Trivial fix to spelling mistake "configutation" to "configuration"
in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
cec_read() is non-atomic in the presence of other I2C bus transactions
to the same device. This presents a problem when we add support for
the TDA9950 CEC engine part - both drivers can be trying to access the
device.
Avoid the inherent problems by switching to i2c_transfer() instead,
which allows us to perform more than one bus transaction atomically.
As this means we will be using I2C transactions rather than SMBUS, we
have to check that the host supports I2C functionality.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some TDA998x contain several different I2C devices - there is the HDMI
encoder, and there is a TDA9950 CEC engine. These two share the same
interrupt signal.
In order to allow a driver for the CEC engine to work, we need to be
able to share the interrupt with the CEC driver, so convert the handler
and registration to allow this to happen.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Disabling the pre-filter block of the TDA998x saves 40mW and the colour
conversion block saves 15mW. As we always disable these two blocks, we
can power these sections of the chip down to save 55mW of unnecessary
power consumption.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Rather than storing the DPMS mode (which will always be on or off) use a
boolean to store this instead.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
tda998x_audio_get_eld() is needlessly complex - the connector associated
with the encoder is always our own priv->connector. Remove this
complexity, but ensure that there are no races when copying out the ELD.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x audio functions together rather than split between
two different locations in the file, keeping like code together.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Separate out the connector initialisation from the rest of the drivers
initialisation.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x connector functions and funcs structures together
before the encoder support, rather than scattered amongst the rest of
the file. This keeps like code together.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The naming of tda998x_encoder_set_config() is a left-over from when
TDA998x was a slave encoder. Since this is part of the initialisation,
drop the _encoder from the name, and move it near tda998x_bind().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Correct two references to tda998x_connector_get_modes() which were
incorrectly referring to tda998x_encoder_get_modes().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Check for audio support by the attached sink by consulting the EDID
prior to enabling audio over the TMDS link. We must consult the EDID
after calling drm_helper_probe_single_connector_modes(), as this can
use an override EDID, or load a replacement EDID.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The CEA 861B specification indicates the situations when we are able to
send each infoframe based on the version of the EDID's CEA extension.
Update the tda998x driver to follow the CEA specification wrt sending
of infoframes.
Since we only support the generation of AVI version 2, this limits us
to CEA extension version 3, so we treat CEA extension version 2 as
CEA 861 (no infoframes, no audio.)
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a race between programming audio and an in-progress mode set.
A mode set is complex, and disables the ability to send infoframes
to the sink, and is disruptive to audio - we have to mute the audio
FIFO while doing a mode set.
If an attempt is made to start up the audio side, we will undo the
audio FIFO mute before the mode set has completed.
Move the lock so that we prevent audio interfering with an in-progress
mode set.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a racy access to the mode clock by storing the current mode clock
during a mode set under the audio mutex. This allows us to access it
from the audio path in a safe way.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As priv->audio_params can now be changed at run time, we need to be more
careful about how we deal with a mode set. We must take the audio lock
while checking if there's a valid audio configuration.
However, it's slightly worse than that - during mode set, we mute the
audio, and it must not be unmuted until we have finished the mode set.
It is possible that the audio side may start while a mode set is in
progress, so take the audio_mutex lock around the whole mode setting
procedure.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We will need the audio mutex initialised in all cases, so lets move this
to be early, rather than only being initialised for the DT case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Connectors shouldn't be registered until the rest of the whole device
is set up, so that consistent state is presented to userspace.
As such, remove the calls to drm_connector_register() and
drm_connector_unregister() from tda998x, as these are now handled by
drm_dev_(un)register() itself.
To work with this change, the mali-dp and hdlcd bind and unbind
sequences have to be reordered, to ensure that the componentised
encoder/connector is bound before drm_dev_register() registers all
connectors. Similarly, the device must be unregistered before the
component is unbound.
Altogether, this allows other drivers using tda998x to be
de-midlayered, and to have less racy initialisation of their components.
Splitting this commit into three (one per driver) isn't possible without
intermediate breakage, so it is all squashed together here.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Register ASoC HDMI codec for audio functionality and adds device tree
binding for audio configuration.
With the registered HDMI codec the tda998x node can be used like a
regular codec node in ASoC card configurations. HDMI audio info-frame
and audio stream header is generated by the ASoC HDMI codec. The codec
also applies constraints for available sample-rates based on Edid Like
Data from the display. The device tree binding document has been
updated [1].
Part of this patch has been inspired by Jean Francoise's "drm/i2c: tda998x:
Add support of a DT graph of ports"-patch [2]. There may still be some
identical lines left from the original patch and some of the ideas
have come from there.
[1] Documentation/devicetree/bindings/display/bridge/tda998x.txt
[2] http://mailman.alsa-project.org/pipermail/alsa-devel/2015-July/095255.html
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Define struct tda998x_audio_params in include/drm/i2c/tda998x.h and
use it in pdata and for tda998x_configure_audio() parameters. Also
updates tda998x_write_aif() to take struct hdmi_audio_infoframe *
directly as a parameter.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The driver has been converted to use drm_bridge instead of
drm_i2c_slave_encoder. We can now move it to the bridge folder.
Create a separate folder since we already have a couple of files and
expect more when we support audio and ADV7533.
Rename the driver to adv7511_drv.c. This will come in handy later
when the driver module will need to be built from multiple object
files.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
We don't want to use the old i2c slave encoder interface anymore.
Remove that and make the i2c driver create a drm_bridge entity instead.
Converting to bridges helps because the kms drivers don't need to
exract encoder slave ops from this driver and use it within their
own encoder/connector ops.
The driver now creates its own connector when a kms driver attaches
itself to the bridge. Therefore, kms drivers don't need to create
their own connectors anymore.
The old encoder slave ops are now used by the new bridge and connector
entities.
The of_node member in drm_bridge is accessible only when CONFIG_OF is
enabled. The driver anyway only works only when OF is available. Make
the driver depend on OF in its Kconfig.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Choose between atomic or non atomic connector dpms helper. If tda998x
is connected to a drm driver that does not support atomic modeset
calling drm_atomic_helper_connector_dpms() causes a crash when the
connectors atomic state is not initialized. The patch implements a
driver specific connector dpms helper that calls
drm_atomic_helper_connector_dpms() if driver supports DRIVER_ATOMIC
and otherwise it calls the legacy drm_helper_connector_dpms().
Fixes commit 9736e988d3 ("drm/i2c: tda998x: Add support for atomic
modesetting").
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix this typo, consequently used over both files :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
This register includes a counter which is decremented by the chip on I2C
failures. Also, it is reset when powering down.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
The interrupts for EDID_READY or DDC_ERROR were never enabled in this
driver, so reading EDID always timed out when chip was powered down and
interrupts were used. Fix this and also remove clearing the interrupt
flags, they are cleared in POWER_DOWN mode anyhow (unlike the interrupt
enable flags) according to docs and my tests.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
An encoder is associated with a connector by the DRM core as a result of
setting up a configuration. Drivers using the atomic or legacy helpers
should never set up this link, even if it is a static one.
While at it, try to catch this kind of error in the future by adding a
WARN_ON() in drm_mode_connector_attach_encoder(). Note that this doesn't
cover all the cases, since drivers could set this up after attaching.
Drivers that use the atomic helpers will get a warning later on, though,
so hopefully the two combined cover enough to help people avoid this in
the future.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447694393-24700-1-git-send-email-thierry.reding@gmail.com
These changes from Liviu add support for atomic mode setting, add the
TMDS clock limitation according to the device, and ensure that we
correctly clean up in the unbind function.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: Add support for atomic modesetting
drm/i2c: tda998x: increase the supported dotclock frequency to 165MHz for TDA19988
drm/i2c: tda998x: unregister the connector in the unbind function
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/i2c/adv7511.ko:
-.rodata 1368
+.rodata 1416
-.data 164
+.data 116
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-20-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
save/restore have been removed from drm_encoder_helper_funcs by
'commit 79f13ad5d8e0 ("drm: Move encoder->save/restore into nouveau")'
But this module was still defining it with empty content causing
compilation fails:
drivers/gpu/drm/i2c/tda998x_drv.c:1354:10: warning: initialization from
incompatible pointer type [-Wincompatible-pointer-types]
.save = tda998x_encoder_save,
drivers/gpu/drm/i2c/tda998x_drv.c:1355:2: error: unknown field 'restore'
specified in initializer
.restore = tda998x_encoder_restore,
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449513306-17309-1-git-send-email-rodrigo.vivi@intel.com
When used with a DRIVER_ATOMIC enabled CRTC driver, the tda998x
will cause crashes due to missing atomic operations. Fill the
drm_connector_funcs struct with the atomic versions of the required
functions and add the atomic modeset specific callbacks.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Spec sheet states that the TDA19988 supports up to 165MHz dotclock
speeds. Without this change modes higher than 1080p are un-attainable.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tda998x uses drm_connector_register() in the .bind function that
needs to be balanced with a drm_connector_unregister() in the .unbind.
Otherwise dangling sysfs entries are left behind and future rebinds
will fail.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* removes the now unused DRM slave encoder support, which all users have
migrated away from, allowing us to simplify the code.
* ensure all pending interrupts are processed together, rather than
needing the handler to be re-entered each time.
* use more HDMI helpers to setup the info frames.
* fix EDID read handling by ensuring that we always wait the specified time
before attempting to read the EDID, no matter where the EDID read request
came from.
* 'drm-tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: clean up after struct tda998x_priv2 removal
drm/i2c: tda998x: kill struct tda998x_priv2
drm/i2c: tda998x: move connector into struct tda998x_priv
drm/i2c: tda998x: remove encoder pointer
drm/i2c: tda998x: remove DRM slave encoder support
drm/i2c: tda998x: use more HDMI helpers
drm/i2c: tda998x: handle all outstanding interrupts
drm/i2c: tda998x: convert to u8/u16/u32 types
drm/i2c: tda998x: re-implement "Fix EDID read timeout on HDMI connect"
drm/i2c: tda998x: report whether we actually handled the IRQ
drm/i2c: tda998x: remove useless NULL checks
We can now kill a number of glue functions which were sitting between
the common tda998x code and the drm encoder/connector methods. This
results in slightly cleaner code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kill the redundant tda998x_priv2 structure now that its only member is
the struct tda998x_priv.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the encoder pointer from struct tda998x_priv, moving the encoder
itself from struct tda998x_priv2 here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the DRM slave encoder compatibility from the TDA998x driver. We
now use the component helpers to manage the binding of DRM sub-drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Masahiro Yamada