Vertical flip state is exported in xilinx_vdma_config and depending
on IP configuration(c_enable_vert_flip) vertical flip state is
programmed in hardware.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes the below sparse warning in the driver
drivers/dma/xilinx/xilinx_dma.c: In function ‘xilinx_vdma_dma_prep_interleaved’:
drivers/dma/xilinx/xilinx_dma.c:1614:43: warning: variable ‘prev’ set but not used [-Wunused-but-set-variable]
struct xilinx_vdma_tx_segment *segment, *prev = NULL;
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the hardware is configured for Scatter Gather(SG) mode,
and hardware is idle, in the control register SG mode bit
must be set to a 0 then back to 1 by the software, to force
the CDMA SG engine to use a new value written to the CURDESC_PNTR
register, failure to do so could result errors from the dmaengine.
This patch updates the same.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
some typos is comments, so fix them up
/s/enusres/ensures
/s/descripotrs/descriptors
/s/Submited/Submitted
/s/pollling/polling
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates the probe banner info based on the ip probed.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes below.
ERROR: open brace '{' following function definitions go on the next line
+static int xilinx_dma_child_probe(struct xilinx_dma_device *xdev,
+ struct device_node *node) {
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the kernel doc warnings
in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As per axi dmaengine spec the software must not move the tail pointer
to a location that has not been updated (next descriptor field of the
h/w descriptor should always point to a valid address).
When user submits multiple descriptors on the recv side, with the
current driver flow the last buffer descriptor next descriptor field
points to a invalid location, resulting the invalid data or errors from the
axidma dmaengine.
This patch fixes this issue by creating a buffer descritpor chain during
channel allocation itself and use those buffer descriptors for the
subsequent dma operations.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
VDMA engine default frame buffer configuration is cirular mode.
in this mode dmaengine continuously circles through h/w configured fstore
frame buffers.
When vdma h/w is configured for more than one frame.
for example h/w is configured for n number of frames, user
submits less than n number of frames and triggered the dmaengine
using issue_pending API.
since the h/w (or) driver default configuraiton is circular mode
h/w tries to write/read from an invalid frame buffer resulting
errors from the vdma dmaengine.
This patch fixes this issue by enabling the park mode as
default mode configuration for frame buffers in s/w,
so that driver can handle all cases for "k" frames where n%k==0
(n is a multiple of k) by simply replicating the frame pointers.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add variable for checking channel idle state to ensure that dma
descriptor is not submitted when dmaengine is in progress.
This will avoid the polling for a bit in the status register to know
dma state in the driver hot path.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Incase of interrupt property is not present,
Driver is trying to free an invalid irq,
This patch fixes it by adding a check before freeing the irq.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below issues.
--> Need to clear the channel data count register
when overflow interrupts occurs.
--> Reduce the log level from _info to _dbg when
overflow interrupt occurs.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below warning
drivers/dma/xilinx/zynqmp_dma.c: In function 'zynqmp_dma_handle_ovfl_int':
drivers/dma/xilinx/zynqmp_dma.c:522:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below kernel doc warnings
drivers/dma/xilinx/zynqmp_dma.c:552: info: Scanning doc for
zynqmp_dma_device_config
drivers/dma/xilinx/zynqmp_dma.c:558: warning: No description found for
return value of 'zynqmp_dma_device_config'
drivers/dma/xilinx/zynqmp_dma.c:649: info: Scanning doc for
zynqmp_dma_free_descriptors
drivers/dma/xilinx/zynqmp_dma.c:653: warning: No description found for
parameter 'chan'
drivers/dma/xilinx/zynqmp_dma.c:653: warning: Excess function parameter
'dchan' description in 'zynqmp_dma_free_descriptors'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds runtime pm support in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The enum xdma_ip_type is only used inside the Xilinx DMA driver and not
exported to any consumers (nor should it be). So move it from the global
header to driver file itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
'err' is a signed int and error codes are typically negative numbers, so
use '%d' instead of '%u' to format the error code in the error message.
Fixes: ba16db36b5 ("dmaengine: vdma: Add clock support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove check for "len > ZYNQMP_DMA_MAX_TRANS_LEN" as its not needed.
If the length is larger, the transfer is split up into multiple parts
with the max descriptor length already.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_prep_dma_memcpy() callback for this driver allocates a new
xilinx_dma_tx_descriptor whose TX segments list is initialized as empty,
but then gets invalid TX segment pointer by list_last_entry() from the
empty TX segments list and memory corruption happens by the attempt to
update the next descriptor in invalid TX segment pointer.
This removes unnecessary memory access for nonexistent tail TX segment
which causes memory corruption.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_terminate_all() callback for this driver stops current DMA
operations by clearing RUNSTOP bit in the control register and waiting
HALTED bit set in the status register.
But AXI CDMA which is one of the supported DMA engine by this driver
does not provide the run / stop controls and those bits in the control
and status registers are reserved. So when device_terminate_all() is
called, the error message is printed and the channel is marked as having
errors in xilinx_dma_halt().
This change adds stop_transfer() callback which differentiates CDMA and
other DMA engine. The CDMA's one avoids the unsupported operations and
instead polls the status register to check if the DMA operations are in
progress for AXI CDMA.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We get a warning about the missing MODULE_LICENSE tag for this newly
added driver module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/dma/xilinx/zynqmp_dma.o
see include/linux/module.h for more information
This adds a "GPL" license, matching the "version 2 or later" information in
the comment at the start of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly added zynqmp_dma driver produces a warning on 32-bit architectures
when dma_addr_t is 64-bit wide:
drivers/dma/xilinx/zynqmp_dma.c: In function 'zynqmp_dma_config_sg_ll_desc':
drivers/dma/xilinx/zynqmp_dma.c:321:9: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
((dma_addr_t)sdesc - (dma_addr_t)chan->desc_pool_v);
^
drivers/dma/xilinx/zynqmp_dma.c:321:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
((dma_addr_t)sdesc - (dma_addr_t)chan->desc_pool_v);
This changes the cast to the more appropriate uintptr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In cyclic DMA mode need to link the tail bd segment
with the head bd segment to process bd's in cyclic.
Current driver is doing this only for tx channel
needs to update the same for rx channel case also.
This patch fixes the same.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Added the driver for zynqmp dma engine used in Zynq
UltraScale+ MPSoC. This dma controller supports memory to memory
and I/O to I/O buffer transfers.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current driver assumes that child node channel name is either
"xlnx,axi-vdma-mm2s-channel" or "xlnx,axi-vdma-s2mm-channel"
which is confusing the users of AXI DMA and CDMA.
This patch fixes this issue by using different channel
names for the AXI DMA and AXI CDMA child nodes.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the existing vdma driver support for
AXI DMA and CDMA got added so the driver is no
longer VDMA specific.
This patch renames the driver and DT binding doc to xilinx_dma
and updates the Kconfig description for all the DMAS.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for AXI DMA multi-channel dma mode
Multichannel mode enables DMA to connect to multiple masters
and slaves on the streaming side.
In Multichannel mode AXI DMA supports 2D transfers.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AXI CDMA is a soft ip, which can be programmed to support
32 bit addressing or greater than 32 bit addressing.
When the AXI CDMA ip is configured for 32 bit address space
in simple dma mode the source/destination buffer address is
specified by a single register(18h for Source buffer address and
20h for Destination buffer address). When configured in SG mode
the current descriptor and tail descriptor are specified by a
Single register(08h for curdesc 10h for tail desc).
When the AXI CDMA core is configured for an address space greater
than 32 then each buffer address or descriptor address is specified by
a combination of two registers.
The first register specifies the LSB 32 bits of address,
while the next register specifies the MSB 32 bits of address.
For example, 08h will specify the LSB 32 bits while 0Ch will
specify the MSB 32 bits of the first start address.
So we need to program two registers at a time.
This patch adds the 64 bit addressing support to the axicdma
IP in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AXI DMA is a soft ip, which can be programmed to support
32 bit addressing or greater than 32 bit addressing.
When the AXI DMA ip is configured for 32 bit address space
in simple dma mode the buffer address is specified by a single register
(18h for MM2S channel and 48h for S2MM channel). When configured in SG mode
The current descriptor and tail descriptor are specified by a single
Register(08h for curdesc 10h for tail desc for MM2S channel and 38h for
Curdesc and 40h for tail desc for S2MM).
When the AXI DMA core is configured for an address space greater
than 32 then each buffer address or descriptor address is specified by
a combination of two registers.
The first register specifies the LSB 32 bits of address,
while the next register specifies the MSB 32 bits of address.
For example, 48h will specify the LSB 32 bits while 4Ch will
specify the MSB 32 bits of the first start address.
So we need to program two registers at a time.
This patch adds the 64 bit addressing support for the axidma
IP in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly added xilinx_dma_prep_dma_cyclic function sometimes causes
a gcc warning about the use of the segment function in case
we never run into the inner loop of the function:
dma/xilinx/xilinx_vdma.c: In function 'xilinx_dma_prep_dma_cyclic':
dma/xilinx/xilinx_vdma.c:1808:23: error: 'segment' may be used uninitialized in this function [-Werror=maybe-uninitialized]
segment->hw.control |= XILINX_DMA_BD_SOP;
This can only happen if the period len is zero (which would cause other
problems earlier), or if the buffer is shorter than a period. Neither
of them should ever happen, but by adding an explicit check for these two
cases, we can abort in a more controlled way, and the compiler is
able to see that we never use uninitialized data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below compilation warining.
drivers/dma/xilinx/xilinx_vdma.c: In function 'xilinx_dma_prep_dma_cyclic':
drivers/dma/xilinx/xilinx_vdma.c:1808:23: warning: 'segment' may be used
uninitialized in this function [-Wmaybe-uninitialized]
segment->hw.control |= XILINX_DMA_BD_SOP;
The start of packet (SOP) should be set to the first segment in the desc
chain not for the last segment of the desc chain.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_pool_zalloc combines dma_pool_alloc and memset 0
this patch updates the driver to use dma_pool_zalloc.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for AXI DMA cyclic dma mode.
In cyclic mode, DMA fetches and processes the same
BDs without interruption. The DMA continues to fetch and process
until it is stopped or reset.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Added basic clock support for axi dma's.
The clocks are requested at probe and released at remove.
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds config structure in the driver to differentiate
AXI DMA's and to add more features(clock support etc..) to these DMA's.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the AXI Central Direct Memory Access
(AXI CDMA) core to the existing vdma driver, AXI CDMA is a
soft Xilinx IP core that provides high-bandwidth
Direct Memory Access(DMA) between a memory-mapped
source address and a memory-mapped destination address.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the AXI Direct Memory Access (AXI DMA)
core in the existing vdma driver, AXI DMA Core is a
soft Xilinx IP core that provides high-bandwidth
direct memory access between memory and AXI4-Stream
type target peripherals.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch renames the xilinx_vdma_ prefix to xilinx_dma
for the API's and masks that will be shared b/w three DMA
IP cores.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below checkpatch.pl warnings.
WARNING: void function return statements are not generally useful
+ return;
+}
WARNING: void function return statements are not generally useful
+ return;
+}
WARNING: Missing a blank line after declarations
+ u32 errors = status & XILINX_VDMA_DMASR_ALL_ERR_MASK;
+ vdma_ctrl_write(chan, XILINX_VDMA_REG_DMASR,
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When VDMA is configured in Non-sg mode
Users can queue descriptors greater than h/w configured frames.
Current driver allows the user to queue descriptors upto h/w configured.
Which is wrong for non-sg mode configuration.
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This VDMA is a soft ip, which can be programmed to support
32 bit addressing or greater than 32 bit addressing.
When the VDMA ip is configured for 32 bit address space
the buffer address is specified by a single register
(0x5C for MM2S and 0xAC for S2MM channel).
When the VDMA core is configured for an address space greater
than 32 then each buffer address is specified by a combination of
two registers.
The first register specifies the LSB 32 bits of address,
while the next register specifies the MSB 32 bits of address.
For example, 5Ch will specify the LSB 32 bits while 60h will
specify the MSB 32 bits of the first start address.
So we need to program two registers at a time.
This patch adds the 64 bit addressing support to the vdma driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When client request a non existing channel from of_dma_xilinx_xlate
we get a NULL pointer dereferencing. This patch fix this problem.
Signed-off-by: Franck Jullien <franck.jullien@odyssee-systemes.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Radhey Shyam Pandey