The previous algorithm was pretty broken.
- The inner loop had a '(m > m_max)' condition, and the value of 'm'
would increase in each iteration;
- Each iteration would actually multiply 'm' by two, so it is not needed
to re-compute the whole equation at each iteration;
- It would loop until (m & 1) == 0, which means it would loop at most
once.
- The outer loop would divide the 'n' value by two at the end of each
iteration. This meant that for a 12 MHz parent clock and a 1.2 GHz
requested clock, it would first try n=12, then n=6, then n=3, then
n=1, none of which would work; the only valid value is n=2 in this
case.
Simplify this algorithm with a single for loop, which decrements 'n'
after each iteration, addressing all of the above problems.
Fixes: bdbfc02937 ("clk: ingenic: Add support for the JZ4760")
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221214123704.7305-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove redundant -1 entries from the parents array and fix
a couple indentation / whitespace issues.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221026194345.243007-7-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The X1000's CGU supplies the I2S system clock to the AIC module
and ultimately the audio codec, represented by the "i2s" clock.
It is a simple mux which can either pass through EXCLK or a PLL
multiplied by a fractional divider (the "i2s_pll" clock).
The AIC contains a separate 1/N divider controlled by the I2S
driver, which generates the bit clock from the system clock.
The frame clock is always fixed to 1/64th of the bit clock.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221026194345.243007-6-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The set rate hook is called immediately after updating the clock
register but before the spinlock is released. This allows another
register to be updated alongside the main one, which is needed to
handle the I2S divider on some SoCs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221026194345.243007-4-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the enable bit is undefined, the clock is assumed to be always
on and enable/disable is a no-op. When the stable bit is undefined,
the PLL stable check is a no-op.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221026194345.243007-3-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for defining PLL clocks with od_bits = 0, meaning that
OD is fixed to 1 and there is no OD field in the register. In this
case od_max must also be 0, which is enforced with BUG_ON().
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221026194345.243007-2-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Access to registers is guarded by ingenic_tcu_{enable,disable}_regs()
so the stop bit can be cleared before accessing a timer channel, but
those functions did not clear the stop bit on SoCs with a global TCU
clock gate.
Testing on the X1000 has revealed that the stop bits must be cleared
_and_ the global TCU clock must be ungated to access timer registers.
This appears to be the norm on Ingenic SoCs, and is specified in the
documentation for the X1000 and numerous JZ47xx SoCs.
If the stop bit isn't cleared, register writes don't take effect and
the system can be left in a broken state, eg. the watchdog timer may
not run.
The bug probably went unnoticed because stop bits are zeroed when
the SoC is reset, and the kernel does not set them unless a timer
gets disabled at runtime. However, it is possible that a bootloader
or a previous kernel (if using kexec) leaves the stop bits set and
we should not rely on them being cleared.
Fixing this is easy: have ingenic_tcu_{enable,disable}_regs() always
clear the stop bit, regardless of the presence of a global TCU gate.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 4f89e4b8f1 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220617122254.738900-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The TCU clock gate on X1000 wasn't requested by the driver and could
be gated automatically later on in boot, which prevents timers from
running and breaks PWM.
Add a workaround to support old device trees that don't specify the
"tcu" clock gate. In this case the kernel will print a warning and
attempt to continue without the clock, which is wrong, but it could
work if "clk_ignore_unused" is in the kernel arguments.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220412122750.279058-3-aidanmacdonald.0x0@gmail.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Consider CPU, L2 cache, and memory clocks as critical to prevent
them -- and the parent clocks -- from being automatically gated,
since nothing calls clk_get() on these clocks.
Gating the CPU clock hangs the processor, and gating memory makes
external DRAM inaccessible. Normal kernel code can't hope to deal
with either situation so those clocks have to be critical.
The L2 cache is required only if caches are running, and could be
gated if the kernel takes care to flush and disable caches before
gating the clock. There's no mechanism to do this, and probably no
reason to do it, so it's simpler to mark the L2 cache as critical.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220428164454.17908-3-aidanmacdonald.0x0@gmail.com
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> # On X1000 and X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Provide a flags field for clocks under the ingenic-cgu driver,
which can be used to set generic common clock framework flags
on the created clocks. For example, the CLK_IS_CRITICAL flag
is needed for some clocks (such as CPU or memory) to stop them
being automatically disabled.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220428164454.17908-2-aidanmacdonald.0x0@gmail.com
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> # On X1000 and X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The mmc0 clock gate bit was mistakenly assigned to "i2s" clock.
You can find that the same bit is assigned to "mmc0" too.
It leads to mmc0 hang for a long time after any sound activity
also it prevented PM_SLEEP to work properly.
I guess it was introduced by copy-paste from jz4740 driver
where it is really controls I2S clock gate.
Fixes: 226dfa4726 ("clk: Add Ingenic jz4725b CGU driver")
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220205171849.687805-2-lis8215@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Ingenic JZ4760 and JZ4770 both have an extra DMA core named BDMA
dedicated to the NAND and BCH controller, but which can also do
memory-to-memory transfers. The JZ4760 additionally has a DMA core named
MDMA dedicated to memory-to-memory transfers. The programming manual for
the JZ4770 does have a bit for a MDMA clock, but does not seem to have
the hardware wired in.
Add the BDMA and MDMA clocks to the JZ4760 CGU code, and the BDMA clock
to the JZ4770 code, so that the BDMA and MDMA controllers can be used.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211220193319.114974-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- 2 fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
-----BEGIN PGP SIGNATURE-----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=ukBC
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Two fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: watchdog: sunxi: fix error in schema
bindings: media: venus: Drop redundant maxItems for power-domain-names
dt-bindings: Remove Netlogic bindings
clk: versatile: clk-icst: Ensure clock names are unique
of: Support using 'mask' in making device bus id
dt-bindings: treewide: Update @st.com email address to @foss.st.com
dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
dt-bindings: media: Update maintainers for st,stm32-cec.yaml
dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
dt-bindings: timer: Update maintainers for st,stm32-timer
dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files
related to Ingenic SoCs with 'ingenic,'.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
Two fixes in one:
- In the "impose hardware constraints" block, the "logical" divider
value (aka. not translated to the hardware) was clamped to fit in the
register area, but this totally ignored the fact that the divider
value can itself have a fixed divider.
- The code that made sure that the divider value returned by the
function was a multiple of its own fixed divider could result in a
wrong value being calculated, because it was rounded down instead of
rounded up.
Fixes: 4afe2d1a6e ("clk: ingenic: Allow divider value to be divided")
Co-developed-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211001172033.122329-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SoC-specific code can now provide a callback if they need to compute the
M/N/OD values in a specific way.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1000-neo/X1000E
Link: https://lore.kernel.org/r/20210530164923.18134-6-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We can express that a PLL has no bypass bit by simply setting the
.bypass_bit field to a negative value.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-5-paul@crapouillou.net
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1830-neo/X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rework the clock code so that the bypass register is only read when
there is actually a bypass functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-4-paul@crapouillou.net
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1830-neo/X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a clock is declared as both CGU_CLK_DIV and CGU_CLK_MUX, the CGU
code expects the mux to be applied first, the divider second.
On the JZ4760, and maybe on some other SoCs, some clocks also have a mux
setting and a divider, but the divider is not applied to all parents
selectable from the mux.
This could be solved by creating two clocks, one with CGU_CLK_DIV and
one with CGU_CLK_MUX, but that would increase the number of clocks.
Instead, add a 8-bit mask to CGU_CLK_DIV clocks. If the bit
corresponding to the parent clock's index is set, the divider is
bypassed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fc ("clk: ingenic: Add support for divider tables")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clocks that don't have a divider are in our case all marked with the
CLK_SET_RATE_PARENT flag. In this case, the .round_rate implementation
should modify the value pointed to by parent_rate, in order to propagate
the rate change to the parent, as explained in the documentation of
clk_set_rate().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-5-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The custom clocks have custom functions to round, get or set their rate.
Therefore, we can't assume that they need the CLK_SET_RATE_PARENT flag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-4-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CLK_SET_RATE_GATE means that the clock must be gated when being
reclocked. This is not the case for the PLLs in Ingenic SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use the readl_poll_timeout() function instead of rolling our own
busy-wait loops. This makes the code simpler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The to_clk_info() previously had a BUG_ON() to check that it was only
called for PLL clocks. Yet, all the other clocks were doing the exact
same thing the macro does, in-line.
Move the to_clk_info() macro to the top of the file, remove the
hardcoded BUG_ON(), and use it everywhere it makes sense.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add functions for calculat the rate of REFCLK, which is needed by
USB PHY in Ingenic X1000 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Reformat the code (add one level of indentation before the values),
to align the code in the macro definition section.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new functions to "jz4780_otg_phy_ops" to enable or disable the
USB PHY in the JZ4780 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The RTC unit in the Ingenic SoCs has two clock sources, one
is from an external 32.768kHz clock, and the other is from an
external 24MHz/48MHz main clock that is divided by 512. The
choice of these two clocks is controlled by the ERCS bit in
the OPCR register. The RNG unit will also use this clock.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200725051136.58220-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This device id table is passed to of_match_node() later on in probe, but
on CONFIG_OF=n builds of_match_node() doesn't do anything with the
arguments. Lets just mark the table unused so that the compiler doesn't
complain about this.
drivers/clk/ingenic/tcu.c:326:34: warning: unused variable 'ingenic_tcu_of_match' [-Wunused-const-variable]
static const struct of_device_id ingenic_tcu_of_match[] __initconst = {
^
1 warning generated.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200528233837.70269-1-sboyd@kernel.org
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, and ensure that it initialized before
"X1000_CLK_SSIMUX" when initializing the clocks.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU, and gates of CPU, PCLK
are also added.
3.Use "CLK_OF_DECLARE_DRIVER" like the other CGU drivers.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-8-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the clocks provided by the CGU in the Ingenic X1830
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-6-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PLL of X1830 Soc from Ingenic has been greatly changed,
the bypass control is placed in another register, so now two
registers may needed to control the PLL. To this end, a new
"bypass_reg" was introduced. In addition, when calculating
rate, the PLL of X1830 introduced an extra 2x multiplier,
so a new "rate_multiplier" was introduced. And adjust the
code in jz47xx-cgu.c and x1000-cgu.c, make it to be
compatible with the new cgu code.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It is not necessary to use spinlock when reading registers,
so remove it from cgu.c.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When requesting a rate superior to the parent's rate, it would return
-EINVAL instead of simply returning the parent's rate like it should.
Fixes: 4f89e4b8f1 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200213161952.37460-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Exit jz4770_cgu_init() if the 'cgu' pointer we get is NULL, since the
pointer is passed as argument to functions later on.
Fixes: 7a01c19007 ("clk: Add Ingenic jz4770 CGU driver")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lkml.kernel.org/r/20200213161952.37460-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add "jz4780_core1_enable()" for enable the second core of JZ4780,
prepare for later commits.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lkml.kernel.org/r/1582215889-113034-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
X1000 has a different TCU, since X1000 OST has been independent of TCU.
This patch is add TCU support of X1000, and prepare for later OST driver.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lkml.kernel.org/r/1584457893-40418-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Support CGU in Ingenix X1000
- Support Bitmain BM1880 clks
* clk-ingenic:
clk: ingenic: Allow drivers to be built with COMPILE_TEST
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
* clk-init-leak:
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
* clk-ux500:
MAINTAINERS: Update section for Ux500 clock drivers
* clk-bitmain:
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
We don't need the MIPS architecture or even a MIPS compiler to compile
test these drivers. Let's add a COMPILE_TEST possibility on the
menuconfig here so that we can build these drivers on more
configurations.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20191114001925.159276-1-sboyd@kernel.org
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Add support for the clocks provided by the CGU in the Ingenic X1000
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Link: https://lkml.kernel.org/r/1573378102-72380-3-git-send-email-zhouyanjie@zoho.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are a few manually-calculated variable-length struct allocations
left, this converts them to use struct_size. Found with the following
git grep command
git grep -A1 'kzalloc.*sizeof[^_].*+'
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20190927185110.29897-1-steve@sk2.org
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[sboyd@kernel.org: Add grep command]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
By using CLK_OF_DECLARE_DRIVER instead of the CLK_OF_DECLARE macro, we
allow the driver to probe also as a platform driver.
While this driver does not have code to probe as a platform driver, this
is still useful for probing children devices in the case where the
device node is compatible with "simple-mfd".
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20190810123620.27238-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the missing TCU clock to the list of clocks supplied by the CGU for
the JZ4740 SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Add driver to support the clocks provided by the Timer/Counter Unit
(TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
The code was setting the bit 21 of the CPCCR register to use a divider
of 2 for the "pll half" clock, and clearing the bit to use a divider
of 1.
This is the opposite of how this register field works: a cleared bit
means that the /2 divider is used, and a set bit means that the divider
is 1.
Restore the correct behaviour using the newly introduced .div_table
field.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20190701113606.4130-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
Paul Cercueil