Merge additional APEI changes, ACPI updates related to device wakeup and
system restart and ACPI thermal driver cleanups for 6.1-rc1:
- Fix a memory leak in APEI by avoiding to add do not add task_work to
kernel threads running when an asynchronous error is detected (Shuai
Xue).
- Add ACPI support for handling system wakeups via GPIO wake capable
IRQs in addition to GPEs (Raul E Rangel).
- Make the system reboot code put ACPI-enabled systems into the S5
(system off) state which is necessary for some platforms to work as
expected (Kai-Heng Feng).
- Make the white space usage in the ACPI thermal driver more consistent
and drop redundant code from it (Rafael Wysocki).
* acpi-apei:
ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
* acpi-wakeup:
ACPI: PM: Take wake IRQ into consideration when entering suspend-to-idle
i2c: acpi: Use ACPI wake capability bit to set wake_irq
ACPI: resources: Add wake_capable parameter to acpi_dev_irq_flags
gpiolib: acpi: Add wake_capable variants of acpi_dev_gpio_irq_get
* acpi-reboot:
PM: ACPI: reboot: Reinstate S5 for reboot
kernel/reboot: Add SYS_OFF_MODE_RESTART_PREPARE mode
* acpi-thermal:
ACPI: thermal: Drop some redundant code
ACPI: thermal: Drop redundant parens from expressions
ACPI: thermal: Use white space more consistently
This change adds support for ACPI devices that use ExclusiveAndWake or
SharedAndWake in their _CRS GpioInt definition (instead of using _PRW),
and also provide power resources. Previously the ACPI subsystem had no
idea if the device had a wake capable interrupt armed. This resulted
in the ACPI device PM system placing the device into D3Cold, and thus
cutting power to the device. With this change we will now query the
_S0W method to figure out the appropriate wake capable D-state.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge ACPI resource management and ACPI power management chages for
6.1-rc1:
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus).
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw).
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus).
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello).
* acpi-resource:
ACPI: resource: Add ASUS model S5402ZA to quirks
usb: typec: intel_pmc_mux: Use the helper acpi_dev_get_memory_resources()
ACPI: resource: Skip IRQ override on Asus Vivobook K3402ZA/K3502ZA
ACPI: LPSS: Use the helper acpi_dev_get_memory_resources()
ACPI: APD: Use the helper acpi_dev_get_memory_resources()
ACPI: resource: Add helper function acpi_dev_get_memory_resources()
ACPI: resource: Filter out the non memory resources in is_memory()
* acpi-pm:
ACPI: x86: s2idle: Add another ID to s2idle_dmi_table
ACPI: x86: s2idle: Fix a NULL pointer dereference
ACPI: x86: s2idle: Add a quirk for ASUSTeK COMPUTER INC. ROG Flow X13
ACPI: x86: s2idle: Add a quirk for Lenovo Slim 7 Pro 14ARH7
ACPI: x86: s2idle: Add a quirk for ASUS ROG Zephyrus G14
ACPI: x86: s2idle: Add a quirk for ASUS TUF Gaming A17 FA707RE
ACPI: x86: s2idle: Add module parameter to prefer Microsoft GUID
ACPI: x86: s2idle: If a new AMD _HID is missing assume Rembrandt
ACPI: x86: s2idle: Move _HID handling for AMD systems into structures
ACPI: PM: Fix acpi_dev_state_d0() kerneldoc
In principle, it should be valid to pass NULL as the ACPI device
pointer to acpi_device_get_power() and acpi_device_set_power() and they
both are expected to return -EINVAL in that case, but that has been
broken recently by commit 62fcb99bdf ("ACPI: Drop parent field from
struct acpi_device") which has caused the ACPI device pointer to be
dereferenced in these functions before the NULL check.
Fix that and while at it make acpi_device_set_power() only use the
parent field if the target ACPI device object's ignore_parent flag
in not set.
Fixes: 62fcb99bdf ("ACPI: Drop parent field from struct acpi_device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The parent field in struct acpi_device is, in fact, redundant,
because the dev.parent field in it effectively points to the same
object and it is used by the driver core.
Accordingly, the parent field can be dropped from struct acpi_device
and for this purpose define acpi_dev_parent() to retrieve a parent
struct acpi_device pointer from the dev.parent field in struct
acpi_device. Next, update all of the users of the parent field
in struct acpi_device to use acpi_dev_parent() instead of it and
drop it.
While at it, drop the ACPI_IS_ROOT_DEVICE() macro that is only used
in one place in a confusing way.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
The documentation for acpi_dev_state_d0() referred to
Documentation/firmware-guide/acpi/low-power-probe.rst that does not exist,
the right file name is Documentation/firmware-guide/acpi/non-d0-probe.rst.
Fix this.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because acpi_bus_get_acpi_device() is completely analogous to
acpi_fetch_acpi_dev(), rename it to acpi_get_acpi_dev() and
add a kerneldoc comment to it.
Accordingly, rename acpi_bus_put_acpi_device() to acpi_put_acpi_dev()
and update all of the users of these two functions.
While at it, move the acpi_fetch_acpi_dev() header next to the
acpi_get_acpi_dev() header in the header file holding them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
Introduce acpi_device_fix_up_power_extended() for fixing up power of
a device having an ACPI companion in a manner that takes the device's
children into account and make the MMC code use it in two places
instead of walking the list of the device ACPI companion's children
directly.
This will help to eliminate the children list head from struct
acpi_device as it is redundant and it is used in questionable ways
in some places (in particular, locking is needed for walking the
list pointed to it safely, but it is often missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge power management, PCI and sysfs-related material and changes
related to handling ACPI tables for 5.19-rc1:
- Improve debug messages in the ACPI device PM code (Rafael Wysocki).
- Block ASUS B1400CEAE from suspend to idle by default (Mario
Limonciello).
- Improve handling of PCI devices that are in D3cold during system
initialization (Rafael Wysocki).
- Fix BERT error region memory mapping (Lorenzo Pieralisi).
- Add support for NVIDIA 16550-compatible port subtype to the SPCR
parsing code (Jeff Brasen).
- Use static for BGRT_SHOW kobj_attribute defines (Tom Rix).
- Fix missing prototype warning for acpi_agdi_init() (Ilkka Koskinen).
* acpi-pm:
ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
ACPI: PM: Always print final debug message in acpi_device_set_power()
ACPI: PM: Unify debug messages in acpi_device_set_power()
ACPI: PM: Change pr_fmt() in device_pm.c
ACPI: PM: Convert debug message in acpi_device_get_power()
* acpi-pci:
ACPI: bus: Avoid non-ACPI device objects in walks over children
PCI: ACPI: PM: Power up devices in D3cold before scanning them
ACPI: PM: Introduce acpi_dev_power_up_children_with_adr()
ACPI: bus: Introduce acpi_dev_for_each_child()
* acpi-sysfs:
ACPI: sysfs: Fix BERT error region memory mapping
* acpi-tables:
ACPI: AGDI: Fix missing prototype warning for acpi_agdi_init()
ACPI: BGRT: use static for BGRT_SHOW kobj_attribute defines
ACPI: SPCR: Add support for NVIDIA 16550-compatible port subtype
When walking the children of an ACPI device, take extra care to avoid
using to_acpi_device() on the ones that are not ACPI devices, because
that may lead to out-of-bounds access and memory corruption.
While at it, make the function passed to acpi_dev_for_each_child()
take a struct acpi_device pointer argument (instead of a struct device
one), so it is more straightforward to use.
Fixes: b7dd6298db ("ACPI: PM: Introduce acpi_dev_power_up_children_with_adr()")
Reported-by: kernel test robot <oliver.sang@intel.com>
BugLink: https://lore.kernel.org/lkml/20220420064725.GB16310@xsang-OptiPlex-9020/
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
acpi_device_set_power() prints debug messages regarding its outcome
(whether or not the power state has been changed and how) in all
cases except when the device whose power state is being changed to D0
is in that power state already.
Make acpi_device_set_power() print a final debug message in that case
too and while at it, fix the indentation of the "end" label in this
function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a function powering up all of the children of a given ACPI
device object that are power-manageable and hold valid _ADR ACPI
objects so as to make it possible to prepare the corresponding
"physical" devices for enumeration carried out by a bus type driver,
like PCI.
This function will be used in a subsequent change set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert all of the debug messages printed by acpi_device_set_power()
to acpi_handle_debug() and adjust them slightly for consistency with
acpi_device_get_power() and other acpi_device_set_power() debug
messages.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All messages printed by functions in this file either contain
the "ACPI" or "acpi" string regardless of the format, or they don't
need to contain it at all.
In the former case, the "ACPI:" string added by the format is
redundant, so drop it from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert the debug message printed by acpi_device_get_power() to
acpi_handle_debug(), because that function is also called when
the ACPI device object name has not been set yet and the dev_dbg()
message printed by it at that time is not useful.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the ACPI code to use acpi_fetch_acpi_dev() instead of
acpi_bus_get_device() where applicable.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Add a convenience function to tell whether a device is in D0 state,
primarily for use in drivers' probe or remove functions on busses where
the custom is to power on the device for the duration of both.
Returns false on non-ACPI systems.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----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=D6dS
-----END PGP SIGNATURE-----
Merge tag 'for-5.14/drivers-2021-06-29' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Pretty calm round, mostly just NVMe and a bit of MD:
- NVMe updates (via Christoph)
- improve the APST configuration algorithm (Alexey Bogoslavsky)
- look for StorageD3Enable on companion ACPI device
(Mario Limonciello)
- allow selecting the network interface for TCP connections
(Martin Belanger)
- misc cleanups (Amit Engel, Chaitanya Kulkarni, Colin Ian King,
Christoph)
- move the ACPI StorageD3 code to drivers/acpi/ and add quirks
for certain AMD CPUs (Mario Limonciello)
- zoned device support for nvmet (Chaitanya Kulkarni)
- fix the rules for changing the serial number in nvmet
(Noam Gottlieb)
- various small fixes and cleanups (Dan Carpenter, JK Kim,
Chaitanya Kulkarni, Hannes Reinecke, Wesley Sheng, Geert
Uytterhoeven, Daniel Wagner)
- MD updates (Via Song)
- iostats rewrite (Guoqing Jiang)
- raid5 lock contention optimization (Gal Ofri)
- Fall through warning fix (Gustavo)
- Misc fixes (Gustavo, Jiapeng)"
* tag 'for-5.14/drivers-2021-06-29' of git://git.kernel.dk/linux-block: (78 commits)
nvmet: use NVMET_MAX_NAMESPACES to set nn value
loop: Fix missing discard support when using LOOP_CONFIGURE
nvme.h: add missing nvme_lba_range_type endianness annotations
nvme: remove zeroout memset call for struct
nvme-pci: remove zeroout memset call for struct
nvmet: remove zeroout memset call for struct
nvmet: add ZBD over ZNS backend support
nvmet: add Command Set Identifier support
nvmet: add nvmet_req_bio put helper for backends
nvmet: add req cns error complete helper
block: export blk_next_bio()
nvmet: remove local variable
nvmet: use nvme status value directly
nvmet: use u32 type for the local variable nsid
nvmet: use u32 for nvmet_subsys max_nsid
nvmet: use req->cmd directly in file-ns fast path
nvmet: use req->cmd directly in bdev-ns fast path
nvmet: make ver stable once connection established
nvmet: allow mn change if subsys not discovered
nvmet: make sn stable once connection was established
...
Currently ACPI power domain brings devices into D0 state in the "resume
early" phase. Normally this does not cause any issues, as powering up
happens quickly. However there are peripherals that have certain timing
requirements for powering on, for example some models of Elan
touchscreens need 300msec after powering up/releasing reset line before
they can accept commands from the host. Such devices will dominate
the time spent in early resume phase and cause increase in overall
resume time as we wait for early resume to complete before we can
proceed to the normal resume stage.
There are ways for a driver to indicate that it can tolerate device
being in the low power mode and that it knows how to power the device
back up when resuming, bit that requires changes to individual drivers
that may not really care about details of ACPI controlled power
management.
This change attempts to solve this issue at ACPI power domain level, by
postponing powering up device until we get to the normal resume stage,
unless there is early resume handler defined for the device, or device
does not declare any resume handlers, in which case we continue powering
up such devices early. This allows us to shave off several hundred
milliseconds of resume time on affected systems.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
AMD systems from Renoir and Lucienne require that the NVME controller
is put into D3 over a Modern Standby / suspend-to-idle
cycle. This is "typically" accomplished using the `StorageD3Enable`
property in the _DSD, but this property was introduced after many
of these systems launched and most OEM systems don't have it in
their BIOS.
On AMD Renoir without these drives going into D3 over suspend-to-idle
the resume will fail with the NVME controller being reset and a trace
like this in the kernel logs:
```
[ 83.556118] nvme nvme0: I/O 161 QID 2 timeout, aborting
[ 83.556178] nvme nvme0: I/O 162 QID 2 timeout, aborting
[ 83.556187] nvme nvme0: I/O 163 QID 2 timeout, aborting
[ 83.556196] nvme nvme0: I/O 164 QID 2 timeout, aborting
[ 95.332114] nvme nvme0: I/O 25 QID 0 timeout, reset controller
[ 95.332843] nvme nvme0: Abort status: 0x371
[ 95.332852] nvme nvme0: Abort status: 0x371
[ 95.332856] nvme nvme0: Abort status: 0x371
[ 95.332859] nvme nvme0: Abort status: 0x371
[ 95.332909] PM: dpm_run_callback(): pci_pm_resume+0x0/0xe0 returns -16
[ 95.332936] nvme 0000:03:00.0: PM: failed to resume async: error -16
```
The Microsoft documentation for StorageD3Enable mentioned that Windows has
a hardcoded allowlist for D3 support, which was used for these platforms.
Introduce quirks to hardcode them for Linux as well.
As this property is now "standardized", OEM systems using AMD Cezanne and
newer APU's have adopted this property, and quirks like this should not be
necessary.
CC: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Prike Liang <prike.liang@amd.com>
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Although first implemented for NVME, this check may be usable by
other drivers as well. Microsoft's specification explicitly mentions
that is may be usable by SATA and AHCI devices. Google also indicates
that they have used this with SDHCI in a downstream kernel tree that
a user can plug a storage device into.
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Suggested-by: Keith Busch <kbusch@kernel.org>
CC: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Prike Liang <prike.liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The ACPI fan device IDs are shared between the fan driver and the
device power management code. The former is modular, so it needs
to include the table of device IDs for module autoloading and the
latter needs that list to avoid attaching the generic ACPI PM domain
to fan devices (which doesn't make sense) possibly before the fan
driver module is loaded.
Unfortunately, that requires the list of fan device IDs to be
updated in two places which is prone to mistakes, so put it into
a symbol definition in a separate header file so there is only one
copy of it in case it needs to be updated again in the future.
Fixes: b9ea0bae26 ("ACPI: PM: Avoid attaching ACPI PM domain to certain devices")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new unique fan ACPI device ID for Alder Lake to
support it in acpi_dev_pm_attach() function.
Fixes: 38748bcb94 ("ACPI: DPTF: Support Alder Lake")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a missed blank line after declarations, reported by checkpatch.pl.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace the remaining ACPI_DEBUG_PRINT() instances in device_pm.c
with dev_dbg() invocations, drop the _COMPONENT and ACPI_MODULE_NAME()
definitions that are not used any more, and drop the no longer needed
ACPI_POWER_COMPONENT definition from the headers and documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When wakeup signaling is enabled for a bridge for the second (or every
next) time in a row, its existing device wakeup power configuration
may not match the new conditions. For example, some devices below
it may have been put into low-power states and that changes the
device wakeup power conditions or similar. This causes functional
problems to appear on some systems (for example, because of it the
Thunderbolt port on Dell Precision 5550 cannot detect devices plugged
in after it has been suspended).
For this reason, modify __acpi_device_wakeup_enable() to refresh the
device wakeup power configuration of the target device on every
invocation, not just when it is called for that device first time
in a row.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to
be reference counted for wakeup enabling, because they may be enabled
to signal wakeup on behalf of their subordinate devices and that
may happen for multiple times in a row, whereas for the other devices
it only makes sense to enable wakeup signaling once.
However, this becomes problematic if the bridge itself is suspended,
because it is treated as a "regular" device in that case and the
reference counting doesn't work.
For instance, suppose that there are two devices below a bridge and
they both can signal wakeup. Every time one of them is suspended,
wakeup signaling is enabled for the bridge, so when they both have
been suspended, the bridge's wakeup reference counter value is 2.
Say that the bridge is suspended subsequently and acpi_pci_wakeup()
is called for it. Because the bridge can signal wakeup, that
function will invoke acpi_pm_set_device_wakeup() to configure it
and __acpi_pm_set_device_wakeup() will be called with the last
argument equal to 1. This causes __acpi_device_wakeup_enable()
invoked by it to omit the reference counting, because the reference
counter of the target device (the bridge) is 2 at that time.
Now say that the bridge resumes and one of the device below it
resumes too, so the bridge's reference counter becomes 0 and
wakeup signaling is disabled for it, but there is still the other
suspended device which may need the bridge to signal wakeup on its
behalf and that is not going to work.
To address this scenario, use wakeup enable reference counting for
all devices, not just for bridges, so drop the last argument from
__acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(),
which causes acpi_pm_set_device_wakeup() and
acpi_pm_set_bridge_wakeup() to become identical, so drop the latter
and use the former instead of it everywhere.
Fixes: 1ba51a7c14 ("ACPI / PCI / PM: Rework acpi_pci_propagate_wakeup()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
* pm-cpufreq:
cpufreq: CPPC: add SW BOOST support
cpufreq: change '.set_boost' to act on one policy
cpufreq: tegra186: add CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
* pm-acpi:
ACPI: PM: Avoid using power resources if there are none for D0
As recently reported, some platforms provide a list of power
resources for device power state D3hot, through the _PR3 object,
but they do not provide a list of power resources for device power
state D0.
Among other things, this causes acpi_device_get_power() to return
D3hot as the current state of the device in question if all of the
D3hot power resources are "on", because it sees the power_resources
flag set and calls acpi_power_get_inferred_state() which finds that
D3hot is the shallowest power state with all of the associated power
resources turned "on", so that's what it returns. Moreover, that
value takes precedence over the acpi_dev_pm_explicit_get() return
value, because it means a deeper power state. The device may very
well be in D0 physically at that point, however.
Moreover, the presence of _PR3 without _PR0 for a given device
means that only one D3-level power state can be supported by it.
Namely, because there are no power resources to turn "off" when
transitioning the device from D0 into D3cold (which should be
supported since _PR3 is present), the evaluation of _PS3 should
be sufficient to put it straight into D3cold, but this means that
the effect of turning "on" the _PR3 power resources is unclear,
so it is better to avoid doing that altogether. Consequently,
there is no practical way do distinguish D3cold from D3hot for
the device in question and the power states of it can be labeled
so that D3hot is the deepest supported one (and Linux assumes
that putting a device into D3hot via ACPI may cause power to be
removed from it anyway, for legacy reasons).
To work around the problem described above modify the ACPI
enumeration of devices so that power resources are only used
for device power management if the list of D0 power resources
is not empty and make it mart D3cold as supported only if that
is the case and the D3hot list of power resources is not empty
too.
Fixes: ef85bdbec4 ("ACPI / scan: Consolidate extraction of power resources lists")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205057
Link: https://lore.kernel.org/linux-acpi/20200603194659.185757-1-hdegoede@redhat.com/
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: youling257@gmail.com
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Transitioned power state logged at the end of setting ACPI power.
However, D3cold won't be in the message because state can only be
D3hot at most.
Use target_state to corretly report when power state is D3cold.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because all callers of dev_pm_smart_suspend_and_suspended use it only
for checking whether or not to skip driver suspend callbacks for a
device, rename it to dev_pm_skip_suspend() in analogy with
dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The name of dev_pm_may_skip_resume() may be easily confused with the
power.may_skip_resume flag which is not checked by that function, so
rename the former as dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Because the power.may_skip_resume device status bit is taken
into account in combination with the DPM_FLAG_LEAVE_SUSPENDED
driver flag, it can be set to 'true' for all devices in the
"suspend" phase of a suspend-resume cycle, so do that.
Then, neither the PM core nor the middle-layer (sybsystem) code
handling it needs to set it to 'true' any more and it just has
to be cleared if there is a reason to avoid skipping the "noirq"
and "early" resume callbacks provided by the driver, so update
the code in question accordingly.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The current code in device_resume_noirq() causes the entire early
resume and resume phases of device suspend to be skipped for
devices for which the noirq resume phase have been skipped (due
to the LEAVE_SUSPENDED flag being set) on the premise that those
devices should stay in runtime-suspend after system-wide resume.
However, that may not be correct in two situations. First, the
middle layer (subsystem) noirq resume callback may be missing for
a given device, but its early resume callback may be present and it
may need to do something even if it decides to skip the driver
callback. Second, if the device's wakeup settings were adjusted
in the suspend phase without resuming the device (that was in
runtime suspend at that time), they most likely need to be
adjusted again in the resume phase and so the driver callback
in that phase needs to be run.
For the above reason, modify the core to allow the middle layer
->resume_late callback to run even if its ->resume_noirq callback
is missing (and the core has skipped the driver-level callback
in that phase) and to allow all device callbacks to run in the
resume phase. Also make the core set the PM-runtime status of
devices with SMART_SUSPEND set whose resume callbacks are not
skipped to "active" in the "noirq" resume phase and update the
affected subsystems (PCI and ACPI) accordingly.
After this change, middle-layer (subsystem) callbacks will always
be invoked in all phases of system suspend and resume and driver
callbacks will always run in the prepare, suspend, resume, and
complete phases for all devices.
For devices with SMART_SUSPEND set, driver callbacks will be
skipped in the late and noirq phases of system suspend if those
devices remain in runtime suspend in __device_suspend_late().
Driver callbacks will also be skipped for them during the
noirq and early phases of the "thaw" transition related to
hibernation in that case.
Setting LEAVE_SUSPENDED means that the driver allows its callbacks
to be skipped in the noirq and early phases of system resume, but
some additional conditions need to be met for that to happen (among
other things, the power.may_skip_resume flag needs to be set for the
device during system suspend for the driver callbacks to be skipped
during the subsequent resume transition).
For all devices with SMART_SUSPEND set whose driver callbacks are
invoked during system resume, the PM-runtime status will be set to
"active" (by the core).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tiger Lake's new unique ACPI device IDs for DPTF and fan drivers are not
valid as the IDs are missing 'C'. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1047 --> INTC1047
INT1040 --> INTC1040
INT1043 --> INTC1043
INT1044 --> INTC1044
Fixes: 55cfe6a5c5 ("ACPI: DPTF: Add Tiger Lake ACPI device IDs")
Fixes: c248dfe7e0 ("ACPI: fan: Add Tiger Lake ACPI device ID")
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tiger Lake has a new unique ACPI device ID for the ACPI fan that
needs to be added to the fan driver and to the blacklist in
acpi_dev_pm_attach() to support it.
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
[ rjw: Subject & changelog, fold in another patch ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Certain ACPI-enumerated devices represented as platform devices in
Linux, like fans, require special low-level power management handling
implemented by their drivers that is not in agreement with the ACPI
PM domain behavior. That leads to problems with managing ACPI fans
during system-wide suspend and resume.
For this reason, make acpi_dev_pm_attach() skip the affected devices
by adding a list of device IDs to avoid to it and putting the IDs of
the affected devices into that list.
Fixes: e5cc8ef312 (ACPI / PM: Provide ACPI PM callback routines for subsystems)
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-opp:
PM / OPP: Correct Documentation about library location
opp: of: Support multiple suspend OPPs defined in DT
dt-bindings: opp: Support multiple opp-suspend properties
opp: core: add regulators enable and disable
opp: Don't decrement uninitialized list_kref
* pm-qos:
PM: QoS: Get rid of unused flags
* acpi-pm:
ACPI: PM: Print debug messages on device power state changes
* pm-domains:
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
PM / Domains: Align in-parameter names for some genpd functions
* pm-tools:
pm-graph: make setVal unbuffered again for python2 and python3
cpupower: update German translation
tools/power/cpupower: fix 64bit detection when cross-compiling
cpupower: Add missing newline at end of file
pm-graph v5.5
Add an ID and a device pointer to 'struct wakeup_source'. Use them to to
expose wakeup sources statistics in sysfs under
/sys/class/wakeup/wakeup<ID>/*.
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tri Vo <trong@android.com>
Tested-by: Kalesh Singh <kaleshsingh@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an acpi_handle_debug() statement to acpi_device_set_power() to
allow ACPI device power state changes to be tracked.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f850a48a07 ("ACPI: PM: Allow transitions to D0 to occur in
special cases") overlooked the fact that acpi_power_transition() may
change the power.state value for the target device and if that
happens, it may confuse acpi_device_set_power() and cause it to
omit the _PS0 evaluation which on some systems is necessary to
change power states of devices from low-power to D0.
Fix that by saving the current value of power.state for the
target device before passing it to acpi_power_transition() and
using the saved value in a subsequent check.
Fixes: f850a48a07 ("ACPI: PM: Allow transitions to D0 to occur in special cases")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
* acpi-pm:
ACPI: PM: Make acpi_sleep_state_supported() non-static
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
ACPI / sleep: Switch to use acpi_dev_get_first_match_dev()
ACPI / LPIT: Correct LPIT end address for lpit_process()
* pm-pci:
ACPI: PM: Unexport acpi_device_get_power()
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
PCI: Do not poll for PME if the device is in D3cold
PCI: Add missing link delays required by the PCIe spec
PCI: PM: Replace pci_dev_keep_suspended() with two functions
PCI: PM: Avoid resuming devices in D3hot during system suspend
Using acpi_device_get_power() outside of ACPI device initialization
and ACPI sysfs is problematic due to the way in which power resources
are handled by it, so unexport it and add a paragraph explaining the
pitfalls to its kerneldoc comment.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In general, it is not correct to call pm_generic_suspend(),
pm_generic_suspend_late() and pm_generic_suspend_noirq() during the
hibernation's "poweroff" transition, because device drivers may
provide special callbacks to be invoked then and the wrappers in
question cause system suspend callbacks to be run. Unfortunately,
that happens in the ACPI PM domain and ACPI LPSS.
To address this potential issue, introduce "poweroff" callbacks
for the ACPI PM and LPSS that will use pm_generic_poweroff(),
pm_generic_poweroff_late() and pm_generic_poweroff_noirq() as
appropriate.
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
First, after a previous change causing all runtime-suspended devices
in the ACPI PM domain (and ACPI LPSS devices) to be resumed before
creating a snapshot image of memory during hibernation, it is not
necessary to worry about the case in which them might be left in
runtime-suspend any more, so get rid of the code related to that from
ACPI PM domain and ACPI LPSS hibernation callbacks.
Second, it is not correct to use pm_generic_resume_early() and
acpi_subsys_resume_noirq() in hibernation "restore" callbacks (which
currently happens in the ACPI PM domain and ACPI LPSS), so introduce
proper _restore_late and _restore_noirq callbacks for the ACPI PM
domain and ACPI LPSS.
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Both the PCI bus type and the ACPI PM domain avoid resuming
runtime-suspended devices with DPM_FLAG_SMART_SUSPEND set during
hibernation (before creating the snapshot image of system memory),
but that turns out to be a mistake. It leads to functional issues
and adds complexity that's hard to justify.
For this reason, resume all runtime-suspended PCI devices and all
devices in the ACPI PM domains before creating a snapshot image of
system memory during hibernation.
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Link: https://lore.kernel.org/linux-acpi/917d4399-2e22-67b1-9d54-808561f9083f@uwyo.edu/T/#maf065fe6e4974f2a9d79f332ab99dfaba635f64c
Reported-by: Robert R. Howell <RHowell@uwyo.edu>
Tested-by: Robert R. Howell <RHowell@uwyo.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
If a device with ACPI PM is left in D0 during a system-wide
transition to the S3 (suspend-to-RAM) or S4 (hibernation) sleep
state, the actual state of the device need not be D0 during resume
from it, although its power.state value will still reflect D0 (that
is, the power state from before the system-wide transition).
In that case, the acpi_device_set_power() call made to ensure that
the power state of the device will be D0 going forward has no effect,
because the new state (D0) is equal to the one reflected by the
device's power.state value. That does not affect power resources,
which are taken care of by acpi_resume_power_resources() called from
acpi_pm_finish() during resume from system-wide sleep states, but it
still may be necessary to invoke _PS0 for the device on top of that
in order to finalize its transition to D0.
For this reason, modify acpi_device_set_power() to allow transitions
to D0 to occur even if D0 is the current power state of the device
according to its power.state value.
That will not affect power resources, which are assumed to be in
the right configuration already (as reflected by the current values
of their reference counters), but it may cause _PS0 to be evaluated
for the device. However, evaluating _PS0 for a device already in D0
may lead to confusion in general, so invoke _PSC (if present) to
check the device's current power state upfront and only evaluate
_PS0 for it if _PSC has returned a power state different from D0.
[If _PSC is not present or the evaluation of it fails, the power
state of the device is assumed to be D0 at this point.]
Fixes: 20dacb71ad (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rafael J. Wysocki