The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In addition to checking for potentially unnecessary iomem
readX()/writeX() operations, a pci_channel_io_perm_failure should
not trigger a full internal removal. Found during additional
testing with pSeries blade systems.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the routines can/will use resources such as devices and
rports that aren't valid after midlayer tear-down, correct this
potential race, by stopping the offending during the early stages
of the remove() callback.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As all commands queued on the physical HBA should be aborted and
returned to the upper-layers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs use this data to configure FCF information.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code used an overabundance of indirect pointers to
function helpers. Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The value is already pre-assigned prior to the qla2x00_mem_alloc().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
QLA_* return codes are 'int' in size. There were still several
legacy check-points which assumed a return-code width of 8-bits.
This could cause incorrect assumptions of 'good' status if a
return of QLA_FUNCTION_TIMEOUT.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeremy Higdon noted
(http://marc.info/?l=linux-scsi&m=123262143131788&w=2) that the
rework done in commit e315cd28b9
was not setting the proper consistent and streaming DMA masks
prior to memory allocations. Correct this and remove the
unnecessary prototype.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 73208dfd7a (qla2xxx: add
support for multi-queue adapter) inadvertently backed-out the fix
in 5bff55db3d (qla2xxx: Return a
FAILED status when abort mailbox-command fails.).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After restarting ISP the additional queues are not being setup correctly. The
following patch fixes the issue.
Please apply.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Codes to support new FCoE boards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ROMs in recent ISPs have MSI-X support, so it's no longer
necessary for the driver to fallback to interrupt polling during
ISP re-initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following patch changes the handling of bus reset when issued from a
vport. In the bus reset code, an extra check is made to make sure that the lip
reset is not done before resetting the targets if the bus reset came from a
vport.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_probe_one':
drivers/scsi/qla2xxx/qla_os.c:1582: warning: 'mem_only' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Outstanding commands are based on a request queue, scsi_qla_host
does not maintain it anymore.
2. start_scsi is accessed via isp_ops struct instead of direct
invocation.
3. Interrupt registrations are done using response queue instead of
device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed. By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: Tomasz Czernecki <czernecki@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the fcport is not online then we do not want to block IO to all ports on
the host. We just want to stop IO on port not online, so we should be using
the SCSI_MLQUEUE_TARGET_BUSY return value.
For the case where we race with the rport memset initialization
we do not want the queuecommand to be called again so we can just use
SCSI_MLQUEUE_TARGET_BUSY for this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Josip Rodin noted
(http://article.gmane.org/gmane.linux.ports.sparc/10152) the
driver oopsing during registration of an rport to the
FC-transport layer with a backtrace indicating a dereferencing of
an shost->shost_data equal to NULL. David Miller identified a
small window in driver logic where this could happen:
> Look at how the driver registers the IRQ handler before the host has
> been registered with the SCSI layer.
>
> That leads to a window of time where the shost hasn't been setup
> fully, yet ISRs can come in and trigger DPC thread events, such as
> loop resyncs, which expect the transport area to be setup.
>
> But it won't be setup, because scsi_add_host() hasn't finished yet.
>
> Note that in Josip's crash log, we don't even see the
>
> qla_printk(KERN_INFO, ha, "\n"
> " QLogic Fibre Channel HBA Driver: %s\n"
> " QLogic %s - %s\n"
> " ISP%04X: %s @ %s hdma%c, host#=%ld, fw=%s\n",
> ...
>
> message yet.
>
> Which means that the crash occurs between qla2x00_request_irqs()
> and printing that message.
Close this window by enabling RISC interrupts after the host has
been registered with the SCSI midlayer.
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During internal testing, we've seen issues (hangs) with the
'deferred' vport tear-down-processing typically accompanied with
the fc_remove_host() call. This is due to the current
implementation's back-end vport handling being performed by the
physical-HA's DPC thread where premature shutdown could lead to
latent vport requests without a processor.
This should also address a problem reported by Gal Rosen
(http://marc.info/?l=linux-scsi&m=121731664417358&w=2) where the
driver would attempt to awaken a previously torn-down DPC thread
from interrupt context by implicitly calling wake_up_process()
rather than the driver's qla2xxx_wake_dpc() helper. Rather, than
reshuffle the remove_one() device-removal code, during unload,
depend on the driver's timer to wake-up the DPC process, by
limiting wake-ups based on an 'unloading' flag.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code inadvertently cleared an SRB's 'flags' while
aborting; causing a follow-on scsi_dma_unmap() to be potentially
missed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Minor fixes addressing:
- rport managements during vport deletion.
- acquire proper physical-ha during qla24xx_abort_command() and
qla24xx_queuecommand()
- do not needlessly acquire the pha for non-NPIV capable ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_post_work':
drivers/scsi/qla2xxx/qla_os.c:2158: warning: 'flags' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread. Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All fcport->state management should be done within
qla2x00_mark_device_lost(), the assignment of state within
qla2x00_mark_vp_devices_dead() caused associated rports to not be
removed.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed repeated or unnecessary operations during vport
creation/deletion.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there's no point in adding a fixed-fudge value (originally 5
seconds), honor the user settings only. We also remove the
driver's dead-callback get_rport_dev_loss_tmo function
(qla2x00_get_rport_loss_tmo()).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Initialize all proper structure members in order to support
work-list vport processing. This code also properly acquires the
correct (physical hardware_lock) lock during work submission.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The semaphore vport_sem is used as a mutex. Convert it to the
mutex API.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 63a8651f25 ([SCSI] qla2xxx:
Correct infinite-login-retry issue.) introduced a small
regression where a successful relogin would result in an fcport's
loop_id to be incorrectly reset to FC_NO_LOOP_ID. Only clear-out
loopid, if retries have been 'truly' exhausted.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- qla2x00_alloc_work()
- qla2x00_post_work()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would (incorrectly) only re-register after a
loop-down condition. Also, FDMI registration should be enabled
by default.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there is no actual cable connection on vports, made change so
that the driver checks DFLG_NO_CABLE against ha->device_flags
only for physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that infrastructure is present within the midlayer and there
is a clear distinction between what is expected from a device and
target reset, convert the current device-reset codes to a
target-reset, and add codes to perform a proper device-reset (LUN
reset).
In the process of adding reset support, collapse and consolidate
large sections of mailbox-command (TMF issuance) codes,
generalize the two 'wait-for-commands-to-complete' functions, and
add a generic-reset routine for use by midlayer reset functions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Strip unused (DEBUG-ONLY) enabled functions, inlines, useless
wrappers, and unused DPC flags from the code. Another step in
the migration towards a cleaner (less-crusty) driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Supported events include LIP, LIP reset, RSCN, link up, and link
down.
To support AEN (and additional forthcoming features), we also
introduce a simple deferred-work construct to manage events which
require a non-atomic sleeping-capable context. This work-list is
processed as part of the driver's standard DPC routine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While running IO simultaneously through physical port and virtual
port, if user changes Data Rate (from scli utility), IO through
virtual port fails. It failed because the vport had not received
the ISP_ABORT_NEEDED notification.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no functional change involved with this update, instead
it simply migrates the "set cleared interrupt state" codes to a
more approprate method, qla2x00_request_irqs(), and cleans-up the
driver's probe() logic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Collapse duplicate codes called during probe() and RISC-reset
into qla2x00_setup_chip().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Drop loop-till-allocated structure of code within
qla2x00_mem_alloc().
- Properly unwind deallcations of memory during failures.
- Drop qla2x00_allocate_sp_pool() and qla2x00_free_sp_pool()
functions as their implementations can easily be collapsed into
the callers.
- Defer DMA pool allocation of SFP data until requested.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.
[jejb: resolve conflicts with pci_enable_device_bars removal]
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP. This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer. This can be useful in situations where a physical
connection to the FC bus is not possible.
The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:
<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce
where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for FCE (Fibre Channel Event) tracing support.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of abusing the semaphore interfaces for mailbox command
completions.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As the driver depends on the DPC routine to handle bottom-half
loop resynchronization in order to recover from the issue-lip
request. The issue_lip call is sleeping context capable, so just
issue the reset function there.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver stores the contents of PCI resources into unsigned
long's before ioremapping. This breaks on 32-bit platforms which
support 64-bit MMIO resources.
Correct code by removing the temporary variables used during MMIO
PIO mapping and using resource_size_t where applicable. Also
correct a small typo in a printk() where the wrong region number
was displayed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
WARNING: vmlinux.o(.text+0x2a4462): Section mismatch: reference to .exit.text:qla2x00_remove_one (between 'qla2xxx_pci_error_detected' and 'qla2x00_stop_timer')
qla2x00_remove_one() mustn't be __devexit since it's called from
qla2xxx_pci_error_detected().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent ISPs need only the single MMIO BAR to manipulate HW
registers. Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Drop usage of legacy to_qla_host() macro.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- this patch will fix a panic caused by omitted memory allocation for the nvram.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.
- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iterations is unsigned, so it is impossible to get out of the loop
and return -ETIMEDOUT.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hardcoding the qlport_down_retry module-parameter
effectively disallowed any user-defined NVRAM setting to go
into effect.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove a stale check against ha->device_flags
(DFLG_NO_CABLE) as topology scanning is performed within the
DPC-thread context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Seokmann Ju