Add support to SET_DELAY_DROP command.
This command will be used in downstream patches for delay packet drop.
The timeout value should be indicated by delay_drop_timeout field.
Packet processing will be delayed till timeout value passed or until
more WQEs are posted.
Setting this value to 0 disables the feature.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for raw ethernet local loopback firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The offending commit pushed fwd the field by two bits but
didn't increment the offset, fix that. Currently, no damage
was done b/c this is just a field name, but lets have it right.
Fixes: f32f5bd2eb ('net/mlx5: Configure cache line size for start and end padding')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For environments where flow-based ipv6 router is offloaded.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enable offloading of TC matching on ip ttl / hop-limit
As matching on ttl is supported only by newer HW brands (ConnectX-5),
we should do capability check before attempting to offload that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding a support to flush all HW resources with one FW command and
skip all the heavy unload flows of the driver on kernel shutdown.
There's no need to free all the SW context since a new fresh kernel
will be loaded afterwards.
Regarding the FW resources, they should be closed, otherwise we will
have leakage in the FW. To accelerate this flow, we execute one command
in the beginning that tells the FW that the driver isn't going to close
any of the FW resources and asks the FW to clean up everything.
Once the commands complete, it's safe to close the PCI resources and
finish the routine.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fixed few places where endianness was misspelled and
one spot whwere output was:
CHECK: 'endianess' may be misspelled - perhaps 'endianness'?
CHECK: 'ouput' may be misspelled - perhaps 'output'?
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read port connector type from the firmware instead of caching it in the
driver metadata.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update struct mlx5_ifc_create(modify)_flow_table_bits according to
the last device specification.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
HW can implement UMR wqe re-transmission in various ways.
Thus, add HCA cap to distinguish the needed fence for UMR to make
sure that the wqe wouldn't fail on mkey checks.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Mellanox Innova is a NIC with ConnectX and an FPGA on the same
board. The FPGA is a bump-on-the-wire and thus affects operation of
the mlx5_core driver on the ConnectX ASIC.
Add basic support for Innova in mlx5_core.
This allows using the Innova card as a regular NIC, by detecting
the FPGA capability bit, and verifying its load state before
initializing ConnectX interfaces.
Also detect FPGA fatal runtime failures and enter error state if
they ever happen.
All new FPGA-related logic is placed in its own subdirectory 'fpga',
which may be built by selecting CONFIG_MLX5_FPGA.
This prepares for further support of various Innova features in later
patchsets.
Additional details about hardware architecture will be provided as
more features get submitted.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add port_xmit_wait to the error counters read by mlx5_ib_process_mad to
ensure sysfs port counter provides correct value for PortXmitWait.
Otherwise the sysfs port_xmit_wait file always contains zero.
The previous MAD_IFC implementation populated this counter, but it was
removed during the migration to PPCNT for error counters (32-bit only).
Signed-off-by: Tim Wright <tim@binbash.co.uk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds support to query the congestion related hardware counters
through new command and links them with other hw counters being available
in hw_counters sysfs location.
In order to reuse existing infrastructure it renames related q_counter
data structures to more generic counters to reflect q_counters and
congestion counters and maybe some other counters in the future.
New hardware counters:
* rp_cnp_handled - CNP packets handled by the reaction point
* rp_cnp_ignored - CNP packets ignored by the reaction point
* np_cnp_sent - CNP packets sent by notification point to respond to
CE marked RoCE packets
* np_ecn_marked_roce_packets - CE marked RoCE packets received by
notification point
It also avoids returning ENOSYS which is specific for invalid
system call and produces the following checkpatch.pl warning.
WARNING: ENOSYS means 'invalid syscall nr' and nothing else
+ return -ENOSYS;
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This change adds the ability for flow steering to classify IPv4/6
packets with MPLS tag (Ethertype 0x8847 and 0x8848) as standard IP
packets and hit IPv4/6 classifed steering rules.
When user added a flow rule with IP classification, driver was
implicitly adding ethertype matching to the created rule in order
to distinguish between IPv4 and IPv6 protocols.
Since IP packets with MPLS tag header have MPLS ethertype, they missed
the rule and ended up hitting the default filters.
Such behavior prevented from MPLS packets to undergo inbound traffic
load balancing flows (if such were defined by configuring RSS) to
achieve higher throughput - the way that non-MPLS IP packets performed.
Since our device is able to look past the MPLS tag and identify the
next protocol we introduce this solution which replaces Ethertype
matching by the device's capability to perform IP version parsing
and matching in order to distinguish between IPv4 and IPv6.
Therefore, whenever a flow with IP spec is added and device support IP
version matching, driver will implicitly add IP version matching to the
rule (Based on the IP spec type) without Ethertype matching which will
cause relevant MPLS tagged packets to hit this rule as well.
Otherwise (device doesn't support IP version matching), we fall back to
setting Ethertype matching.
If the user's filters specify an L2 ethertype and an IP spec
the rule will then match both the ethertype and the IP version.
The device's support for IP version matching is reported by the
device via dedicated capability bit in query_device_cap and named
outer/inner_ip_version.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
New capability bit: ipoib_enhanced_offloads, indicates new ability for UD
QP to do RSS and enhanced IPoIB offloads and acceleration.
Add underlay_qpn to the TIS and flow_table objects In order to support
SET_ROOT command, to connect between IPoIB QPs and flow steering tables.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for rx-fcs flag from ethtool.
In case this flag is set, update all RQs to scatter the FCS data into
the packet.
Signed-off-by: Guy Ergas <guye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the definitions related to creation/deletion of a modify header
context and the modify header steering action which are used for HW
packet header modify (re-write) as part of steering. Add as well the
modify header id into two intermediate structs and set it to the FTE.
Note that as the push/pop vlan steering actions are emulated by the
ewitch management code, we're not breaking any compatibility while
changing their values to make room for the modify header action which
is not emulated and whose value is part of the FW API. The new bit
values for the emulated actions are at the end of the possible range.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Because the Mellanox code required being based on a net-next tree,
I keept it separate from the remainder of the RDMA stack submission
that is based on 4.10-rc3.
This branch contains:
- Various mlx4 and mlx5 fixes and minor changes
- Support for adding a tag match rule to flow specs
- Support for cvlan offload operation for raw ethernet QPs
- A change to the core IB code to recognize raw eth capabilities and
enumerate them (touches non-Mellanox code)
- Implicit On-Demand Paging memory registration support
-----BEGIN PGP SIGNATURE-----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=rspQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull Mellanox rdma updates from Doug Ledford:
"Mellanox specific updates for 4.11 merge window
Because the Mellanox code required being based on a net-next tree, I
keept it separate from the remainder of the RDMA stack submission that
is based on 4.10-rc3.
This branch contains:
- Various mlx4 and mlx5 fixes and minor changes
- Support for adding a tag match rule to flow specs
- Support for cvlan offload operation for raw ethernet QPs
- A change to the core IB code to recognize raw eth capabilities and
enumerate them (touches non-Mellanox code)
- Implicit On-Demand Paging memory registration support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (40 commits)
IB/mlx5: Fix configuration of port capabilities
IB/mlx4: Take source GID by index from HW GID table
IB/mlx5: Fix blue flame buffer size calculation
IB/mlx4: Remove unused variable from function declaration
IB: Query ports via the core instead of direct into the driver
IB: Add protocol for USNIC
IB/mlx4: Support raw packet protocol
IB/mlx5: Support raw packet protocol
IB/core: Add raw packet protocol
IB/mlx5: Add implicit MR support
IB/mlx5: Expose MR cache for mlx5_ib
IB/mlx5: Add null_mkey access
IB/umem: Indicate that process is being terminated
IB/umem: Update on demand page (ODP) support
IB/core: Add implicit MR flag
IB/mlx5: Support creation of a WQ with scatter FCS offload
IB/mlx5: Enable QP creation with cvlan offload
IB/mlx5: Enable WQ creation and modification with cvlan offload
IB/mlx5: Expose vlan offloads capabilities
IB/uverbs: Enable QP creation with cvlan offload
...
Counters weren't updated due to Receive WQs' traffic since the
counter-id was not associated with the RQ.
Added support for associating the q-counter-id with the Receive WQ.
The attachment is done only when changing WQ's state from RESET to
READY in modify-WQ command.
FW support is required for the above, without this support
Receive WQ counters will not count.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add new TX WQE fields for Connect-X5 vlan insertion support,
type and vlan_tci, when type = MLX5_ETH_WQE_INSERT_VLAN the
HW will insert the vlan and prio fields (vlan_tci) to the packet.
Those bits and the inline header fields are mutually exclusive, and
valid only when:
MLX5_CAP_ETH(mdev, wqe_inline_mode) == MLX5_CAP_INLINE_MODE_NOT_REQUIRED
and MLX5_CAP_ETH(mdev, wqe_vlan_insert),
who will be set in ConnectX-5 and later HW generations.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
There is a hardware feature that will pad the start or end of a DMA to
be cache line aligned to avoid RMWs on the last cache line. The default
cache line size setting for this feature is 64B. This change configures
the hardware to use 128B alignment on systems with 128B cache lines.
In addition we lower bound MPWRQ stride by HCA cacheline in mlx5e,
MPWRQ stride should be at least the HCA cacheline, the current default
is 64B and in case HCA_CAP.cach_line_128byte capability is set, MPWRQ RX
stride will automatically be aligned to 128B.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for SRIOV VF min rate guarantee by using the TSAR BW share
weights mechanism.
The TSAR BW share vport attribute represents the weight of that vport
among the other vports weights which means that the actual vport BW
percentage is the same vport weight percentage among the total vports
weights sum.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the needed infrastructure for future use of MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the needed infrastructure for future use of PPCNT physical layer
statistical group.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
PCAM: Ports capabilities mask register.
MCAM: Management capabilities mask register.
PCAM and MCAM registers will provide information regarding firmware
support for different features, in order to avoid cases where new driver
combined with old firmware results in syndromes (for ex. PCIe counters
before this patchset).
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement query and set functionality for MTPPS and MTPPSE registers.
MTPPS (Management Pulse Per Second) provides the device PPS capabilities,
configures the PPS in and out modules and holds the PPS in time stamp.
Query MTPPS is supported only when HCA_CAP.pps is set and modify is supported
when HCA_CAP.pps_modify is set.
MTPPSE (Management Pulse Per Second Event) configures the different event
generation modes for PPS. Supported when HCA_CAP.pps is set.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The following series of patches optimizes the usage of the UAR area which is
contained within the BAR 0-1. Previous versions of the firmware and the driver
assumed each system page contains a single UAR. This patch set will query the
firmware for a new capability that if published, means that the firmware can
support UARs of fixed 4K regardless of system page size. In the case of
powerpc, where page size equals 64KB, this means we can utilize 16 UARs per
system page. Since user space processes by default consume eight UARs per
context this means that with this change a process will need a single system
page to fulfill that requirement and in fact make use of more UARs which is
better in terms of performance.
In addition to optimizing user-space processes, we introduce an allocator
that can be used by kernel consumers to allocate blue flame registers
(which are areas within a UAR that are used to write doorbells). This provides
further optimization on using the UAR area since the Ethernet driver makes
use of a single blue flame register per system page and now it will use two
blue flame registers per 4K.
The series also makes changes to naming conventions and now the terms used in
the driver code match the terms used in the PRM (programmers reference manual).
Thus, what used to be called UUAR (micro UAR) is now called BFREG (blue flame
register).
In order to support compatibility between different versions of
library/driver/firmware, the library has now means to notify the kernel driver
that it supports the new scheme and the kernel can notify the library if it
supports this extension. So mixed versions of libraries can run concurrently
without any issues.
Thanks,
Eli and Matan
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYc9kSAAoJEEg/ir3gV/o+a0EH/jEGiopH7CHc4T4nXT1I4kQa
TicrkMNV3Sr9MBWwn8TLOyx+Fi1dex4cumrJI/BNVjC6h/nS6JHbslYoZxTkX9lT
L0vRsHJBVr/PODqimIGNnlJFBPhNJSGiHG4JHlJHlpvcGNahitN3gXmUjcRNju+V
ExnvgwWzAXM0qg1qWf5A/3HmqbtYES1rJXQUsimtc2QAif/SIayBD4fEA8x5zNBA
i0p8xcDrzUqmeblkpnsJA3w40s1rsuqvJnvLPDpbpKENtHfw1UFZ2987P7LvOrIv
NF/mZBkStC0gOZX6dLEAdoZXL1gTsJX19hTkUMfYH4BHqHARa2/oCS3wcCf1Giw=
=C+cp
-----END PGP SIGNATURE-----
Merge tag 'mlx5-4kuar-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5 4K UAR
The following series of patches optimizes the usage of the UAR area which is
contained within the BAR 0-1. Previous versions of the firmware and the driver
assumed each system page contains a single UAR. This patch set will query the
firmware for a new capability that if published, means that the firmware can
support UARs of fixed 4K regardless of system page size. In the case of
powerpc, where page size equals 64KB, this means we can utilize 16 UARs per
system page. Since user space processes by default consume eight UARs per
context this means that with this change a process will need a single system
page to fulfill that requirement and in fact make use of more UARs which is
better in terms of performance.
In addition to optimizing user-space processes, we introduce an allocator
that can be used by kernel consumers to allocate blue flame registers
(which are areas within a UAR that are used to write doorbells). This provides
further optimization on using the UAR area since the Ethernet driver makes
use of a single blue flame register per system page and now it will use two
blue flame registers per 4K.
The series also makes changes to naming conventions and now the terms used in
the driver code match the terms used in the PRM (programmers reference manual).
Thus, what used to be called UUAR (micro UAR) is now called BFREG (blue flame
register).
In order to support compatibility between different versions of
library/driver/firmware, the library has now means to notify the kernel driver
that it supports the new scheme and the kernel can notify the library if it
supports this extension. So mixed versions of libraries can run concurrently
without any issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is an implementation of an allocator that allocates blue flame
registers. A blue flame register is used for generating send doorbells.
A blue flame register can be used to generate either a regular doorbell
or a blue flame doorbell where the data to be sent is written to the
device's I/O memory hence saving the need to read the data from memory.
For blue flame kind of doorbells to succeed, the blue flame register
need to be mapped as write combining. The user can specify what kind of
send doorbells she wishes to use. If she requested write combining
mapping but that failed, the allocator will fall back to non write
combining mapping and will indicate that to the user.
Subsequent patches in this series will make use of this allocator.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Handle ODP atomic operations. When initiator of RDMA atomic
operation use ODP MR to provide source data handle pagefault properly.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update PAGE_FAULT_RESUME command layout.
Three bit fields describing page fault: rdma, rdma_write, req_res gave 8
possible combinations, while only a few were legal. Now they
are interpreted as three-bit type field, where former legal
combinations turns into corresponding types and unused were added as new
types.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following items to IFC file.
1. MLX5_MKC_ACCESS_MODE_KSM enum value for creating KSM memory keys.
KSM access mode used when indirect MKey associated with fixed memory
size entries.
2. null_mkey field that is used to indicate non-present KLM/KSM
entries, where it causes the device to generate page fault event
when trying to access it.
3. struct mlx5_ifc_cmd_hca_cap_bits capability bits indicating
related value/field is supported:
* fixed_buffer_size - MLX5_MKC_ACCESS_MODE_KSM
* umr_extended_translation_offset - translation_offset_42_16
in UMR ctrl segment
* null_mkey - null_mkey in QUERY_SPECIAL_CONTEXTS
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix offset for reserved fields.
Fixes: 7486216b3a ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: b4ff3a36d3 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Fixes: 7d5e14237a ("net/mlx5: Update mlx5_ifc hardware features")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Shared mlx5 updates with net stack (will drop out on merge if Dave's
tree has already been merged)
- Driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- Debug cleanups
- New connection rejection helpers
- SRP updates
- Various misc fixes
- New paravirt driver from vmware
-----BEGIN PGP SIGNATURE-----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=QeGy
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
Multi packet WQE enables sending multiple fix sized packets
using a single WQE. The exposed field reports such HW support.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add the needed infrastructure for future use of MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver_version capability bit is enabled, and set driver
version command in mlx5_ifc firmware header. The only purpose
of this command is to store a driver version/OS string in FW
to be reported and displayed in various management systems,
such as IPMI/BMC.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware structures and constants definitions needed for module
events support.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSAR (stands for Transmit Scheduling ARbiter) is a hardware component
that is responsible for selecting the next entity to serve on the
transmit path.
The arbitration defines the QoS policy between the agents connected to
the TSAR.
The TSAR is a consist two main features:
1) BW Allocation between agents:
The TSAR implements a defecit weighted round robin between the agents.
Each agent attached to the TSAR is assigned with a weight and it is
awarded transmission tokens according to this weight.
2) Rate limer per agent:
Each agent attached to the TSAR is (optionally) assigned with a rate
limit.
TSAR will not allow scheduling for an agent exceeding its defined rate
limit.
In this patch we implement the API of manipulating the TSAR.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Update struct mlx5_ifc_xrqc_bits according to last specification
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous an_disable_cap position bit31 is deprecated to be use in driver
with newer firmware. New firmware will advertise the same capability
in bit29.
Old capability didn't allow setting more than one protocol for a
specific speed when autoneg is off, while newer firmware will allow
this and it is indicated in the new capability location.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware capabilities for sniffer
RX and TX flow tables.
Add the following capabilities:
1. Sniffer RX flow table capabilities.
2. Sniffer TX flow table capabilities.
3. If same TIR can be used by multiple flow tables of different types.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Exposed LAG commands enum and layouts:
- CREATE_LAG
HW enters LAG mode:
RoCE traffic from port two is received on PF0 core dev.
Allows to set tx_affinity (tx port) for QPs and TISes.
Allows to port remap QPs and TISes, overriding their
tx_affinity behavior.
- MODIFY_LAG
Remap QPs and TISes to another port.
- QUERY_LAG
Query whether LAG mode is active.
- DESTROY_LAG
HW exits LAG mode, returning to non-LAG behavior.
- CREATE_VPORT_LAG
Merge Ethernet flow steering, such that traffic received on port
two jumps to PF0 root flow table.
Available only in LAG mode.
- DESTROY_VPORT_LAG
Ethernet flow steering returns to non-LAG behavior.
Caps added:
- lag_master
Driver is in charge of managing the LAG.
This is currently the only option.
- num_lag_ports
LAG is supported only if this field's value is 2.
Other fields:
- QP/TIS tx port affinity
During LAG, this field controls on which port a QP or TIS resides.
- TIS strict tx affinity
When this field is set, the TIS will not be subject to port remap by
CREATE_LAG/MODIFY_LAG.
- LAG demux flow table
Flow table used for redirecting non user-space traffic back to
PF1 root flow table, if the packet was received on port two.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Update struct mlx5_ifc_xrqc_bits according to last specification
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Use mlx5 ifc MODIFY_BITMASK_VSD in mlx5e_modify_rq_vsd and expose counter
set capability bit in hca caps structure.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add the required definitions related to vxlan encap/decap.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implement the low-level part of the PF side in setting minimum
inline header mode for VFs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created QP/XRCD commands layout
amd use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created MKey/PSV commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created MCG commands layout
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add support for query the minimum inline mode from the Firmware.
It is required for correct TX steering according to L3/L4 packet
headers.
Each send queue (SQ) has inline mode that defines the minimal required
headers that needs to be copied into the SQ WQE.
The driver asks the Firmware for the wqe_inline_mode device capability
value. In case the device capability defined as "vport context" the
driver must check the reported min inline mode from the vport context
before creating its SQs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit utilize the ability of ConnectX-4 to bulk read flow counters.
Few bulk counter queries could be done instead of issuing thousands of
firmware commands per second to get statistics of all flows set to HW,
such as those programmed when we offload tc filters.
Counters are stored sorted by hardware id, and queried in blocks (id +
number of counters).
Due to hardware requirement, start of block and number of counters in a
block must be four aligned.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Mellanox mlx5_core shared code for both net-next and RDMA
trees for 4.8 kernel cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=93xr
-----END PGP SIGNATURE-----
Merge tag 'shared' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Mellanox shared code between RDMA and net-next trees
This is Mellanox mlx5_core shared code for both net-next and RDMA
trees for 4.8 kernel cycle.
Introducing mlx5_ifc updates for upcoming ConnectX-4 features.
Needed bits and hardware structures for mlx5e netdev:
- MLX5_CQ_PERIOD_NUM_MODES for adaptive moderation
support
- QoS rate limiting
- SQ context rate limiting
- Auto negotiation fields in PTYS register
- Source SQN field in flow table entry match structure
- DCBX parameters
Needed bits and hardware structures for IB:
- New XRQ opcodes, commands and capabilities layout
- Extend q counters definition to support IB.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In RoCE, the RDMA-CM needs the node guid to establish connection
between nodes.
Today, the node guid exposed to mlx5 Ethernet VFs is zero, therefore
RDMA-CM on the VF is broken.
Whenever the administrator sets a MAC for a VF, derive the node guid
from it and set it as well in the following way:
MAC: e4:1d:2d:b3:f4:01 -> node_guid: e4:1d:2d:ff:fe:b3:f4:01
Fixes: 77256579c6 ('net/mlx5: E-Switch, Introduce Vport...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having MLX5_CMD_OP_MAX on another file causes us to repeatedly miss
accounting new commands added to the driver and hence there're no entries
for them in debugfs. To solve that, we integrate it into the commands enum
as the last entry.
Fixes: 34a40e6893 ('net/mlx5_core: Introduce modify flow table command')
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the needed mlx5_ifc hardware bits and structs
for the following feature:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, baeacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b084444459 ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
Implement the IB defined callbacks used to manipulate the policy for the
link state, set GUIDs or get statistics information. This functionality
is added into a new file that will be used to add any SRIOV related
functionality to the mlx5 IB layer.
The following callbacks have been added:
mlx5_ib_get_vf_config
mlx5_ib_set_vf_link_state
mlx5_ib_get_vf_stats
mlx5_ib_set_vf_guid
In addition, publish whether this device is based on a virtual function.
In mlx5 supported devices, virtual functions are implemented as vHCAs.
vHCAs have their own QP number space so it is possible that two vHCAs
will use a QP with the same number at the same time.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Define the necessary hardware structures for the offload
arithmetic capabilities and read/cache them on driver load.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
- cxgb4 updates
- nes updates
- unification of iwarp portmapper code to core
- add drain_cq API
- various ib_core updates
- minor ipoib updates
- minor mlx4 updates
- more significant mlx5 updates (including a minor merge conflict with
net-next tree...merge is simple to resolve and Stephen's resolution was
confirmed by Mellanox)
- trivial net/9p rdma conversion
- ocrdma RoCEv2 update
- srpt updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kTkT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.6 merge window patches.
This is the first of two pull requests. It is the smaller request,
but touches for more different things (this is everything but what is
in or going into staging). The pull request for the code in
staging/rdma is on hold until after we decide what to do on the
write/writev API issue and may be partially deferred until 4.7 as a
result.
Summary:
- cxgb4 updates
- nes updates
- unification of iwarp portmapper code to core
- add drain_cq API
- various ib_core updates
- minor ipoib updates
- minor mlx4 updates
- more significant mlx5 updates (including a minor merge conflict
with net-next tree...merge is simple to resolve and Stephen's
resolution was confirmed by Mellanox)
- trivial net/9p rdma conversion
- ocrdma RoCEv2 update
- srpt updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (85 commits)
iwpm: crash fix for large connections test
iw_cxgb3: support for iWARP port mapping
iw_cxgb4: remove port mapper related code
iw_nes: remove port mapper related code
iwcm: common code for port mapper
net/9p: convert to new CQ API
IB/mlx5: Add support for don't trap rules
net/mlx5_core: Introduce forward to next priority action
net/mlx5_core: Create anchor of last flow table
iser: Accept arbitrary sg lists mapping if the device supports it
mlx5: Add arbitrary sg list support
IB/core: Add arbitrary sg_list support
IB/mlx5: Expose correct max_fast_reg_page_list_len
IB/mlx5: Make coding style more consistent
IB/mlx5: Convert UMR CQ to new CQ API
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Delete unnecessary variable initialisations in 11 functions
IB/core: Documentation fix in the MAD header file
IB/core: trivial prink cleanup.
...
Add support to create flow rule that forward packets
to the first flow table in the next priority (next priority
could be the first priority in the next namespace or the
next priority in the same namespace).
This feature could be used for DONT_TRAP rules or rules
that only want to mark the packet with flow tag.
In order to do it optimally, each flow table has list
of all rules that point to this flow table,
when a flow table is destroyed/created, we update the list
head correspondingly.
This kind of rule is created when destination is NULL and
action is MLX5_FLOW_CONTEXT_ACTION_FWD_NEXT_PRIO.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds user-space support for memory windows allocation and
deallocation. It also exposes the supported types via
query_device_caps verb.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Tested-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to create multiple GSI QPs, we need to set the source QP number to
one on all these QPs. Add the necessary definitions and infrastructure to
do that.
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The HW can supply several offloads for UD QP, added offloads for
checksumming for both TX and RX and LSO for TX.
Two new bits were added in order to expose and enable these offloads:
1. HCA capability bit: declares the support for IPoIB basic offloads.
2. QPC bit which will be used in the QP creation flow, which set these
abilities in the QP.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Added helper function to read IB standard error counters
via the PPCNT register.
The PPCNT register read command provides the 32-bit error counters
of both IB/RoCE link layer and transport layer.
Signed-off-by: Meny Yossefi <menyy@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_0[0x1];
u8 srq_receive[0x1];
u8 reserved_1[0x1a];
};
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_at_4[0x1];
u8 srq_receive[0x1];
u8 reserved_at_6[0x1a];
};
This makes the conflicts much more rare and preserves the locality of
changes.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed through the
RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to dependencies,
acknowledged by Bruce)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oO7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
When the user changes the Address Vector(AV) in the modify QP, he
provides an SL. This SL should be translated to Ethernet Priority
by taking the 3 LSB bits, and modify the QP's TIS according to this
Ethernet priority.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change the mlx5 firmware interface header to make it
more clear which bytes should be used by IPv4 or
IPv6 addresses.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the modify flow table command. This command is used when
we want to change the next flow table of an existing flow table.
The next flow table is defined as the table we search (in order
to find a match), if we couldn't find a match in any of the flow table
entries in the current flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root Flow Table for each Flow Table Type is defined,
by default, as the Flow Table with level 0.
In order not to use an empty flow tables and introduce new hops,
but still preserve space for flow-tables that have a priority
greater(lower number) than the current flow table, we introduce this
new set root flow table command.
This command tells the HW to start matching packets from the
assigned root flow table.
This command is used when we create new flow table with level lower than the
current lowest flow table or it is the first flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW is capable of 2 requestor endianness modes for standard 8 Bytes
atomic: BE (0x0) and host endianness (0x1). Read the supported modes
from hca atomic capabilities and configure HW to host endianness mode if
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reporting the hca_core_clock (in kHZ) and the timestamp_mask in
query_device extended verb. timestamp_mask is used by users in order
to know what is the valid range of the raw timestamps, while
hca_core_clock reports the clock frequency that is used for
timestamps.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.
The E-Switch manager can access (read/modify) any of its vports
E-Switch context.
Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling E-Switch SRIOV for nvfs+1 vports.
Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).
FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmached Traffic (src vport != Uplink) -> Uplink.
Unmached Traffic (src vport == Uplink) -> vport0(PF).
FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.
Preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch
preparation for ethernet sriov.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update HCA capabilities and HW struct to include needed
capabilities for upcoming Ethernet Switch (SR-IOV E-Switch).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.
Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb