According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230315055023.61779-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kunit_test_suite() macro is no-longer incompatible with module_add,
so its use can be reinstated.
Since this fixes parsing with builtins and kunit_tool, also enable the
test by default when KUNIT_ALL_TESTS is enabled.
The test can now be run via kunit_tool with:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_OF=y --kconfig_add CONFIG_OF_ADDRESS=y \
--kconfig_add CONFIG_MMC=y --kconfig_add CONFIG_MMC_SDHCI=y \
--kconfig_add CONFIG_MMC_SDHCI_PLTFM=y \
--kconfig_add CONFIG_MMC_SDHCI_OF_ASPEED=y \
'sdhci-of-aspeed'
(It may be worth adding a .kunitconfig at some point, as there are
enough dependencies to make that command scarily long.)
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The card timing and the bus frequency are not changed atomically with
respect to calls to the set_clock() callback in the driver. The result
is the driver sees a transient state where there's a mismatch between
the two and thus the inputs to the phase correction calculation
formula are garbage.
Switch from dev_warn() to dev_dbg() to avoid noise in the normal case,
though the change does make bad configurations less likely to be
noticed.
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607013020.85885-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware provides capability configuration registers for each SDHCI
in the global configuration space for the SD controller. Writes to the
global capability registers are mirrored to the capability registers in
the associated SDHCI. Configuration of the capabilities must be written
through the mirror registers prior to initialisation of the SDHCI.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210524073308.9328-5-steven_lee@aspeedtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being
used in the entire c-file". Convert all the mmc->parent usage in all
sdhci host driver to mmc_dev() for consistency.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Randy found that with the following Kconfig settings we have duplicate
definitions (e.g. __inittest()) in sdhci-of-aspeed due to competing
module_init()/module_exit() calls from kunit and driver the itself.
```
CONFIG_MMC_SDHCI_OF_ASPEED=m
CONFIG_MMC_SDHCI_OF_ASPEED_TEST=y
```
Conditionally open-code the kunit initialisation to avoid the error.
Fixes: 7efa02a981d6 ("mmc: sdhci-of-aspeed: Add KUnit tests for phase calculations")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210122114852.3790565-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Converting degrees of phase to logic delays is irritating to test on
hardware, so lets exercise the function using KUnit.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-5-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The AST2600 can achieve HS200 speeds with a change to the bus clock
divisor behaviour. The divisor can also be more accurate with respect
to the requested clock rate, but keep the one-hot behaviour for
backwards compatibility with the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-4-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Aspeed SD/eMMC controllers expose configurable clock phase
correction by inserting delays of up to 15 logic elements in length into
the bus clock path. The hardware supports independent configuration for
both bus directions on a per-slot basis.
The timing delay per element encoded in the driver was experimentally
determined by scope measurements.
The phase controls for both slots are grouped together in a single
register of the global register block of the SD/MMC controller(s), which
drives the use of a locking scheme between the SDHCIs and the global
register set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-3-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v5.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.5.I2b630c4d40ff4ea61d5b30b8ccfe95890e257100@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calculating the clock divider, start dividing at 2 instead of 1.
The divider is divided by two at the end of the calculation, so starting
at 1 may result in a divider of 0, which shouldn't happen.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200709195706.12741-3-eajames@linux.ibm.com
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add read_l callback in sdhci_ops with flipping of SDHCI_CARD_PRESENT
bit in case of inverted card detection signal.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a get_max_clock() handler to sdhci-of-aspeed to report f_max as the
maximum clock rate if it is set. This enables artificial limitation of
the bus speed via max-frequency in the devicetree for e.g. the AST2600
evaluation board where I was seeing errors at 200MHz.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The early-exit didn't seem to matter on the AST2500, but on the AST2600
the SD clock genuinely may not be running on entry to
aspeed_sdhci_set_clock(). Remove the early exit to ensure we always run
sdhci_enable_clk().
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.
The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).
The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.
Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.
Signed-off-by: Ryan Chen <ryanchen.aspeed@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yang Li