By reading the "driver_state" debugfs value we get all the important
state information from the wl12xx driver. This helps testing and
debugging, particularly in situations where the driver seems "stuck".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP, the TX queues are not stopped when we start
recovery. mac80211 is notified only after the fact. When there is
pending TX, it will be queued even after the FW is down. This leads to
situations where the TX queues are stopped (because of the TX-watermark
mechanism), and are never woken up when we return from recovery.
Fix this by explicitly stopping the TX queues when before initiating
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This entry is useful for debugging the driver state machine during
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When there's a change in the basic rates of the AP, reconfigure relevant
templates with the new rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.
When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.
Unify rate configuration on initialization and on change notification
into a single function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When performing recovery, print the firmware version and program
counter (by reading the SCR_PAD4 register). The value of the firmware
program counter during assert can be useful for debugging.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We use a long timeout (2 seconds) when sending commands to the FW.
When a command times out, it means the FW is stuck, and we should
commence recovery.
This should make recovery times shorter as we'll recover on the first
timeout indication.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New AP-mode FWs filter external beacons by default. Disable this
filtering on start up so we can properly configure ERP protection.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the wiphy RTS and fragmentation thresholds for initializing the FW
when possible. This mitigates a bug where previously set values are
forgotten after interface down/up.
Add checks before settings these values to ensure they are valid. Use
default values when invalid thresholds are configured.
Update the default RTS threshold to the maximum value given by the
specification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize AP specific BT coexitance parameters to default values and
enable them in AP mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is preferred to use the setter that to set queue_mapping directly.
This also helps backporting in compat-wireless.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When packets arrive with a RX descriptor indicating corruption, discard
them.
In general white-list the RX descriptor status to prevent rouge data
from being sent up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames are considered pending when they reside in the driver TX queue or
already queued in the FW.
This notion of "pending" is appropriate for power save considerations in
STA mode, but not necessarily in other modes (for instance P2P-GO).
[Fixed a sparse warning about missing "static" in a function
declaration -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW can dynamically manage its internal TX & RX memory pools, moving
blocks from one pool to another when necessary. This can significantly
improve performance. Currently this feature is enabled only for 128x.
Enable dynamic memory for 127x as well. Other parameters in the memory
configuration structure may need to be fine tuned, as the optimal values
for these may change once dynamic memory is enabled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver stops sending TX packets when either there aren't enough
memory blocks, or it runs out of TX descriptors. The driver continues to
send packets to the FW only when more memory blocks are available.
The FW might free TX descriptors without freeing the corresponding
memory blocks, especially when dynamic memory is enabled. In cases where
memory blocks are not freed at all, the driver will keep waiting for
more memory blocks indefinitely.
Fix this by clearing the WL1271_FLAG_FW_TX_BUSY flag when there are
available TX descriptors.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 128x/AP firmware does not yet support dynamic memory. Temporarily,
the memory configuration for the 127x was used both for 127x/AP as well
as 128x/AP. Since the two chips don't have the same number of memory
blocks, TP was significantly degraded.
This hasn't been fine tuned yet, but using the base 128x numbers
(without dynamic memory) seems to yield much better results (around 30%
more). Additional fine tuning will be required in the future.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When configuring ACX_WAKE_UP_CONDITIONS (before entering psm), we
tell the firmware to wake up once in N DTIMs/beacons.
Allow control of this value via debugfs (for debugging purposes).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reducing the retries of sending PS exit packets to the peer AP.
That fix is to avoid sending unrealizable number of PS exit packets
in case of ap lost.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to FM WLAN coexistence (STA only). Some WiFi harmonics
may interfere with FM operation, to avoid this problem special
coexistence techniques are activated around some FM frequencies.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When working in ibss mode, we don't configure rate policy per station
(as we use the same link for multiple stations), so currently the
1mb/s rate is being used.
Instead, configure the firmware to use the whole 11b rates by default.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee80211_reconfig() sets most of the "changed" flags regardless
of the actual change (e.g. BSS_CHANGED_ASSOC will be set even if
the interface is still not associated). in this case the driver
will issue some unneeded commands.
Since the driver relies solely on the BSS_CHANGED_ASSOC flag,
without checking if there was an actual change, it will end up
issuing unjoin() and dummy_join() commands, although it was
never associated and should just remain idle.
Avoid it by checking the actual state change, in addition to the
"changed" flag.
(there seem to be more redundant configuration commands being
issued, but they shouldn't harm)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When debugging, reduce the padding size from each rx packet, to
get the actual packet size (so comparing it against a cap file
will be easier)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix mismatch between the REF CLK and TCXO CLK information that is
set in the platform data and the NVS, so we override what comes
from the NVS and replace it with what comes from the platform data.
[Small fix in a comment -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The elp_work is being enqueued on wl1271_ps_elp_sleep, but doesn't get
cancelled on wl1271_ps_elp_wakeup. This might cause immediate entrance
to elp when the wl->mutex is being released, rather than using the delayed
enqueueing optimization.
Cancel elp_work on wakeup request, and add a new WL1271_FLAG_ELP_REQUESTED
flag to further synchronize the elp actions.
[Fixed a couple of typos in some comments -- Luca]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit d05c806 ("wl12xx: rearrange some ELP wake_up/sleep calls")
introduced a bug in which wl1271_ps_elp_wakeup() was called instead
of wl1271_ps_elp_sleep() after completing the tx work.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
End-of-transaction flag should be set when working with
wl127x chip on AP mode.
Thanks Ido Yariv <ido@wizery.com> for the guidance with that.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.
In STA mode we register only for the MAX_TX_RETRY event. A TX failure is
interpreted as a loss of connection.
Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid
the inherent race condition of a mac80211 TX failure counter in addition
to the FW counter.
This patch depends on "mac80211: allow low level driver to report packet
loss"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.
By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.
Also, remove some unnecessary castings and use union member accesses
instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.
Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.
The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.
In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
multiple places.
3. In the current implementation, the block_size member can be
misleading because a zero value actually means that there's no need to
align. Declare a block size alignment quirk instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.
Update the commentary in order to consider the one valid scenario
where this can happen: roaming.
Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.
Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.
Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).
Fix it by rearranging the elp calls to come along with mutex_lock/unlock.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.
Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using an array of booleans to mark the channels we had already
scanned. This was causing a sparse error, because bool is not a type
with defined size. To fix this, use bitmasks instead, which is much
cleaner anyway.
Thanks Johannes Berg for the idea.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?
Both functions should be static.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310. It now means the passive scan compensation
percentage during A2DP EDR. Instead of 50, we need to use 200.
Fix the SG configuration accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT). Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.
This requires Eliad's fix to set the actual TID in the TX descriptor.
Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.
It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)
Fix it by using the actual tid stored in skb->priority.
Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.
The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.
Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho