The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward
define a 32-bits maximum transfer size synthesis parameter
(SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration
(SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32,
the layout of the ctrlr0 register changes, moving the data frame format
field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size
can be up to 32-bits.
To support this new format, introduce the DW SPI capability flag
DW_SPI_CAP_DFS32 to indicate that a controller is configured with
SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis
parameter not accessible through a register, the detection of this
parameter value is done in spi_hw_init() by writing and reading the
ctrlr0 register and testing the value of bits [3..0]. These bits are
ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection.
If a DFS32 capable SPI controller is detected, the new field dfs_offset
in struct dw_spi is set to SPI_DFS32_OFFSET (16).
dw_spi_update_config() is modified to set the data frame size field at
the correct position is the CTRLR0 register, as indicated by the
dfs_offset field of the dw_spi structure.
The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave
controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI
capability flag set. However, for these ssi controllers, the dfs_offset
field is set to 0 as before (as per specifications).
Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag
set, dw_spi_add_host() extends the value of bits_per_word_mask from
16-bits to 32-bits. dw_reader() and dw_writer() are also modified to
handle 32-bits iTX/RX FIFO words.
Suggested-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some circumstances the current implementation of the SPI memory
operations may occasionally fail even though they are executed in the
atomic context. This may happen if the system bus is relatively slow in
comparison to the SPI bus frequency, or there is a concurrent access to
it, which makes the MMIO-operations occasionally stalling before
push-pulling data from the DW APB SPI FIFOs. These two problems we've
discovered on the Baikal-T1 SoC. In order to fix them we have no choice
but to set an artificial limitation on the SPI bus speed.
Note currently this limitation will be only applicable for the memory
operations, since the standard SPI core interface is implemented with an
assumption that there is no problem with the automatic CS toggling.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from the synchronous Tx-Rx mode, which has been utilized to create
the normal SPI transfers in the framework of the DW SSI driver, DW SPI
controller supports Tx-only and EEPROM-read modes. The former one just
enables the controller to transmit all the data from the Tx FIFO ignoring
anything retrieved from the MISO lane. The later mode is so called
write-then-read operation: DW SPI controller first pushes out all the data
from the Tx FIFO, after that it'll automatically receive as much data as
has been specified by means of the CTRLR1 register. Both of those modes
can be used to implement the memory operations supported by the SPI-memory
subsystem.
The memory operation implementation is pretty much straightforward, except
a few peculiarities we have had to take into account to make things
working. Since DW SPI controller doesn't provide a way to directly set and
clear the native CS lane level, but instead automatically de-asserts it
when a transfer going on, we have to make sure the Tx FIFO isn't empty
during entire Tx procedure. In addition we also need to read data from the
Rx FIFO as fast as possible to prevent it' overflow with automatically
fetched incoming traffic. The denoted peculiarities get to cause even more
problems if DW SSI controller is equipped with relatively small FIFO and
is connected to a relatively slow system bus (APB) (with respect to the
SPI bus speed). In order to workaround the problems for as much as it's
possible, the memory operation execution procedure collects all the Tx
data into a single buffer and disables the local IRQs to speed the
write-then-optionally-read method up.
Note the provided memory operations are utilized by default only if
a glue driver hasn't provided a custom version of ones and this is not
a DW APB SSI controller with fixed automatic CS toggle functionality.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The DW SSI errors handling method can be generically implemented for all
types of the transfers: IRQ, DMA and poll-based ones. It will be a
function which checks the overflow/underflow error flags and resets the
controller if any of them is set. In the framework of this commit we make
use of the new method to detect the errors in the IRQ- and DMA-based SPI
transfer execution procedures.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The parameter will be needed for another wait-done method being added in
the framework of the SPI memory operation modification in a further
commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI memory operations implementation will require to have the CS register
cleared before executing the operation in order not to have the
transmission automatically started prior the Tx FIFO is pre-initialized.
Let's clear the register then on explicit controller reset to fulfil the
requirements in case of an error or having the CS left set by a bootloader
or another software.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The Tx and Rx data write/read procedure can be significantly simplified by
using Tx/Rx transfer lengths instead of the end pointers. By having the
Tx/Rx data leftover lengths (in the number of transfer words) we can get
rid of all subtraction and division operations utilized here and there in
the tx_max(), rx_max(), dw_writer() and dw_reader() methods. Such
modification will not only give us the more optimized IO procedures, but
will make the data IO methods much more readable than before.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI controller can be used by the two SPI core interfaces:
traditional SPI transfers and SPI memory operations. The controller needs
to be accordingly configured at runtime when the corresponding operations
are executed. In order to do that for the both interfaces from a single
function we introduce a new data wrapper for the transfer mode, data
width, number of data frames (for the automatic data transfer) and the bus
frequency. It will be used by the update_config() method to tune the DW
APB SSI up.
The update_config() method is made exported to be used not only by the DW
SPI core driver, but by the glue layer drivers too. This will be required
in a coming further commit.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DWC SSI core is supported by means of setting up the
core-specific update_cr0() callback. It isn't suitable for multiple
reasons. First of all having exported several methods doing the same thing
but for different chips makes the code harder to maintain. Secondly the
spi-dw-core driver exports the methods, then the spi-dw-mmio driver sets
the private data callback with one of them so to be called by the core
driver again. That makes the code logic too complicated. Thirdly using
callbacks for just updating the CR0 register is problematic, since in case
if the register needed to be updated from different parts of the code,
we'd have to create another callback (for instance the SPI device-specific
parameters don't need to be calculated each time the SPI transfer is
submitted, so it's better to pre-calculate the CR0 data at the SPI-device
setup stage).
So keeping all the above in mind let's discard the update_cr0() callbacks,
define a generic and static dw_spi_update_cr0() method and create the
DW_SPI_CAP_DWC_SSI capability, which when enabled would activate the
alternative CR0 register layout.
While at it add the comments to the code path of the normal DW APB SSI
controller setup to make the dw_spi_update_cr0() method looking coherent.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally I intended to merge a dedicated Baikal-T1 System Boot SPI
Controller driver into the kernel and leave the DW APB SSI driver
untouched. But after a long discussion (see the link at the bottom of the
letter) Mark and Andy persuaded me to integrate what we developed there
into the DW APB SSI core driver to be useful for another controllers,
which may have got the same peculiarities/problems as ours:
- No IRQ.
- No DMA.
- No GPIO CS, so a native CS is utilized.
- small Tx/Rx FIFO depth.
- Automatic CS assertion/de-assertion.
- Slow system bus.
All of them have been fixed in the framework of this patchset in some
extent at least for the SPI memory operations. As I expected it wasn't
that easy and the integration took that many patches as you can see from
the subject. Though some of them are mere cleanups or weakly related with
the subject fixes, but we just couldn't leave the code as is at some
places since we were working with the DW APB SSI driver anyway. Here is
what we did to fix the original DW APB SSI driver, to make it less messy.
First two patches are just cleanups to simplify the DW APB SSI device
initialization a bit. We suggest to discard the IRQ threshold macro as
unused and use a ternary operator to initialize the set_cs callback
instead of assigning-and-updating it.
Then we've discovered that the n_bytes field of the driver private data is
used by the DW APB SSI IRQ handler, which requires it to be initialized
before the SMP memory barrier and to be visible from another CPUs. Speaking
about the SMP memory barrier. Having one right after the shared resources
initialization is enough and there is no point in using the spin-lock to
protect the Tx/Rx buffer pointers. The protection functionality is
redundant there by the driver design. (Though I have a doubt whether the
SMP memory barrier is also required there because the normal IO-methods
like readl/writel implies a full memory barrier. So any memory operations
performed before them are supposed to be seen by devices and another CPUs.
See the patch log for details of my concern.)
Thirdly we've found out that there is some confusion in the IRQs
masking/unmasking/clearing in the SPI-transfer procedure. Multiple interrupts
are unmasked on the SPI-transfer initialization, but just TXEI is only
masked back on completion. Similarly IRQ status isn't cleared on the
controller reset, which actually makes the reset being not full and errors
prone in the controller probe procedure.
Another very important optimization is using the IO-relaxed accessors in
the dw_read_io_reg()/dw_write_io_reg() methods. Since the Tx/Rx FIFO data
registers are the most frequently accessible controller resource, using
relaxed accessors there will significantly improve the data read/write
performance. At least on Baikal-T1 SoC such modification opens up a way to
have the DW APB SSI controller working with higher SPI bus speeds, than
without it.
Fifthly we've made an effort to cleanup the code using the SPI-device
private data - chip_data. We suggest to remove the chip type from there
since it isn't used and isn't implemented right anyway. Then instead of
having a bus speed, clock divider, transfer mode preserved there, and
recalculating the CR0 fields of the SPI-device-specific phase, polarity
and frame format each time the SPI transfer is requested, we can save it
in the chip_data instance. By doing so we'll make that structure finally
used as it was supposed to by design (see the spi-fsl-dspi.c, spi-pl022.c,
spi-pxa2xx.c drivers for examples).
Sixthly instead of having the SPI-transfer specific CR0-update callback,
we suggest to implement the DW APB SSI controller capabilities approach.
By doing so we can now inject the vendor-specific peculiarities in
different parts of the DW APB SSI core driver (which is required to
implement both SPI-transfers and the SPI memory operations). This will
also make the code less confusing like defining a callback in the core
driver, setting it up in the glue layer, then calling it from the core
driver again. Seeing the small capabilities implementation embedded
in-situ is more readable than tracking the callbacks assignments. This
will concern the CS-override, Keembay master setup, DW SSI-specific CR0
registers layout capabilities.
Seventhly since there are going to be two types of the transfers
implemented in the DW APB SSI core driver, we need a common method to set
the controller configuration like, Tx/Rx-mode, bus speed, data frame size
and number of data frames to read in case of the memory operations. So we
just detached the corresponding code from the SPI-transfer-one method and
made it to be a part of the new dw_spi_update_config() function, which is
former update_cr0(). Note that the new method will be also useful for the
glue drivers, which due to the hardware design need to create their own
memory operations (for instance, for the dirmap-operations provided in the
Baikal-T System Boot SPI controller driver).
Eighthly it is the data IO procedure and IRQ-based SPI-transfer
implementation refactoring. The former one will look much simpler if the
buffers initial pointers and the buffers length data utilized instead of
the Tx/Rx buffers start and end pointers. The later one currently lacks of
valid execution at the final stage of the SPI-transfer. So if there is no
data left to send, but there is still data which needs to be received, the
Tx FIFO Empty IRQ will constantly happen until all of the requested
inbound data is received. So we suggest to fix that by taking the Rx FIFO
Empty IRQ into account.
Ninthly it's potentially errors prone to enable the DW APB SSI interrupts
before enabling the chip. It specifically concerns a case if for some
reason the DW APB SSI IRQs handler is executed before the controller is
enabled. That will cause a part of the outbound data loss. So we suggest
to reverse the order.
Tenthly in order to be able to pre-initialize the Tx FIFO with data and
only the start the SPI memory operations we need to have any CS
de-activated. We'll fulfil that requirement by explicitly clearing the CS
on the SPI transfer completion and at the explicit controller reset.
Then seeing all the currently available and potentially being created
types of the SPI transfers need to perform the DW APB SSI controller
status register check and the errors handler procedure, we've created a
common method for all of them.
Eleventhly if before we've mostly had a series of fixups, cleanups and
refactorings, here we've finally come to the new functionality
implementation. It concerns the poll-based transfer (as Baikal-T1 System
Boot SPI controller lacks a dedicated IRQ lane connected) and the SPI
memory operations implementation. If the former feature is pretty much
straightforward (see the patch log for details), the later one is a bit
tricky. It's based on the EEPROM-read (write-then-read) and the Tx-only
modes of the DW APB SSI controller, which as performing the automatic data
read and write let's us to implement the faster IO procedure than using
the Tx-Rx-mode-based approach. Having the memory-operations implemented
that way is the best thing we can currently do to provide the errors-less
SPI transfers to SPI devices with native CS attached.
Note the approach utilized here to develop the SPI memory operations can
be also used to create the "automatic CS toggle problem"-free(ish) SPI
transfers (combine SPI-message transfers into two buffers, disable
interrupts, push-pull the combined data). But we don't provide a solution
in the framework of this patchset. It is a matter of a dedicated one,
which we currently don't intend to spend our time on.
Finally at the closure of the this patchset you'll find patches, which
provide the Baikal-T1-specific DW APB SSI controllers support. The SoC has
got three SPI controllers. Two of them are pretty much normal DW APB SSI
interfaces: with IRQ, DMA, FIFOs of 64 words depth, 4x CSs. But the third
one as being a part of the Baikal-T1 System Boot Controller has got a very
limited resources: no IRQ, no DMA, only a single native chip-select and
Tx/Rx FIFOs with just 8 words depth available. In order to provide a
transparent initial boot code execution the System Boot SPI Controller is
also utilized by an vendor-specific IP-block, which exposes an SPI flash
memory direct mapping interface. Please see the corresponding patch for
details.
Link: https://lore.kernel.org/linux-spi/20200508093621.31619-1-Sergey.Semin@baikalelectronics.ru/
[1] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: wuxu.wu <wuxu.wu@huawei.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (30):
spi: dw: Discard IRQ threshold macro
spi: dw: Use ternary op to init set_cs callback
spi: dw: Initialize n_bytes before the memory barrier
Revert: spi: spi-dw: Add lock protect dw_spi rx/tx to prevent
concurrent calls
spi: dw: Clear IRQ status on DW SPI controller reset
spi: dw: Disable all IRQs when controller is unused
spi: dw: Use relaxed IO-methods to access FIFOs
spi: dw: Discard DW SSI chip type storages
spi: dw: Convert CS-override to DW SPI capabilities
spi: dw: Add KeemBay Master capability
spi: dw: Add DWC SSI capability
spi: dw: Detach SPI device specific CR0 config method
spi: dw: Update SPI bus speed in a config function
spi: dw: Simplify the SPI bus speed config procedure
spi: dw: Update Rx sample delay in the config function
spi: dw: Add DW SPI controller config structure
spi: dw: Refactor data IO procedure
spi: dw: Refactor IRQ-based SPI transfer procedure
spi: dw: Perform IRQ setup in a dedicated function
spi: dw: Unmask IRQs after enabling the chip
spi: dw: Discard chip enabling on DMA setup error
spi: dw: De-assert chip-select on reset
spi: dw: Explicitly de-assert CS on SPI transfer completion
spi: dw: Move num-of retries parameter to the header file
spi: dw: Add generic DW SSI status-check method
spi: dw: Add memory operations support
spi: dw: Introduce max mem-ops SPI bus frequency setting
spi: dw: Add poll-based SPI transfers support
dt-bindings: spi: dw: Add Baikal-T1 SPI Controllers
spi: dw: Add Baikal-T1 SPI Controller glue driver
.../bindings/spi/snps,dw-apb-ssi.yaml | 33 +-
drivers/spi/Kconfig | 29 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-dw-bt1.c | 339 +++++++++
drivers/spi/spi-dw-core.c | 642 ++++++++++++++----
drivers/spi/spi-dw-dma.c | 16 +-
drivers/spi/spi-dw-mmio.c | 36 +-
drivers/spi/spi-dw.h | 85 ++-
8 files changed, 960 insertions(+), 221 deletions(-)
create mode 100644 drivers/spi/spi-dw-bt1.c
--
2.27.0
There is no point in having the commit 19b61392c5 ("spi: spi-dw: Add
lock protect dw_spi rx/tx to prevent concurrent calls") applied. The
commit author made an assumption that the problem with the rx data
mismatch was due to the lack of the data protection. While most likely it
was caused by the lack of the memory barrier. So having the
commit bfda044533 ("spi: dw: use "smp_mb()" to avoid sending spi data
error") applied would be enough to fix the problem.
Indeed the spin unlock operation makes sure each memory operation issued
before the release will be completed before it's completed. In other words
it works as an implicit one way memory barrier. So having both smp_mb()
and the spin_unlock_irqrestore() here is just redundant. One of them would
be enough. It's better to leave the smp_mb() since the Tx/Rx buffers
consistency is provided by the data transfer algorithm implementation:
first we initialize the buffers pointers, then make sure the assignments
are visible by the other CPUs by calling the smp_mb(), only after that
enable the interrupt, which handler uses the buffers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In a further commit we'll have to get rid of the update_cr0() callback and
define a DW SSI capability instead. Since Keem Bay master/slave
functionality is controller by the CTRL0 register bitfield, we need to
first move the master mode selection into the internal corresponding
update_cr0 method, which would be activated by means of the dedicated
DW_SPI_CAP_KEEMBAY_MST capability setup.
Note this will be also useful if the driver will be ever altered to
support the DW SPI slave interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several vendor-specific versions of the DW SPI controllers,
each of which may have some peculiarities with respect to the original
IP-core. Seeing it has already caused adding flags and a callback into the
DW SPI private data, let's introduce a generic capabilities interface to
tune the generic DW SPI controller driver up in accordance with the
particular controller specifics. It's done by converting a simple
Alpine-specific CS-override capability into the DW SPI controller
capability activated by setting the DW_SPI_CAP_CS_OVERRIDE flag.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Keeping SPI peripheral devices type is pointless since first it hasn't
been functionally utilized by any of the client drivers/code and second it
won't work for Microwire type at the very least. Moreover there is no
point in setting up the type by means of the chip-data in the modern
kernel. The peripheral devices with specific interface type need to be
detected in order to activate the corresponding frame format. It most
likely will require some peripheral device specific DT property or
whatever to find out the interface protocol. So let's remove the serial
interface type fields from the DW APB SSI controller and the SPI
peripheral device private data.
Note we'll preserve the explicit SSI_MOTO_SPI interface type setting up to
signify the only currently supported interface protocol.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In accordance with [1] the relaxed methods are guaranteed to be ordered
with respect to other accesses from the same CPU thread to the same
peripheral. This is what we need during the data read/write from/to the
controller FIFOs being executed within a single IRQ handler or a kernel
task.
Such optimization shall significantly speed the data reader and writer up.
For instance, the relaxed IO-accessors utilization on Baikal-T1 lets the
driver to support the SPI memory operations with bus frequency three-fold
faster than if normal IO-accessors would be used.
[1] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It turns out the IRQ status isn't cleared after switching the controller
off and getting it back on, which may cause raising false error interrupts
if controller has been unsuccessfully used by, for instance, a bootloader
before the driver is loaded. Let's explicitly clear the interrupts status
in the dedicated controller reset method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112914.26501-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In case if at least one of the requested DMA engine channels doesn't
support the hardware accelerated SG list entries traverse, the DMA driver
will most likely work that around by performing the IRQ-based SG list
entries resubmission. That might and will cause a problem if the DMA Tx
channel is recharged and re-executed before the Rx DMA channel. Due to
non-deterministic IRQ-handler execution latency the DMA Tx channel will
start pushing data to the SPI bus before the Rx DMA channel is even
reinitialized with the next inbound SG list entry. By doing so the DMA
Tx channel will implicitly start filling the DW APB SSI Rx FIFO up, which
while the DMA Rx channel being recharged and re-executed will eventually
be overflown.
In order to solve the problem we have to feed the DMA engine with SG
list entries one-by-one. It shall keep the DW APB SSI Tx and Rx FIFOs
synchronized and prevent the Rx FIFO overflow. Since in general the SPI
tx_sg and rx_sg lists may have different number of entries of different
lengths (though total length should match) we virtually split the
SG-lists to the set of DMA transfers, which length is a minimum of the
ordered SG-entries lengths.
The solution described above is only executed if a full-duplex SPI
transfer is requested and the DMA engine hasn't provided channels with
hardware accelerated SG list traverse capability to handle both SG
lists at once.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200920112322.24585-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This add support for the RX_SAMPLE_DLY register. If enabled in the
Designware IP, it allows tuning of the rx data signal by means of an
internal rx sample fifo.
The register is controlled by the rx-sample-delay-ns DT property,
which is defined per SPI slave as well on controller level.
The controller level rx-sample-delay-ns will apply to all slaves
without the property explicitly defined.
The register is located at offset 0xf0, and if the option is not
enabled in the IP, changing the register will have no effect. The
register will only be written if any slave defines a nonzero value
(after scaling by the clock period).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-2-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This member has exactly the same value as n_bytes of the DW SPI private
data object, it's calculated at the same point of the transfer method,
n_bytes isn't changed during the whole transfer, and they even serve for
the same purpose - keep number of bytes per transfer word, though the
dma_width is used only to calculate the DMA source/destination addresses
width, which n_bytes could be also utilized for. Taking all of these
into account let's replace the dma_width member usage with n_bytes one
and remove the former.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing the "void *priv" member of the dw_spi data structure is unused
let's remove it. The glue-layers can embed the DW APB SSI controller
descriptor into their private data object. MMIO driver for instance
already utilizes that design pattern.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Having them declared is redundant since each struct dw_dma_chan has
the same structure embedded and the structure from the passed dma_chan
private pointer will be copied there as a result of the next calls
chain:
dma_request_channel() -> find_candidate() -> dma_chan_get() ->
device_alloc_chan_resources() = dwc_alloc_chan_resources() ->
dw_dma_filter().
So just remove the static dw_dma_chan structures and use a locally
declared data instance with dst_id/src_id set to the same values as
the static copies used to have.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is superfluous in all cases where it's being used, i.e.
* ->can_dma() won't be called without dma_inited == 1
* DMA ->exit() callback can rely on txchan and rxchan variables
So, get rid of dma_inited flag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200507115449.8093-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Elkhart Lake PSE SPI is capable to utilize PSE DMA engine which is described
in ACPI. With help of acpi-dma module the support becomes a generic one.
Thus, add Elkhart Lake PSE DMA support and generic DMA hooks in SPI DesignWare
driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases, one of which is coming soon, we would like to have
a struct device pointer to request DMA channel. For this purpose
propagate it to ->dma_init() callback in DMA ops.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to prepare driver for the extension to support newer hardware,
add 'mfld' suffix to some related functions.
While here, move DMA parameters assignment under existing #ifdef
CONFIG_SPI_DW_MID_DMA.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
spi-dw-mid.c along with spi-dw.h are direct users of irqreturn.h
and nothing else is being used from interrupt.h. So, switch them
to use the former instead of latter one.
While here, move the header under #ifdef CONFIG_SPI_DW_MID_DMA
in spi-dw-mid.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds update_cr0() callback, in struct dw_spi.
Existing code that configure register CTRLR0 is moved into a new
function, dw_spi_update_cr0(), and this will be the default.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will fix typo in the register name used in the source code,
to be consistent with the register name used in the databook.
Databook: DW_apb_ssi_databook.pdf version 4.01a
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-2-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The path of code using this struct is unused since there is no more user
of this. Remove code and struct definition.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200416110916.22633-1-cleger@kalray.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
dw_spi_irq() and dw_spi_transfer_one concurrent calls.
I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null,
dw->len==4, and dw->tx_end==1.
When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one
may concurrent visit dw_spi, so I think dw_spi structure lack of protection.
Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq,
store dw rx/tx instructions and other cores handle irq load dw rx/tx
instructions may out of order.
[ 1025.321302] Call trace:
...
[ 1025.321319] __crash_kexec+0x98/0x148
[ 1025.321323] panic+0x17c/0x314
[ 1025.321329] die+0x29c/0x2e8
[ 1025.321334] die_kernel_fault+0x68/0x78
[ 1025.321337] __do_kernel_fault+0x90/0xb0
[ 1025.321346] do_page_fault+0x88/0x500
[ 1025.321347] do_translation_fault+0xa8/0xb8
[ 1025.321349] do_mem_abort+0x68/0x118
[ 1025.321351] el1_da+0x20/0x8c
[ 1025.321362] dw_writer+0xc8/0xd0
[ 1025.321364] interrupt_transfer+0x60/0x110
[ 1025.321365] dw_spi_irq+0x48/0x70
...
Signed-off-by: wuxu.wu <wuxu.wu@huawei.com>
Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using device name it was suggested that bus number was more
appropriate to differentiate debugfs names. Also reduce buffer size to
more realistic 32 bytes instead of 128.
When request_irq is called the bus number may not be assigned. Therefore
the irq name was not unique when dynamic bus number was being used.
As per most of the spi drivers use the device name instead. No other
use of dws->name could be found so it was removed.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add current master clock to dws struct and compare it against the
requestedtransfer speed. Update clock divider only if necessary.
Signed-off-by: Matthias Seidel <kernel@mseidel.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_spi_dma_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit
accesses") changed all 16bit accesses in the DW_apb_ssi driver to 32bit.
This, unfortunately, breaks data register access on picoXcell, where the
DW IP needs data register accesses to be word accesses (all other
accesses appear to be OK).
This change introduces a new master variable to allow interface drivers
to specify that 16bit data transfer I/O is required. This change also
introduces the ability to set this variable via device tree bindings in
the MMIO interface driver. Both the core and the MMIO interface driver
default to the current 32bit behaviour.
Before this change, on a picoXcell pc3x3:
spi_master spi32766: interrupt_transfer: fifo overrun/underrun
m25p80 spi32766.0: error -5 reading 9f
m25p80: probe of spi32766.0 failed with error -5
After this change:
m25p80 spi32766.0: m25p40 (512 Kbytes)
Fixes: dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit accesses")
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Altera's Arria10 SoC interconnect requires a 32-bit write for APB
peripherals. The current spi-dw driver uses 16-bit accesses in
some locations. This patch converts all the 16-bit reads and
writes to 32-bit reads and writes.
Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]
[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)
Request for test with platforms using the DesignWare SPI IP.
Tested On:
Altera CycloneV development kit
Altera Arria10 development kit
Compile tested for build errors on x86_64 (allyesconfigs)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Damien Le Moal