Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A). This patch removes the indep_hp flag for such codecs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA. Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The failures of buffer preallocations at driver initializations aren't
critical but it's still helpful to inform, so that user can know that
something doesn't work as expected.
For example, the recent page allocator change triggered regressions,
but developers didn't notice until recently because the driver didn't
complain.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add controls to enable/disable the headphone short circuit protection of
the headphone outputs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Occasionally, on playback stream ringbuffer wraparound, the EMU20K1
hardware will momentarily return 0 instead of the proper current(loop)
address. This patch handles that case, fixing the problem of playback
position corruption and subsequent loss of buffered sound data, that
occurs with some common buffering layout patterns(e.g. multiple
simultaneous output streams with differently-sized or
non-power-of-2-sized buffers).
An alternate means of fixing the problem would be to read the ca
register continuously, until two sequential reads return the same
value; however, that would be a more invasive change, has performance
implications, and isn't necessary unless there are also issues with the
value not being updated atomically in regards to individual bits or
something similar(which I have not encountered through light testing).
I have no EMU20K2 hardware to confirm if the issue is present there,
but even if it's not, this change shouldn't break anything that's not
already broken.
Signed-off-by: Sarah Bessmer <aotos@fastmail.fm>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the dt is used and the cinfo is NULL, the -ENOMEM should be return.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If the dt is not used, the cinfo will be always NULL before using it.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For those platforms using DAI master mode like I2S, it's better to pre-set
a default slot number so that there's no need for these common cases to set
the slot number from its machine driver any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the missing clk_disable_unprepare() before return from
fsl_ssi_probe() in the request irq error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some DMA cores might add additional restrictions on which in memory audio
formats can be supported by the compound sound card. If the PCM component
specifies a set of formats it supports (by setting the formats field to non 0)
take these into account when calculating the format set for the compound sound
card.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
single_open requires a function with signature
'int (*)(struct seq_file *, void *)'. This patch fixes the warning by
fixing the wrong return type of fsl_ssi_stats_show.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of keeping a separate snd-page-alloc module, merge into the
core snd-pcm module, as we don't need to keep it as an individual
module due to the drop of page reservation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nowadays we have CMA for obtaining the contiguous memory pages
efficiently. Let's kill the old kludge for reserving the memory pages
for large buffers. It was rarely useful (only for preserving pages
among module reloading or a little help by an early boot scripting),
used only by a couple of drivers, and yet it gives too much ugliness
than its benefit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the device ID for Intel Broadwell display HD-Audio controller,
and applies Haswell properties to this device.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_SND_SOC_DMAENGINE_PCM was renamed to CONFIG_SND_DMAENGINE_PCM
recently. And yet we don't have to select it since
CONFIG_SND_GENERIC_DMAENGINE_PCM selects the dependency by itself, so
just rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the start of booting the DSP to earlier in the DAPM process, and
move the final starting of the DSP to later in the DAPM process. This
allows us to overlap some of the processing with other components of the
system being brought up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the ADSP2 boot proceedure into a work structure in preparation for
running it asynchronously with the reset of the audio path bring up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The normal trigger function can now be used for AC97. Drop AC97 trigger
function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch defines the appropriate register values for different
oparation modes and IP versions. We have to handle DMA/FIQ, AC97,
DEBUG-IRQs and offline/online configuration support.
With this patch we cleanup some driver code that was not reference
manual conform and try to cleanup the whole trigger function to seperate
the actual register values from the enable/disable logic, which is now
hidden in fsl_ssi_config helpers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a struct 'fsl_ssi_rxtx_reg_val' which holds register
values necessary to enable rx/tx. Based on those preset register values,
the added configuration functions will cleanly enable/disable different
parts of the SSI IP while supporting online/offline configuration.
Different operating modes can be setup directly as different register
values in fsl_ssi_reg_val.
These functions and structs will help to cleanup and simplify the
trigger function to support many different IP versions (online/offline
configuration) and different operating modes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx50-ssi and later versions of this IP support online reconfiguration
of all registers. The reference manual does not list any registers that
can only be configured while the SSI unit is disabled. This patch
introduces the flag for later use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
irqs should only be requested/released with enabled DMA. Previously
interrupt statistics where disabled for IMX Processors because of
different writeable SISR bits.
This patch introduces support for irqstats on imx processors again by
creating a sisr writeback mask and introducing a imx35-ssi compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a small but significant difference between imx21-ssi and
imx51-ssi and above. imx21-ssi does not allow online reconfiguration of
some registers. They have to be configured at the beginning.
imx51-ssi has to reconfigure the SSI unit while it is running. Otherwise
it would not be possible to have two streams in parallel. The new SDMA
unit in imx51 and above has to be configured before the first DMA
request arrives. Therefor we need to setup TDMAE/RDMAE just before
starting the stream.
This patch introduces distinct imx51-ssi as compatible and adds
of_device_id matching in the probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Interrupt statistics of fsl_ssi are mainly for debugging purpose. Most
of those interrupts show error states, e.g. under/overflow.
The stats should be exposed via debugfs instead of sysfs.
This patch moves the statistics file to debugfs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the error handling in the fsl-ssi probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both patch_realtek.c and patch_conexant.c contain the fairy same code
snippet for supporting Thinkpad ACPI LED controls. Split them into
thinkpad_helper.c and include it from both places. Although this
isn't the best approach from the code size POV, the probability for
coexistence of both Realtek and Conexant codecs on a single machine is
pretty low, thus it'll end up with less memory footprint than
splitting to yet another module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSM260x also supports 16kHz with external master clocks of 12.000MHz,
12.288MHz and 18.432MHz.
Add matching coefficients, update constraints and announced rates.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
To avoid another lookup for the twl4030_priv in there.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's no other users of this functionality, the code can be moved inside
of twl4030_write.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Over time the multi line alignment got messed up. Correct them in one go
so the code will look consistent.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Depend on the regmap reg cache implementation for register caching done in
the twl-core driver.
The local register cache can be removed and we can keep only shadow copies
of certain ctl registers for pop noise reduction.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Few registers need to be cached in the codec driver level. These registers
should only be written when the path is active to avoid pop noise on the
given path.
This patch adds an array which covers the range where the sensitive registers
are located and uppon loadinf the driver the ctl cache will be initialized.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The register states now tracked by the regmap implementation in the core which
makes the reset registers functionality 'redundant' since we know the state
of the registers now all the time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to keep the check defaults functionality anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplifies the code a bit and prepares it to the removal of local caching.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following sparse warning:
sound/soc/ux500/ux500_msp_i2s.c:649:5: warning:
symbol 'ux500_msp_i2s_of_init_msp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.
Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide a quick way to tell if a DAI is a dummy DAI or a regular DAI.
This is for internal DAPM usage only and is used to determine whether to
insert a DAI link connection into the DAPM graph.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints. This makes even me referring back to the
document often. Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead. No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that some AMD HDMI controllers still don't provide
proper values in GCAP register (all zero), and the driver assigns only
one stream in that case, although the connected codec chip supports
more than one stream.
In this patch, the default max number of streams for AMD HDMI
controllers is increased to 8, which should suffice for most use
cases. The overhead by this increase is more azx_dev struct and BDL
allocations, so it's negligible. Of course, if the controller
provides a proper GCAP register, the register value would be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BE DAIs can be "dummy" (when the DSP is controlling the DAI) and as such
wont have set a minimum number of playback or capture channels required for BE
DAI registration (to establish supported stream directions).
Force machine drivers to explicitly set whether they support playback and capture
stream directions for every BE DAIs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the platform driver has no ops, the platform function
bespoke_trigger() is no more called.
The problem was introduced by the commit c5914b0aae
"ASoC: pcm: Check for ops before deferencing them"
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though we might not have rigor rule for the simple card property names,
according to the existing ones, they are all in a same pattern:
[simple-audio-card,]XXX;
Rename simple-audio-routing to simple-audio-card,routing, and make the simple
card's properties has one unified name.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We no longer have a means to differentiate between MSP devices at probe
time, mainly because we don't really have to. So rather than have an over-
sized static data structure in place, where the only difference between
devices is the ID and name (which are unused), we'll just create one
succinct, statically assigned and shared one instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If booting with full DT support (i.e. DMA too, the last piece of the
puzzle), then we don't need to use the compatible_request_channel call
back or require some of the historical bumph which probably isn't
required by a platform data start-up now either. This will also be
ripped out in upcoming commits.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In this patch we do two things. Firstly, instead of open coding the
store of DMA data in to the DAI for later use, we use the API provided.
Secondly we create and store similar DMA data for the DT case, only
this time we use 'struct snd_dmaengine_dai_dma_data' which is provided
by the core for this very reason.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Soon we will strip out pdata support from the Ux500 set of ASoC drivers.
When this happens it will have to supply a DMA slave_config to the
dmaengine. At the moment a great deal of this comes from pdata via
AUXDATA. We need to become independent of this soon. This patch starts
the process by allocating memory for the associated data structures and
fetches the MSP id used for const struct indexing.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for full Device Tree enablement we must differentiate
between the two varying ways DMA data can be held in the DAI store. If
we're booting with Device Tree the provided 'snd_dmaengine_dai_dma_data'
data structure shall be used, whereas in order to avoid breaking legacy
platform data we also need to be able to translate DMA data stored using
the UX500 specific 'ux500_msp_dma_params' method.
Once we move over to solely use Device Tree, we can enforce the use of
'snd_dmaengine_dai_dma_data' and this code can be removed altogether.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Slave Config's addr_width attribute is populated by data_width of
dma_cfg, which in turn is derived from dma_params' data_size attribute
and that comes from the slot_width which is always 16 bits (2 Bytes).
We're cutting out the middle man here and just setting the DMA Slave
Config directly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We're getting closer to fully enabling the Ux500 ASoC driver for Device
Tree. When we switch over from using AUXDATA we'll need to match platform
by only Device Tree nodes. In this patch we NULL out the platform_name,
and supply nodes for each platform device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
These drivers will not work without platform specific data, which is
passed in via Device Tree or Platform Data. To avoid the chance of
NULL pointer dereferencing and alike, let's ensure we have at least
one of the methods in play before continuing.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 7b11304 ("dma: mxs-dma: Report correct residue for cyclic DMA")
the mxs dmaengine driver has support for residue reporting. So there is no need
to specify the SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag anymore. This allows a
finer grained resolution for the PCM pointer as well as avoids the race
condition that can occur with the period counting that is used when the
dmaengine driver does not support residue reporting.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6873ee464a (ASoC: fsl_ssi: Fix printing return code on clk error) caused
the following build warning:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1196:6: warning: format '%d' expects argument of type 'int', but argument 3 has type 'long int' [-Wformat]
Fix it by using '%ld' to print the 'long int' format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow PCMs that do not impose any restrictions on the supported formats to set
the formats field to 0, Instead of assuming that this means that the PCM does
not support any formats (which doesn't make much sense), assume that it supports
all formats. This brings the behavior of DPCM closer to that of non-DPCM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for initializing the runtime pcm on both the playback and
the capture path. Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a trivial cleanup: remove useless variable mc13xxx and
extra spaces. No functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are no users of this driver without pdata, so stop using
constant assignment of ADC and DAC ports.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
mc13783-codec is probed only by MC13XXX MFD core driver so
use module_platform_driver_probe().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit f0e9c080 - "ALSA: compress: change the way sample rates are sent to
kernel" changed the way sample rates are sent. So now we don't need to check for
PCM_RATE_xxx in kernel
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev;
@@
pci_set_power_state(pdev,
- 3
+ PCI_D3hot
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This motherboard seems to have a flaky jack detection - when the
front HP is not present, the jack state quickly switches on and off.
This has been reported by three people in the bug, so I doubt it's
a user error this time.
BugLink: https://bugs.launchpad.net/bugs/1248116
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not a lot going on framework wise, partly due to Christmas at least in
the case of the work I've been doing, but there's been quite a lot of
cleanup activity going on and the usual trickle of new drivers:
- Update to the generic DMA code to support deferred probe and managed
resources.
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs.
- Device tree support for the simple card, max98090 and cs42l52.
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more modern
and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi.
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=jhuo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.14
Not a lot going on framework wise, partly due to Christmas at least in
the case of the work I've been doing, but there's been quite a lot of
cleanup activity going on and the usual trickle of new drivers:
- Update to the generic DMA code to support deferred probe and managed
resources.
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs.
- Device tree support for the simple card, max98090 and cs42l52.
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more modern
and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi.
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi.
ffs() returns the bit position from 1, while the ssm2158 driver code
assumes it being 0-based. Also, the bit mask computation of the two
channel slots are incorrect; it must have worked just casually.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to get the device's module clock if the dt has no clocks and
system-clock-frequency properties.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a quick fix for the below two issues when building spdif as modules.
1) If modprobing modules in order: (Step 1) snd-soc-fsl-spdif -> (Step 2)
snd-soc-imx-spdif -> (Step 3) snd-soc-spdif-tx/rx, we will fail to create
imx-spdif card and dai link unless we rmmod snd-soc-imx-spdif and modprobe
it again due to the execution platform_driver_unregister() in probe() when
meeting -EPROBE_DEFER at Step 2.
2) After "imx-spdif sound-spdif.17: dit-hifi <-> 2004000.spdif mapping ok",
'rmmod snd-soc-imx-spdif' would cause kernel dump with warning:
WARNING: CPU: 0 PID: 1301 at /home/rmk/git/linux-rmk/fs/sysfs/dir.c:915 sysfs_hash_and_remove+0x84/0x90()
sysfs: can not remove 'dapm_widget', no directory
This should be caused by disordered resourse releasing of the whole link.
And trying to unregister the card and then CODEC dev can't fix this issue.
Thus this patch just provides a simple fix to these two bugs by using the
snd-soc-dummy in the core instead of seperate snd-soc-spdif-tx/rx so that
there's no need to handle the registering and unregistering of CODEC or
CODEC dai any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
From "ASoC: make snd_soc_dai_link more symmetrical", can we see that
the name of CPU DAI maybe omitted. If the DAI name is omitted, try to
use the component name instead.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds SRC support to Renesas sound driver.
SRC converts sampling rate between codec <-> cpu.
It needs special codec chip,
or very simple DA/AD converter to use it.
This patch was tested via ak4554 codec,
and supports Gen1 only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
ssi clock which is calculated from rsnd_ssi_master_clk_start()
should have flexibility since Renesas sound has
SRC (= Sampling Rate Converter).
But current implementation is using runtime->rate directly.
This patch tidyup rsnd_ssi_master_clk_start() parameter
as preparation of future SRC support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
rsnd_scu_set_hpbif() is renamed to rsnd_scu_rate_ctrl(),
since its naming doesn't indicate the function meaning.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
INT_ENABLE is needed only Gen2.
rsnd_mod_write() do nothing on Gen1, but it is confusable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
SRC_CTRL/BUSIF_MODE are used for transfer start.
This patch adds rsnd_scu_transfer_start() and merge these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
rsnd_scu_set_route() is needed only Gen1.
This patch renames it to rsnd_scu_set_route_if_gen1()
and it adds comment to rsnd_reg member
in order to clarify it is used for Gen1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is assuming that
RBGA is used as source clock of 44.1kHz category, and
RBGB is used as source clock of 48kHz category.
This patch clarifies the variable name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use correct register name which appears in the datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
we can check rsnd_ssi_init(), not, rsnd_ssi_start()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds rsnd_adg_set_ssi_clk() to access to
AUDIO_CLK_SEL0/1/2, and removes last user of
rsnd_write/read/bset which is very low level function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When call snd_soc_register_card, it will set driver data to this
device through dev_set_drvdata, then in driver, no need to call
platform_set_drvdata again, so remove it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Revert the SAI's endianess for fifo data to/from DMA engine.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is maybe one bug or a limitation of the hardware that the {T,R}CR2's
Synchronous Mode bits must be set as late as possible, or the SAI device
maybe hanged up, and there has not any explaination about this limitation
in the SAI Data Sheet.
And the {T,R}CR2's Synchronous Mode bits must be set at the same time whether
for Tx or Rx stream.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enables/Disables the corresponding data channel for tx/rx operation.
A channel must be enabled before its FIFO is accessed, and then disable
it when tx/rx is stopped or idle.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 5d229ce569 ("ASoC: samsung: move plat/ headers to local directory")
moved the header files but forgot to clean the pointers to their old locaton.
Remove them now.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Because we cannot make sure which one of _dai_fmt() and _dai_sysclk()
will be firstly called. So move the RCSR/TCSR and TCR1/RCR1's
initialization to _dai_probe(), and this can make sure that before any
of {T,R}CR{1~5} register to be set the RCSR/TCSR's RE/TE bit has been
cleared for the hareware limitation.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown