag 'arc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: include/asm: fix typos of "themselves"
ARC: SMP: fix typo and use "come up" instead of "comeup"
ARC: [dts] fix the errors detected by dtbs_check
arc: plat-hsdk: fix kconfig dependency warning when !RESET_CONTROLLER
ARC: [plat-eznps]: Drop support for EZChip NPS platform
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCX4n0/gAKCRDh3BK/laaZ
PM3jAP4xhaix0j/y3VyaxsUqWg6ZSrjq6X0o9clGMJv27IAtjgD/fJ7ZwzTldojD
qb7N3utjLiPVRjwFmvsZ8JZ7O7PbwQ0=
=oUbZ
-----END PGP SIGNATURE-----
Merge tag 'fuse-update-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
- Support directly accessing host page cache from virtiofs. This can
improve I/O performance for various workloads, as well as reducing
the memory requirement by eliminating double caching. Thanks to Vivek
Goyal for doing most of the work on this.
- Allow automatic submounting inside virtiofs. This allows unique
st_dev/ st_ino values to be assigned inside the guest to files
residing on different filesystems on the host. Thanks to Max Reitz
for the patches.
- Fix an old use after free bug found by Pradeep P V K.
* tag 'fuse-update-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: (25 commits)
virtiofs: calculate number of scatter-gather elements accurately
fuse: connection remove fix
fuse: implement crossmounts
fuse: Allow fuse_fill_super_common() for submounts
fuse: split fuse_mount off of fuse_conn
fuse: drop fuse_conn parameter where possible
fuse: store fuse_conn in fuse_req
fuse: add submount support to <uapi/linux/fuse.h>
fuse: fix page dereference after free
virtiofs: add logic to free up a memory range
virtiofs: maintain a list of busy elements
virtiofs: serialize truncate/punch_hole and dax fault path
virtiofs: define dax address space operations
virtiofs: add DAX mmap support
virtiofs: implement dax read/write operations
virtiofs: introduce setupmapping/removemapping commands
virtiofs: implement FUSE_INIT map_alignment field
virtiofs: keep a list of free dax memory ranges
virtiofs: add a mount option to enable dax
virtiofs: set up virtio_fs dax_device
...
Pull RCU changes from Ingo Molnar:
- Debugging for smp_call_function()
- RT raw/non-raw lock ordering fixes
- Strict grace periods for KASAN
- New smp_call_function() torture test
- Torture-test updates
- Documentation updates
- Miscellaneous fixes
[ This doesn't actually pull the tag - I've dropped the last merge from
the RCU branch due to questions about the series. - Linus ]
* tag 'core-rcu-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
smp: Make symbol 'csd_bug_count' static
kernel/smp: Provide CSD lock timeout diagnostics
smp: Add source and destination CPUs to __call_single_data
rcu: Shrink each possible cpu krcp
rcu/segcblist: Prevent useless GP start if no CBs to accelerate
torture: Add gdb support
rcutorture: Allow pointer leaks to test diagnostic code
rcutorture: Hoist OOM registry up one level
refperf: Avoid null pointer dereference when buf fails to allocate
rcutorture: Properly synchronize with OOM notifier
rcutorture: Properly set rcu_fwds for OOM handling
torture: Add kvm.sh --help and update help message
rcutorture: Add CONFIG_PROVE_RCU_LIST to TREE05
torture: Update initrd documentation
rcutorture: Replace HTTP links with HTTPS ones
locktorture: Make function torture_percpu_rwsem_init() static
torture: document --allcpus argument added to the kvm.sh script
rcutorture: Output number of elapsed grace periods
rcutorture: Remove KCSAN stubs
rcu: Remove unused "cpu" parameter from rcu_report_qs_rdp()
...
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
-----BEGIN PGP SIGNATURE-----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=26wi
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make usage
of usage of 16byte load/stores possible
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=Aa/Q
-----END PGP SIGNATURE-----
Merge tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make use
of 16byte load/stores possible
- cleanups and fixes
* tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (92 commits)
MIPS: DEC: Restore bootmem reservation for firmware working memory area
MIPS: dec: fix section mismatch
bcm963xx_tag.h: fix duplicated word
mips: ralink: enable zboot support
MIPS: ingenic: Remove CPU_SUPPORTS_HUGEPAGES
MIPS: cpu-probe: remove MIPS_CPU_BP_GHIST option bit
MIPS: cpu-probe: introduce exclusive R3k CPU probe
MIPS: cpu-probe: move fpu probing/handling into its own file
MIPS: replace add_memory_region with memblock
MIPS: Loongson64: Clean up numa.c
MIPS: Loongson64: Select SMP in Kconfig to avoid build error
mips: octeon: Add Ubiquiti E200 and E220 boards
MIPS: SGI-IP28: disable use of ll/sc in kernel
MIPS: tx49xx: move tx4939_add_memory_regions into only user
MIPS: pgtable: Remove used PAGE_USERIO define
MIPS: alchemy: Share prom_init implementation
MIPS: alchemy: Fix build breakage, if TOUCHSCREEN_WM97XX is disabled
MIPS: process: include exec.h header in process.c
MIPS: process: Add prototype for function arch_dup_task_struct
MIPS: idle: Add prototype for function check_wait
...
Daniel Palmer