Adds an ACPI companion to the KEMPLD I2C driver so that it correctly
detects any I2C devices nested under the KEMPLD's ACPI node (SBRG.CPLD).
This allows I2C devices attached to the KEMPLD I2C adapter to be declared
and instantiated via ACPI.
Signed-off-by: Chris Pringle <chris.pringle@phabrix.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8188 and added mt_i2c_regs_v3[], since
MT8188 i2c OFFSET_SLAVE_ADDR register changed from 0x04 to 0x94.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A late ack is currently being sent at the end of a transfer due to
incorrect logic in mchp_corei2c_empty_rx(). Currently the Assert Ack
bit is being written to the controller's control reg after the last
byte has been received, causing it to sent another byte with the ack.
Instead, the AA flag should be written to the control register when
the penultimate byte is read so it is sent out for the last byte.
Reported-by: Andreas Buerkler <andreas.buerkler@enclustra.com>
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Tested-by: Lewis Hanly <lewis.hanly@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[wsa: fixed typos in commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix i2c transfers using GPI DMA mode for all message types that do not set
the I2C_M_DMA_SAFE flag (e.g. SMBus "read byte").
In this case a bounce buffer is returned by i2c_get_dma_safe_msg_buf(),
and it has to synced back to the message after the transfer is done.
Add missing assignment of dma buffer in geni_i2c_gpi().
Set xferred in i2c_put_dma_safe_msg_buf() to true in case of no error to
ensure the sync-back of this dma buffer to the message.
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Robin Reckmann <robin.reckmann@gmail.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Highlights:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop Studio
- thinkpad_acpi: AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Fix acpi_video_handles_brightness_key_presses()
- video: Change how we determine if brightness key-presses are handled
Documentation/ABI:
- Add new attributes for mlxreg-io sysfs interfaces
- mlxreg-io: Fix contact info
Drop the PMC_ATOM Kconfig option:
- Drop the PMC_ATOM Kconfig option
EDAC, pnd2:
- convert to use common P2SB accessor
- Use proper I/O accessors and address space annotation
HID:
- surface-hid: Add support for hot-removal
ISST:
- PUNIT device mapping with Sub-NUMA clustering
Kconfig:
- Remove unnecessary "if X86"
MAINTAINERS:
- repair file entry in MICROSOFT SURFACE AGGREGATOR TABLET-MODE SWITCH
Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans:
- Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans
Move AMD platform drivers to separate directory:
- Move AMD platform drivers to separate directory
acer-wmi:
- Use backlight helper
acer_wmi:
- Cleanup Kconfig selects
apple-gmux:
- Use backlight helper
asus-wmi:
- Add mic-mute LED classdev support
- Add key mappings
compal-laptop:
- Use backlight helper
efi:
- Fix efi_power_off() not being run before acpi_power_off() when necessary
gigabyte-wmi:
- add support for B660I AORUS PRO DDR4
hp-wmi:
- Ignore Sanitization Mode event
i2c:
- i801: convert to use common P2SB accessor
ideapad-laptop:
- Add Ideapad 5 15ITL05 to ideapad_dytc_v4_allow_table[]
- Add allow_v4_dytc module parameter
intel/pmc:
- Add Alder Lake N support to PMC core driver
intel_atomisp2_led:
- Also turn off the always-on camera LED on the Asus T100TAF
leds:
- simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
- simatic-ipc-leds: Convert to use P2SB accessor
mfd:
- lpc_ich: Add support for pinctrl in non-ACPI system
- lpc_ich: Switch to generic p2sb_bar()
- lpc_ich: Factor out lpc_ich_enable_spi_write()
mlx-platform:
- Add COME board revision register
- Add support for new system XH3000
- Introduce support for COMe NVSwitch management module for Vulcan chassis
- Add support for systems equipped with two ASICs
- Add cosmetic changes for alignment
- Make activation of some drivers conditional
p2sb:
- Move out of X86_PLATFORM_DEVICES dependency
panasonic-laptop:
- Use acpi_video_get_backlight_type()
- filter out duplicate volume up/down/mute keypresses
- don't report duplicate brightness key-presses
- revert "Resolve hotkey double trigger bug"
- sort includes alphabetically
- de-obfuscate button codes
pinctrl:
- intel: Check against matching data instead of ACPI companion
platform/mellanox:
- mlxreg-lc: Fix error flow and extend verbosity
- mlxreg-io: Add locking for io operations
- nvsw-sn2201: fix error code in nvsw_sn2201_create_static_devices()
platform/olpc:
- Fix uninitialized data in debugfs write
platform/surface:
- gpe: Add support for 13" Intel version of Surface Laptop 4
- tabletsw: Fix __le32 integer access
- Update copyright year of various drivers
- aggregator: Move subsystem hub drivers to their own module
- aggregator: Move device registry helper functions to core module
- aggregator_registry: Add support for tablet mode switch on Surface Laptop Studio
- aggregator_registry: Add support for tablet mode switch on Surface Pro 8
- Add KIP/POS tablet-mode switch driver
- aggregator: Add helper macros for requests with argument and return value
- aggregator: Reserve more event- and target-categories
- avoid flush_scheduled_work() usage
- aggregator_registry: Add support for keyboard cover on Surface Pro 8
- aggregator_registry: Add KIP device hub
- aggregator_registry: Change device ID for base hub
- aggregator_registry: Generify subsystem hub functionality
- aggregator: Add comment for KIP subsystem category
- aggregator_registry: Use client device wrappers for notifier registration
- aggregator: Allow notifiers to avoid communication on unregistering
- aggregator: Allow devices to be marked as hot-removed
- aggregator: Allow is_ssam_device() to be used when CONFIG_SURFACE_AGGREGATOR_BUS is disabled
platform/x86/amd/pmc:
- Add new platform support
- Add new acpi id for PMC controller
platform/x86/dell:
- Kconfig: Remove unnecessary "depends on X86_PLATFORM_DEVICES"
platform/x86/intel:
- Add Primary to Sideband (P2SB) bridge support
platform/x86/intel/ifs:
- Mark as BROKEN
platform/x86/intel/pmt:
- telemetry: Fix fixed region handling
platform/x86/intel/vsec:
- Fix wrong type for local status variables
- Add PCI error recovery support to Intel PMT
- Add support for Raptor Lake
- Rework early hardware code
pmc_atom:
- Fix comment typo
- Match all Lex BayTrail boards with critclk_systems DMI table
power/supply:
- surface_battery: Use client device wrappers for notifier registration
- surface_charger: Use client device wrappers for notifier registration
serial-multi-instantiate:
- Sort ACPI IDs by HID
- Get rid of redundant 'else'
- Use while (i--) pattern to clean up
- Improve dev_err_probe() messaging
- Drop duplicate check
- Improve autodetection
simatic-ipc:
- drop custom P2SB bar code
sony-laptop:
- Remove useless comparisons in sony_pic_read_possible_resource()
system76_acpi:
- Use dev_get_drvdata
thinkpad_acpi:
- Enable AMT by default on supported systems
- Add support for hotkey 0x131a
- Add support for automatic mode transitions
- profile capabilities as integer
- do not use PSC mode on Intel platforms
- Fix a memory leak of EFCH MMIO resource
- Replace custom str_on_off() etc
- Sort headers for better maintenance
- Use backlight helper
tools/power/x86/intel-speed-select:
- Remove unneeded semicolon
- Fix off by one check
watchdog:
- simatic-ipc-wdt: convert to use P2SB accessor
x86-android-tablets:
- Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmLrndEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zeMgf7BjSCz6ZA8SSY1i8QHDTvdjySihHJ
j07Gn3j1T/5G00R/r6viMDE4PxcYvMAPXjq3azepKQd8H5kGfE323SA6fgWFPAvi
P2OvEfvWfI5S8FYGYPBkNP2MjQ5MFe7qzLEh3+wQH0ocJ7WRCi457B4Xvtd2gWI3
dHj5gMSWC3O5xNa2S4Mg3dnD9uJlwhX+FNjWIuRy8eh5+DikgByyC4B+uW6WtO5e
t0rmIm6q5wUzB7dIetJLoAQwrcpYAOkK7L33G9h/7knWAfiJfklaKTbftnoxbDSv
iGWODkLDyob4C48DmVusS6WMEhPUzl/R33+tk6LjVt/YOYOP030EMtCECQ==
=Krhc
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop
Studio
- thinkpad_acpi:
- AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
platform/x86/intel/vsec: Fix wrong type for local status variables
platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
platform/x86: pmc_atom: Fix comment typo
platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
platform/olpc: Fix uninitialized data in debugfs write
platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
tools/power/x86/intel-speed-select: Remove unneeded semicolon
tools/power/x86/intel-speed-select: Fix off by one check
platform/surface: tabletsw: Fix __le32 integer access
Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
Documentation/ABI: mlxreg-io: Fix contact info
platform/mellanox: mlxreg-io: Add locking for io operations
platform/x86: mlx-platform: Add COME board revision register
platform/x86: mlx-platform: Add support for new system XH3000
platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
platform/x86: mlx-platform: Add support for systems equipped with two ASICs
platform/x86: mlx-platform: Add cosmetic changes for alignment
platform/x86: mlx-platform: Make activation of some drivers conditional
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
-----BEGIN PGP SIGNATURE-----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=6fXH
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers: Microchip CoreI2C, Renesas RZV2M
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
* tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: extend documentation about retvals of master_xfer functions
i2c: mux-gpmux: Add of_node_put() when breaking out of loop
dt-bindings: i2c: i2c-rk3x: Document Rockchip RV1126
i2c: qcom-geni: Use the correct return value
i2c: cadence: Support PEC for SMBus block read
i2c: qcom-geni: Propagate GENI_ABORT_DONE to geni_i2c_abort_xfer()
i2c: brcmstb: Use dev_name() for adapter name
i2c: Add Renesas RZ/V2M controller
dt-bindings: i2c: Document RZ/V2M I2C controller
i2c: mlxcpld: Add callback to notify probing completion
i2c: scmi: Replace open coded device_get_match_data()
i2c: stm32: add support for the STM32MP13 soc
dt-bindings: i2c: st,stm32-i2c: add entry for stm32mp13
dt-bindings: i2c: i2c-rk3x: add rk3588 compatible
i2c: add support for microchip fpga i2c controllers
i2c: i801: Add support for Intel Meteor Lake-P
dt-bindings: i2c: nomadik: Add power domain to binding
dt-bindings: i2c: nomadik: Drop unused voltage supply from example
i2c: Fix a potential use after free
i2c: hisi: use HZ_PER_KHZ macro in units.h
...
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The introduction of GPI support moved things around and instead of
returning the result from geni_i2c_xfer() the number of messages in the
request was returned, ignoring the actual result. Fix this.
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Waiting for M_CMD_ABORT_EN in geni_i2c_abort_xfer() races with the
interrupt handler which will read and clear the abort bit, the result is
that every abort attempt takes 1 second and is followed by a message
about the abort having times out.
Introduce a new state variable to carry the abort_done state from the
interrupt handler back to geni_i2c_abort_xfer(). Also, turn NACK
and TIMEOUT errors into debug messages
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
[wsa: squashed two patches into one]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This make it easier to disambiguate the different i2c controllers
present in a system, and then correlating with /proc/interrupts allows
to know which instance is interrupt driven and which one is not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Yet another i2c controller from Renesas that is found on the RZ/V2M
(r9a09g011) SoC. It can support only 100kHz and 400KHz operation.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
[wsa: removed superfluous class type and renamed a function]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add notification to inform caller that driver probing has been
completed. It allows to user, invoked platform device registration for
"i2c-mlxcpld" driver, to be notified that bus adapter is available, and
thus some devices could be connected to this bus.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Problems were observed on the Xilinx ZynqMP platform with large I2C reads.
When a read of 277 bytes was performed, the controller NAKed the transfer
after only 252 bytes were transferred and returned an ENXIO error on the
transfer.
There is some code in cdns_i2c_master_isr to handle this case by resetting
the transfer count in the controller before it reaches 0, to allow larger
transfers to work, but it was conditional on the CDNS_I2C_BROKEN_HOLD_BIT
quirk being set on the controller, and ZynqMP uses the r1p14 version of
the core where this quirk is not being set. The requirement to do this to
support larger reads seems like an inherently required workaround due to
the core only having an 8-bit transfer size register, so it does not
appear that this should be conditional on the broken HOLD bit quirk which
is used elsewhere in the driver.
Remove the dependency on the CDNS_I2C_BROKEN_HOLD_BIT for this transfer
size reset logic to fix this problem.
Fixes: 63cab195bf ("i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace open coded device_get_match_data() in acpi_smbus_cmi_add().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add a new compatible for the stm32mp13. Fast Mode Plus control
register address differ from the one for STM32MP15.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
to provid --> to provide
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAmLMTtEACgkQh9CWnEQH
BwSmNw/+KC2qMPJ7e1favA8joQ+YCOWht3URTLDNrWpFrkAWLqjEkeYfSJQ3fBns
vhDs42nt3318GZKa0YRFkttHEG4ZB5eV4pcf1GGV2/BtnUjr3tgD8iEIDLYeq8Z1
Y1F5WVXrCx3ta+xADVy1MMIM82ycWjKsrF7f8iADdP/hJtrlpnEdhOIzqz8Az5g+
ezFrs66/P0X+tc/a41mZ1BHIXa/4nnibo+A+hT/gtDK0g4uv/94XaQVaAn3VvELx
m/RgkQsrKed3xGnniz9N+LX9oQ/IHQzz6HxZD3TokKlTS1rjHr0YMb++jo0430na
NQ45Y9U0gl3gwalN+85YTabA0VWkVdkzn0YGydmcrJqphm3s78M+/FiMddaVQtMv
D4ndLVqr6LXTKtsZIk97shuuxMHMaix5mA2hOOWFO0TjQFzsKOi/k2uZ0mo9hBPC
FMsetOjmoeA1e01ztuW/3T2yQH1CQkHow/lp1xoidvLzgALraK3wAdhMX0lIR5Fg
bxPNkrj1mTHPcBO7C7DKbvXt7bybZcn624/55FrTaYu5p0BdaazshMUHKBUb1l5K
lhB4znh9dKQwc94VGdHzNISEjZSpjRbdnqBr/1qzpwR6SGR9jMFS1wTcjK2iAyMz
iUR+O3vEeyOfRz2rSkgGSYIqkxdCX4Q6jyk4wz56gYP8FfIqmQ8=
=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
I2C_BRCMSTB depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch ensures that the clock notifier is unregistered
when driver probe is returning error.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Satish Nagireddy <satish.nagireddy@getcruise.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add Microchip CoreI2C i2c controller support. This driver supports the
"hard" i2c controller on the Microchip PolarFire SoC & the basic feature
set for "soft" i2c controller implemtations in the FPGA fabric.
Co-developed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Meteor Lake-P.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The recently added support for EFCH MMIO regions introduced a memory
leak in that code path. The leak is caused by the fact that
release_resource() merely removes the resource from the tree but does
not free its memory. We need to call release_mem_region() instead,
which does free the memory. As a nice side effect, this brings back
some symmetry between the legacy and MMIO paths.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Terry Bowman <Terry.Bowman@amd.com>
Fixes: 7c148722d0 ("i2c: piix4: Add EFCH MMIO support to region request and release")
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
Free the adap structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 611e12ea0f ("i2c: core: manage i2c bus device refcount in i2c_[get|put]_adapter")
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
[wsa: added comment to the code, added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
HZ macros has been centralized in units.h since [1]. Use it to avoid
duplicated definition.
[1] commit e2c77032fc ("units: add the HZ macros")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
MSM8974 CCI is the same as MSM8916 except it has two masters.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The clsk are prepared, enabled, then disabled. So if an error occurs after
the disable step, they are still prepared.
Add an error handling path to unprepare the clks in such a case, as already
done in the .remove function.
Fixes: 8b4fc246c3 ("i2c: mediatek: Optimize master_xfer() and avoid circular locking")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-rk3x
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When I attempt to shut down (or reboot) my R8 based NTC CHIP with this
i2c driver I get the following error: "i2c i2c-0: mv64xxx: I2C bus
locked, block: 1, time_left: 0". Reboots are successful but shutdowns
freeze. If I comment out the shutdown routine the device both reboots
and shuts down successfully without receiving this error (however it
does receive a warning of missing atomic_xfer).
It appears that very few i2c drivers have a shutdown method, I assume
because these devices are often used to communicate with PMICs (such
as in my case with the R8 based NTC CHIP). I'm proposing we simply
remove this method so long as it doesn't cause trouble for others
downstream. I'll work on an atomic_xfer method and submit that in
a different patch.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the coverity warning
mixed_enum_type: enumerated type mixed with another type
We are passing an enum in the xiic_wakeup lets change
the function parameters to reflect that.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
[wsa: fixed $subject with proper prefix]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit c62ebb3d5f ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit b33af11de2 ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: c62ebb3d5f ("i2c: designware: Add support for an interface clock")
Fixes: b33af11de2 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback that just returns 0 is equivalent to no callback at all
as can be seen in i2c_device_remove(). So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/i2c/busses/i2c-mxs.c:802:18: warning: cast to smaller integer type 'enum mxs_i2c_devtype' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c32abd8b56 ("i2c: mxs: Remove unneeded platform_device_id")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Trivial non-functional change, which adds an alias to an extensively
used data location.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the one-line comments capital in the driver to get the comment style
consistent.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add NPCM8XX I2C support.
The NPCM8XX uses a similar i2c module as NPCM7XX.
The internal HW FIFO is larger in NPCM8XX.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the slave transaction logic to be compatible with the generic
slave backend driver.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "data->block[0]" variable comes from the user and is a number
between 0-255. It needs to be capped to prevent writing beyond the end
of dma_buffer[].
Fixes: 5e9a97b1f4 ("i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL")
Reported-and-tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I2C has only driver updates for 5.19. Bigger changes are for Meson,
NPCM, and R-Car, but there are also changes all over the place.
-----BEGIN PGP SIGNATURE-----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=vdUW
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Only driver updates for 5.19.
Bigger changes are for Meson, NPCM, and R-Car, but there are also
changes all over the place"
* tag 'i2c-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: meson: fix typo in comment
i2c: rcar: use flags instead of atomic_xfer
i2c: rcar: REP_AFTER_RD is not a persistent flag
i2c: rcar: use BIT macro consistently
i2c: qcom-geni: remove unnecessary conditions
i2c: mt7621: Use devm_platform_get_and_ioremap_resource()
i2c: rcar: refactor handling of first message
i2c: rcar: avoid race condition with SMIs
i2c: xiic: Correct the datatype for rx_watermark
i2c: rcar: fix PM ref counts in probe error paths
i2c: npcm: Handle spurious interrupts
i2c: npcm: Correct register access width
i2c: npcm: Add tx complete counter
i2c: npcm: Fix timeout calculation
i2c: npcm: Remove unused variable clk_regmap
i2c: npcm: Change the way of getting GCR regmap
i2c: xiic: Fix Tx Interrupt path for grouped messages
i2c: xiic: Fix coding style issues
i2c: xiic: return value of xiic_reinit
i2c: cadence: Increase timeout per message if necessary
...
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-rcar already has priv->flags. This patch adds a new persistent flag
ID_P_NOT_ATOMIC and uses it to save the extra variable. The negation of
the logic was done to make the code more readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[wsa: negated the logic, rebased, updated the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Previous refactoring makes it easy now to convert the above flag to a
non-persistent one. This is more appropriate and easier to maintain.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We know that "ret" is a negative error code at this point so there is
no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the missing clk_disable_unprepare() before return
from mtk_i2c_probe() in the error handling case.
Fixes: d04913ec5f ("i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After moving ICMSR handling to interrupt handlers previously to fix a
race condition, we can now also move ICMSR handling for the first
message out of the function to prepare a message. By introducing a
seperate function to initialize the first message, we can not only
remove some code duplication but the remaining code is also easier to
follow. The function to prepare a message is much simpler without ICMSR
handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A customer experienced a race condition with 'repeated starts' when a
System Management Interrupt took over for 30us and more. The problem was
that during the SMI a new MAT interrupt came in because we set up the
'repeated start' condition. But the old one was not acknowledged yet.
So, when it was acknowledged after the SMI, the new MAT interrupt was
lost, confusing the state machine of the driver.
The fix consists of two parts. First, we do not clear the status
register for 'repeated starts' when preparing the next message anymore.
The interrupt handlers for sending and receiving data is now solely
responsible for that and it makes the code easier to follow, in fact.
Secondly, clearing the status register is now split up to handle MAT
interrupts independently. This avoids the race condition because the old
MAT interrupt will be now cleared before we initiate the "repeated
start" condition.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The message length data type should be u16 as per the i2c_msg structure.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have to take care of ID_P_PM_BLOCKED when bailing out during probe.
Fixes: 7ee24eb508 ("i2c: rcar: disable PM in multi-master mode")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On some platforms in rare cases (1 to 100,000 transactions),
the i2c gets a spurious interrupt which means that we enter an interrupt
but in the interrupt handler we don't find any status bit that points to
the reason we got this interrupt.
This may be a case of a rare HW issue or signal integrity issue that is
still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is not
enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the
transaction.
On next xmit transaction if the bus is still busy the master will issue a
recovery process before issuing the new transaction.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always
incorrect, but simply didn't cause a visible error on the 32-bit machine.
On the 64-bit machine, the kernel message reports that ESR value is
0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that
it's the alignment fault.
SMBnCTL3's address is 0xE.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
tx_complete counter is used to indicate successful transaction count.
Similar counters for failed tx were previously added.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use adap.timeout for timeout calculation instead of hard-coded
value of 35ms.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unused variable clk_regmap.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change the way of getting NPCM system manager reigster (GCR)
and still maintain the old mechanism as a fallback if getting
nuvoton,sys-mgr fails while working with the legacy devicetree
file.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a group of messages are sent from user space as a set, if
the last message has less than Tx FIFO DEPTH number of bytes
to transfer, Tx half empty interrupt is triggered continuously
from the hardware. It is due to Bus not busy interrupt coming
along with Tx half empty and tx empty.
Hence, service the Tx interrupts before Bus not busy interrupt
to update the i2c message status correctly.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most of these stuff are reported by checkpatch.
But fixes are:
- Incorrect indetation
- Missing blank line after variable declaration
- Additional ()
- Missing spaces around +
- Missing parenthesis when if has them
- Newlines
- Remove MODULE_ALIAS - none is really using it
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Check the return value of xiic_reinit.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's more logical to read these get timing parameters ACPI method calls
sorted by speed categories in increasing order: Standard-mode,
Fast-mode, Fast-mode Plus and High-speed mode.
Originally these were in order after commit a92ec1746f
("i2c: designware: get fast plus and high speed *CNT configuration") but
got mixed up over the years.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8 ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the missing clk_disable_unprepare() before return
from meson_i2c_probe() in the error handling case.
Fixes: a57f9b4dd6 ("i2c: meson: Use 50% duty cycle for I2C clock")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
powerpc's asm/prom.h brings some headers that it doesn't
need itself.
In order to clean it up, first add missing headers in
users of asm/prom.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The supplied buffer might be on the stack and we get the following error
message:
[ 3.312058] at91_i2c e0070600.i2c: rejecting DMA map of vmalloc memory
Use i2c_{get,put}_dma_safe_msg_buf() to get a DMA-able memory region if
necessary.
Fixes: 60937b2cdb ("i2c: at91: add dma support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Especially (but not only) during probe, it may happen that multiple
devices are communicating via i2c (or multiple i2c busses) and
sometimes while others are probing asynchronously.
For example, a Cr50 TPM may be filling entropy (or userspace may be
reading random data) while the rt5682 (i2c) codec driver reads/sets
some registers, like while getting/setting a clock's rate, which
happens both during probe and during system operation.
In this driver, the mtk_i2c_transfer() function (which is the i2c
.master_xfer() callback) was granularly managing the clocks by
performing a clk_bulk_prepare_enable() to start them and its inverse.
This is not only creating possible circular locking dependencies in
the some cases (like former explanation), but it's also suboptimal,
as clk_core prepare/unprepare operations are using mutex locking,
which creates a bit of unwanted overhead (for example, i2c trackpads
will call master_xfer() every few milliseconds!).
With this commit, we avoid both the circular locking and additional
overhead by changing how we handle the clocks in this driver:
- Prepare the clocks during probe (and PM resume)
- Enable/disable clocks in mtk_i2c_transfer()
- Unprepare the clocks only for driver removal (and PM suspend)
For the sake of providing a full explanation: during probe, the
clocks are not only prepared but also enabled, as this is needed
for some hardware initialization but, after that, we are disabling
but not unpreparing them, leaving an expected state for the
aforementioned clock handling strategy.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Adjust retry period and timeout values for x86-PSP mailbox based on the
typical I2C traffic generated by PSP. In order to limit the possibility
of timeouts, x86 should reduce the interval between retries as well as
increase overall time after which it gives up.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The duty cycle of 33% is less than the required
by the I2C specs for the LOW period of the SCL
clock.
Move the duty cyle to 50% for 100Khz or lower
clocks, and (40% High SCL / 60% Low SCL) duty
cycle for clocks above 100Khz.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Differentiate between masks and shifts
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With this feature added, SMBus Block reads and Proc calls are now
supported. This patch is the best of two independent developments by
Wolfram and Bhuvanesh + Andrew, refactored again by Wolfram.
Signed-off-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Sparse has warned us about wrong address space for user pointers:
i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
i2c-dev.c:561:50: expected unsigned char [usertype] *buf
i2c-dev.c:561:50: got void [noderef] __user *
Force cast the pointer to (__u8 *) that is used by I²C core code.
Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.
Fixes: 3265a7e6b4 ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638a ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- tracepoints when Linux acts as an I2C client
- added support for AMD PSP
- whole subsystem now uses generic_handle_irq_safe()
- piix4 driver gained MMIO access enabling so far missed controllers
with AMD chipsets
- a bulk of device driver updates, refactorization, and fixes.
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (61 commits)
i2c: mux: demux-pinctrl: do not deactivate a master that is not active
i2c: meson: Fix wrong speed use from probe
i2c: add tracepoints for I2C slave events
i2c: designware: Remove code duplication
i2c: cros-ec-tunnel: Fix syntax errors in comments
MAINTAINERS: adjust XLP9XX I2C DRIVER after removing the devicetree binding
i2c: designware: Mark dw_i2c_plat_{suspend,resume}() as __maybe_unused
i2c: mediatek: Add i2c compatible for Mediatek MT8168
dt-bindings: i2c: update bindings for MT8168 SoC
i2c: mt65xx: Simplify with clk-bulk
i2c: i801: Drop two outdated comments
i2c: xiic: Make bus names unique
i2c: i801: Add support for the Process Call command
i2c: i801: Drop useless masking in i801_access
i2c: tegra: Add SMBus block read function
i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers
i2c: designware: Lock the adapter while setting the suspended flag
i2c: mediatek: remove redundant null check
i2c: mediatek: modify bus speed calculation formula
i2c: designware: Fix improper usage of readl
...
power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc. small improvements and fixes
-----BEGIN PGP SIGNATURE-----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=OiYc
-----END PGP SIGNATURE-----
Merge tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Simplify code by moving common part to one function.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Delete the redundant word 'to'
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
[wsa: fixed prefix in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When CONFIG_PM is set but CONFIG_PM_SLEEP is not, two compiler warnings
appear:
drivers/i2c/busses/i2c-designware-platdrv.c:444:12: error: unused function 'dw_i2c_plat_suspend' [-Werror,-Wunused-function]
static int dw_i2c_plat_suspend(struct device *dev)
^
drivers/i2c/busses/i2c-designware-platdrv.c:465:12: error: unused function 'dw_i2c_plat_resume' [-Werror,-Wunused-function]
static int dw_i2c_plat_resume(struct device *dev)
^
2 errors generated.
These functions are only used in SET_LATE_SYSTEM_SLEEP_PM_OPS(), which
is defined as empty when CONFIG_PM_SLEEP is not defined. Mark the
functions as __maybe_unused to make it clear that these functions might
be unused in this configuration.
Fixes: c57813b8b2 ("i2c: designware: Lock the adapter while setting the suspended flag")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8168. Compare to MT2712 i2c controller,
MT8168 need to synchronize signal with dma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since depending on the SoC or specific bus functionality some clocks
may be optional, we cannot get the benefit of using devm_clk_bulk_get()
but, by migrating to clk-bulk, we are able to remove the custom functions
mtk_i2c_clock_enable() and mtk_i2c_clock_disable(), increasing common
APIs usage, hence (lightly) decreasing kernel footprint.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
* Timeouts are reported even in interrupt mode since commit
b3b8df9772 ("i2c: i801: Use wait_event_timeout to wait for
interrupts") so drop the comment which claims this only happens in
polled mode.
* xact does not include the PEC bit, as the driver does not support
software PEC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Chris Pringle