Bump HBM version to 2.1 to indicate DMA transfer support.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a circular buffer on allocated system memory. Read and write
indices are stored on the control block which is also shared between the
device and the host.
Two new functions are exported from the DMA module: mei_dma_ring_write,
and mei_dma_ring_empty_slots. The former simply copy a packet on the TX
DMA circular buffer and later, returns the number of empty slots on the
TX DMA circular buffer.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement circular buffer protocol over receive dma
buffer. Add extension to the mei message header that holds
length of the buffer on the dma buffer.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA ring control block contains write and read
indices for host and device circular buffers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA ring is allocated upon HBM handshake and the ring parameters are set
via dedicated HBM_DMA_SETUP request command. The firmware will perform
its setup and respond with a status. On failure the DMA buffers are
released.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate DMA ring buffers from managed coherent memory.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notify set operation ioctl will wait till timeout is expired
even in case when the FW returned an error.
Check the status field of the client object in wait_event_timeout()
to determine if the caller can return earlier.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During queues flush, the me client in most cases is already
unlinked hence the me client id is unavailable. The host client
structure pointer is enough for identification.
The function mei_cl_cmp_id() is dropped as it has no more usage.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop BUG() from the hbm handler in order not to crash the whole
kernel on faulty firmware implementation. Instead of it, just return
an error resulting into link reset.
There is no any known issue of faulty firmware in this matter,
the change is just to ease the development.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like during merging the bulk POLL* -> EPOLL* replacement
missed the patch
'commit af336cabe0 ("mei: limit the number of queued writes")'
Fix sparse warning:
drivers/misc/mei/main.c:602:13: warning: restricted __poll_t degrades to integer
drivers/misc/mei/main.c:605:30: warning: invalid assignment: |=
drivers/misc/mei/main.c:605:30: left side has type restricted __poll_t
drivers/misc/mei/main.c:605:30: right side has type int
Fixes: af336cabe0 ("mei: limit the number of queued writes")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module.h already contains moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a client fails to connect in mei_cldev_enable(), the
caller won't call the mei_cldev_disable leaving the client
in a linked stated. Upon driver unload the client structure
will be freed in mei_cl_bus_dev_release(), leaving a stale pointer
on a fail_list. This will eventually end up in crash
during power down flow in mei_cl_set_disonnected().
RIP: mei_cl_set_disconnected+0x5/0x260[mei]
Call trace:
mei_cl_all_disconnect+0x22/0x30
mei_reset+0x194/0x250
__synchronize_hardirq+0x43/0x50
_cond_resched+0x15/0x30
mei_me_intr_clear+0x20/0x100
mei_stop+0x76/0xb0
mei_me_shutdown+0x3f/0x80
pci_device_shutdown+0x34/0x60
kernel_restart+0x0e/0x30
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200455
Fixes: 'c110cdb17148 ("mei: bus: make a client pointer always available")'
Cc: <stable@vger.kernel.org> 4.10+
Tested-by: Georg Müller <georgmueller@gmx.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the device is not connected it doesn't 'get'
hw module and hence should not 'put' it on disable.
Cc: <stable@vger.kernel.org> 4.16+
Fixes:'commit 257355a44b ("mei: make module referencing local to the bus.c")'
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200455
Tested-by: Georg Müller <georgmueller@gmx.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reports a use-after-free during startup, in mei_cl_write:
BUG: KASAN: use-after-free in mei_cl_write+0x601/0x870 [mei]
(drivers/misc/mei/client.c:1770)
This is caused by commit 98e70866aa ("mei: add support for variable
length mei headers."), which changed the return value from len, to
buf->size. That ends up using a stale buf pointer, because blocking
call, the cb (callback) is deleted in me_cl_complete() function.
However, fortunately, len remains unchanged throughout the function
(and I don't see anything else that would require re-reading buf->size
either), so the fix is to simply revert the change, and return len, as
before.
Fixes: 98e70866aa ("mei: add support for variable length mei headers.")
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the ME clients are available only for BIOS operation and are
removed during hand off to an OS. However the removal is not instant.
A client may be visible on the client list when the mei driver requests
for enumeration, while the subsequent request for properties will be
answered with client not found error value. The default behavior
for an error is to perform client reset while this error is harmless and
the link reset should be prevented. This issue started to be visible due to
suspend/resume timing changes. Currently reported only on the Haswell
based system.
Fixes:
[33.564957] mei_me 0000:00:16.0: hbm: properties response: wrong status = 1 CLIENT_NOT_FOUND
[33.564978] mei_me 0000:00:16.0: mei_irq_read_handler ret = -71.
[33.565270] mei_me 0000:00:16.0: unexpected reset: dev_state = INIT_CLIENTS fw status = 1E000255 60002306 00000200 00004401 00000000 00000010
Cc: <stable@vger.kernel.org>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define dma ring buffer sizes for PCH12 (CLN HW and newer)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only a firmware with version 2.1 and above supports dma ring feature.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dma_ring bit in the mei message header for conveying
that the message data itself are on the dma ring.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The protocol defines how to setup an I/O ring on top of host
memory to utilize the device DMA engine for faster transport.
Three memory buffers are allocated.
A Host circular buffer for from the Host to Device communication.
A Device circular buffer for from Device to the Host communication.
And finally a Control block where the pointers for the both
circular buffers are managed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove header size knowledge from me and txe hw layers,
this requires to change the write handler to accept
header and its length as well as data and its length.
HBM messages are fixed to use basic header, hence we add mei_hbm2slots()
that converts HBM message length and mei message header,
while mei_data2slots() converts data length directly to the slots.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrap the mei header boilerplate initialization code in
mei_msg_hdr_init function. On the way remove 'completed'
field from mei_cl_cb structure as this information
is already included in the header and is local to particular
fragment.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host buffer depth is hardware specific so it's better to
handle it inside the me and txe hw modules. In me the depth
is read from register in txe it's a constant number.
The value is now retrieved via mei_hbuf_depth accessor,
while it replaces mei_hbuf_max_len.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup conversions between slots and data.
Define MEI_SLOT_SIZE instead of using 4 or sizeof(u32) across
the source code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comparison between signed and unsigned warnings
and associated type promotion may cause error
condition not be detected.
The type promotion issue in mei bus was addressed by two patches:
commit b40b3e9358 ("mei: bus: type promotion bug in mei_nfc_if_version()")
commit cf1ed2c59b ("mei: bus: type promotion bug in mei_fwver()")
Now it is possible to suppress the warning, by adding proper
casting to move out of radar.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ssize_t for rets variables in mei_write(), mei_read(), and
mei_cl_write() as well as change the return type of mei_cl_write()
to ssize_t, to prevent assignment of possible 64bit size_t
to int 32 bit variable.
As by product also eliminate warning
drivers/misc/mei/client.c:1702:11: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In for loops use same type for counter variable
as has the limiting variable.
drivers/misc/mei/bus-fixup.c:489:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/misc/mei/hw-txe.c:725:13: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/misc/mei/hw-txe.c:744:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_hbuf_empty_slots() may return with an error in case
of circular buffer overflow. This type of error may
be caused only by a bug. However currently, the error
won't be detected due signed type promotion in comparison to u32.
We add explicit check for less then zero and explicit cast
in comparison to suppress singn-compare warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI enables writes of complete messages only
while read can be performed in parts, hence
write should not update the file offset to
not break interleaving partial reads with writes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if __mei_cl_recv() returns a negative then "bytes_recv"
type is promoted to a high positive value in comparison with
size_t evaluated by MKHI_FWVER_LEN(1). It results in error condition
not to be detected.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9078ad92ef86 ("mei: expose fw version to sysfs")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidentally removed the check for negative returns
without considering the issue of type promotion.
The "if_version_length" variable is type size_t so if __mei_cl_recv()
returns a negative then "bytes_recv" is type promoted
to a high positive value and treated as success.
Cc: <stable@vger.kernel.org>
Fixes: 582ab27a06 ("mei: bus: fix received data size check in NFC fixup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes regression introduced by
commit 8d52af6795 ("mei: speed up the power down flow")
In power down or suspend flow a message can still be received
from the FW because the clients fake disconnection.
In normal case we interpret messages w/o destination as corrupted
and link reset is performed in order to clean the channel,
but during power down link reset is already in progress resulting
in endless loop. To resolve the issue under power down flow we
discard messages silently.
Cc: <stable@vger.kernel.org> 4.16+
Fixes: 8d52af6795 ("mei: speed up the power down flow")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199541
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ME FW version is constantly used by detection and update tools.
To improve the reliability and simplify these tools provide
a sysfs interface to access version of the platform ME firmware
in the following format:
<platform>:<major>.<minor>.<milestone>.<build>.
There can be up to three such blocks for different FW components.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add optional timeout to internal bus recv function to
enable break out of internal flows in case of no answer from FW.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI_IAMTHIF_STALL_TIMER is unused now and can be safely removed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver spams the kernel log on unsupported ioctls which is
unnecessary as the ioctl returns -ENOIOCTLCMD to indicate this anyway.
I suspect this was originally for debugging purposes but it really is not
required so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limit the number of queued writes per client.
Writes above this threshold are blocked till place
in the transmit queue is available.
The limit is configurable via sysfs and defaults to 50.
The implementation should provide blocking I/O behavior.
Prior to this change one would end up in the hands of OOM.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Module reference counting is relevant only to the
mei client devices. Make the implementation clean
and move it to bus.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CNP LP and CNP H device ids for cannon lake
and coffee lake platforms.
Cc: <stable@vger.kernel.org> 4.14+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes regression introduced by
commit 8d52af6795 ("mei: speed up the power down flow")
In mei_cldev_disable during device power down flow, such as
suspend or system power off, it jumps over disconnecting function
to speed up the power down process, however, because the client is
unlinked from the file_list (mei_cl_unlink) mei_cl_set_disconnected
is not called from mei_cl_all_disconnect leaving resource leaking.
The most visible is reference counter on underlying HW module is
not decreased preventing to remove modules after suspend/resume cycles.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Fixes: 8d52af6795 ("mei: speed up the power down flow")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
->dev_state can't be both MEI_DEV_RESETTING and MEI_DEV_POWER_DOWN at
the same time. && was clearing intended here.
Fixes: 8d52af6795 ("mei: speed up the power down flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current expression using the || operator is always true because
dev->dev_state cannot be equal to two different values at the same time.
Fix this by replacing the || with &&.
Detected by CoverityScan, CID#1463042 ("Constant expression result")
Fixes: 8d52af6795 ("mei: speed up the power down flow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From the pci power documentation:
"The driver itself should not call pm_runtime_allow(), though. Instead,
it should let user space or some platform-specific code do that (user space
can do it via sysfs as stated above)..."
However, the S0ix residency cannot be reached without MEI device getting
into low power state. Hence, for mei devices that support D0i3, it's better
to make runtime power management mandatory and not rely on the system
integration such as udev rules.
This policy cannot be applied globally as some older platforms
were found to have broken power management.
Cc: <stable@vger.kernel.org> v4.13+
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in dev_dbg debug message. Also
add in a missing comma.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mei driver is powering down due to suspend or shutdown
it will iterate over the mei client bus and disconnect
each client device attached in turn.
The power down flow consist of the link rest, which causes all clients
get disconnected at once, hence the individual disconnection
can be omitted and significantly reduce power down flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
Replace the PCI-specific flag PCI_DEV_FLAGS_NEEDS_RESUME with the
PM core's DPM_FLAG_NEVER_SKIP one everywhere and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a96c548291 ("mei: trace pci configuration space io") added the
trace event mei_pci_cfg_write but never used it. As trace events that
are defined take up space for data structures and functions created for
them, it is a waste of memory to have one defined but not used. Remove
this trace event.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a regression caused by the new changes
in the "run wake" handlers.
The mei devices that support D0i3 are no longer receiving an interrupt
after entering runtime suspend state and will stall.
pci_dev_run_wake function now returns "true" for some devices
(including mei) for which it used to return "false",
arguably incorrectly as "run wake" used to mean that
wakeup signals can be generated for a device in
the working state of the system, so it could not be enabled
or disabled before too.
MEI maps runtime suspend/resume to its own defined
power gating (PG) states, (D0i3 or other depending on generation),
hence we need to go around the native PCI runtime service which
eventually brings the device into D3cold/hot state,
but the mei devices cannot wake up from D3 unlike from D0i3/PG state,
which keeps irq running.
To get around PCI device native runtime pm,
MEI uses runtime pm domain handlers which take precedence.
Cc: <stable@vger.kernel.org> #4.13+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device 'new_id' interface is useful for testing of not yet published
hardware on older kernels and for internally used device ids on
simulation platforms.
However currently with the device configuration held in device_id driver
data as a pointer to mei_cfg structure it is hard, as one need to locate
the address of the correct structure.
A recommended way of doing that is to use and index instead of a
pointer.
This patch adds a new list of configuration mei_cfg_list[]
indexed via enum mei_cfg_idx.
In addition it cleanups ich platform naming, renames legacy
generation to ich and what was ich to ich10.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, currently Broxton, Apollo Lake and Kaby Lake,
ME FW may be busy with internal bookkeeping and answering late
to the start message.
As a mitigation, the driver requests for a synchronous probing
to prevent stalling of the overall boot process. For example,
on a Apollo Lake platform the overall boot time has reduced from
~0.9 to ~0.6 seconds on average.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device disabled state is caught inside the retry loop, so
there is no need to check it once again afterwards.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX message header is received in the first fragment of
the message and saved side and it is not modified after that,
we don't need to validate it upon each fragment.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
modprobe is not able to resolve sysfs modalias for mei devices.
# cat
/sys/class/watchdog/watchdog0/device/watchdog/watchdog0/device/modalias
mei::05b79a6f-4628-4d7f-899d-a91514cb32ab:
# modprobe --set-version 4.9.6-200.fc25.x86_64 -R
mei::05b79a6f-4628-4d7f-899d-a91514cb32ab:
modprobe: FATAL: Module mei::05b79a6f-4628-4d7f-899d-a91514cb32ab: not
found in directory /lib/modules/4.9.6-200.fc25.x86_64
# cat /lib/modules/4.9.6-200.fc25.x86_64/modules.alias | grep
05b79a6f-4628-4d7f-899d-a91514cb32ab
alias mei:*:05b79a6f-4628-4d7f-899d-a91514cb32ab:*:* mei_wdt
commit b26864cad1 ("mei: bus: add client protocol
version to the device alias"), however sysfs modalias
is still in formmat mei:S:uuid:*.
This patch equates format of uevent and sysfs modalias so that modprobe
is able to resolve the aliases.
Cc: <stable@vger.kernel.org> 4.7+
Fixes: commit b26864cad1 ("mei: bus: add client protocol version to the device alias")
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_cl_bus_rescan is used only in bus.c,
so make it local to the file and mark static.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write() returns successfully, it is only assumed that a message
was successfully queued. Add fsync syscall implementation to help
user-space ensure that all data is written.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Though VLA are supported by CC99 there are many cavities
and should be avoided.
'const size_t len = sizeof()' that we used may not be set
at the compile time hence generating VLA code.
This fixes also sparse warning
warning: Variable length array is used type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Though VLA are supported by CC99 there are many cavities
and should be avoided.
'const size_t len = sizeof()' that we used may not be set
at the compile time hence generating VLA code.
This fixes also sparse warning
warning: Variable length array is used type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMTHIF has special support in the mei drive, it handles multiplexing
multiple user space connection above single me client connection.
Since there is no additional addressing information there is a strict
requirement on the traffic order on each connection and on the "read
after write" order within the connection. This creates a lot of
complexity mostly because the other client types do not necessarily fall
under the same restriction. After carefully studying the use of the
AMTHIF client, we came to conclusion that the multiplexing is not really
utilized by any application and we may safely remove that support and
significantly simplify the driver.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The shutdown handler quiesces the device, it performs link reset in
order to close all connections and notify the device that is not longer
managed by the driver.
This is essentially a stripped down version of the PCI remove() function
where only the necessary amount of work is done to stop any further
activity.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver still struggles with firmwares that do not replay to the OS
version request. It is safe not waiting for the replay. First, the driver
doesn't do anything with the replay second the connection is closed
immediately, hence the packet will be just safely discarded in case it
is received and last the driver won't get stuck if the firmware won't
reply.
Cc: <stable@vger.kernel.org> #4.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes 'mei: synchronize irq before initiating a reset'
The patch had introduced a deadlock between irq thread and mei_reset()
as they are both holding the same device lock.
---> device_lock:
mei_reset()
<---- interrupt thread
device_lock
---> synchornize_irq()
wait on interrupt thread == (dead lock)
The fix is to call synchronize_irq
prior to call locked mei_reset function.
Cc: <stable@vger.kernel.org> #4.10+
Fixes: f302bb0de6ac (mei: synchronize irq before initiating a reset)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here. Rework for the hyperv
subsystem to handle new platforms better, mei and w1 and extcon driver
updates, as well as a number of other "minor" driver updates. Full
details are in the shortlog below.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2iRQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynhFACguVE+/ixj5u5bT5DXQaZNai/6zIAAmgMWwd/t
YTD2cwsJsGbTT1fY3SUe
=CiSI
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here: rework for the
hyperv subsystem to handle new platforms better, mei and w1 and extcon
driver updates, as well as a number of other "minor" driver updates.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
goldfish: Sanitize the broken interrupt handler
x86/platform/goldfish: Prevent unconditional loading
vmbus: replace modulus operation with subtraction
vmbus: constify parameters where possible
vmbus: expose hv_begin/end_read
vmbus: remove conditional locking of vmbus_write
vmbus: add direct isr callback mode
vmbus: change to per channel tasklet
vmbus: put related per-cpu variable together
vmbus: callback is in softirq not workqueue
binder: Add support for file-descriptor arrays
binder: Add support for scatter-gather
binder: Add extra size to allocator
binder: Refactor binder_transact()
binder: Support multiple /dev instances
binder: Deal with contexts in debugfs
binder: Support multiple context managers
binder: Split flat_binder_object
auxdisplay: ht16k33: remove private workqueue
auxdisplay: ht16k33: rework input device initialization
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
Parallel reads from multiple threads on a file descriptor
are not well defined and racy. It is safer to return to original
behavior and simply fail the additional read.
The solution is to remove request for next read credit.
Cc: <stable@vger.kernel.org> #4.9
Fixes: ff1586a7ea ("mei: enqueue consecutive reads")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rare case the driver may lose connection with the device after device
reset due to a missed interrupt. The driver will unlock the flow by
generating an interrupt towards the firmware (HIG) when the device is in
the resetting state. The FW is able to ignore the interrupt during
orderly flow. The effected platforms are skylake and newer.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consolidate setting H_IG, an interrupt from host towards hw,
into a wrapper to eliminate code duplication.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ and pcim_ functions to make error handling
simpler and code smaller and tidier.
Based on original patch by
mei: me: use managed functions pcim_* and devm_*
https://lkml.org/lkml/2016/2/1/339
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specify in function names by which object is the io list filtered:
cl for a client and fp for file descriptor.
In that course a code duplication is resolved by dropping
mei_cl_read_cb_flush and mei_clear_list and using
mei_io_list_free_fp function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_dev structure used struct mei_cl_cb type variables as for holding
callbacks list heads. Replace them by the actual struct list_head
as there is no other info that is handled. This slims down
the mei_dev structure and mostly streamline the code.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amthif client connection is shared over multiple file descriptors.
In case a file descriptor was closed immediately after a write, the read
credits should be still available so the pending reads can be cleaned
from the queue, hence we cannot drop the control read list, this is
done only upon connection close.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prevent memory leak clean up the amthif command
queue upon disconnection. The issue may happen only on error path
as the command queue is cleaned upon file descriptor close.
And remove the cleanup from mei_cl_flush_queues as this code
is never reached for amthif client.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On legacy HW, pre Skylake, the notifications are not supported,
return -EOPNOTSUPP in mei_cl_notify_get and prevent
waiting indefinitely.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request for a notification from a disconnected client will be ignored
silently by the FW but the caller should know that the operation hasn't
succeeded.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop and unregister receive and notification callbacks
from the disable function, to allow its later re-enablement.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware module should not be unloaded if the bus
has active devices.
Get get_/put_ bus parent module upon client device
connection/disconnection, to prevent the hardware managing
module to disappear underneath.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A driver on the mei bus may rely on the availability
of the receive callback during driver remove() call, e.g. mei_wdt.
Move callbacks dismantling after the remove() call to unblock that scenario.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_cl_set_disconnected is used only in client.c,
so make it local to the file and mark static.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_io_list_flush is used only in client.c
so make it local to the file and mark static.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sending OS version for support of TPM2_ChangeEPS() is required only
for SPT FW (HMB version 2.0) and newer.
On older platforms the command should be just ignored by the firmware
but some older platforms misbehave so it's safer to send the command
only if required.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192051
Fixes: 7279b238ba (mei: send OS type to the FW)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The credentials handling was pushed to the write handlers
but error handling wasn't done properly.
Move write callbacks to completion queue to destroy them
and to notify a blocked writer about the failure
Fixes: 136698e535 (mei: push credentials inside the irq write handler)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust function name in KDoc.
Fixes: d49dc5e76f (mei: bus: use mei_cldev_ prefix for the API functions)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable non-blocking receive for drivers on mei bus, this allows checking
for data availability by mei client drivers. This is most effective for
fixed address clients, that lacks flow control.
This function adds new API function mei_cldev_recv_nonblock(), it
retuns -EGAIN if function will block.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the newer HW sports two interrupts causes we cannot
just simply acknowledge the interrupts directly in the quick handler
and store the cause in the member variable, as the cause
will be overridden upon next interrupt while the interrupt thread
was not yet scheduled handling the previous interrupt.
The simple fix is to disable interrupts in quick handler
and acknowledge and enabled them in the interrupt thread.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to synchronize irqs before issuing reset to make sure that the
clients communication is concluded and doesn't leak to the reset flow
and confusing the state machine.
This issue is happening during suspend/resume stress testing.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Usyskin