When cxgb4 is enabled with CONFIG_CHELSIO_T4_DCB set, VI enable command
gets called with DCB enabled. But when we have a back to back setup with
DCB enabled on one side and non-DCB on the Peer side. Firmware doesn't
send any DCB_L2_CFG, and DCB priority is never set for Tx queue.
But driver resets the queue priority and state machine whenever there
is a link down, this patch fixes it by adding a check to reset only if
cxgb4_dcb_enabled() returns true.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for firmware errors in the mailbox command loop and report
them differently rather than simply timing out when the firmware goes
belly up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link goes down, from the interrupt handler DCB priority for the
Tx queues needs to be unset. We issue mbox command to unset the Tx queue
priority with negative timeout. In t4_wr_mbox_meat_timeout() do not sleep
when negative timeout is passed, since it is called from interrupt context.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
An out of bounds read of 2 bytes was discovered in cxgb3 with KASAN.
t3_config_rss() expects both arrays it gets as parameters to have
terminators. setup_rss(), the caller, forgets to add a terminator to
one of the arrays. Thankfully the iteration in t3_config_rss() stops
anyway, but in the last iteration the check for the terminator
is an out of bounds read.
Add the missing terminator to rspq_map[].
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump firmware mailbox commands
and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new /sys/kernel/debug/ support to dump a firmware mailbox command
issued and replies for debugging purpose.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace the trylock by a full spin_lock and remove TX_LOCKED return value.
Followup patch will remove TX_LOCKED from the kernel.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware can send a set of asynchronous replies through FW_PORT_CMD
with DCBX information when that's negotiated with the Link Peer. The old
code always assumed that a FW_PORT_CMD reply was always a Get Port
Information message. This change conditionalizes the code to only handle
the Get Port Information messages and throws a warning if we don't
understand what we've been given.
Also refactor t4_handle_fw_rpl() so that core functionality performed by
t4_handle_get_port_info() for a specified port.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor t4_port_init() so that the core functionality is done by
t4_init_portinfo() for a particular port. Also rename variables to
sensible ones.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decode and log port module error, unknown modules and unsupported
modules.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be race between t4_eth_xmit() and t4_free_sge_resources() while
freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need
to stop the xmit frame path which runs in bottom half context while
unloading the driver using _bh variant of the lock. This is to prevent
the deadlock between xmit and driver unload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in iwlwifi, from Matti Gottlieb.
2) Add missing registration of netfilter arp_tables into initial
namespace, from Florian Westphal.
3) Fix potential NULL deref in DecNET routing code.
4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
Ivanov.
5) Fix dst ref counting in VRF, from David Ahern.
6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.
7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.
8) Ravalidate IPV6 datagram socket cached routes properly, particularly
with UDP, from Martin KaFai Lau.
9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.
10) Fix stats typing in bcmgenet driver, from Eric Dumazet.
11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
from Joe Stringer.
12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.
13) atl2 doesn't actually support scatter-gather, so don't advertise the
feature. From Ben Hucthings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
openvswitch: use flow protocol when recalculating ipv6 checksums
Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
atl2: Disable unimplemented scatter/gather feature
net/mlx4_en: Split SW RX dropped counter per RX ring
net/mlx4_core: Don't allow to VF change global pause settings
net/mlx4_core: Avoid repeated calls to pci enable/disable
net/mlx4_core: Implement pci_resume callback
net: phy: spi_ks8895: Don't leak references to SPI devices
net: ethernet: davinci_emac: Fix platform_data overwrite
net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
qede: Fix single MTU sized packet from firmware GRO flow
qede: Fix setting Skb network header
qede: Fix various memory allocation error flows for fastpath
tcp: Merge tx_flags and tskey in tcp_shifted_skb
tcp: Merge tx_flags and tskey in tcp_collapse_retrans
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
openvswitch: Orphan skbs before IPv6 defrag
Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
VSOCK: Only check error on skb_recv_datagram when skb is NULL
...
VPD
Add pci_set_vpd_size() (Hariprasad Shenai)
cxgb4: Set VPD size so we can read both VPD structures (Hariprasad Shenai)
Freescale i.MX6 host bridge driver
Revert "PCI: imx6: Add support for active-low reset GPIO" (Fabio Estevam)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oW8E
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for two issues:
- The VPD parsing code we added for v4.6 keeps some devices from
crashing, but also keeps cxgb4 from reading non-standard extra VPD
data that is relies on. Hariprasad added a way for the driver to
specify how much VPD is valid.
- The i.MX6 active-low reset GPIO support we added in v4.5 caused
regressions on some boards, so we're reverting that.
VPD:
Add pci_set_vpd_size() (Hariprasad Shenai)
cxgb4: Set VPD size so we can read both VPD structures (Hariprasad Shenai)
Freescale i.MX6 host bridge driver:
Revert "PCI: imx6: Add support for active-low reset GPIO" (Fabio Estevam)"
* tag 'pci-v4.6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
cxgb4: Set VPD size so we can read both VPD structures
PCI: Add pci_set_vpd_size() to set VPD size
Revert "PCI: imx6: Add support for active-low reset GPIO"
Chelsio adapters have two VPD structures stored in the VPD:
- offset 0x000: an abbreviated VPD, and
- offset 0x400: the complete VPD.
After 104daa71b3 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. That size only includes the abbreviated VPD structure, so reads of
the complete VPD at 0x400 fail.
Explicitly set the VPD size with pci_set_vpd_size() so the driver can read
both VPD structures.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b3 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.
One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Message level can be set through ethtool, so deprecate module parameter
which is used to set the same.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more SCSI target updates from Nicholas Bellinger:
"This series contains cxgb4 driver prerequisites for supporting iscsi
segmentation offload (ISO), that will be utilized for a number of
future v4.7 developments in iscsi-target for supporting generic hw
offloads"
* 'for-next-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
cxgb4: update Kconfig and Makefile
cxgb4: add iSCSI DDP page pod manager
cxgb4, iw_cxgb4: move delayed ack macro definitions
cxgb4: move VLAN_NONE macro definition
cxgb4: update struct cxgb4_lld_info definition
cxgb4: add definitions for iSCSI target ULD
cxgb4, cxgb4i: move struct cpl_rx_data_ddp definition
cxgb4, iw_cxgb4, cxgb4i: remove duplicate definitions
cxgb4, iw_cxgb4: move definitions to common header file
cxgb4: large receive offload support
cxgb4: allocate resources for CXGB4_ULD_ISCSIT
cxgb4: add new ULD type CXGB4_ULD_ISCSIT
add files for common page pod manager,
both iSCSI initiator and target ULDs will
use common ppod manager for DDP.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Acked-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Chelsio iSCSI target offload driver
will register with cxgb4 driver as ULD of type
CXGB4_ULD_ISCSIT.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Acked-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Queue Set Configuration code was always reserving room for a
Forwarded interrupt Queue even in the cases where we weren't using it.
Figure out how many Ports and Queue Sets we can support. This depends on
knowing our Virtual Function Resources and may be called a second time
if we fall back from MSI-X to MSI Interrupt Mode. This change fixes that
problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a race condition where a system that has network devices set up
to be automatically configured and we get the first Port Link Status
message from the firmware on the Asynchronous Firmware Event Queue before
we've enabled interrupts. If that happens, we end up losing the interrupt
and never realizing that the links has actually come up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function t4vf_wait_dev_ready() is already called in t4vf_prep_adapter(),
no need to call it again in adap_init0().
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a new function t4vf_fl_pkt_align() and use the same in SGE
initialization code to find out freelist packet alignment
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if
the Host Driver provides more Free List Pointers than the Fetch Burst
Minimum value. So if we set FBMIN to 64 bytes and the Host Driver
supplies 128 bytes of Free List Pointer data, the hardware will issue two
64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte
Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use freelist capacity instead of freelist size while checking, if
freelist needs to be refilled
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The vpd strings are left justified, in a fixed length array, with possible
trailing white space and no NUL. So fix them up before calling kstrto*().
This is a recent regression which causes cxgb3 to fail to load.
Fixes: e72c932 ("cxgb3: Convert simple_strtoul to kstrtox")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai