Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra SPI controller has TX and RX trimmers to tuning the delay of
SPI master clock with respect to the data.
TX and RX tap values are based on the platform validation across the
PVT and the trimmer values vary based on the trace lengths to the
corresponding SPI devices.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch documents set_cs_timing SPI master method.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the dts binding document for Zynq SOC QSPI controller.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.
This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).
This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation to the Synopsys SPI dt-bindings to support an
optional interface clock that may be used for register access.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Synopsys SSI driver uses a mandatory clock that is not documented,
so detail it in the device tree bindings. Also correct the spelling of
"pins" in the "Optional Properties" section for the driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MPC8309 has a dedicated signal, SPISEL_BOOT, usually used as chip
select for the flash device from which the bootloader is loaded. It is
not an ordinary gpio, but is simply controlled via the SPI_CS register
in the system configuration.
To allow accessing such a spi slave, we need to teach
fsl_spi_cs_control() how to control the SPISEL_BOOT signal. To
distinguish the gpio-controlled slaves, continue to have those use
chip_select values of 0..ngpios-1, and use chip_select == ngpios for
the boot flash.
I'm not too happy with all the ifdeffery, but it seems to be necessary
for guarding the sysdev/fsl_soc.h and use of
get_immrbase() (spi-fsl-lib.c already contains similar ifdeffery).
Googling suggests that the MPC8306 is similar, with the SPI_CS
register at the same offset.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Replace the /sys/class/dax device model with /sys/bus/dax, and include
a compat driver so distributions can opt-in to the new ABI.
* Allow for an alternative driver for the device-dax address-range
* Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
* Arrange for the device-dax target-node to be onlined so that the newly
added memory range can be uniquely referenced by numa apis.
-----BEGIN PGP SIGNATURE-----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=hfa3
-----END PGP SIGNATURE-----
Merge tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull device-dax updates from Dan Williams:
"New device-dax infrastructure to allow persistent memory and other
"reserved" / performance differentiated memories, to be assigned to
the core-mm as "System RAM".
Some users want to use persistent memory as additional volatile
memory. They are willing to cope with potential performance
differences, for example between DRAM and 3D Xpoint, and want to use
typical Linux memory management apis rather than a userspace memory
allocator layered over an mmap() of a dax file. The administration
model is to decide how much Persistent Memory (pmem) to use as System
RAM, create a device-dax-mode namespace of that size, and then assign
it to the core-mm. The rationale for device-dax is that it is a
generic memory-mapping driver that can be layered over any "special
purpose" memory, not just pmem. On subsequent boots udev rules can be
used to restore the memory assignment.
One implication of using pmem as RAM is that mlock() no longer keeps
data off persistent media. For this reason it is recommended to enable
NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
at rest. We considered making this recommendation an actively enforced
requirement, but in the end decided to leave it as a distribution /
administrator policy to allow for emulation and test environments that
lack security capable NVDIMMs.
Summary:
- Replace the /sys/class/dax device model with /sys/bus/dax, and
include a compat driver so distributions can opt-in to the new ABI.
- Allow for an alternative driver for the device-dax address-range
- Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
- Arrange for the device-dax target-node to be onlined so that the
newly added memory range can be uniquely referenced by numa apis"
NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.
And apparently the PMEM modules can cause that a lot more than regular
RAM. The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.
Quoting Dan from another email:
"The exposure can be reduced in the volatile-RAM case by scanning for
and clearing errors before it is onlined as RAM. The userspace tooling
for that can be in place before v5.1-final. There's also runtime
notifications of errors via acpi_nfit_uc_error_notify() from
background scrubbers on the DIMM devices. With that mechanism the
kernel could proactively clear newly discovered poison in the volatile
case, but that would be additional development more suitable for v5.2.
I understand the concern, and the need to highlight this issue by
tapping the brakes on feature development, but I don't see PMEM as RAM
making the situation worse when the exposure is also there via DAX in
the PMEM case. Volatile-RAM is arguably a safer use case since it's
possible to repair pages where the persistent case needs active
application coordination"
* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: "Hotplug" persistent memory for use like normal RAM
mm/resource: Let walk_system_ram_range() search child resources
mm/memory-hotplug: Allow memory resources to be children
mm/resource: Move HMM pr_debug() deeper into resource code
mm/resource: Return real error codes from walk failures
device-dax: Add a 'modalias' attribute to DAX 'bus' devices
device-dax: Add a 'target_node' attribute
device-dax: Auto-bind device after successful new_id
acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
device-dax: Add /sys/class/dax backwards compatibility
device-dax: Add support for a dax override driver
device-dax: Move resource pinning+mapping into the common driver
device-dax: Introduce bus + driver model
device-dax: Start defining a dax bus model
device-dax: Remove multi-resource infrastructure
device-dax: Kill dax_region base
device-dax: Kill dax_region ida
-----BEGIN PGP SIGNATURE-----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=qBae
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
-----BEGIN PGP SIGNATURE-----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=dG+z
-----END PGP SIGNATURE-----
Merge tag '5.1-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb3 updates from Steve French:
"Various tracing and debugging improvements, crediting fixes, some
cleanup, and important fallocate fix (fixes three xfstests) and lock
fix.
Summary:
- Various additional dynamic tracing tracepoints
- Debugging improvements (including ability to query the server via
SMB3 fsctl from userspace tools which can help with stats and
debugging)
- One minor performance improvement (root directory inode caching)
- Crediting (SMB3 flow control) fixes
- Some cleanup (docs and to mknod)
- Important fixes: one to smb3 implementation of fallocate zero range
(which fixes three xfstests) and a POSIX lock fix"
* tag '5.1-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6: (22 commits)
CIFS: fix POSIX lock leak and invalid ptr deref
SMB3: Allow SMB3 FSCTL queries to be sent to server from tools
cifs: fix incorrect handling of smb2_set_sparse() return in smb3_simple_falloc
smb2: fix typo in definition of a few error flags
CIFS: make mknod() an smb_version_op
cifs: minor documentation updates
cifs: remove unused value pointed out by Coverity
SMB3: passthru query info doesn't check for SMB3 FSCTL passthru
smb3: add dynamic tracepoints for simple fallocate and zero range
cifs: fix smb3_zero_range so it can expand the file-size when required
cifs: add SMB2_ioctl_init/free helpers to be used with compounding
smb3: Add dynamic trace points for various compounded smb3 ops
cifs: cache FILE_ALL_INFO for the shared root handle
smb3: display volume serial number for shares in /proc/fs/cifs/DebugData
cifs: simplify how we handle credits in compound_send_recv()
smb3: add dynamic tracepoint for timeout waiting for credits
smb3: display security information in /proc/fs/cifs/DebugData more accurately
cifs: add a timeout argument to wait_for_free_credits
cifs: prevent starvation in wait_for_free_credits for multi-credit requests
cifs: wait_for_free_credits() make it possible to wait for >=1 credits
...
for 32-bit guests
s390: interrupt cleanup, introduction of the Guest Information Block,
preparation for processor subfunctions in cpu models
PPC: bug fixes and improvements, especially related to machine checks
and protection keys
x86: many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations; plus AVIC fixes.
Generic: memcg accounting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJci+7XAAoJEL/70l94x66DUMkIAKvEefhceySHYiTpfefjLjIC
16RewgHa+9CO4Oo5iXiWd90fKxtXLXmxDQOS4VGzN0rxvLGRw/fyXIxL1MDOkaAO
l8SLSNuewY4XBUgISL3PMz123r18DAGOuy9mEcYU/IMesYD2F+wy5lJ17HIGq6X2
RpoF1p3qO1jfkPTKOob6Ixd4H5beJNPKpdth7LY3PJaVhDxgouj32fxnLnATVSnN
gENQ10fnt8BCjshRYW6Z2/9bF15JCkUFR1xdBW2/xh1oj+kvPqqqk2bEN1eVQzUy
2hT/XkwtpthqjSbX8NNavWRSFnOnbMLTRKQyIXmFVsM5VoSrwtiGsCFzBgcT++I=
=XIzU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and
other clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups
(from Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from
the arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues
(from Yang Shi and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U6og
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and other
clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups (from
Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from the
arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues (from Yang Shi
and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8849/1: NOMMU: Fix encodings for PMSAv8's PRBAR4/PRLAR4
ARM: 8848/1: virt: Align GIC version check with arm64 counterpart
ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used
ARM: 8845/1: use unified assembler in c files
ARM: 8844/1: use unified assembler in assembly files
ARM: 8843/1: use unified assembler in headers
ARM: 8841/1: use unified assembler in macros
ARM: 8840/1: use a raw_spinlock_t in unwind
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
ARM: 8837/1: coresight: etmv4: Update ID register table to add UCI support
ARM: 8836/1: drivers: amba: Update component matching to use the CoreSight UCI values.
ARM: 8838/1: drivers: amba: Updates to component identification for driver matching.
ARM: 8833/1: Ensure that NEON code always compiles with Clang
ARM: avoid Cortex-A9 livelock on tight dmb loops
ARM: smp: remove arch-provided "pen_release"
ARM: actions: remove boot_lock and pen_release
ARM: oxnas: remove CPU hotplug implementation
ARM: qcom: remove unnecessary boot_lock
ARM: 8832/1: NOMMU: Limit visibility for CONFIG_FLASH_{MEM_BASE,SIZE}
ARM: 8831/1: NOMMU: pmsa-v8: remove unneeded semicolon
...
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+ZFI
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.1' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Just a couple of small fixes and cleanups:
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)"
* tag 'fbdev-v5.1' of git://github.com/bzolnier/linux:
fbdev: mbx: fix a misspelled variable name
fbdev: omap2: fix warnings in dss core
video: fbdev: Fix potential NULL pointer dereference
fbcon: Silence fbcon logo on 'quiet' boots
printk: Export console_printk
ARM: dts: imx28-cfa10036: Fix the reset gpio signal polarity
video: ssd1307fb: Do not hard code active-low reset sequence
dt-bindings: display: ssd1307fb: Remove reset-active-low from examples
fbdev: fbmem: fix memory access if logo is bigger than the screen
video/fbdev: refactor video= cmdline parsing
fbdev: mbx: fix up debugfs file creation
fbdev: omap2: no need to check return value of debugfs_create functions
video: fbdev: geode: remove ifdef OLPC noise
video: offb: annotate implicit fall throughs
omapfb: fix typo
fbdev: Use of_node_name_eq for node name comparisons
fbcon: use kvmalloc() for scrollback buffer
fbdev: chipsfb: remove set but not used variable 'size'
fbdev/via: fix spelling mistake "Expandsion" -> "Expansion"
We've continued mainly to fix bugs in this round, as f2fs has been shipped
in more devices. Especially, we've focused on stabilizing checkpoint=disable
feature, and provided some interfaces for QA.
Enhancement:
- expose FS_NOCOW_FL for pin_file
- run discard jobs at unmount time with timeout
- tune discarding thread to avoid idling which consumes power
- some checking codes to address vulnerabilities
- give random value to i_generation
- shutdown with more flags for QA
Bug fix:
- clean up stale objects when mount is failed along with checkpoint=disable
- fix system being stuck due to wrong count by atomic writes
- handle some corrupted disk cases
- fix a deadlock in f2fs_read_inline_dir
We've also added some minor build errors and clean-up patches.
-----BEGIN PGP SIGNATURE-----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=9BoH
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"We've continued mainly to fix bugs in this round, as f2fs has been
shipped in more devices. Especially, we've focused on stabilizing
checkpoint=disable feature, and provided some interfaces for QA.
Enhancements:
- expose FS_NOCOW_FL for pin_file
- run discard jobs at unmount time with timeout
- tune discarding thread to avoid idling which consumes power
- some checking codes to address vulnerabilities
- give random value to i_generation
- shutdown with more flags for QA
Bug fixes:
- clean up stale objects when mount is failed along with
checkpoint=disable
- fix system being stuck due to wrong count by atomic writes
- handle some corrupted disk cases
- fix a deadlock in f2fs_read_inline_dir
We've also added some minor build error fixes and clean-up patches"
* tag 'f2fs-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (53 commits)
f2fs: set pin_file under CAP_SYS_ADMIN
f2fs: fix to avoid deadlock in f2fs_read_inline_dir()
f2fs: fix to adapt small inline xattr space in __find_inline_xattr()
f2fs: fix to do sanity check with inode.i_inline_xattr_size
f2fs: give some messages for inline_xattr_size
f2fs: don't trigger read IO for beyond EOF page
f2fs: fix to add refcount once page is tagged PG_private
f2fs: remove wrong comment in f2fs_invalidate_page()
f2fs: fix to use kvfree instead of kzfree
f2fs: print more parameters in trace_f2fs_map_blocks
f2fs: trace f2fs_ioc_shutdown
f2fs: fix to avoid deadlock of atomic file operations
f2fs: fix to dirty inode for i_mode recovery
f2fs: give random value to i_generation
f2fs: no need to take page lock in readdir
f2fs: fix to update iostat correctly in IPU path
f2fs: fix encrypted page memory leak
f2fs: make fault injection covering __submit_flush_wait()
f2fs: fix to retry fill_super only if recovery failed
f2fs: silence VM_WARN_ON_ONCE in mempool_alloc
...
The series to add memcg accounting to KVM allocations[1] states:
There are many KVM kernel memory allocations which are tied to the
life of the VM process and should be charged to the VM process's
cgroup.
While it is correct to account KVM kernel allocations to the cgroup of
the process that created the VM, it's technically incorrect to state
that the KVM kernel memory allocations are tied to the life of the VM
process. This is because the VM itself, i.e. struct kvm, is not tied to
the life of the process which created it, rather it is tied to the life
of its associated file descriptor. In other words, kvm_destroy_vm() is
not invoked until fput() decrements its associated file's refcount to
zero. A simple example is to fork() in Qemu and have the child sleep
indefinitely; kvm_destroy_vm() isn't called until Qemu closes its file
descriptor *and* the rogue child is killed.
The allocations are guaranteed to be *accounted* to the process which
created the VM, but only because KVM's per-{VM,vCPU} ioctls reject the
ioctl() with -EIO if kvm->mm != current->mm. I.e. the child can keep
the VM "alive" but can't do anything useful with its reference.
Note that because 'struct kvm' also holds a reference to the mm_struct
of its owner, the above behavior also applies to userspace allocations.
Given that mucking with a VM's file descriptor can lead to subtle and
undesirable behavior, e.g. memcg charges persisting after a VM is shut
down, explicitly document a VM's lifecycle and its impact on the VM's
resources.
Alternatively, KVM could aggressively free resources when the creating
process exits, e.g. via mmu_notifier->release(). However, mmu_notifier
isn't guaranteed to be available, and freeing resources when the creator
exits is likely to be error prone and fragile as KVM would need to
ensure that it only freed resources that are truly out of reach. In
practice, the existing behavior shouldn't be problematic as a properly
configured system will prevent a child process from being moved out of
the appropriate cgroup hierarchy, i.e. prevent hiding the process from
the OOM killer, and will prevent an unprivileged user from being able to
to hold a reference to struct kvm via another method, e.g. debugfs.
[1]https://patchwork.kernel.org/patch/10806707/
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fix a crash caused by unloading an SSDT overlay (Andy Shevchenko).
- Prevent user space from getting confusing error values on failing
ACPI sysfs accesses (Rafael Wysocki).
- Simplify leaf node detection in the PPTT parsing code by using a
new flag defined in ACPI 6.3 (Jeremy Linton).
- Add missing "static" in some places in the ACPI configfs code
(Andy Shevchenko).
- Fix acpidbg tool path in the ACPI documentation (Flavio Suligoi).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mxN+
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These fix a couple of issues and do some cleanups on top of the
previous ACPI changes for 5.1-rc1.
Specifics:
- Fix a crash caused by unloading an SSDT overlay (Andy Shevchenko)
- Prevent user space from getting confusing error values on failing
ACPI sysfs accesses (Rafael Wysocki)
- Simplify leaf node detection in the PPTT parsing code by using a
new flag defined in ACPI 6.3 (Jeremy Linton)
- Add missing "static" in some places in the ACPI configfs code (Andy
Shevchenko)
- Fix acpidbg tool path in the ACPI documentation (Flavio Suligoi)"
* tag 'acpi-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sysfs: Prevent get_status() from returning acpi_status
ACPI / device_sysfs: Avoid OF modalias creation for removed device
ACPI / configfs: Mark local data structures static
ACPI / configfs: Mark local functions static
ACPI: tables: Simplify PPTT leaf node detection
ACPI: Documentation: Fix path for acpidbg tool
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs.
-----BEGIN PGP SIGNATURE-----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=4xC9
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.1' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs"
* tag 'rproc-v5.1' of git://github.com/andersson/remoteproc: (33 commits)
remoteproc: fix for "dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag"
remoteproc: fix rproc_check_carveout_da() returned error and comments
remoteproc: fix trace buffer va initialization
remoteproc: fix rproc_alloc_carveout() for rproc with iommu domain
remoteproc: add warning on resource table cast
remoteproc: fix rproc_alloc_carveout() bad variable cast
remoteproc: fix rproc_da_to_va in case of unallocated carveout
remoteproc: correct rproc_mem_entry_init() comments
remoteproc: fix recovery procedure
rpmsg: virtio: change header file sort style
rpmsg: virtio: allocate buffer from parent
remoteproc: st: add reserved memory support
remoteproc: create vdev subdevice with specific dma memory pool
remoteproc: q6v5_adsp: Remove voting for lpass_aon clock
dt-binding: remoteproc: Remove lpass_aon clock from adsp pil clock list
remoteproc: q6v5-mss: Active powerdomain for SDM845
remoteproc: q6v5-mss: Vote for rpmh power domains
remoteproc: qcom: Add support for parsing fw dt bindings
remoteproc: qcom_q6v5: don't auto boot remote processor
remoteproc: qcom: Wait for shutdown-ack/ind on sysmon shutdown
...
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
The changes for this cycle are across the board. The bulk of it is
cleanups, but there's also new device support in some drivers as well as
more conversions to the atomic API.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAlyJFvUZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zobfREACTyAxr02GyEQFm4wLLV/OG
ynJ45IY2g/9OEY6RGmHQXzcBKycmFtifV6uF5PhMr0KZzdfp/uIMnyHsxV7Gm+ia
NNhG7gQPrb3yZev2AGmc6N/je2+5SL6AZH3+C5ocRqThNKKFknr3uZHbZpmTQlQf
QV63UYNpwtUrFu7jvzNz1kCBBUispXoDY44W0YSv8RYiKOxwJabPott0oOJH8miF
lVyCa2yyA8KuW1DTP13XSHMpmUwKGNkiqaFWGIMPFz6ViK5zj/rY92dUIwLegmh7
l/A7CBMCilw9yd9o1bhSWp2yUJ1gf8QeC64awa0euk9abgX574Nxt+vJsF8EtpaF
8aCcQrJpjlpPCQV4rP62G8Dcr7tWRNmKWKRNMaXQICpdhcLXuwg6tz4HH8z+I1um
W+w+9wsiqrRqKyqxlmQEXBi3qSPepJkU/DUsrE7QoO2jbmi21xyVIi1AQHXqNZYo
y2NzAADuh4i7L8AVFtJ1KcvdZZIBF/XrQXgXEgjX6fQpcs6aMyNOHTu9Xod7XW59
8yBKKqYmvSmmxDcFFfajkBuUbIuUqIzFxr4U6JYHQsWNnVN1ey+MSlZK6bHA8gw0
UngjRNv8fEAU0Hck2Z0iwDe1zHVW6g/ZNKZC2TUqzETPvZHg9QKt0sJYGkmxoR5O
JW1eTekpW57XahV2oX7f3g==
=TyJJ
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this cycle are across the board.
The bulk of it is cleanups, but there's also new device support in
some drivers as well as more conversions to the atomic API"
* tag 'pwm/for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: atmel: Remove useless symbolic definitions
pwm: bcm-kona: Update macros to remove braces around numbers
pwm: imx27: Only enable the clocks once in .get_state()
pwm: rcar: Improve calculation of divider
pwm: rcar: Remove legacy APIs
pwm: rcar: Use "atomic" API on rcar_pwm_resume()
pwm: rcar: Add support "atomic" API
pwm: atmel: Add support for SAM9X60's PWM controller
pwm: atmel: Add PWM binding for SAM9X60
pwm: atmel: Rename objects of type atmel_pwm_data
pwm: atmel: Add support for controllers with 32 bit counters
pwm: atmel: Add struct atmel_pwm_data
pwm: Add MediaTek MT8183 display PWM driver support
pwm: hibvt: Add hi3559v100 support
dt-bindings: pwm: hibvt: Add hi3559v100 support
pwm: hibvt: Use individual struct per of-data
pwm: imx: Signedness bug in imx_pwm_get_state()
pwm: imx: Split into two drivers
pwm: imx: Don't print an error on -EPROBE_DEFER
pwm: imx: Set driver data earlier simplifying the end of ->probe()
...
users to more easily find the jbd2 journal thread for a particular
ext4 file system.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlx8utQACgkQ8vlZVpUN
gaOMOQf+Olp6hTbCuPJNill7npEejkPu9VhNvLPp3dLPBfsyqG9IOZmUaKKtr3LS
ZYYzMMoIlbHDsWM70O92zDS3s1ThKRFoDdcw4YKXkn1Awlqc4LRZ/NnzyIIdA3mK
rhOvcr6ttWk2B2S67nGceTH08SX5zACMtMiQijP58+GCp4Xe+PdqPRRjYYJSOZMv
xCS43LoWY0tkeBTQuk9WYTi6G/E1X/aiq06pYiQzP69PotN6/cFSdNgP1r+7dYiS
V4IXPqEqFt8NvUZb1bJchT3+2zM3Xi/+n//7yLkpY7OhX6p1p24oB7abMstp3ssU
BlF8KP4elQcI892QX2Hf+0r4tBu+0w==
=2yLu
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"A large number of bug fixes and cleanups.
One new feature to allow users to more easily find the jbd2 journal
thread for a particular ext4 file system"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
jbd2: jbd2_get_transaction does not need to return a value
jbd2: fix invalid descriptor block checksum
ext4: fix bigalloc cluster freeing when hole punching under load
ext4: add sysfs attr /sys/fs/ext4/<disk>/journal_task
ext4: Change debugging support help prefix from EXT4 to Ext4
ext4: fix compile error when using BUFFER_TRACE
jbd2: fix compile warning when using JBUFFER_TRACE
ext4: fix some error pointer dereferences
ext4: annotate more implicit fall throughs
ext4: annotate implicit fall throughs
ext4: don't update s_rev_level if not required
jbd2: fold jbd2_superblock_csum_{verify,set} into their callers
jbd2: fix race when writing superblock
ext4: fix crash during online resizing
ext4: disallow files with EXT4_JOURNAL_DATA_FL from EXT4_IOC_SWAP_BOOT
ext4: add mask of ext4 flags to swap
ext4: update quota information while swapping boot loader inode
ext4: cleanup pagecache before swap i_data
ext4: fix check of inode in swap_inode_boot_loader
ext4: unlock unused_pages timely when doing writeback
...
- rbd will now ignore discards that aren't aligned and big enough to
actually free up some space (myself). This is controlled by the new
alloc_size map option and can be disabled if needed.
- support for rbd deep-flatten feature (myself). Deep-flatten allows
"rbd flatten" to fully disconnect the clone image and its snapshots
from the parent and make the parent snapshot removable.
- a new round of cap handling improvements (Zheng Yan). The kernel
client should now be much more prompt about releasing its caps and
it is possible to put a limit on the number of caps held.
- support for getting ceph.dir.pin extended attribute (Zheng Yan)
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlyH5LUTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi9cCCACb8PiX+PZWuwboAmO66TIQGT8VgEer
/K3zU6UsmnKHldk/gyjK+ESIxX64zP9HrNGTDxlDKZTB52GDiAYbhcBnskMtrtgl
EFLweTRs6XiHI1yV3qmElyPz0eLnWBXLUW6RDoyHxGUPWuGk9Mp4Of+PSkl2aO/9
j4eBQj7FYB6XAuzwFKltFq3uKb+jODDrW7VRDDTMEYGPHZOU6EXXUEUOrAtAreiU
j9wHF2AZ61WdVjzzXF/tBHJIwGGZj8102Af4ra/UMuHmtGZag6n0eY6uzGXluY2o
uGPuhFHMExsqjhCCPHtayWJW7WG0pQKKuwT8Ucw/KPBJ6Ok3Z2tG27/8
=sQNQ
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.1-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"The highlights are:
- rbd will now ignore discards that aren't aligned and big enough to
actually free up some space (myself). This is controlled by the new
alloc_size map option and can be disabled if needed.
- support for rbd deep-flatten feature (myself). Deep-flatten allows
"rbd flatten" to fully disconnect the clone image and its snapshots
from the parent and make the parent snapshot removable.
- a new round of cap handling improvements (Zheng Yan). The kernel
client should now be much more prompt about releasing its caps and
it is possible to put a limit on the number of caps held.
- support for getting ceph.dir.pin extended attribute (Zheng Yan)"
* tag 'ceph-for-5.1-rc1' of git://github.com/ceph/ceph-client: (26 commits)
Documentation: modern versions of ceph are not backed by btrfs
rbd: advertise support for RBD_FEATURE_DEEP_FLATTEN
rbd: whole-object write and zeroout should copyup when snapshots exist
rbd: copyup with an empty snapshot context (aka deep-copyup)
rbd: introduce rbd_obj_issue_copyup_ops()
rbd: stop copying num_osd_ops in rbd_obj_issue_copyup()
rbd: factor out __rbd_osd_req_create()
rbd: clear ->xferred on error from rbd_obj_issue_copyup()
rbd: remove experimental designation from kernel layering
ceph: add mount option to limit caps count
ceph: periodically trim stale dentries
ceph: delete stale dentry when last reference is dropped
ceph: remove dentry_lru file from debugfs
ceph: touch existing cap when handling reply
ceph: pass inclusive lend parameter to filemap_write_and_wait_range()
rbd: round off and ignore discards that are too small
rbd: handle DISCARD and WRITE_ZEROES separately
rbd: get rid of obj_req->obj_request_count
libceph: use struct_size() for kmalloc() in crush_decode()
ceph: send cap releases more aggressively
...
Pull vfs mount infrastructure updates from Al Viro:
"The rest of core infrastructure; no new syscalls in that pile, but the
old parts are switched to new infrastructure. At that point
conversions of individual filesystems can happen independently; some
are done here (afs, cgroup, procfs, etc.), there's also a large series
outside of that pile dealing with NFS (quite a bit of option-parsing
stuff is getting used there - it's one of the most convoluted
filesystems in terms of mount-related logics), but NFS bits are the
next cycle fodder.
It got seriously simplified since the last cycle; documentation is
probably the weakest bit at the moment - I considered dropping the
commit introducing Documentation/filesystems/mount_api.txt (cutting
the size increase by quarter ;-), but decided that it would be better
to fix it up after -rc1 instead.
That pile allows to do followup work in independent branches, which
should make life much easier for the next cycle. fs/super.c size
increase is unpleasant; there's a followup series that allows to
shrink it considerably, but I decided to leave that until the next
cycle"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (41 commits)
afs: Use fs_context to pass parameters over automount
afs: Add fs_context support
vfs: Add some logging to the core users of the fs_context log
vfs: Implement logging through fs_context
vfs: Provide documentation for new mount API
vfs: Remove kern_mount_data()
hugetlbfs: Convert to fs_context
cpuset: Use fs_context
kernfs, sysfs, cgroup, intel_rdt: Support fs_context
cgroup: store a reference to cgroup_ns into cgroup_fs_context
cgroup1_get_tree(): separate "get cgroup_root to use" into a separate helper
cgroup_do_mount(): massage calling conventions
cgroup: stash cgroup_root reference into cgroup_fs_context
cgroup2: switch to option-by-option parsing
cgroup1: switch to option-by-option parsing
cgroup: take options parsing into ->parse_monolithic()
cgroup: fold cgroup1_mount() into cgroup1_get_tree()
cgroup: start switching to fs_context
ipc: Convert mqueue fs to fs_context
proc: Add fs_context support to procfs
...
Merge misc updates from Andrew Morton:
- a few misc things
- the rest of MM
- remove flex_arrays, replace with new simple radix-tree implementation
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (38 commits)
Drop flex_arrays
sctp: convert to genradix
proc: commit to genradix
generic radix trees
selinux: convert to kvmalloc
md: convert to kvmalloc
openvswitch: convert to kvmalloc
of: fix kmemleak crash caused by imbalance in early memory reservation
mm: memblock: update comments and kernel-doc
memblock: split checks whether a region should be skipped to a helper function
memblock: remove memblock_{set,clear}_region_flags
memblock: drop memblock_alloc_*_nopanic() variants
memblock: memblock_alloc_try_nid: don't panic
treewide: add checks for the return value of memblock_alloc*()
swiotlb: add checks for the return value of memblock_alloc*()
init/main: add checks for the return value of memblock_alloc*()
mm/percpu: add checks for the return value of memblock_alloc*()
sparc: add checks for the return value of memblock_alloc*()
ia64: add checks for the return value of memblock_alloc*()
arch: don't memset(0) memory returned by memblock_alloc()
...
When the Partial Parity Log is enabled, circular buffer is used to store
PPL data. Each write to RAID device causes overwrite of data in this buffer
so some write_hint can be set to those request to help drives handle
garbage collection. This patch adds new sysfs attribute which can be used
to specify which write_hint should be assigned to PPL.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
All existing users have been converted to generic radix trees
Link: http://lkml.kernel.org/r/20181217131929.11727-8-kent.overstreet@gmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Very simple radix tree implementation that supports storing arbitrary
size entries, up to PAGE_SIZE - upcoming patches will convert existing
flex_array users to genradixes. The new genradix code has a much
simpler API and implementation, and doesn't have a hard limit on the
number of elements like flex_array does.
Link: http://lkml.kernel.org/r/20181217131929.11727-5-kent.overstreet@gmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. SPDX identifier cleanup for platform/chrome
2. Cleanup series between mfd and chrome/platform, moving
cros-ec attributes from mfd/cros_ec_dev to sub-drivers in platform/chrome.
3. Wilco EC driver
4. Maintainership change to new group repository.
-----BEGIN PGP SIGNATURE-----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=2nC0
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
- SPDX identifier cleanup for platform/chrome
- Cleanup series between mfd and chrome/platform, moving cros-ec
attributes from mfd/cros_ec_dev to sub-drivers in platform/chrome
- Wilco EC driver
- Maintainership change to new group repository
* tag 'tag-chrome-platform-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: fix wilco-ec dependencies
platform/chrome: wilco_ec: Add RTC driver
platform/chrome: wilco_ec: Add support for raw commands in debugfs
platform/chrome: Add new driver for Wilco EC
platform/chrome: cros_ec: Remove cros_ec dependency in lpc_mec
MAINTAINERS: chrome-platform: change the git tree to a chrome-platform group git tree
platform/chrome: cros_ec_sysfs: remove pr_fmt() define
platform/chrome: cros_ec_lightbar: remove pr_fmt() define
platform/chrome: cros_kbd_led_backlight: switch to SPDX identifier
platform/chrome: cros_ec_spi: switch to SPDX identifier
platform/chrome: cros_ec_proto: switch to SPDX identifier
platform/chrome: cros_ec_lpc: switch to SPDX identifier
platform/chrome: cros_ec_i2c: switch to SPDX identifier
platform/chrome: cros_ec_vbc: switch to SPDX identifier
platform/chrome: cros_ec_sysfs: switch to SPDX identifier
platform/chrome: cros_ec_lightbar: switch to SPDX identifier
platform/chrome: cros_ec_debugfs: switch to SPDX identifier
platform/chrome: cromeos_pstore: switch to SPDX identifier
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAlyHF2oUHHdpbGx5QGlu
ZnJhZGVhZC5vcmcACgkQDpNsjXcpgj5j9AgAlpeptRfnPO0+VXj+EbxaOOI8tOG+
w+vBasWoQB+lZ9ctf1qUQVSeLn0ErxTM7BaIP7plfDrEWiIbRWkV18B+heS5d1Yz
aTV1d/8tG6/eo61K2VqXHbUhymgMtbXDsg1rwWTF8+Q4xIcMqfYAR0f9ptU1Oejc
pNAn16dYgKi6+4eluY7gXxruBosQ6yNml6iEje9A3uR8nhzTI/P3Yf2GGIZnQLsL
+UIx4Ps38dJ3VCYBPfbnszZfYPpILUH9/Bdx+mAMUtZwvpM3JYqc8XsiFfqDO7n1
3003yUytnRkb1UK3QIvkbPt0G8UOI4s9fxRPsA8lLSww/f2y1r5kC4Mxbg==
=HSP/
-----END PGP SIGNATURE-----
Merge tag 'xarray-5.1-rc1' of git://git.infradead.org/users/willy/linux-dax
Pull XArray updates from Matthew Wilcox:
"This pull request changes the xa_alloc() API. I'm only aware of one
subsystem that has started trying to use it, and we agree on the fixup
as part of the merge.
The xa_insert() error code also changed to match xa_alloc() (EEXIST to
EBUSY), and I added xa_alloc_cyclic(). Beyond that, the usual
bugfixes, optimisations and tweaking.
I now have a git tree with all users of the radix tree and IDR
converted over to the XArray that I'll be feeding to maintainers over
the next few weeks"
* tag 'xarray-5.1-rc1' of git://git.infradead.org/users/willy/linux-dax:
XArray: Fix xa_reserve for 2-byte aligned entries
XArray: Fix xa_erase of 2-byte aligned entries
XArray: Use xa_cmpxchg to implement xa_reserve
XArray: Fix xa_release in allocating arrays
XArray: Mark xa_insert and xa_reserve as must_check
XArray: Add cyclic allocation
XArray: Redesign xa_alloc API
XArray: Add support for 1s-based allocation
XArray: Change xa_insert to return -EBUSY
XArray: Update xa_erase family descriptions
XArray tests: RCU lock prohibits GFP_KERNEL
- Add "onchange(var)" histogram handler that executes a action when $var
changes.
- Add new "snapshot()" action for histogram handlers, that causes a
snapshot of the ring buffer when triggered.
ie. onchange(var).snapshot() will trigger a snapshot if var changes.
- Add alternative for "trace()" action.
Currently, to trigger a synthetic event, the name of that event is used
as the handler name, which is inconsistent with the other actions.
onchange(var).synthetic(param) where it can now be
onchange(var).trace(synthetic, param). The older method will still be
allowed, as long as the synthetic events do not overlap with other
handler names.
- The histogram documentation at testcases were updated for the new
changes.
Added a quicker way to enable set_ftrace_filter files, that will make
it much quicker to bisect tracing a function that shouldn't be traced and
crashes the kernel. (You can echo in numbers to set_ftrace_filter, and it
will select the corresponding function that is in
available_filter_functions).
Some better displaying of the tracing data (and more information was added).
The rest are small fixes and more clean ups to the code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXIXXjRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qrSJAQCbGXAvZE+shfKRhbU1cu1C1nwRMHhH
eeRecJs1RChGFgD/TwatD4FzARQPjfk7snQD5KWPpoRc9grUACC2cZcaWwQ=
=LVBI
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The biggest change for this release is in the histogram code:
- Add "onchange(var)" histogram handler that executes a action when
$var changes.
- Add new "snapshot()" action for histogram handlers, that causes a
snapshot of the ring buffer when triggered. ie.
onchange(var).snapshot() will trigger a snapshot if var changes.
- Add alternative for "trace()" action. Currently, to trigger a
synthetic event, the name of that event is used as the handler
name, which is inconsistent with the other actions.
onchange(var).synthetic(param) where it can now be
onchange(var).trace(synthetic, param). The older method will still
be allowed, as long as the synthetic events do not overlap with
other handler names.
- The histogram documentation at testcases were updated for the new
changes.
Outside of the histogram code, we have:
- Added a quicker way to enable set_ftrace_filter files, that will
make it much quicker to bisect tracing a function that shouldn't be
traced and crashes the kernel. (You can echo in numbers to
set_ftrace_filter, and it will select the corresponding function
that is in available_filter_functions).
- Some better displaying of the tracing data (and more information
was added).
The rest are small fixes and more clean ups to the code"
* tag 'trace-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (37 commits)
tracing: Use strncpy instead of memcpy when copying comm in trace.c
tracing: Use strncpy instead of memcpy when copying comm for hist triggers
tracing: Use strncpy instead of memcpy for string keys in hist triggers
tracing: Use str_has_prefix() in synth_event_create()
x86/ftrace: Fix warning and considate ftrace_jmp_replace() and ftrace_call_replace()
tracing/perf: Use strndup_user() instead of buggy open-coded version
doc: trace: Fix documentation for uprobe_profile
tracing: Fix spelling mistake: "analagous" -> "analogous"
tracing: Comment why cond_snapshot is checked outside of max_lock protection
tracing: Add hist trigger action 'expected fail' test case
tracing: Add alternative synthetic event trace action test case
tracing: Add hist trigger onchange() handler test case
tracing: Add hist trigger snapshot() action test case
tracing: Add SPDX license GPL-2.0 license identifier to inter-event testcases
tracing: Add alternative synthetic event trace action syntax
tracing: Add hist trigger onchange() handler Documentation
tracing: Add hist trigger onchange() handler
tracing: Add hist trigger snapshot() action Documentation
tracing: Add hist trigger snapshot() action
tracing: Add conditional snapshot
...
Add documentation for a new optional property local-mac-address which
is described in ethernet.txt.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
Pull networking fixes from David Miller:
"First batch of fixes in the new merge window:
1) Double dst_cache free in act_tunnel_key, from Wenxu.
2) Avoid NULL deref in IN_DEV_MFORWARD() by failing early in the
ip_route_input_rcu() path, from Paolo Abeni.
3) Fix appletalk compile regression, from Arnd Bergmann.
4) If SLAB objects reach the TCP sendpage method we are in serious
trouble, so put a debugging check there. From Vasily Averin.
5) Memory leak in hsr layer, from Mao Wenan.
6) Only test GSO type on GSO packets, from Willem de Bruijn.
7) Fix crash in xsk_diag_put_umem(), from Eric Dumazet.
8) Fix VNIC mailbox length in nfp, from Dirk van der Merwe.
9) Fix race in ipv4 route exception handling, from Xin Long.
10) Missing DMA memory barrier in hns3 driver, from Jian Shen.
11) Use after free in __tcf_chain_put(), from Vlad Buslov.
12) Handle inet_csk_reqsk_queue_add() failures, from Guillaume Nault.
13) Return value correction when ip_mc_may_pull() fails, from Eric
Dumazet.
14) Use after free in x25_device_event(), also from Eric"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
gro_cells: make sure device is up in gro_cells_receive()
vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()
net/x25: fix use-after-free in x25_device_event()
isdn: mISDNinfineon: fix potential NULL pointer dereference
net: hns3: fix to stop multiple HNS reset due to the AER changes
ip: fix ip_mc_may_pull() return value
net: keep refcount warning in reqsk_free()
net: stmmac: Avoid one more sometimes uninitialized Clang warning
net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
rxrpc: Fix client call queueing, waiting for channel
tcp: handle inet_csk_reqsk_queue_add() failures
net: ethernet: sun: Zero initialize class in default case in niu_add_ethtool_tcam_entry
8139too : Add support for U.S. Robotics USR997901A 10/100 Cardbus NIC
fou, fou6: avoid uninit-value in gue_err() and gue6_err()
net: sched: fix potential use-after-free in __tcf_chain_put()
vhost: silence an unused-variable warning
vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock
connector: fix unsafe usage of ->real_parent
vxlan: do not need BH again in vxlan_cleanup()
net: hns3: add dma_rmb() for rx description
...
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
Pull watchdog core update from Thomas Gleixner:
"A single commit adding a command line parameter which allows to set
the watchdog threshold on the kernel command-line, so kernels with
massive debug facilities enabled won't trigger the watchdog during
early boot and before the threshold can be changed via sysctl"
* 'core-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog/core: Add watchdog_thresh command line parameter
Use MODULE_DEVICE_TABLE across several wmi drivers, keeping
wmi_device_id and MODULE_ALIAS() declarations in sync. Add several
Ideapad models to the no_hw_rfkill list. Add support for new Mellanox
platforms, including new fan and LED functionality. Address Dell
keyboard backlight change event and power button release issues. Update
dell_rbu to use appropriate memory allocation mechanisms. Several small
fixes and Ice Lake support for intel_pmc_core. Fix a suspend regression
for Cherry Trail based devices in intel_int0002_vgpio. A few other
routine fixes.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for BSG2150 ACPI nodes
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
- Correct mlxreg-io KernelVersion for 5.0
MAINTAINERS:
- Include mlxreg.h in Mellanox Platform Driver files
asus-wmi:
- Allow loading on systems without the Asus Management GUID
dell-smbios-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
dell-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
- Ignore new keyboard backlight change event
dell-wmi-descriptor:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
dell_rbu:
- fix lock imbalance in img_update_realloc
- stop abusing the DMA API
huawei-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
ideapad-laptop:
- Add ideapad 330-15ICH to no_hw_rfkill
- Add S130-14IGM to no_hw_rfkill list
- Add Ideapad 530S-14ARR to no_hw_rfkill list
- Add Yoga C930 to no_hw_rfkill_list
- Add Y530-I5ICH-1060 to no_hw_rfkill list
- Fix no_hw_rfkill_list for Lenovo RESCUER R720-15IKBN
intel-hid:
- Missing power button release on some Dell models
intel-wmi-thunderbolt:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
intel_int0002_vgpio:
- Only implement irq_set_wake on Bay Trail
intel_pmc_core:
- Quirk to ignore XTAL shutdown
- Add Package cstates residency info
- Add ICL platform support
- Convert to INTEL_CPU_FAM6 macro
- Avoid a u32 overflow
- Include Reserved IP for LTR
- Fix file permissions for ltr_show
- Fix PCH IP name
- Fix PCH IP sts reading
- Handle CFL regmap properly
leds:
- mlxreg: Add support for capability register
mlx-platform:
- Fix access mode for fan_dir attribute
- Add UID LED for the next generation systems
- Add extra CPLD for next generation systems
- Add support for new VMOD0007 board name
- Add support for fan capability registers
- Add support for fan direction register
modpost:
- file2alias: define size of alias
platform/mellanox:
- mlxreg-hotplug: Fix KASAN warning
platform_data/mlxreg:
- Add capability field to core platform data
- Document fixes for core platform data
touchscreen_dmi:
- Add info for the CHUWI Hi10 Air tablet
- Add info for the Chuwi Hi8 Air tablet
- Add info for the PoV Wintab P1006w (v1.0) tablet
wmi:
- add WMI support to MODULE_DEVICE_TABLE()
- move struct wmi_device_id to mod_devicetable.h
- fix potential null pointer dereference
wmi-bmof:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
x86/CPU:
- Add Icelake model number
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9M1dh6j+oEL41EZIXFIlAfdBhuEFAlyCu1EACgkQXFIlAfdB
huFASAf/d0Y6uqhLD3G7cL2kXjOWoTE9ouWUwv19bBpnohGmD3OMMap4y1lb6nRR
thCJRhpmX4ObS2adAC4otiOxTzmVoYGsuS9kfBwhKIby2VYHCCxxaTUs6bzMdOfV
GsbaMA+vfb29bU4DcWlRtYZIz2FC5oyjW4ZmcMA6KtuBGjG9K1fG5zANQe4H8I0e
zCdcrXhpDGIBJgaJR2N42EUCJruPoEXYfHa1G4B/QKvuW0CXHAdSE0YrN4ju+S3e
Ew9ZXhoxRaqlu+ZB7H5Kyy6Mg3ZGMzbeYyQFLk5f2yiKSTFNiqwTEJl1aE2JSpy3
g8Im+6E44/4G8QOL40g5XwmrxHw5mA==
=Bx4o
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- use MODULE_DEVICE_TABLE across several wmi drivers, keeping
wmi_device_id and MODULE_ALIAS() declarations in sync
- add several Ideapad models to the no_hw_rfkill list
- add support for new Mellanox platforms, including new fan and LED
functionality
- address Dell keyboard backlight change event and power button release
issues
- update dell_rbu to use appropriate memory allocation mechanisms
- several small fixes and Ice Lake support for intel_pmc_core
- fix a suspend regression for Cherry Trail based devices in
intel_int0002_vgpio
- a few other routine fixes
* tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86: (50 commits)
MAINTAINERS: Include mlxreg.h in Mellanox Platform Driver files
platform/x86: ideapad-laptop: Add S130-14IGM to no_hw_rfkill list
platform/x86: mlx-platform: Fix access mode for fan_dir attribute
platform/x86: mlx-platform: Add UID LED for the next generation systems
platform/x86: mlx-platform: Add extra CPLD for next generation systems
platform/x86: wmi-bmof: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: intel-wmi-thunderbolt: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: huawei-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi-descriptor: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-smbios-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: wmi: add WMI support to MODULE_DEVICE_TABLE()
platform/x86: wmi: move struct wmi_device_id to mod_devicetable.h
modpost: file2alias: define size of alias
platform/x86: touchscreen_dmi: Add info for the CHUWI Hi10 Air tablet
platform/x86: ideapad-laptop: Add Ideapad 530S-14ARR to no_hw_rfkill list
platform/x86: ideapad-laptop: Add Yoga C930 to no_hw_rfkill_list
platform/x86: intel_pmc_core: Quirk to ignore XTAL shutdown
platform/x86: intel_pmc_core: Add Package cstates residency info
platform/x86: intel_pmc_core: Add ICL platform support
...
Cao Van Dong