Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to recurse into filesystem from the memory
allocation, which deadlocks in xfs_qm_shake(). Add check
for __GFP_FS, and bail out if it is not set.
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Hedi Berriche <hedi@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
In the case where growing a filesystem would leave the last AG
too small, the fixup code has an overflow in the calculation
of the new size with one fewer ag, because "nagcount" is a 32
bit number. If the new filesystem has > 2^32 blocks in it
this causes a problem resulting in an EINVAL return from growfs:
# xfs_io -f -c "truncate 19998630180864" fsfile
# mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile
# mount -o loop fsfile /mnt
# xfs_growfs /mnt
meta-data=/dev/loop0 isize=256 agcount=52,
agsize=76288719 blks
= sectsz=512 attr=2
data = bsize=4096 blocks=3905982455, imaxpct=5
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=32768, version=2
= sectsz=512 sunit=0 blks, lazy-count=0
realtime =none extsz=4096 blocks=0, rtextents=0
xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument
Reported-by: richard.ems@cape-horn-eng.com
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Regreesion from commit ef8f7fc, which rearranged the code in
xfs_swap_extents() leading to double unlock of xfs inode ilock.
That resulted in xfs_fsr deadlocking itself on platforms, which
don't handle double unlock of rw_semaphore nicely. It caused the
count go negative, which represents the write holder, without
really having one. ia64 is one of the platforms where deadlock
was easily reproduced and the fix was tested.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
A race was found that if one were to enable and disable the function
profiler repeatedly, then the system can panic. This was because a profiled
function may be preempted just before disabling interrupts. While
the profiler is disabled and then reenabled, the preempted function
could start again, and access the hash as it is being initialized.
This just adds a check in the irq disabled part to check if the profiler
is enabled, and if it is not then it will just exit.
When the system is disabled, the profile_enabled variable is cleared
before calling the unregistering of the function profiler. This
unregistering calls stop machine which also acts as a synchronize schedule.
[ Impact: fix panic in enabling/disabling function profiler ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The trace_pipe did not recognize the latency format flag and would produce
different output than the trace file. The problem was partly due that
the trace flags in the iterator was not set as well as the trace_pipe
zeros out part of the iterator (including the flags) to be able to use
the same routines as the trace file. trace_flags of the iterator should
not cause any problems when not zeroed out by for trace_pipe.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
After converting the softirq tracer to use te flags options, this
caused a regression with the name. Since the flag was used directly
it was printed out (i.e. HRTIMER_SOFTIRQ).
This patch only shows the softirq name without the SOFTIRQ part.
[ Impact: fix regression of output from softirq events ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A patch to allow the use of __print_symbolic and __print_flags
from a module. This allows the current GFS2 tracing patch to
build.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
LKML-Reference: <1243868015.29604.542.camel@localhost.localdomain>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
__string() is limited:
- it's a char array, but we may want to define array with other types
- a source string should be available, but we may just know the string size
We introduce __dynamic_array() to break those limitations, and __string()
becomes a wrapper of it. As a side effect, now __get_str() can be used
in TP_fast_assign but not only TP_print.
Take XFS for example, we have the string length in the dirent, but the
string itself is not NULL-terminated, so __dynamic_array() can be used:
TRACE_EVENT(xfs_dir2,
TP_PROTO(struct xfs_da_args *args),
TP_ARGS(args),
TP_STRUCT__entry(
__field(int, namelen)
__dynamic_array(char, name, args->namelen + 1)
...
),
TP_fast_assign(
char *name = __get_str(name);
if (args->namelen)
memcpy(name, args->name, args->namelen);
name[args->namelen] = '\0';
__entry->namelen = args->namelen;
),
TP_printk("name %.*s namelen %d",
__entry->namelen ? __get_str(name) : NULL
__entry->namelen)
);
[ Impact: allow defining dynamic size arrays ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A2384D2.3080403@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently TP_fast_assign has a limitation that we can't define local
variables in it.
Here's one use case when we introduce __dynamic_array():
TP_fast_assign(
type *p = __get_dynamic_array(item);
foo(p);
bar(p);
),
[ Impact: allow defining local variables in TP_fast_assign ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A2384B1.90100@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Both event tracer and sched switch plugin are selected by default
by all generic tracers. But if no generic tracer is enabled, their options
appear. But ether one of them will select the other, thus it only
makes sense to have the default tracers be selected by one option.
[ Impact: clean up kconfig menu ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There are two options that are selected by all tracers, but we want
to have those options available when no tracer is selected. These are
The event tracer and sched switch tracer.
The are enabled by all tracers, but if a tracer is not selected we want
the options to appear. All tracers including them select TRACING.
Thus what we would like to do is:
config EVENT_TRACER
bool "prompt"
depends on TRACING
select TRACING
But that gives us a bug in the kbuild system since we just created a
circular dependency. We only want the prompt to show when TRACING is off.
This patch adds GENERIC_TRACER that all tracers will select instead of
TRACING. The two options (sched switch and event tracer) will select
TRACING directly and depend on !GENERIC_TRACER. This solves the cicular
dependency.
[ Impact: hide options that are selected by default ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When using ftrace=function on the command line to trace functions
on boot up, one can not filter out functions that are commonly called.
This patch adds two new ftrace command line commands.
ftrace_notrace=function-list
ftrace_filter=function-list
Where function-list is a comma separated list of functions to filter.
The ftrace_notrace will make the functions listed not be included
in the function tracing, and ftrace_filter will only trace the functions
listed.
These two act the same as the debugfs/tracing/set_ftrace_notrace and
debugfs/tracing/set_ftrace_filter respectively.
The simple glob expressions that are allowed by the filter files can also
be used by the command line interface.
ftrace_notrace=rcu*,*lock,*spin*
Will not trace any function that starts with rcu, ends with lock, or has
the word spin in it.
Note, if the self tests are enabled, they may interfere with the filtering
set by the command lines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Fix SCI transmission sequence in console output function.
This reorders the write sequence to match the SH-3 manual, and corrects
a console corruption bug observed on SH-3 SCI.
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_SH_PCLK_FREQ=33333333 is correct for sh7724.
sh7724 master clock is 33333333, but peripheral is 41666666.
This bug came to light because sh-sci driver had changed clk
from "module_clk" to "peripheral_clk"
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the fact that the IOAPIC version number in the x86_64 code path always
gets assigned to 0, instead of the correct value.
Before the patch: (from "dmesg" output):
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 <---
After the patch:
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 <---
History:
io_apic_get_version() was compiled out of the x86_64 code path in the commit
f2c2cca3acef8b253a36381d9b469ad4fb08563a:
Author: Andi Kleen <ak@suse.de>
Date: Tue Sep 26 10:52:37 2006 +0200
[PATCH] Remove APIC version/cpu capability mpparse checking/printing
ACPI went to great trouble to get the APIC version and CPU capabilities
of different CPUs before passing them to the mpparser. But all
that data was used was to print it out. Actually it even faked some data
based on the boot cpu, not on the actual CPU being booted.
Remove all this code because it's not needed.
Cc: len.brown@intel.com
At the time, the IOAPIC version number was deliberately not printed
in the x86_64 code path. However, after the x86 and x86_64 files were
merged, the net result is that the IOAPIC version is printed incorrectly
in the x86_64 code path.
The patch below provides a fix. I have tested it with acpi, and with
acpi=off, and did not see any problems.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <20090416014230.4885.94926.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
*************************
register_stat_tracer() uses list_for_each_entry_safe
to check whether a tracer is already present in the list.
But we don't delete anything from the list here, so
we don't need the safe version
[ Impact: cleanup list use is stat tracing ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
- remove duplicate code in stat_seq_init()
- update comments to reflect the change from stat list to stat rbtree
[ Impact: clean up ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
When closing a trace_stat file, we destroy the rbtree constructed during
file open, but there is memory leak that the root node is not freed.
[ Impact: fix memory leak when closing a trace_stat file ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Currently the output of trace_stat/workqueues is totally reversed:
# cat /debug/tracing/trace_stat/workqueues
...
1 17 17 210 37 `-blk_unplug_work+0x0/0x57
1 3779 3779 181 11 |-cfq_kick_queue+0x0/0x2f
1 3796 3796 kblockd/1:120
...
The correct output should be:
1 3796 3796 kblockd/1:120
1 3779 3779 181 11 |-cfq_kick_queue+0x0/0x2f
1 17 17 210 37 `-blk_unplug_work+0x0/0x57
It's caused by "tracing/stat: replace linked list by an rbtree for
sorting"
(53059c9b67a62a3dc8c80204d3da42b9267ea5a0).
dummpy_cmp() should return -1, so rb_node will always be inserted as
right-most node in the rbtree, thus we sort the output in ascending
order.
[ Impact: fix the output of trace_stat/workqueues ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
When the stat tracing framework prepares the entries from a tracer
to output them to the user, it starts by computing a linear sort
through a linked list to give the entries ordered by relevance
to the user.
This is quite ugly and causes a small latency when we begin to
read the file.
This patch changes that by turning the linked list into a red-black
tree. Athough the whole iteration using the start and next tracer
callbacks while opening the file remain the same, it is now much
more fast and scalable.
The rbtree guarantees O(log(n)) insertions whereas a linked
list with linear sorting brought us a O(n) despair. Now the
(visible) latency has disapeared.
[ Impact: kill the latency while starting to read a stat tracer file ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The "trace" prefix in struct trace_stat_session type is annoying while
reading the trace_stat.c file. It makes the lines longer, and
is not that much useful to explain the sense of this type.
Just keep "struct stat_session" for this type.
[ Impact: make the code a bit more readable ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The blankline between each cpu's workqueue stat is not necessary, because
the cpu number is enough to part them by eye.
Old style also caused a blankline below headline, and made code complex
by using lock, disableirq and get cpu var.
Old style:
# CPU INSERTED EXECUTED NAME
# | | | |
0 8644 8644 events/0
0 0 0 cpuset
...
0 1 1 kdmflush
1 35365 35365 events/1
...
New style:
# CPU INSERTED EXECUTED NAME
# | | | |
0 8644 8644 events/0
0 0 0 cpuset
...
0 1 1 kdmflush
1 35365 35365 events/1
...
[ Impact: provide more readable code ]
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
cpu_workqueue_stats->first_entry is useless because we can retrieve the
header of a cpu workqueue using:
if (&cpu_workqueue_stats->list == workqueue_cpu_stat(cpu)->list.next)
[ Impact: cleanup ]
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
No need to use list_for_each_entry_safe() in iteration without deleting
any node, we can use list_for_each_entry() instead.
[ Impact: cleanup ]
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
v3: zhaolei@cn.fujitsu.com: Change TRACE_EVENT definition to new format
introduced by Steven Rostedt: consolidate trace and trace_event headers
v2: kosaki@jp.fujitsu.com: print the function names instead of addr, and zap
the work addr
v1: zhaolei@cn.fujitsu.com: Make workqueue tracepoints use TRACE_EVENT macro
TRACE_EVENT is a more generic way to define tracepoints.
Doing so adds these new capabilities to the tracepoints:
- zero-copy and per-cpu splice() tracing
- binary tracing without printf overhead
- structured logging records exposed under /debug/tracing/events
- trace events embedded in function tracer output and other plugins
- user-defined, per tracepoint filter expressions
Then, this patch converts DEFINE_TRACE to TRACE_EVENT in workqueue related
tracepoints.
[ Impact: expand workqueue tracer to events tracing ]
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Merge reason: irq/numa didnt build because this commit:
2759c32: x86: don't call read_apic_id if !cpu_has_apic
Had a dependency on x86/cpufeature changes. Pull in that
(small) branch to fix the dependency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add fan_max description.
Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This tidies up the boot_cpu_data.flags probing on SH-4A. All of them have
a few things in common, which we can blindly set, rather than having each
subtype have to set the same flags. We can also make assumptions about
cache ways and the validity of PTEA, so this also kills off CPU_HAS_PTEA
as a config option. There was also a bug in the FPU probing, which is now
tidied up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up the L2 probing, as it may or may not be implemented on a
CPU, regardless of whether it is supported. This converts the cvr
validity checks from BUG_ON()'s to simply clearing the CPU_HAS_L2_CACHE
flag and moving on with life.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds me as the maintainer of the CPMAC (AR7)
Ethernet driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add shared code for 4-bit divisor clocks.
Processor specific code can use SH_CLK_DIV4()
to initialize div4 clocks, and then use
sh_clk_div4_register() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Neil Horman