Follow the advice of the below link and prefer 'strscpy'. Conversion is
easy because no driver used the return value and has been done with a
simple sed invocation.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8188 and added mt_i2c_regs_v3[], since
MT8188 i2c OFFSET_SLAVE_ADDR register changed from 0x04 to 0x94.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The clsk are prepared, enabled, then disabled. So if an error occurs after
the disable step, they are still prepared.
Add an error handling path to unprepare the clks in such a case, as already
done in the .remove function.
Fixes: 8b4fc246c3 ("i2c: mediatek: Optimize master_xfer() and avoid circular locking")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Especially (but not only) during probe, it may happen that multiple
devices are communicating via i2c (or multiple i2c busses) and
sometimes while others are probing asynchronously.
For example, a Cr50 TPM may be filling entropy (or userspace may be
reading random data) while the rt5682 (i2c) codec driver reads/sets
some registers, like while getting/setting a clock's rate, which
happens both during probe and during system operation.
In this driver, the mtk_i2c_transfer() function (which is the i2c
.master_xfer() callback) was granularly managing the clocks by
performing a clk_bulk_prepare_enable() to start them and its inverse.
This is not only creating possible circular locking dependencies in
the some cases (like former explanation), but it's also suboptimal,
as clk_core prepare/unprepare operations are using mutex locking,
which creates a bit of unwanted overhead (for example, i2c trackpads
will call master_xfer() every few milliseconds!).
With this commit, we avoid both the circular locking and additional
overhead by changing how we handle the clocks in this driver:
- Prepare the clocks during probe (and PM resume)
- Enable/disable clocks in mtk_i2c_transfer()
- Unprepare the clocks only for driver removal (and PM suspend)
For the sake of providing a full explanation: during probe, the
clocks are not only prepared but also enabled, as this is needed
for some hardware initialization but, after that, we are disabling
but not unpreparing them, leaving an expected state for the
aforementioned clock handling strategy.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8168. Compare to MT2712 i2c controller,
MT8168 need to synchronize signal with dma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since depending on the SoC or specific bus functionality some clocks
may be optional, we cannot get the benefit of using devm_clk_bulk_get()
but, by migrating to clk-bulk, we are able to remove the custom functions
mtk_i2c_clock_enable() and mtk_i2c_clock_disable(), increasing common
APIs usage, hence (lightly) decreasing kernel footprint.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Because clk_disable_unprepare already checked NULL clock parameter,
so the additional checks are unnecessary, just remove it
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When clock-div is 0 or greater than 1, the bus speed
calculated by the old speed calculation formula will be
larger than the target speed. So we update the formula.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8186. Compare to MT8192 i2c controller,
MT8186 doesn't need handshake signal witch apdma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a timeout error occurs in i2c transter, it is usually related
to the i2c/dma IP hardware configuration. Therefore, the purpose of
this patch is to dump the key register values of i2c/dma when a
timeout occurs in i2c for debugging.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the commit be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39 ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- core supports now bus regulators controlling power for SCL/SDA
- quite some DT binding conversions to YAML
- added a seperate DT binding for the optional SMBus Alert feature
- documentation with examples how to deal with I2C sysfs files
- some bigger rework for the i801 driver
- and a few usual driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (42 commits)
i2c: ali1535: mention that the device should not be disabled
i2c: mpc: Restore reread of I2C status register
i2c: core-smbus: Expose PEC calculate function for generic use
Documentation: i2c: Add doc for I2C sysfs
i2c: core: Disable client irq on reboot/shutdown
dt-bindings: i2c: update bindings for MT8195 SoC
i2c: imx: Fix some checkpatch warnings
i2c: davinci: Simplify with dev_err_probe()
i2c: cadence: Simplify with dev_err_probe()
i2c: xiic: Simplify with dev_err_probe()
i2c: cadence: Clear HOLD bit before xfer_size register rolls over
dt-bindings: i2c: ce4100: Replace "ti,pcf8575" by "nxp,pcf8575"
i2c: i801: Improve i801_setup_hstcfg
i2c: i801: Use driver name constant instead of function dev_driver_string
i2c: i801: Simplify initialization of i2c_board_info in i801_probe_optional_slaves
i2c: i801: Improve status polling
i2c: cht-wc: Replace of_node by NULL
i2c: riic: Add RZ/G2L support
dt-bindings: i2c: renesas,riic: Document RZ/G2L I2C controller
dt-bindings: i2c: renesas,iic: Convert to json-schema
...
Add vbus-supply which provides power to SCL/SDA. Pass this regulator
into core so it can be turned on/off for low power mode support.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c controller driver do dma reset after transfer timeout,
but sometimes dma reset will trigger an unexpected DMA_ERR irq.
It will cause the i2c controller to continuously send interrupts
to the system and cause soft lock-up. So we need to disable i2c
start_en and clear intr_stat to stop i2c controller before dma
reset when transfer timeout.
Fixes: aafced673c06("i2c: mediatek: move dma reset before i2c reset")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rename i2c irq name with dev_name() which can provide unique
naming in /proc/interrupts for each instance of the I2C IP core.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The parameters of tSU,STA/tHD,STA/tSU,STOP maybe out of spec due
to device clock-stretch or circuit loss, we could get a suitable
scl_int_delay_ns from i2c_timings to compensate these parameters
to meet the spec via EXT_CONF register.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The right flag is apdma_sync when apdma remove hand-shake signel.
Fixes: 05f6f7271a ("i2c: mediatek: Fix apdma and i2c hand-shake timeout")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There are some omissions in the previous patch about replacing
I2C_MAX_FAST_MODE__FREQ with I2C_MAX_FAST_MODE_PLUS_FREQ and
need to fix it.
Fixes: b44658e755b5("i2c: mediatek: Send i2c master code at more than 1MHz")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some i2c device driver indirectly uses I2C driver when it is now
being suspended. The i2c devices driver is suspended during the
NOIRQ phase and this cannot be changed due to other dependencies.
Therefore, we also need to move the suspend handling for the I2C
controller driver to the NOIRQ phase as well.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The master code needs to being sent when the speed is more than
I2C_MAX_FAST_MODE_PLUS_FREQ, not I2C_MAX_FAST_MODE_FREQ in the
latest I2C-bus specification and user manual.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The max frequency of mediatek i2c controller driver is
I2C_MAX_HIGH_SPEED_MODE_FREQ, not I2C_MAX_FAST_MODE_PLUS_FREQ.
Fix it.
Fixes: 90224e6468 ("i2c: drivers: Use generic definitions for bus frequencies")
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The struct i2c_spec_values have it's members documented but is
missing the starting '@', which leads to warings like:
drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values'
We also delete min_high_ns member as it is not used in the code.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8192. Compare to MT8183 i2c controller,
MT8192 support more then 8GB DMA mode.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Newer MTK chip support more than 8GB of dram. Replace support_33bits
with more general dma_max_support and remove mtk_i2c_set_4g_mode.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it need to keep i2c and
apdma in sync manually.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds a algorithm to calculate some ac-timing parameters
which can fully meet I2C Spec.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since commit abf4923e97 ("i2c: mediatek: disable zero-length transfers
for mt8183"), there is a NULL pointer dereference for all the SoCs
that don't have any quirk. mtk_i2c_functionality is not checking that
the quirks pointer is not NULL before starting to use it.
This commit add a call to i2c_check_quirks which will check whether
the quirks pointer is set, and if so will check if the IP has the
NO_ZERO_LEN quirk.
Fixes: abf4923e97 ("i2c: mediatek: disable zero-length transfers for mt8183")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Cengiz Can <cengiz@kernel.wtf>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Ulrich Hecht <uli@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Quoting from mt8183 datasheet, the number of transfers to be
transferred in one transaction should be set to bigger than 1,
so we should forbid zero-length transfer and update functionality.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
[wsa: shortened commit message a little]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i2c compatible for MT8183. Compare to MT2712 i2c controller,
MT8183 has different register offsets. Ltiming_reg is added to
adjust low width of SCL. Arb clock and dma_sync are needed.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When i2c and apdma use different source clocks, we should enable
synchronization between them.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When two i2c controllers are internally connected to the same
GPIO pins, the arb clock is needed to ensure that the waveforms
do not interfere with each other. And we also need to enable
the interrupt to find arb lost, old i2c controllers also have
the bit.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
New i2c registers would have different offsets, so we use different
offsets array to distinguish different i2c registers version.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA with zero-length transfers doesn't make sense and this HW doesn't
support them at all, so increase the threshold.
Fixes: fc66b39fe3 ("i2c: mediatek: Use DMA safe buffers for i2c transactions")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Completion_done() is useless when we don't use its return value,
so we remove it.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Different speeds have been defined by macros,
so we use macros definitions.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA mode will always be used in i2c transactions, try to allocate
a DMA safe buffer if the buf of struct i2c_msg used is not DMA safe.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_i2c_probe() is to match an entry in
mtk_i2c_of_match[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure i2c module clock has been enabled before i2c registers
access.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT2712. Compare to MT8173 i2c controller,
internal divider of i2c source clock need to be configured for
MT2712 i2c speed calculation.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The speed of sending i2c master code in high-speed mode depends on
source clock, clock-div and TIMING register. The source clock and
clock-div of different SoC are not all the same. In order to send
i2c master code at 400k in high-speed mode, a appropriate value
should be set to TIMING register for a certain source clock and
clock-div.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All length fields in Linux I2C are u16, so a HW length limitation of 16
bit lengths is not a limitation. Remove the quirk structure.
Tested-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang