Synopsys DesignWare core based PCIe controllers in Tegra234 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://lore.kernel.org/r/20220629060435.25297-9-vidyas@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
callers of tegra_xusb_find_port_node() function only do NULL checking for
the return value. return NULL instead of ERR_PTR(-ENOMEM) to keep
consistent.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211213020507.1458-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When these are not referenced, gcc prints a harmless warning:
drivers/phy/tegra/xusb.c:1286:12: error: 'tegra_xusb_padctl_resume_noirq' defined but not used [-Werror=unused-function]
1286 | static int tegra_xusb_padctl_resume_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/phy/tegra/xusb.c:1276:12: error: 'tegra_xusb_padctl_suspend_noirq' defined but not used [-Werror=unused-function]
1276 | static int tegra_xusb_padctl_suspend_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c545a90567 ("phy: tegra: xusb: Add sleepwalk and suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721152550.2976003-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support XUSB host controller ELPG, this commit moves VBUS control
.phy_power_on()/.phy_power_off() to .phy_init()/.phy_exit().
When XUSB host controller enters ELPG, host driver invokes
.phy_power_off(), VBUS should remain ON so that USB devices will not
disconnect. VBUS can be turned OFF when host driver invokes
.phy_exit() which indicates disabling a USB port.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit implements Tegra210 XUSB PADCTL wake and sleepwalk
routines. Sleepwalk logic is in PMC (always-on) hardware block.
PMC driver provides managed access to the sleepwalk registers
via regmap framework.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds sleepwalk/wake and suspend/resume interfaces
to Tegra XUSB PHY driver.
Tegra XUSB host controller driver makes use of sleepwalk functions
to enable/disable sleepwalk circuit which is in always-on partition
and can respond to USB resume signals when controller is not powered.
Sleepwalk can be enabled/disabled for any USB UPHY individually.
- tegra_xusb_padctl_enable_phy_sleepwalk()
- tegra_xusb_padctl_disable_phy_sleepwalk()
Tegra XUSB host controller driver makes use of wake functions to
enable/disable/query wake circuit which is in always-on partition
can wake system up when USB resume happens.
Wake circuit can be enabled/disabled for any USB PHY individually.
- tegra_xusb_padctl_enable_phy_wake()
- tegra_xusb_padctl_disable_phy_wake()
- tegra_xusb_padctl_remote_wake_detected()
This commit also adds two system suspend stubs that can be used to
save and restore XUSB PADCTL context during system suspend and
resume.
- tegra_xusb_padctl_suspend_noirq()
- tegra_xusb_padctl_resume_noirq()
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As per Tegra210 TRM, before changing lane assignments, driver should
keep lanes in IDDQ and sleep state; after changing lane assignments,
driver should bring lanes out of IDDQ.
This commit implements the required operations.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit is a preparation for enabling XUSB SC7 support.
It rearranges Tegra210 XUSB PADCTL UPHY initialization sequence,
for the following reasons:
1. PLLE hardware power sequencer has to be enabled only after both
PEX UPHY PLL and SATA UPHY PLL are initialized.
tegra210_uphy_init() -> tegra210_pex_uphy_enable()
-> tegra210_sata_uphy_enable()
-> tegra210_plle_hw_sequence_start()
-> tegra210_aux_mux_lp0_clamp_disable()
2. At cold boot and SC7 exit, the following bits must be cleared after
PEX/SATA lanes are out of IDDQ (IDDQ_DISABLE=1).
a. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN,
b. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_CLAMP_EN_EARLY
c. XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_VCORE_DOWN
tegra210_pex_uphy_enable() and tegra210_sata_uphy_enable() are in
charge of bringing lanes out of IDDQ, and then AUX_MUX_LP0_* bits
will be cleared by tegra210_aux_mux_lp0_clamp_disable().
3. Once UPHY PLL hardware power sequencer is enabled, do not assert
reset to PEX/SATA PLLs, otherwise UPHY PLL operation will be broken.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The programming sequence in tegra210_usb3_port_enable() is required
for both cold boot and SC7 exit, and must be performed only after
PEX/SATA UPHY is initialized. Therefore, this commit moves the
programming sequence to tegra210_usb3_phy_power_on(). PCIE/SATA phy
.power_on() stub will invoke tegra210_usb3_phy_power_on() if the lane
is assigned for XUSB super-speed.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
-----BEGIN PGP SIGNATURE-----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=EFMp
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.11
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
* tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
drm/mediatek: avoid dereferencing a null hdmi_phy on an error message
phy: ingenic: depend on HAS_IOMEM
phy: mediatek: statify mtk_hdmi_phy_driver
dt-bindings: phy: Convert Broadcom SATA PHY to YAML
devicetree: phy: rockchip-emmc add output-tapdelay-select
phy: rockchip-emmc: output tap delay dt property
PHY: Ingenic: Add USB PHY driver using generic PHY framework.
dt-bindings: USB: Add bindings for Ingenic JZ4775 and X2000.
USB: PHY: JZ4770: Remove unnecessary function calls.
devicetree: phy: rockchip-emmc: pulldown property
phy: rockchip: set pulldown for strobe line in dts
phy: renesas: rcar-gen3-usb2: disable runtime pm in case of failure
phy: mediatek: allow compile-testing the hdmi phy
phy/rockchip: Make PHY_ROCKCHIP_INNO_HDMI depend on HAS_IOMEM to fix build error
phy: samsung: Merge Kconfig for Exynos5420 and Exynos5250
phy: ralink: phy-mt7621-pci: set correct name in MODULE_DEVICE_TABLE macro
phy: ralink: phy-mt7621-pci: drop 'COMPILE_TEST' from Kconfig
phy: mediatek: Make PHY_MTK_{XSPHY, TPHY} depend on HAS_IOMEM and OF_ADDRESS to fix build errors
phy: tegra: xusb: Fix usb_phy device driver field
phy: amlogic: replace devm_reset_control_array_get()
...
Deferred probe is an expected return value for devm_regulator_bulk_get().
Given that the driver deals with it properly, there's no need to output a
warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: JC Kuo <jckuo@nvidia.com>
Link: https://lore.kernel.org/r/20201111103708.152566-1-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only usage of tegra_xusb_pad_type and tegra_xusb_port_type is to
assign their address to the type field in the device struct, which is a
const pointer. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201109215844.167954-1-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The usb_get_maximum_speed() function is part of the usb-common module,
so enable it by selecting the corresponding Kconfig symbol.
While at it, also make sure to depend on USB_SUPPORT because USB_PHY
requires that. This can lead to Kconfig conflicts if USB_SUPPORT is not
enabled while attempting to enable PHY_TEGRA_XUSB.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200330101038.2422389-1-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_port_unregister':
xusb.c:(.text+0x2ac): undefined reference to `usb_remove_phy'
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_setup_ports':
xusb.c:(.text+0xf30): undefined reference to `usb_add_phy_dev'
PHY_TEGRA_XUSB should select USB_PHY because it uses symbols defined in
the code enabled by that.
Fixes: 23babe30fb45d ("phy: tegra: xusb: Add usb-phy support")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device-managed allocation API doesn't work well with the life-cycle
of device objects. Since ports have device objects allocated within, it
can lead to situations where these devices need to stay around until
after their parent pad controller has been unbound from its driver. The
device-managed memory allocated for the port objects will, however, get
freed when the pad controller unbinds from the driver. This can cause
use-after-free errors down the road.
Note that the device is deleted as part of the driver unbind operation,
so there isn't much that can be done with it after that point, but the
memory still needs to stay around to ensure none of the references are
invalidated.
One situation where this arises is when a VBUS supply is associated with
a USB 2 or 3 port. When that supply is released using regulator_put() an
SRCU call will queue the release of the device link connecting the port
and the regulator after a grace period. This means that the regulator is
going to keep on to the last reference of the port device even after the
pad controller driver was unbound (which is when the memory backing the
port device is freed).
Fix this by allocating port objects using non-device-managed memory. Add
release callbacks for these objects so that their memory gets freed when
the last reference goes away. This decouples the port devices' lifetime
from the "active" lifetime of the pad controller (i.e. the time during
which the pad controller driver owns the device).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devices are created for each port of the XUSB pad controller. Each USB 2
and USB 3 port can potentially have an associated VBUS power supply that
needs to be removed when the device is removed.
Since port devices never bind to a driver, the driver core will not get
to perform the cleanup of device-managed resources that usually happens
on driver unbind.
Now, the driver core will also perform device-managed resource cleanup
for driver-less devices when they are released. However, when a device
link is created between the regulator and the port device, as part of
regulator_get(), the regulator takes a reference to the port device and
prevents it from being released unless regulator_put() is called, which
will never happen.
Avoid this by using the non-device-managed API and manually releasing
the regulator reference when the port is unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on USB 2 phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB host, device mode driver requires the USB 3 companion port
number for corresponding USB 2 port. Add API to retrieve the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For USB 2 ports that has usb-role-switch enabled, add usb-phy for
corresponding USB 2 phy. USB role changes from role switch are then
updated to corresponding host and device mode drivers via usb-phy notifier
block.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If usb-role-switch property is present in USB 2 port, register
usb-role-switch to receive usb role changes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new regulator helper instead of a for loop.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On Tegra210, usb2 only otg/peripheral ports dont work in device mode.
They need an assosciated usb3 port to work in device mode. Identify
an unused usb3 port and assign it as a fake USB3 port to USB2 only
port whose mode is otg/peripheral.
Based on work by BH Hsieh <bhsieh@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Configure the port capabilities based on usb_dr_mode settings.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The local variable @priv is set but not used, can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Thierry Reding <treding@nvidia.com>
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+dGx
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2-rc
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: tegra: xusb: Add Tegra210 PLL power supplies
phy: tegra: xusb: Add Tegra124 PLL power supplies
dt-bindings: phy: tegra-xusb: List PLL power supplies
phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal
phy: renesas: rcar-gen2: Fix memory leak at error paths
phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
The Tegra210 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Tegra124 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.
Based on work by JC Kuo <jckuo@nvidia.com>.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The new helper returns index of the matching string in an array.
We are going to use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The reason why this was originally commented out is no longer clear. The
UPHY driver for SATA works fine with or without this change. The reset
value of the XDIGCLK_EN bit is 0, so unless programmed by the bootloader
this shouldn't make a difference anyway.
Define a macro for this bit and uncomment the code. This also fixes a
coverity issue brought to my attention by Rohith because not only is the
XDIGCLK_EN field modification commented out, but also the register write
which causes none of the earlier modifications of the register value to
be written to the register and the value being overwritten.
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The assignment of map to itself is redundant and can be removed.
Detected with Coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix child-node lookups during probe, which ended up searching the whole
device tree depth-first starting at the parents rather than just
matching on their children.
To make things worse, some parent nodes could end up being being
prematurely freed (by tegra_xusb_pad_register()) as
of_find_node_by_name() drops a reference to its first argument.
Fixes: 53d2a715c2 ("phy: Add Tegra XUSB pad controller support")
Cc: stable <stable@vger.kernel.org> # 4.7
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Vidya Sagar