fixups for multicolor. Clevo-mail driver got disabled, it needs API
fix.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYvEUpgAKCRAw5/Bqldv6
8vDGAKCYdETEgfPsExMizqACzkcQWYzpUgCfetiY56Wkr1vLx+kCBvHS9m6wC+8=
=MT+Z
-----END PGP SIGNATURE-----
Merge tag 'leds-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"A new driver for bcm63138, is31fl319x updates, fixups for multicolor.
The clevo-mail driver got disabled, it needs an API fix"
* tag 'leds-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (23 commits)
leds: is31fl319x: use simple i2c probe function
leds: is31fl319x: Fix devm vs. non-devm ordering
leds: is31fl319x: Make use of dev_err_probe()
leds: is31fl319x: Make use of device properties
leds: is31fl319x: Cleanup formatting and dev_dbg calls
leds: is31fl319x: Add support for is31fl319{0,1,3} chips
leds: is31fl319x: Move chipset-specific values in chipdef struct
leds: is31fl319x: Use non-wildcard names for vars, structs and defines
leds: is31fl319x: Add missing si-en compatibles
dt-bindings: leds: pwm-multicolor: document max-brigthness
leds: turris-omnia: convert to use dev_groups
leds: leds-bcm63138: get rid of LED_OFF
leds: add help info about BCM63138 module name
dt-bindings: leds: leds-bcm63138: unify full stops in descriptions
dt-bindings: leds: lp50xx: fix LED children names
dt-bindings: leds: class-multicolor: reference class directly in multi-led node
leds: bcm63138: add support for BCM63138 controller
dt-bindings: leds: add Broadcom's BCM63138 controller
leds: clevo-mail: Mark as broken pending interface fix
leds: pwm-multicolor: Support active-low LEDs
...
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
When non-devm resources are allocated they mustn't be followed by
devm allocations, otherwise it will break the tear down ordering
and might lead to crashes or other bugs during ->remove() stage.
Fix this by wrapping mutex_destroy() call with
devm_add_action_or_reset().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Simplify the error handling in probe function by switching from
dev_err() to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Fix remaining non-standard place for comments.
Remove remaining dev_dbg after regmap_read in is31fl3196_brightness_set.
Remove __func__ in dev_dbg calls, instead adding "channel" string to
describe the first displayed value.
Change remaining container_of() call to be on one line,
as well as a few others.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Allow setting chips' specifics in chipdef struct by adding fields for:
- the reset register address
- a pointer to a regmap_config struct
- a pointer to a brightness_set function
- current default, min and max values
- a boolean to distinguish 319{0,1,3} and 319{6,9} chips
and use those fields in places where distinction has to be made.
The fields for 319{0,1,3} still point to 319{6,9} values.
No functional change.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The driver core supports the ability to handle the creation and removal
of device-specific sysfs files in a race-free manner. Take advantage of
that by converting this driver to use this by moving the sysfs
attributes into a group and assigning the dev_groups pointer to it.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux-leds@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The whole "enum led_brightness" is marked as obsolete. Replace it with a
(non-)zero check.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
It's what we do for all other LEDs drivers.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
It's a new controller first introduced in BCM63138 SoC. Later it was
also used in BCM4908, some BCM68xx and some BCM63xxx SoCs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add support for LEDs wired up to light when the PWM output is low, just
like the regular PWM LEDs.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
When requesting a PWM it might return -EPROBE_DEFER if it hasn't probed
yet. This is not an error, so just propagate the -EPROBE_DEFER without
logging anything. There is already dev_err_probe for exactly this
situation.
Fixes: 9fa2762110 ("leds: Add PWM multicolor driver")
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
On Apollo Lake the pinctrl drivers will now come up without ACPI. Use
that instead of open coding it.
Create a new driver for that which can later be filled with more GPIO
based models, and which has different dependencies.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
The leds-trigger-pattern documentation describes how the brightness of
the LED should transition linearly from one brightness value to the
next, over the given delta_t.
But the pattern engine in the Qualcomm LPG hardware only supports
holding the brightness for each entry for the period.
This subset of patterns can be represented in the leds-trigger-pattern
by injecting zero-time transitions after each entry in the pattern,
resulting in a pattern that pattern that can be rendered by the LPG.
Rework LPG pattern interface to require these zero-time transitions, to
make it comply with this subset of patterns and reject the patterns it
can't render.
Fixes: 24e2d05d1b ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Returning an error value from an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As stk3310_set_state() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, don't pass the error value up the stack. Instead continue
to clean up and return 0.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Qualcomm LPG driver fails to probe unless PWM support is enabled so
add the missing Kconfig dependency.
Fixes: 24e2d05d1b ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Make the AUX pin optional, since it isn't a core part of functionality,
and the device is designed to be operational with only one CTRL pin.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use dev_err_probe instead of dev_err to avoid duplicate error
messages if the GPIO allocation makes the probe defer.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't make
a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more helpful
message if a problem occurs and return 0 to suppress the generic message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The drivers/leds/rgb subdirectory is relatively fresh, so we move this
new PWM multi-color driver into it.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
By allowing to group multiple monochrome PWM LEDs into multicolor LEDs,
all involved LEDs can be controlled in-sync. This enables using effects
using triggers, etc.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The regulator LED can easily be adapted to probe from the
device tree.
We switch led_classdev_register() to led_classdev_register_ext()
passing some struct led_init_data init_data that we leave NULL
save the fwnode if platform data isn't present so that it will be
populated from the device tree.
If we have platform data we set up the name from the platform
data but using init_data instead.
Cc: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Instead of repeating the hard to read &pdev->dev just create a
local struct device *dev in probe().
Cc: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Up to now pca9532_destroy_devices() returns always zero because it's
always called with data != NULL. Remove the never-taken error path and
make it return void which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add pm8350c compatible and lpg_data to the driver.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
with their output being routed to various other components, such as
current sinks or GPIOs.
Each LPG instance can operate on fixed parameters or based on a shared
lookup-table, altering the duty cycle over time. This provides the means
for hardware assisted transitions of LED brightness.
A typical use case for the fixed parameter mode is to drive a PWM
backlight control signal, the driver therefor allows each LPG instance
to be exposed to the kernel either through the LED framework or the PWM
framework.
A typical use case for the LED configuration is to drive RGB LEDs in
smartphones etc, for which the driver supports multiple channels to be
ganged up to a MULTICOLOR LED. In this configuration the pattern
generators will be synchronized, to allow for multi-color patterns.
The idea of modelling this as a LED driver ontop of a PWM driver was
considered, but setting the properties related to patterns does not fit
in the PWM API. Similarly the idea of just duplicating the lower bits in
a PWM and LED driver separately was considered, but this would not allow
the PWM channels and LEDs to be configured on a per-board basis. The
driver implements the more complex LED interface, and provides a PWM
interface on the side of that, in the same driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[On the Sony Xperia Nile Discovery, SDM630]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
that need review and did not make it.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYj+mOQAKCRAw5/Bqldv6
8pXqAJ9co9nkfU7H+VIdk4FWHp6w87fDCACeKRIOcG5eK50yoBhMGclvuuC7V5s=
=gSle
-----END PGP SIGNATURE-----
Merge tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major here, there are two drivers that need review and did not
make it into this round"
* tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: pca955x: Allow zero LEDs to be specified
leds: pca955x: Make the gpiochip always expose all pins
leds: simatic-ipc-leds: Don't directly deref ioremap_resource() returned ptr
leds: simatic-ipc-leds: Make simatic_ipc_led_mem_res static
leds: lm3692x: Return 0 from remove callback
leds: sgm3140: Add ocs,ocp8110 compatible
dt-bindings: vendor-prefixes: Add ocs prefix
dt-bindings: leds: common: fix unit address in max77693 example
It's valid to use the PCA955x devices just for GPIOs and not for LEDs.
In this case, as PCA955X_TYPE_GPIO is now equivalent to
PCA955X_TYPE_NONE, remove the test for whether we have any child nodes
specified in the devicetree.
A consequence of this is it's now possible to bind the driver to a
PCA955x device when dynamically instantiated through the I2C subsystem's
`new_device` interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The devicetree binding allows specifying which pins are GPIO vs LED.
Limiting the instantiated gpiochip to just these pins as the driver
currently does requires an arbitrary mapping between pins and GPIOs, but
such a mapping is not implemented by the driver. As a result,
specifying GPIOs in such a way that they don't map 1-to-1 to pin indexes
does not function as expected.
Establishing such a mapping is more complex than not and even if we did,
doing so leads to a slightly hairy userspace experience as the behaviour
of the PCA955x gpiochip would depend on how the pins are assigned in the
devicetree. Instead, always expose all pins via the gpiochip to provide
a stable interface and track which pins are in use.
Specifying a pin as `type = <PCA955X_TYPE_GPIO>;` in the devicetree
becomes a no-op.
I've assessed the impact of this change by looking through all of the
affected devicetrees as of the tag leds-5.15-rc1:
```
$ git grep -l 'pca955[0123]' $(find . -name dts -type d)
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
```
These are all IBM-associated platforms. I've analysed both the
devicetrees and schematics where necessary to determine whether any
systems hit the hazard of the current broken behaviour. For the most
part, the systems specify the pins as either all LEDs or all GPIOs, or
at least do so in a way such that the broken behaviour isn't exposed.
The main counter-point to this observation is the Everest system whose
devicetree describes a large number of PCA955x devices and in some cases
has pin assignments that hit the hazard. However, there does not seem to
be any use of the affected GPIOs in the userspace associated with
Everest.
Regardless, any use of the hazardous GPIOs in Everest is already broken,
so let's fix the interface and then fix any already broken userspace
with it.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Sparse (rightly) currently gives the following warning:
drivers/leds/simple/simatic-ipc-leds.c:155:40:
sparse: sparse: incorrect type in assignment (different address spaces)
expected void *static [toplevel] simatic_ipc_led_memory
got void [noderef] __iomem *
Fix this by changing the type of simatic_ipc_led_memory to void __iomem *
and use readl()/writel() to access it.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Gerd Haeussler <gerd.haeussler.ext@siemens.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
simatic_ipc_led_mem_res is not used outside of the driver, make it static.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The only difference between returning zero or a non-zero value is that
for the non-zero case the i2c will print a generic error message
("remove failed (-ESOMETHING), will be ignored").
In this case however the driver itself already emitted a more helpful
error message, so the additional error message isn't helpful at all.
The long-term goal is to make the i2c remove callback return void, making
all implementations return 0 is preparatory work for this change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
I had to rebase at last moment to fix wrong author of one
commit. Sorry about that.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYd8hdwAKCRAw5/Bqldv6
8m3sAKC20ddEFW04Mk45Tw72qSyud6vhwQCaAnQy6dcd+zV6LOxosgLZdtXkvx0=
=CU+X
-----END PGP SIGNATURE-----
Merge tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major is happening here"
* tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp55xx: initialise output direction from dts
ARM: dts: omap3-n900: Fix lp5523 for multi color
leds: ktd2692: Drop calling dev_of_node() in ktd2692_parse_dt
leds: lgm-sso: Get rid of duplicate of_node assignment
leds: tca6507: Get rid of duplicate of_node assignment
leds: leds-fsg: Drop FSG3 LED driver
leds: lp50xx: remove unused variable
dt-bindings: leds: Replace moonlight with indicator in mt6360 example
leds: led-core: Update fwnode with device_set_node
leds: tca6507: use swap() to make code cleaner
leds: Add mt6360 driver
dt-bindings: leds: Add bindings for MT6360 LED
Commit a5d3d1adc9 ("leds: lp55xx: Initialize enable GPIO direction to
output") attempts to fix this, but the fix did not work since at least
for the Nokia N900 the value needs to be set to HIGH, per the device
tree. So rather than hardcoding the value to a potentially invalid value
for some devices, let's set direction in lp55xx_init_device.
Fixes: a5d3d1adc9 ("leds: lp55xx: Initialize enable GPIO direction to output")
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Fixes: ac219bf3c9 ("leds: lp55xx: Convert to use GPIO descriptors")
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
output of dev_of_node() is already assigned to "np" variable in
ktd2692_parse_dt(). Use "np" variable to check if OF node is NULL
instead of calling dev_of_node() again.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Call graph:
--> sso_gpio_gc_init()
--> devm_gpiochip_add_data
--> devm_gpiochip_add_data_with_key
--> gpiochip_add_data_with_key()
--> of_gpio_dev_init()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Call graph:
--> tca6507_probe_gpios()
--> gpiochip_add_data()
--> gpiochip_add_data_with_key()
--> of_gpio_dev_init()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The board file using this driver has been deleted and the
FSG3 LEDs can be modeled using a system controller and some
register bit LEDs in the device tree so this driver is no
longer needed.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Krzysztof Hałasa <khalasa@piap.pl>
Cc: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
During code review this unused variable was found. Remove it.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Linus Torvalds