Add bond_ether_setup helper which is used to fix ether_setup() calls in the
bonding driver. It takes care of both IFF_MASTER and IFF_SLAVE flags, the
former is always restored and the latter only if it was set.
If the bond enslaves non-ARPHRD_ETHER device (changes its type), then
releases it and enslaves ARPHRD_ETHER device (changes back) then we
use ether_setup() to restore the bond device type but it also resets its
flags and removes IFF_MASTER and IFF_SLAVE[1]. Use the bond_ether_setup
helper to restore both after such transition.
[1] reproduce (nlmon is non-ARPHRD_ETHER):
$ ip l add nlmon0 type nlmon
$ ip l add bond2 type bond mode active-backup
$ ip l set nlmon0 master bond2
$ ip l set nlmon0 nomaster
$ ip l add bond1 type bond
(we use bond1 as ARPHRD_ETHER device to restore bond2's mode)
$ ip l set bond1 master bond2
$ ip l sh dev bond2
37: bond2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether be:d7:c5:40:5b:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
(notice bond2's IFF_MASTER is missing)
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ff9fb72bc0 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
Fixes: ff9fb72bc0 ("debugfs: return error values, not NULL")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20230202093256.32458-1-zhengqi.arch@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Almost all validation logic is in the drivers, but they are
missing reliable way to convey failure reason to userspace
applications.
Let's use extack to return this information to users.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Otherwise we would dereference a NULL aggregator pointer when calling
__set_agg_ports_ready on the line below.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_miimon_commit() is run while RTNL is held, not RCU.
WARNING: suspicious RCU usage
6.1.0-syzkaller-09671-g89529367293c #0 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:2704 suspicious rcu_dereference_check() usage!
Fixes: e95cc44763 ("bonding: do failover when high prio link up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Link: https://lore.kernel.org/r/20221220130831.1480888-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, when a high prio link enslaved, or when current link down,
the high prio port could be selected. But when high prio link up, the
new active slave reselection is not triggered. Fix it by checking link's
prio when getting up. Making the do_failover after looping all slaves as
there may be multi high prio slaves up.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 0a2ff7cc8a ("Bonding: add per-port priority for failover re-selection")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is one direct accesses to bond->curr_active_slave in
bond_miimon_commit(). Protected it by rcu_access_pointer()
since the later of this function also use this one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, in bonding it reused the IFF_SLAVE flag and checked it
in ipv6 addrconf to prevent ipv6 addrconf.
However, it is not a proper flag to use for no ipv6 addrconf, for
bonding it has to move IFF_SLAVE flag setting ahead of dev_open()
in bond_enslave(). Also, IFF_MASTER/SLAVE are historical flags
used in bonding and eql, as Jiri mentioned, the new devices like
Team, Failover do not use this flag.
So as Jiri suggested, this patch adds IFF_NO_ADDRCONF in priv_flags
of the device to indicate no ipv6 addconf, and uses it in bonding
and moves IFF_SLAVE flag setting back to its original place.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 4d633d1b46 ("bonding: fix ICMPv6 header handling when receiving
IPv6 messages"), there is a copy/paste issue for NA daddr. I found that
in my testing and fixed it in my local branch. But I forgot to re-format
the patch and sent the wrong mail.
Fix it by reading the correct dest address.
Fixes: 4d633d1b46 ("bonding: fix ICMPv6 header handling when receiving IPv6 messages")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20221206032055.7517-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "ignore_updelay" variable needs to be initialized to false.
Fixes: f8a65ab2f3 ("bonding: fix link recovery in mode 2 when updelay is nonzero")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/Y4SWJlh3ohJ6EPTL@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Before this change when a bond in mode 2 lost link, all of its slaves
lost link, the bonding device would never recover even after the
expiration of updelay. This change removes the updelay when the bond
currently has no usable links. Conforming to bonding.txt section 13.1
paragraph 4.
Fixes: 41f8910040 ("bonding: ignore updelay param when there is no active slave")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, we get icmp6hdr via function icmp6_hdr(), which needs the skb
transport header to be set first. But there is no rule to ask driver set
transport header before netif_receive_skb() and bond_handle_frame(). So
we will not able to get correct icmp6hdr on some drivers.
Fix this by using skb_header_pointer to get the IPv6 and ICMPV6 headers.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 4e24be018e ("bonding: add new parameter ns_targets")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20221118034353.1736727-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bond agnostically interacts with TLS device-offload requests via the
.ndo_sk_get_lower_dev operation. Return value is true iff bond
guarantees fixed mapping between the TLS connection and a lower netdev.
Due to this nature, the bond TLS device offload features are not
explicitly controllable in the bond layer. As of today, these are
read-only values based on the evaluation of bond_sk_check(). However,
this indication might be incorrect and misleading, when the feature bits
are "fixed" by some dependency features. For example,
NETIF_F_HW_TLS_TX/RX are forcefully cleared in case the corresponding
checksum offload is disabled. But in fact the bond ability to still
offload TLS connections to the lower device is not hurt.
This means that these bits can not be trusted, and hence better become
unused.
This patch revives some old discussion [1] and proposes a much simpler
solution: Clear the bond's TLS features bits. Everyone should stop
reading them.
[1] https://lore.kernel.org/netdev/20210526095747.22446-1-tariqt@nvidia.com/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221025105300.4718-1-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for 800Gbps speed to allow using 3ad mode with 800G devices.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The bonding driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former bond
slaves after a bond has been deleted; see test_LAG_cleanup() in the last
patch in this series.
Add unsync calls, via bond_hw_addr_flush(), at their expected location,
bond_close().
Add dev_mc_add() call to bond_open() to match the above change.
v3:
* When adding or deleting a slave, only sync/unsync, add/del addresses if
the bond is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are already a few definitions of arrays containing
MULTICAST_LACPDU_ADDR and the next patch will add one more use. These all
contain the same constant data so define one common instance for all
bonding code.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The unsolicited NA message with all-nodes multicast dest address should
be valid, as this also means the link could reach the target.
Also rename bond_validate_ns() to bond_validate_na().
Reported-by: LiLiang <liali@redhat.com>
Fixes: 5e1eeef69c ("bonding: NS target should accept link local address")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ns_ip6_target was set, the ipv6_dev_get_saddr() will be called to get
available source address and send IPv6 neighbor solicit message.
If the target is global address, ipv6_dev_get_saddr() will get any
available src address. But if the target is link local address,
ipv6_dev_get_saddr() will only get available address from our interface,
i.e. the corresponding bond interface.
But before bond interface up, all the address is tentative, while
ipv6_dev_get_saddr() will ignore tentative address. This makes we can't
find available link local src address, then bond_ns_send() will not be
called and no NS message was sent. Finally bond interface will keep in
down state.
Fix this by sending NS with unspecified address if there is no available
source address.
Reported-by: LiLiang <liali@redhat.com>
Fixes: 5e1eeef69c ("bonding: NS target should accept link local address")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value is only ever set once in bond_3ad_initialize and only ever
read otherwise. There seems to be no reason to set the variable via
bond_3ad_initialize when setting the global variable will do. Change
ad_ticks_per_sec to a const to enforce its read-only usage.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is caused by the global variable ad_ticks_per_sec being zero as
demonstrated by the reproducer script discussed below. This causes
all timer values in __ad_timer_to_ticks to be zero, resulting
in the periodic timer to never fire.
To reproduce:
Run the script in
`tools/testing/selftests/drivers/net/bonding/bond-break-lacpdu-tx.sh` which
puts bonding into a state where it never transmits LACPDUs.
line 44: ip link add fbond type bond mode 4 miimon 200 \
xmit_hash_policy 1 ad_actor_sys_prio 65535 lacp_rate fast
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 48: ip link set fbond address 52:54:00:3B:7C:A6
setting bond MAC addr
call stack:
bond->dev->dev_addr = new_mac
line 52: ip link set fbond type bond ad_actor_sys_prio 65535
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 60: ip link set veth1-bond down master fbond
given:
params.ad_actor_system = 0
params.mode = BOND_MODE_8023AD
ad.system.sys_mac_addr == bond->dev->dev_addr
call stack:
bond_enslave
-> bond_3ad_initialize(); because first slave
-> if ad.system.sys_mac_addr != bond->dev->dev_addr
return
results:
Nothing is run in bond_3ad_initialize() because dev_addr equals
sys_mac_addr leaving the global ad_ticks_per_sec zero as it is
never initialized anywhere else.
The if check around the contents of bond_3ad_initialize() is no longer
needed due to commit 5ee14e6d33 ("bonding: 3ad: apply ad_actor settings
changes immediately") which sets ad.system.sys_mac_addr if any one of
the bonding parameters whos set function calls
bond_3ad_update_ad_actor_settings(). This is because if
ad.system.sys_mac_addr is zero it will be set to the current bond mac
address, this causes the if check to never be true.
Fixes: 5ee14e6d33 ("bonding: 3ad: apply ad_actor settings changes immediately")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d5410ac7b0 ("net:bonding:support balance-alb interface
with vlan to bridge") introduced a reference count leak by not releasing
the reference acquired by ip_dev_find(). Remedy this by insuring the
reference is released.
Fixes: d5410ac7b0 ("net:bonding:support balance-alb interface with vlan to bridge")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/26758.1660194413@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, tls_device_down synchronizes with tls_device_resync_rx using
RCU, however, the pointer to netdev is stored using WRITE_ONCE and
loaded using READ_ONCE.
Although such approach is technically correct (rcu_dereference is
essentially a READ_ONCE, and rcu_assign_pointer uses WRITE_ONCE to store
NULL), using special RCU helpers for pointers is more valid, as it
includes additional checks and might change the implementation
transparently to the callers.
Mark the netdev pointer as __rcu and use the correct RCU helpers to
access it. For non-concurrent access pass the right conditions that
guarantee safe access (locks taken, refcount value). Also use the
correct helper in mlx5e, where even READ_ONCE was missing.
The transition to RCU exposes existing issues, fixed by this commit:
1. bond_tls_device_xmit could read netdev twice, and it could become
NULL the second time, after the NULL check passed.
2. Drivers shouldn't stop processing the last packet if tls_device_down
just set netdev to NULL, before tls_dev_del was called. This prevents a
possible packet drop when transitioning to the fallback software mode.
Fixes: 89df6a8104 ("net/bonding: Implement TLS TX device offload")
Fixes: c55dcdd435 ("net/tls: Fix use-after-free after the TLS device goes down and up")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Link: https://lore.kernel.org/r/20220810081602.1435800-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In my test, balance-alb bonding with two slaves eth0 and eth1,
and then Bond0.150 is created with vlan id attached bond0.
After adding bond0.150 into one linux bridge, I noted that Bond0,
bond0.150 and bridge were assigned to the same MAC as eth0.
Once bond0.150 receives a packet whose dest IP is bridge's
and dest MAC is eth1's, the linux bridge will not match
eth1's MAC entry in FDB, and not handle it as expected.
The patch fix the issue, and diagram as below:
eth1(mac:eth1_mac)--bond0(balance-alb,mac:eth0_mac)--eth0(mac:eth0_mac)
|
bond0.150(mac:eth0_mac)
|
bridge(ip:br_ip, mac:eth0_mac)--other port
Suggested-by: Hu Yadi <huyd12@chinatelecom.cn>
Signed-off-by: Sun Shouxin <sunshouxin@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver piggybacks on time stamps kept by the network stack
for the purpose of the netdev TX watchdog, and this is problematic
because it does not work with NETIF_F_LLTX devices.
It is hard to say why the driver looks at dev_trans_start() of the
slave->dev, considering that this is updated even by non-ARP/NS probes
sent by us, and even by traffic not sent by us at all (for example PTP
on physical slave devices). ARP monitoring in active-backup mode appears
to still work even if we track only the last TX time of actual ARP
probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
The KASAN logs are as follows:
[ 767.617392] ==================================================================
[ 767.630776] BUG: KASAN: use-after-free in bond_3ad_state_machine_handler+0x13dc/0x1470
[ 767.638764] Read of size 2 at addr ffff00011ba9d430 by task kworker/u8:7/767
[ 767.647361] CPU: 3 PID: 767 Comm: kworker/u8:7 Tainted: G O 5.15.11 #15
[ 767.655329] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 767.660760] Workqueue: lacp_1 bond_3ad_state_machine_handler
[ 767.666468] Call trace:
[ 767.668930] dump_backtrace+0x0/0x2d0
[ 767.672625] show_stack+0x24/0x30
[ 767.675965] dump_stack_lvl+0x68/0x84
[ 767.679659] print_address_description.constprop.0+0x74/0x2b8
[ 767.685451] kasan_report+0x1f0/0x260
[ 767.689148] __asan_load2+0x94/0xd0
[ 767.692667] bond_3ad_state_machine_handler+0x13dc/0x1470
Fixes: 0622cab034 ("bonding: fix 802.3ad aggregator reselection")
Co-developed-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220629012914.361-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding ARP monitor fails to decrement send_peer_notif, the
number of peer notifications (gratuitous ARP or ND) to be sent. This
results in a continuous series of notifications.
Correct this by decrementing the counter for each notification.
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: b0929915e0 ("bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor")
Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/9400.1655407960@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setting RLB_NULL_INDEX is not needed as this is done in bond_alb_initialize
which is called by bond_open.
Also reduce the number of rtnl_unlock calls by just using the standard
goto cleanup path.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for reporting errors via extack in both bond_newlink
and bond_changelink.
Instead of having to look in the kernel log for why an option was not
correct just report the error to the user via the extack variable.
What is currently reported today:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
RTNETLINK answers: Device or resource busy
After this change:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
Error: unable to set option because the bond is up.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().
Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.
Fixes: 4e24be018e ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When adding bond new parameter ns_targets. I forgot to print this
in bond master proc info. After updating, the bond master info will look
like:
ARP IP target/s (n.n.n.n form): 192.168.1.254
NS IPv6 target/s (XX::XX form): 2022::1, 2022::2
Fixes: 4e24be018e ("bonding: add new parameter ns_targets")
Reported-by: Li Liang <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220530062639.37179-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When setting bond NS target, we use bond_is_ip6_target_ok() to check
if the address valid. The link local address was wrongly rejected in
bond_changelink(), as most time the user just set the ARP/NS target to
gateway, while the IPv6 gateway is always a link local address when user
set up interface via SLAAC.
So remove the link local addr check when setting bond NS target.
Fixes: 129e3c1bab ("bonding: add new option ns_ip6_target")
Reported-by: Li Liang <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the rcu_read_lock in bond_ethtool_get_ts_info() as
discussed [1], I didn't notice it could be called via setsockopt,
which doesn't hold rcu lock, as syzbot pointed:
stack backtrace:
CPU: 0 PID: 3599 Comm: syz-executor317 Not tainted 5.18.0-rc5-syzkaller-01392-g01f4685797a5 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
bond_option_active_slave_get_rcu include/net/bonding.h:353 [inline]
bond_ethtool_get_ts_info+0x32c/0x3a0 drivers/net/bonding/bond_main.c:5595
__ethtool_get_ts_info+0x173/0x240 net/ethtool/common.c:554
ethtool_get_phc_vclocks+0x99/0x110 net/ethtool/common.c:568
sock_timestamping_bind_phc net/core/sock.c:869 [inline]
sock_set_timestamping+0x3a3/0x7e0 net/core/sock.c:916
sock_setsockopt+0x543/0x2ec0 net/core/sock.c:1221
__sys_setsockopt+0x55e/0x6a0 net/socket.c:2223
__do_sys_setsockopt net/socket.c:2238 [inline]
__se_sys_setsockopt net/socket.c:2235 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2235
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f8902c8eb39
Fix it by adding rcu_read_lock and take a ref on the real_dev.
Since dev_hold() and dev_put() can take NULL these days, we can
skip checking if real_dev exist.
[1] https://lore.kernel.org/netdev/27565.1642742439@famine/
Reported-by: syzbot+92beb3d46aab498710fa@syzkaller.appspotmail.com
Fixes: aa6034678e ("bonding: use rcu_dereference_rtnl when get bonding active slave")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220519020148.1058344-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces some sk_ipv6only tests with ipv6_only_sock().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov