Make sure we do not actually request the RTC IRQ until the device driver
is fully ready to handle and process any interrupt. This way a spurious
interrupt won't crash the system (which may happen if the bootloader was
poking the RTC right before booting Linux).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc_update_irq() might be called with irqs enabled, if a interrupt
handler was registered without IRQF_DISABLED. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_lock/spin_unlock.
Also update kerneldoc and drivers which do extra work to follow the
current interface spec, as suggestted by David Brownell.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQF_SHARED should not be used with IRQF_DISABLED. There is no in-tree
user of this driver and only out-of-tree user I know uses a dedicated irq
line for this RTC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQF_SHARED should not be used with IRQF_DISABLED. This RTC have a
dedicated irq line to SoC's internal interrupt controller so there is
no reason to use IRQF_SHARED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Epson RX-8025SA/NB RTC chips. It includes support for
alarms, periodic interrupts (1 Hz) and clock precision adjustment.
For clock precision adjustment, the SYSFS file "clock_adjust_ppb" gets
created in "/sys/class/rtc/rtcX/device". It permits to set and get the
clock adjustment in ppb (parts per billion), e.g.:
# echo -183000 > /sys/class/rtc/rtc0/device/clock_adjust_ppb
# cat /sys/class/rtc/rtc0/device/clock_adjust_ppb
-183000
This allows to compensate temperature dependent clock drifts. According
to the RX8025 SA/NB application manual the frequency and temperature
characteristics can be approximated using the following equation:
df = a * (ut - t)**2
df: Frequency deviation in any temperature
a : Coefficient = (-35 +-5) * 10**-9
ut: Ultimate temperature in degree = +25 +-5 degree
t : Any temperature in degree
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add ds3231 variant. For that, the BBSQI bit position was changed from a
simple define into a lookup-array as it differs. This also removes
writing to an unused bit in case of the ds1337.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC driver for ds1742 / ds1743 uses a static nvram attribute. This
patch replaces this static attribute with one nvram attribute for each
ds174x registered.
The nvram size is not the same for all types of ds174x. The nvram size is
accessible as the file size of the nvram attribute in sysfs. With only a
single nvram attribute, this file size will be incorrect if more than one
type of ds174x is present on a system. See the comment in the removed
code below.
This patch have been tested with linux-2.6.28 and linux-2.6.29-rc5/6 on a
custom board with one ds1743.
Signed-off-by: Torsten Ertbjerg Rasmussen <ertbjerg@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the alarm interrupt of TWL4030 RTC to wake up the
system from suspend. You can test this patch with following command.
# echo +10 > /sys/class/rtc/rtc0/wakealarm; echo mem > /sys/power/state;
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the rtc-ep93xx driver to use ioremap'ed addresses.
This removes the dependency on <mach/hardware.h> and properly
reports the memory addresses used by the driver in /proc/iomem.
In addition, ep93xx_rtc_init() is updated to use
platform_driver_probe() instead of platform_driver_register().
Also, the device_create_file() calls are now properly checked for
error conditions. The created sysfs files are also now removed
when the driver is removed.
The version number for the driver has been bumped at the request
of Alessandro Zummo.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With no IRQ available/defined, RTC-CMOS driver prints something like:
rtc0: alarms up to one no, y3k, 114 bytes nvram
^^^^
I guess the following is a bit easier to understand:
rtc0: no alarms, y3k, 114 bytes nvram
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds clock framework support to the rtc-sh driver. With this in
place, platforms can default to leaving the clock disabled rather than
placing it in the always enabled state.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
Compared to the other supported chips, the m41t62 uses a different
register to set the square wave frequency.
Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The v3020 RTC can be connected to GPIOs as well as to memory-like
interface. Add ability to use GPIO bit-bang for v3020 read-write access.
[akpm@linux-foundation.org: fix off-by-one in error path]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify the sh_rtc driver to use set_irq_wake() during suspend
and resume. These functions are used to enable the rtc interrupts
in the interrupt controller so the rtc can be used to wakeup the
system from suspend.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PowerPC has been a long time user of the generic RTC abstraction, so hook up
rtc-generic:
- Create the "rtc-generic" platform device if ppc_md.get_rtc_time is set,
- Kill rtc-ppc, as rtc-generic offers the same functionality in a more
generic way, and supports autoloading through udev.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
m68k has been a long time user of the generic RTC abstraction, so hook up
rtc-generic:
- Create the "rtc-generic" platform device if mach_hwclk is set,
- Add checks for mach_hwclk, in anticipation of RTC chip drivers being moved
to drivers/rtc/.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The rtc-parisc driver is not PA-RISC specific at all, as it uses the existing
(but deprecated) generic RTC infrastructure ([gs]et_rtc_time()).
Rename the driver from rtc-parisc to rtc-generic.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
When using platform_driver_probe(), it's not needed to setup a .probe
function, and .remove should be marked __exit_p(), not __devexit_p().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: dann frazier <dannf@hp.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
new_alarm is unsigned so test before the subtraction.
[akpm@linux-foundation.org: time-wrapping fix]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement retries will reach -1 rather than 0, so the
warning and error-out will not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the EPSON RX8025 RTC. The date/time registers of this
chip are compatible with the DS1307.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the rtc-ds1307 driver to work with SMBus controllers like nforce2
that do not support i2c block transfers.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: BARRE Sebastien <sbarre@sdelcc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This isn't a hotpluggable device, so call platform_driver_probe
directly in parisc_rtc_init
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the return value of rtc_valid_tm() instead of just returning 0.
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parisc_rtc now only includes an rtc_device pointer, so let's
just use the rtc_device type directly.
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC subsystem proides ops locking, no need to implement our own
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- the LEAP_YEAR macro is buggy - it references its arg multiple times.
Fix this by turning it into a C function.
- give it a more approriate name
- Move it to rtc.h so that other .c files can use it, instead of copying it.
Cc: dann frazier <dannf@hp.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: stephane eranian <eranian@googlemail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the only two ioctls so the ioctl() function is also removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Yoichi Yuasa