Add a MODULE_DEVICE_TABLE call for OF match tables. This allows the
module to be autoloaded based on devicetree information.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 249751f223 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c9e ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.
The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.
The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().
But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.
Fixes: f1ddc24c9e ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops")
Cc: stable@vger.kernel.org # v3.13+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12be2 ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.
These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.
As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.
Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.
Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().
Fixes: 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
Fixes: 3063a12be2 ("usb: musb: fix PHY power on/off")
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This has the added advantages of being able to enable/disable each
of the channels as simply as enabling/disabling the DT node.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes a possible timeout in poll loop without actually
checking the register before return. In theory the there is a possibility
of loop being scheduled after a long lock/delay, which would then force
the loop to exit without actually checking the register.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Fixed of_phy_provider_lookup to return 'phy_provider' if _of_phy_get
passes the node pointer of the sub-node of phy provider node. This is
needed when phy provider implements multiple PHYs and each PHY is
modelled as the sub-node of PHY provider device node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The Berlin SoC has a two SATA ports. Add a PHY driver to handle them.
The mode selection can let us think this PHY can be configured to fit
other purposes. But there are reasons to think the SATA mode will be
the only one usable: the PHY registers are only accessible indirectly
through two registers in the SATA range, the PHY seems to be integrated
and no information tells us the contrary. For these reasons, make the
driver a SATA PHY driver.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when these SoCs are built
as part of mach-mvebv.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.
This patch is a forward port from Qualcomm's v3.4 andriod kernel.
Tested on IFC6410 board.
CC: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB DWC3 driver on Exynos platform does not work without its
corresponding phy driver. Hence make the PHY driver depend on
Exynos DWC3 driver and default it to yes to make things easier
for the end user.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the USB 2.0 PHYs are required with EHCI/OHCI USB drivers and
USB gadget controller supported by the DWC2 gadget driver, make it
depend on them and default to ARCH_EXYNOS as they are meant for
Exynos platforms. Also, make the sub-drivers silent options enabling
them based on the SoC platforms that they are meant to work with. This
will make life easier for end users who do not have any way knowing the
dependencies.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
The Exynos4412 USB 2.0 PHY hardware differs from the description provided
in the documentation. Some register bits have different function. This
patch fixes the defines of register bits and changes the way how phys are
powered on and off.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make local functions static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.
This also adds proper bindings for miphys.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnZAACgkQMUfUDdst+ynTkACgwma2Ccj7DJl3g1zFEtM0h8ki
8RYAnirwiO0p1B7gIKlDIgGs25JIwN61
=tNZ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.
This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.
Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When NO_IOMEM is enabled (e.g. score architecture), some drivers which
need HAS_IOMEM need notice about it, or it will report related warning:
warning: (GPIO_SCH && GPIO_ICH && GPIO_VX855 && GPIO_RDC321X && IE6XX_WDT && RADIO_WL1273 && HID_SENSOR_HUB && MFD_NVEC) selects MFD_CORE which has unmet direct dependencies (HAS_IOMEM)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB phy controller in the A31 differs mostly from the older controllers
because it has a clock dedicated for each phy, while the older ones were having
a single clock for all the phys.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the phy initialization and variables declaration to the loop itself, since
it is where it really belongs. Also remove all the temporary variables, we can
use the structure members directly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding support to enable/disable VBUS controlled by a
regulator, to enable vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
All other phy drivers use 'select', while this one is
the only one to use 'depends on'. This is not a bug, just
slightly inconsistent, so let's change it to do things the
same way as everyone else.
We may also want to turn GENERIC_PHY into a silent option
that only ever gets turned on if another driver needs it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Matt Porter <mporter@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phys array is of size EXYNOS_MIPI_PHYS_NUM. Trying to access the
index EXYNOS_MIPI_PHYS_NUM should return an error.
Fixes: 069d2e26e9 "phy: Add driver for Exynos MIPI CSIS/DSIM DPHYs"
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If the license string doesn't match exactly, the module refuses to load.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As clocks might be named differently on multiple platforms, use a generic
name in the driver and allow device tree node to specify the platform
specific clock name.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When OMAP_CONTROL_USB was renamed to OMAP_CONTROL_PHY (commit
14da699b), its dependencies were lost in the process. Nothing in the
commit message indicates that this removal was intentional, so I think
it was by accident and the dependencies should be restored.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
- reset
- re-use qnap-poweroff driver for Synology NASs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j/ZI
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu into next/drivers
Merge "mvebu drivers for v3.15" from Jason Cooper:
pull request #1:
- mvebu mbus
- use of_find_matching_node_and_match
- rtc
- use PTR_ERR_OR_ZERO in isl12057
- work around issue in mv where date returned is 2038
- kirkwood -> mach-mvebu
- various Kconfig oneliners to allow building kirkwood in -mvebu/
pull request #2:
- reset
- re-use qnap-poweroff driver for Synology NASs
* tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu:
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
drivers: Enable building of Kirkwood drivers for mach-mvebu
rtc: mv: reset date if after year 2038
rtc: isl12057: use PTR_ERR_OR_ZERO to fix coccinelle warnings
bus: mvebu-mbus: make use of of_find_matching_node_and_match
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The OMAP_USB2 and OMAP_PIPE3 PHY devices will not be
detected if the OMAP_OCP2SCP bus driver is not present.
Make them depend on it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Due to Errata i783, SATA breaks if its DPLL is idled. The recommeded
workaround to issue a softreset to the SATA controller doesn't seem to
work. Here we just prevent SATA DPLL from Idling and hence avoid
the issue altogether.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Limit .power_on() and .power_off() to just control the
PHY power and not the DPLL. The DPLL will be enabled
in .init() and idled in .exit().
Don't reprogram the DPLL if it has been already locked
by the bootloader. This fixes a problem with SATA, where
it fails if SATA was used by the bootloader.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SATA PHY doesn't need 'wkupclk; and 'refclk' so don't
try to get them for SATA PHY.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As this driver is no longer USB specific, use generic clock names.
- Fix PLL_SD_SHIFT from 9 to 10
- Don't separate prepare/unprepare clock from enable/disable. This
ensures optimal power savings.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Add a new compatible for OMAP5 since it does not use any of the
OTG operations as of now.
HAS_SRP and SET_VBUS functionalities are used only for OMAP4.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable the dra7x errata workaround for false disconnect problem
with USB2PHY. False disconnects were detected with some of the devices.
Reduce the sensitivity of the disconnect logic within the USB2PHY subsystem
to enusre these false disconnects are not registered.
[george.cherian@ti.com]
While at that, pass proper flags for each SoC's. This is a common driver
used across OMAP4,OMAP5,DRA7xx and AM437x USB2PHY.
False disconnect workaround is currently applicable for only DRA7x.
Signed-off-by: Austin Beam <austinbeam@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adapt phy-omap-usb2 driver for AM437x.
- Add new comaptible "ti,am437x-usb2" for AM437x
- Pass proper data to differentiate AM437x and others.
- AM437x doesnot support set_vbus and start_srp.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for Exynos 5250. This driver is to replace the old
USB 2.0 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic
PHY framework. The driver includes support for the Exynos 4x10 and 4x12
SoC families.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding devm_of_phy_get will allow to get phys by supplying a
pointer to the struct device_node instead of struct device.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Previously the of_phy_get function took a struct device * and
was declared static. It was impossible to call it from
another driver and thus it was impossible to get phy defined
for a given node. The old function was renamed to _of_phy_get
and was left for internal use. of_phy_get function was added
and it was exported. The function enables to get a phy for
a given device tree node.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that omap-usb2 is adapted to the new generic PHY framework,
*set_suspend* ops can be removed from omap-usb2 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DT-enabled Dove will move over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The Allwinner A1x / A2x SoCs have 2 or 3 usb phys which are all accessed
through a single set of registers. Besides this there are also some other
phy related bits which need poking, which are per phy, but shared between the
ohci and ehci controllers, so these are also controlled from this new phy
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds the SATA PHY driver for Exynos5250.This driver uses the
generic PHY framework to deal with SATA PHY.Exynos5250 SATA PHY comprises
of CMU and TRSV blocks which are of I2C register Map.So this driver
configures the CMU and TRSV block of exynos5250 SATA PHY using i2c.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of requiring user to figure out when PHY_EXYNOS_DP_VIDEO needs
to be selected select it by default for Exynos SoCs. Also enable it
when COMPILE_TEST is selected. If required the display port PHY driver
can be then disabled or compiled in as module.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of requiring user to figure out when PHY_EXYNOS_MIPI_VIDEO needs
to be selected select it by default for Exynos SoCs. Also enable it when
COMPILE_TEST is selected. If required the MIPI CSIS/DPHY driver can be
then disabled or compiled in as module.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Semicolon after switch statement is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Silences the following warnings:
WARNING: sizeof *twl should be sizeof(*twl)
WARNING: sizeof *otg should be sizeof(*otg)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Registering phy_provider before creating the PHY can result in PHY
callbacks being invoked which will lead to aborts. In order to avoid this
invoke phy_provider_register after phy_create and phy_set_drvdata.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/phy/phy.h has stub code in there for when building without the
phy-core enabled. This is useful for generic drivers such as ahci-platform,
ehci-platoform and ohci-platform which have support for driving an optional
phy passed to them through the devicetree.
Since on some boards this phy functionality is not needed, being able to
disable the phy subsystem without needing a lot of #ifdef magic in the
driver using it is quite useful.
However this breaks when the module using the phy subsystem is build-in and
the phy-core is not, which leads to the build failing with missing symbol
errors in the linking stage of the zImage.
Which leads to gems such as this being added to the Kconfig for achi_platform:
depends on GENERIC_PHY || !GENERIC_PHY
Rather then duplicating this code in a lot of places using the phy-core,
I believe it is better to simply not allow the phy-core to be built as a
module. The phy core is quite small and has no external dependencies, so
always building it in when enabling it should not be an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-core allows phy_init and phy_power_on to be called multiple times,
but before this patch -ENOSUPP from phy_pm_runtime_get_sync would be
propagated to the caller for the 2nd and later calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In various cases errors may be expected, ie probe-deferral or a call to
phy_get from a driver where the use of a phy is optional.
Rather then adding all sort of complicated checks for this, and/or adding
special functions like devm_phy_get_optional, simply don't log an error,
and let deciding if get_phy returning an error really should result in a
dev_err up to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/phy/phy-bcm-kona-usb2.c:114: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_phy_optional_get and phy_optional_get, which should be used
when the phy is optional. They does not return an error when the phy
does not exist, rather they returns NULL, which is considered as a valid
phy, but results in NOPs when used with the consumer API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The common clock framework considers NULL a valid clock
reference. This makes handling optional clocks simple, in that if the
optional clock is not available, a NULL reference can be used in the
place of a real clock, simplifying the clock consumer.
Extend this concept to the phy consumer API. A NULL can be passed to
the release calls, the phy_init() and phy_exit() calls, and
phy_power_on() and phy_power_off() and a NOP is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `exynos_mipi_video_phy_probe':
drivers/phy/phy-exynos-mipi-video.c:130: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kirkwood and Dove can turn the SATA phy on and off. Add a PHY driver
to control this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There were a few places where variables are initialized unncessarily.
Remove those initializations.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Increment 'init_count' only if the 'init' callback succeeded and decrement
'init_count' only if the 'exit' callback succeded. Increment 'power_count'
only if 'power_on' callback succeded and if it failed disable the clocks using
phy_pm_runtime_put_sync(). Also decrement 'power_count' only if 'power_off'
callback succeded and if it failed do not disable the clocks.
Reported-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case pm_runtime_get*() fails, it still
increments pm usage counter, so we *must*
make sure to pm_runtime_put() even in those
cases.
This patch fixes that mistake the same way
usbcore treats those possible failures.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver for the internal Broadcom Kona USB 2.0 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes
warning: (OMAP_USB2 && TWL4030_USB) selects USB_PHY which has unmet
direct dependencies (USB_SUPPORT)
that shows up while disabling USB_SUPPORT from menuconfig.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this was called with a NULL "dev" then it lead to a NULL dereference
when we called dev_WARN(). I have changed it to WARN_ON() so that we
get a stack dump and can fix the caller.
The rest of this patch is just cleanup like returning directly instead
of having do-nothing gotos. Using descriptive labels instead of
GW-BASIC style "err0" and "err1". I also flipped the order of
put_device() and ida_remove() so they are a mirror reflection of the
order they were allocated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'phy' was not being freed upon error in one of the cases.
Adjust the 'goto's to fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSZRSSAAoJEIaOsuA1yqRE6EAP/AuF0dWV3wNSuv5h3ZPOybu8
uULX0E/VA2aGs8/55FeuQIJAn499zdt0KH5l8P3CGrKBPk8BN/rD55a6uwYEfWO8
wwTJpVeRyRQS8jes22vPqA22TXgl88SJO0RrsCarrzOcMNloVtOA4zyorITuGZQB
jEKmf9BdjIUlzZkH9t33v3O8kB5pJ1YvBQGRWXbBZvxSzohPC2LYerZKMPN99hDB
2YnJXVKZqZzKbcQQmJklWqRo0RTprWz0Mqcu2r8Lnnn2ZqnT3RBmCBsYXefsp4nF
egRJy51DiypEYt3/OEBf21BySjZHjO6+9jfzOmuOGoEiqw6XCRFMydVpqJJHC8WX
MoCs31VnGwwwBpSOz9ECS9QYXne9jx/bJ6iKoS736sgA20ZA6wBbEDhJlTckcZtm
TEC+UTKevNACAP8cjhGEquqwt5H/rMaYFMXEYQj+gvO2jDsNUGWb74l5VDaBiIm7
GzdUmgmYym8HKT80tgEcgvsUoUphDeNE84OW/jo1nFUDvCniLfQBAYZooEnTHY2H
AW+DqimJzNnKcHo4w/HUQhRgK9147aRbskmVIbepIIW7WQdFQBOPVy7BbfnVD2vA
j01JPshgtnjb+MZb6VqnbcaWKPnJr3KTnOpTTMyk5pKnBOf6PHb1S1Tq5uqtW2Ki
gqi/SXZJ1bYDVaaspNWr
=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Fix argument passed to the register setup helper function so
the phy is actually disabled. Now due to cut&paste error 1 is
passed to both phy_power_on() and phy_power_off().
Reported by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a PHY provider driver for the Samsung Exynos SoC Display Port PHY.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
As we don't support non-DT boot, we just bail out on probe
if device node is not present.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that twl4030-usb is adapted to the new generic PHY framework,
*set_suspend* and *phy_init* ops can be removed from twl4030-usb driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Used the generic PHY framework API to create the PHY. For powering on
and powering off the PHY, power_on and power_off ops are used. Once the
MUSB OMAP glue is adapted to the new framework, the suspend and resume
ops of usb phy library will be removed. Also twl4030-usb driver is moved
to drivers/phy/.
However using the old usb phy library cannot be completely removed
because otg is intertwined with phy and moving to the new
framework completely will break otg. Once we have a separate otg state machine,
we can get rid of the usb phy library.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Used the generic PHY framework API to create the PHY. Now the power off and
power on are done in omap_usb_power_off and omap_usb_power_on respectively.
The omap-usb2 driver is also moved to driver/phy.
However using the old USB PHY library cannot be completely removed
because OTG is intertwined with PHY and moving to the new framework
will break OTG. Once we have a separate OTG state machine, we
can get rid of the USB PHY library.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY framework provides a set of APIs for the PHY drivers to
create/destroy a PHY and APIs for the PHY users to obtain a reference to the
PHY with or without using phandle. For dt-boot, the PHY drivers should
also register *PHY provider* with the framework.
PHY drivers should create the PHY by passing id and ops like init, exit,
power_on and power_off. This framework is also pm runtime enabled.
The documentation for the generic PHY framework is added in
Documentation/phy.txt and the documentation for dt binding can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>