Add DT bindings for the Meson-AXG SoC Reset Controller include file,
and also slightly update documentation.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This branch contains platform-related driver updates for ARM and ARM64,
these are the areas that bring the changes:
New drivers:
- Driver support for Renesas R-Car V3M (R8A77970)
- Power management support for Amlogic GX
- A new driver for the Tegra BPMP thermal sensor
- A new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- The usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa, uniphier
and mediatek families.
- Updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi.
Changes specific to some ARM-based SoC
- The Freescale/NXP DPAA QBMan drivers from PowerPC can now work
on ARM as well.
- Several changes for power management on Broadcom SoCs
- Various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek
- Minor Cleanups for Samsung, TI OMAP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDhq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- add ARC AX10x support,
merged from a separate branch that is also included in the ARC tree
- add Stratix10 support via socfpga
- unify socfpga, stm32, sunxi, and zx2967 into simple-reset driver
- add Meson GX reset level control and remove an unneeded check
- add Uniphier PXs3 and ethernet reset controls
- add MT7622 reset control dt-bindings header
-----BEGIN PGP SIGNATURE-----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=yCoy
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.15' of git://git.pengutronix.de/git/pza/linux into next/drivers
Pull "Reset controller changes for v4.15" from Philipp Zabel:
- add ARC AX10x support,
merged from a separate branch that is also included in the ARC tree
- add Stratix10 support via socfpga
- unify socfpga, stm32, sunxi, and zx2967 into simple-reset driver
- add Meson GX reset level control and remove an unneeded check
- add Uniphier PXs3 and ethernet reset controls
- add MT7622 reset control dt-bindings header
* tag 'reset-for-4.15' of git://git.pengutronix.de/git/pza/linux:
reset: zx2967: use the reset-simple driver
reset: stm32: use the reset-simple driver
reset: socfpga: use the reset-simple driver
reset: sunxi: use reset-simple driver
reset: add reset-simple to unify socfpga, stm32, sunxi, and zx2967
reset: meson: remove unneeded check in meson_reset_reset
reset: meson: add level reset support for GX SoC family
reset: uniphier: add PXs3 reset data
reset: mediatek: add reset controller dt-bindings required header for MT7622 SoC
reset: socfpga: build the reset-socfpga for Stratix10 SOC
reset: uniphier: add ethernet reset control support
reset: socfpga: fix for 64-bit compilation
ARC: reset: introduce AXS10x reset driver
Add basic support for R-Car V3M (R8A77970) SoC.
Sergei Shtylyov says:
* Add support for R-Car V3M (R8A77970) SoC power areas to the R-Car SYSC
driver
* Add support for identifying the R-Car V3M (R8A77970) SoC
* Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this
driver is needed for the clock driver to work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5yPj
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Pull "Renesas ARM Based SoC Drivers Updates for v4.15" from Simon Horman:
Add basic support for R-Car V3M (R8A77970) SoC.
Sergei Shtylyov says:
* Add support for R-Car V3M (R8A77970) SoC power areas to the R-Car SYSC
driver
* Add support for identifying the R-Car V3M (R8A77970) SoC
* Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this
driver is needed for the clock driver to work
* tag 'renesas-drivers-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: add R8A77970 support
soc: renesas: identify R-Car V3M
soc: renesas: rcar-rst: add R8A77970 support
Add basic reset data for Socionext's new SoC PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ARC AXS10x boards support custom IP-block which allows to control
reset signals of selected peripherals. For example DW GMAC, etc...
This block is controlled via memory-mapped register (AKA CREG) which
represents up-to 32 reset lines. This regiter is self-clearing so we
don't need to deassert line after reset.
As of today only the following lines are used:
- DW GMAC - line 5
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no plan yet to do a v2 board. And even if we were to do it only
some IPs would actually change, so it be best to add suffixes at that
point, not now !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When applying the original patch [1], the DT binding docs were lost.
This patch adds them back.
[1] https://patchwork.kernel.org/patch/9852997/
Fixes: e0be864f14 ("ARC: reset: introduce HSDKv1 reset driver")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this driver
is needed for the clock driver to work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver subsystems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yBzS
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The reset controllers (on xRX200 and newer SoCs have two of them) are
provided by the RCU module. This was initially implemented as a simple
reset controller. However, the RCU module provides more functionality
(ethernet GPHYs, USB PHY, etc.), which makes it a MFD device.
The old reset controller driver implementation from
arch/mips/lantiq/xway/reset.c did not honor this fact.
For some devices the request and the status bits are different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: john@phrozen.org
Cc: kishon@ti.com
Cc: mark.rutland@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- constify zx2967 reset_ops
- add a convenience API to manage an array of resets
- let deassert report success and let assert report success for shared resets
if the reset controller driver does not implement (de)assert.
- add HSDKv1 reset driver
- remove Gemini reset controller, the driver is made obsolete
by a combined clock/reset driver in drivers/clk
- fix the total number of reset lines in the sunxi driver
- various uniphier updates and fixes:
- remove sLD3 SoC support
- simplify system reset register and bit definitions
- add audio systems, video input subsystem, and analog amplifiers reset
controls
-----BEGIN PGP SIGNATURE-----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=YW4N
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.14' of git://git.pengutronix.de/git/pza/linux into next/drivers
Pull "Reset controller changes for v4.14" from Philipp Zabel:
- constify zx2967 reset_ops
- add a convenience API to manage an array of resets
- let deassert report success and let assert report success for shared resets
if the reset controller driver does not implement (de)assert.
- add HSDKv1 reset driver
- remove Gemini reset controller, the driver is made obsolete
by a combined clock/reset driver in drivers/clk
- fix the total number of reset lines in the sunxi driver
- various uniphier updates and fixes:
- remove sLD3 SoC support
- simplify system reset register and bit definitions
- add audio systems, video input subsystem, and analog amplifiers reset
controls
* tag 'reset-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
reset: uniphier: add audio systems reset control
reset: sunxi: fix number of reset lines
reset: uniphier: do not use per-SoC macro for system reset block
reset: uniphier: remove sLD3 SoC support
Revert "reset: Add a Gemini reset controller"
ARC: reset: introduce HSDKv1 reset driver
reset: make (de)assert report success for self-deasserting reset drivers
reset: Add APIs to manage array of resets
reset: zx2967: constify zx2967_reset_ops.
Add a reset line for analog signal amplifier core (ADAMV) on
UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This SoC is too old. It is difficult to maintain any longer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add TI SCI reset controller binding. This describes the DT binding
details for a reset controller node providing reset management services
to hardware blocks (reset consumers) using the Texas Instrument's System
Control Interface (TI SCI) protocol to communicate to a system controller
block present on the SoC.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: revise the binding format]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The LD11 SoC is equipped with not only MIO-reset but also SD-reset
for controlling RST_n pin of the eMMC device.
Update the binding document and remove unneeded "." from each line
in itemization.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fix couple of typos in the example given in the TI syscon reset
binding. The ti,reset-bits used for DSP0 are corrected to match
the values that will be used in the actual DT node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
framework. The only patch that can even be considered "core" adds another
clk_get() variant. The rest of the changes are in drivers for various SoCs, and
we have a few bits for ARM shmobile architecture code (dts and mach) due to the
dependency we're breaking between shmobile architecture code and its clk
driver. Those shmobile bits have also been pulled into arm-soc tree. Here's the
summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that have
subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RXZr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is a fairly quiet release. We don't have any patches to the core
framework. The only patch that can even be considered "core" adds
another clk_get() variant. The rest of the changes are in drivers for
various SoCs, and we have a few bits for ARM shmobile architecture
code (dts and mach) due to the dependency we're breaking between
shmobile architecture code and its clk driver. Those shmobile bits
have also been pulled into arm-soc tree. Here's the summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that
have subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL
support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: bcm: Fix 'maybe-uninitialized' warning in bcm2835_clock_choose_div_and_prate()
clk: add devm_get_clk_from_child() API
clk: st: clk-flexgen: Unmap region obtained by of_iomap
clk: keystone: pll: Unmap region obtained by of_iomap
clk:mmp:clk-of-mmp2: Free memory and Unmap region obtained by kzalloc and of_iomap
clk:mmp:clk-of-pxa910: Free memory and Unmap region obtained by kzmalloc and of_iomap
clk: mmp: clk-of-pxa1928: Free memory obtained by kzalloc
clk: cdce925: Fix limit check
clk: bcm: Make COMMON_CLK_IPROC into a library
clk: qoriq: added ls1012a clock configuration
clk: ti: dra7: fix "failed to lookup clock node gmac_gmii_ref_clk_div" boot message
clk: bcm: Allow rate change propagation to PLLH_AUX on VEC clock
clk: bcm: Support rate change propagation on bcm2835 clocks
clk: bcm2835: Avoid overwriting the div info when disabling a pll_div clk
clk: ti: omap36xx: Work around sprz319 advisory 2.1
clk: clk-wm831x: fix a logic error
clk: uniphier: add cpufreq data for LD11, LD20 SoCs
clk: uniphier: add CPU-gear change (cpufreq) support
clk: qcom: Put venus core0/1 gdscs to hw control mode
clk: qcom: gdsc: Add support for gdscs with HW control
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
Add DT bindings for the Renesas R-Car Reset Controller (R-Car Gen1
RESET/WDT and R-Car Gen2/Gen3 and RZ/G RST).
As the features provided by the hardware module differ a lot across the
various SoC families and members, only SoC-specific compatible values
are defined.
For now we use the RST only for providing access to the state of the
mode pins, which is needed by the clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Add new compatible string for reset and sys-ctrl for the Oxford
Semiconductor OX820 Support.
Drop the OX810SE indices since they moved in a dedicated include file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt softreset bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt softreset bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt powerdown bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <p.zabel@pengutronix.de>
Cc: <robh+dt@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
This is the initial commit for UniPhier reset controller driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This adds documentation of device tree bindings for the
STM32 reset controller.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Add TI syscon reset controller binding. This will hook to the reset
framework and use syscon/regmap to set reset bits. This allows reset
control of individual SoC subsytems and devices with memory-mapped
reset registers in a common register memory space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add compatible for media reset controller.
Actually, there are two reset controllers in hi6220 SoC:
The peripheral reset controller bits are part of sysctrl registers.
The media reset controller bits are part of mediactrl registers.
So for the compatible part, it should contain "syscon" for both peripheral
and media reset controller.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Sebastian pointed out that .../bindings/reset is usually used for
peripheral reset controllers, whereas .../bindings/power/reset is
used for Board/System reset controllers.
Reported-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add DT bindings for the Meson SoC Reset Controller documentation and the
associated include file.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add bindings for the Oxford Semiconductor OXNAS reset controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
The "altr,modrst-offset" property represents the offset into the reset manager
that is the first register to be used by the driver to bring peripherals out
of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Yixun Lan