By disabling a power domain asynchronously we can restrict holding a
reference on that power domain to the actual code sequence that
requires the power to be on for the HW access it's doing, by also
avoiding unneeded on-off-on togglings of the power domain (since the
disabling happens with a delay).
One benefit is potential power saving due to the following two reasons:
1. The fact that we will now be holding the reference only for the
necessary duration by the end of the patchset. While simply not
delaying the disabling has the same benefit, it has the problem that
frequent on-off-on power switching has its own power cost (see the 2.
point below) and the debug trace for power well on/off events will
cause a lot of dmesg spam (see details about this further below).
2. Avoiding the power cost of freuqent on-off-on power switching. This
requires us to find the optimal disabling delay based on the measured
power cost of on->off and off->on switching of each power well vs.
the power of keeping the given power well on.
In this patchset I'm not providing this optimal delay for two
reasons:
a) I don't have the means yet to perform the measurement (with high
enough signal-to-noise ratio, or with the help of an energy
counter that takes switching into account). I'm currently looking
for a way to measure this.
b) Before reducing the disabling delay we need an alternative way for
debug tracing powerwell on/off events. Simply avoiding/throttling
the debug messages is not a solution, see further below.
Note that even in the case where we can't measure any considerable
power cost of frequent on-off switching of powerwells, it still would
make sense to do the disabling asynchronously (with 0 delay) to avoid
blocking on the disabling. On VLV I measured this disabling time
overhead to be 1ms on average with a worst case of 4ms.
In the case of the AUX power domains on ICL we would also need to keep
the sequence where we hold the power reference short, the way it would
be by the end of this patchset where we hold it only for the actual AUX
transfer. Anything else would make the locking we need for ICL TypeC
ports (whenever we hold a reference on any AUX power domain) rather
problematic, adding for instance unnecessary lockdep dependencies to
the required TypeC port lock.
I chose the disabling delay to be 100msec for now to avoid the unneeded
toggling (and so not to introduce dmesg spamming) in the DP MST sideband
signaling code. We could optimize this delay later, once we have the
means to measure the switching power cost (see above).
Note that simply removing/throttling the debug tracing for power well
on/off events is not a solution. We need to know the exact spots of
these events and cannot rely only on incorrect register accesses caught
(due to not holding a wakeref at the time of access). Incorrect
powerwell enabling/disabling could lead to other problems, for instance
we need to keep certain powerwells enabled for the duration of modesets
and AUX transfers.
v2:
- Clarify the commit log parts about power cost measurement and the
problem of simply removing/throttling debug tracing. (Chris)
- Optimize out local wakeref vars at intel_runtime_pm_put_raw() and
intel_display_power_put_async() call sites if
CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n. (Chris)
- Rebased on v2 of the wakeref w/o power-on guarantee patch.
- Add missing docbook headers.
v3:
- Checkpatch spelling/missing-empty-line fix.
v4:
- Fix unintended local wakeref var optimization when using
call-arguments with side-effects, by using inline funcs instead of
macros. In this patch in particular this will fix the
intel_display_power_grab_async_put_ref()->intel_runtime_pm_put_raw()
call).
No size change in practice (would be the same disregarding the
corresponding change in intel_display_power_grab_async_put_ref()):
$ size i915-macro.ko
text data bss dec hex filename
2455190 105890 10272 2571352 273c58 i915-macro.ko
$ size i915-inline.ko
text data bss dec hex filename
2455195 105890 10272 2571357 273c5d i915-inline.ko
Kudos to Stan for reporting the raw-wakeref WARNs this issue caused. His
config has CONFIG_DRM_I915_DEBUG_RUNTIME_PM=n, which I didn't retest
after v1, and we are also not testing this config in CI.
Now tested both with CONFIG_DRM_I915_DEBUG_RUNTIME_PM=y/n on ICL,
connecting both Chamelium and regular DP, HDMI sinks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513192533.12586-1-imre.deak@intel.com
If the HW fails to ack a change in forcewake status, the machine is as
good as dead -- it may recover, but in reality it missed the mmio
updates and is now in a very inconsistent state. If it happens, we can't
trust the CI results (or at least the fails may be genuine but due to
the HW being dead and not the actual test!) so reboot the machine (CI
checks for a kernel taint in between each test and reboots if the
machine is tainted).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190508115245.27790-1-chris@chris-wilson.co.uk
For us KBP is 100% identical to SPT. Kill the redundant enum
value. Also bspec doesn't talk about KBP either, so this might
avoid some confusion when cross checking the code against the
spec.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190506152627.20283-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The original intent for the delay before running the idle_work was to
provide a hysteresis to avoid ping-ponging the device runtime-pm. Since
then we have also pulled in some memory management and general device
management for parking. But with the inversion of the wakeref handling,
GEM is no longer responsible for the wakeref and by the time we call the
idle_work, the device is asleep. It seems appropriate now to drop the
delay and just run the worker immediately to flush the cached GEM state
before sleeping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507121108.18377-2-chris@chris-wilson.co.uk
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
While at it, rename intel_i2c.c to intel_gmbus.c and the functions to
intel_gmbus_*.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5834b8fbbfd4ac2e3d0159e69c87f6926066f537.1556809195.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2843b028d65e118dc40316aa84bf620a93f6c67b.1556809195.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9bc1317a67df0b9d019eca5b36f474b76a1cad26.1556809195.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9101a58b9f10bcf11332175e17b6e6e45f4ebd17.1556809195.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/876a1671a84c6839bcafdf276cf9c4e1da6c631c.1556809195.git.jani.nikula@intel.com
The workqueue code complains viciously if we try to queue more work onto
the queue while attampting to drain it. As we asynchronously free
objects and defer their enqueuing with RCU, it is quite tricky to
quiesce the system before attempting to drain the workqueue. Yet drain
we must to ensure that the worker is idle before unloading the module.
Give the freed object drain 3 whole passes with multiple rcu_barrier()
to give the defer freeing of several levels each protected by RCU and
needing a grace period before its parent can be freed, ultimately
resulting in a GEM object being freed after another RCU period.
A consequence is that it will make module unload even slower.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110550
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190501135753.8711-1-chris@chris-wilson.co.uk
Make the engine responsible for cleaning itself up!
This removes the i915->gt.cleanup vfunc that has been annoying the
casual reader and myself for the last several years, and helps keep a
future patch to add more cleanup tidy.
v2: Assert that engine->destroy is set after the backend starts
allocating its own state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190501103204.18632-1-chris@chris-wilson.co.uk
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6aea17072684dec0b04b6831c0c0e5a134edf87e.1556540890.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87904259868782c1ad664d852b27a50c1597cfaa.1556540890.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/76d2719b462004ec6f6f5c302ee5d3876357c599.1556540890.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2e4fb1e67ed38870df3040bb0a1b1a58fd90cc86.1556540890.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
i915_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the header remains self-contained, and do so with minimal further
includes, using forward declarations as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cf9b17d56489e15d82356575037432ad04712475.1556540890.git.jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
v2: fix sparse warnings on undeclared global functions
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190429125011.10876-1-jani.nikula@intel.com
It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.
Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.
No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64e46278dc8dccc9c548ef453cb2ceece5367bb2.1556540890.git.jani.nikula@intel.com
We now have two locks for sideband access. The general one covering
sideband access across all generation, sb_lock, and a specific one
covering sideband access via the punit on vlv/chv. After lifting the
sb_lock around the punit into the callers, the pcu_lock is now redudant
and can be separated from its other use to regulate RPS (essentially
giving RPS a lock all of its own).
v2: Extract a couple of minor bug fixes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190426081725.31217-4-chris@chris-wilson.co.uk
As we now employ a very heavy pm_qos around the punit access, we want to
minimise the number of synchronous requests by performing one for the
whole punit sequence rather than around individual accesses. The
sideband lock is used for this, so push the pm_qos into the sideband
lock acquisition and release, moving it from the lowlevel punit rw
routine to the callers. In the first step, we move the punit magic into
the common sideband lock so that we can acquire a bunch of ports
simultaneously, and if need be extend the workaround protection later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190426081725.31217-2-chris@chris-wilson.co.uk
While we talk to the punit over its sideband, we need to prevent the cpu
from sleeping in order to prevent a potential machine hang.
Note that by itself, it appears that pm_qos_update_request (via
intel_idle) doesn't provide a sufficient barrier to ensure that all core
are indeed awake (out of Cstate) and that the package is awake. To do so,
we need to supplement the pm_qos with a manual ping on_each_cpu.
v2: Restrict the heavy-weight wakeup to just the ISOF_PORT_PUNIT, there
is insufficient evidence to implicate a wider problem atm. Similarly,
restrict the w/a to Valleyview, as Cherryview doesn't have an angry cadre
of users.
The working theory, courtesy of Ville and Hans, is the issue lies within
the power delivery and so is likely to be unit and board specific and
occurs when both the unit/fw require extra power at the same time as the
cpu package is changing its own power state.
References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
References: https://bugs.freedesktop.org/show_bug.cgi?id=102657
References: https://bugzilla.kernel.org/show_bug.cgi?id=195255
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190426081725.31217-1-chris@chris-wilson.co.uk
In the current scheme, on submitting a request we take a single global
GEM wakeref, which trickles down to wake up all GT power domains. This
is undesirable as we would like to be able to localise our power
management to the available power domains and to remove the global GEM
operations from the heart of the driver. (The intent there is to push
global GEM decisions to the boundary as used by the GEM user interface.)
Now during request construction, each request is responsible via its
logical context to acquire a wakeref on each power domain it intends to
utilize. Currently, each request takes a wakeref on the engine(s) and
the engines themselves take a chipset wakeref. This gives us a
transition on each engine which we can extend if we want to insert more
powermangement control (such as soft rc6). The global GEM operations
that currently require a struct_mutex are reduced to listening to pm
events from the chipset GT wakeref. As we reduce the struct_mutex
requirement, these listeners should evaporate.
Perhaps the biggest immediate change is that this removes the
struct_mutex requirement around GT power management, allowing us greater
flexibility in request construction. Another important knock-on effect,
is that by tracking engine usage, we can insert a switch back to the
kernel context on that engine immediately, avoiding any extra delay or
inserting global synchronisation barriers. This makes tracking when an
engine and its associated contexts are idle much easier -- important for
when we forgo our assumed execution ordering and need idle barriers to
unpin used contexts. In the process, it means we remove a large chunk of
code whose only purpose was to switch back to the kernel context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424200717.1686-5-chris@chris-wilson.co.uk
For controlling runtime pm of the GT and engines, we would like to have
a callback to do extra work the first time we wake up and the last time
we drop the wakeref. This first/last access needs serialisation and so
we encompass a mutex with the regular intel_wakeref_t tracker.
v2: Drop the _once naming and report the errors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc; Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424200717.1686-1-chris@chris-wilson.co.uk
Start partitioning off the code that talks to the hardware (GT) from the
uapi layers and move the device facing code under gt/
One casualty is s/intel_ringbuffer.h/intel_engine.h/ with the plan to
subdivide that header and body further (and split out the submission
code from the ringbuffer and logical context handling). This patch aims
to be simple motion so git can fixup inflight patches with little mess.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424174839.7141-1-chris@chris-wilson.co.uk
As we push for better compartmentalisation, it is more convenient to
copy the default sseu configuration from the engine into the derived
logical context, than it is to dig it out from i915->runtime_info.
v2: Use intel_sseu_from_device_info() to describe the converter
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424095134.30249-1-chris@chris-wilson.co.uk
When we are called to relieve mempressue via the shrinker, the only way
we can make progress is either by discarding unwanted pages (those
objects that userspace has marked MADV_DONTNEED) or by reclaiming the
dirty objects via swap. As we know that is the only way to make further
progress, we can initiate the writeback as we invalidate the objects.
This means the objects we put onto the inactive anon lru list are
already marked for reclaim+writeback and so will trigger a wait upon the
writeback inside direct reclaim, greatly improving the success rate of
direct reclaim on i915 objects.
The corollary is that we may start a slow swap on opportunistic
mempressure from the likes of the compaction + migration kthreads. This
is limited by those threads only being allowed to shrink idle pages, but
also that if we reactivate the page before it is swapped out by gpu
activity, we only page the cost of repinning the page. The cost is most
felt when an object is reused after mempressure, which hopefully
excludes the latency sensitive tasks (as we are just extending the
impact of swap thrashing to them).
Apparently this is not the first time we've had this idea. Back in
commit 5537252b6b ("drm/i915: Invalidate our pages under memory
pressure") we wanted to start writeback but settled on invalidate after
Hugh Dickins warned us about a possibility of a deadlock within shmemfs
if we started writeback from shrink_slab. Looking at the callchain,
using writeback from i915_gem_shrink should be equivalent to the pageout
also employed by shrink_slab, i.e. it should not be any riskier afaict.
v2: Leave mmapings intact. At this point, the only mmapings of our
objects will be via CPU mmaps on the shmemfs filp, which are
out-of-scope for our LRU tracking. Instead leave those pages to the
inactive anon LRU page list for aging and pageout as normal.
v3: Be selective on which paths trigger writeback, in particular
excluding paths shrinking just to reclaim vm space (e.g. mmap, vmap
reapers) and avoid starting writeback on the entire process space from
within the pm freezer.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108686
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michal Hocko <mhocko@suse.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190420115539.29081-1-chris@chris-wilson.co.uk
For consistency (and elegance!), add intel_device_info.has_rps.
The immediate boon is that RPS support is now emitted along the other
capabilities in the debug log and after errors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419134836.5626-1-chris@chris-wilson.co.uk
On resume, we know that the only pinned contexts in danger of seeing
corruption are the kernel context, and so we do not need to walk the
list of all GEM contexts as we tracked them on each engine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410190120.830-1-chris@chris-wilson.co.uk
As soon as a device is considered unplugged, not only prevent pending
users from accessing the device structures but also cancel all their
pending requests so all consumed resources can be cleaned up as soon
as possible.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190406104034.31380-1-chris@chris-wilson.co.uk
If we have only a single active pipe and the cdclk change only requires
the cd2x divider to be updated bxt+ can do the update with forcing a full
modeset on the pipe. Try to hook that up.
v2:
- Wait for vblank after an optimized CDCLK change.
- Avoid optimization if the pipe needs a modeset (or was disabled).
- Split CDCLK change to a pre/post plane update step.
v3:
- Use correct version of CDCLK state as old state. (Ville)
- Remove unused intel_cdclk_can_skip_modeset()
v4:
- For consistency call intel_set_cdclk_post_plane_update() only during
modesets (and not fastsets).
v5:
- Remove the logic to update the CD2X divider on-the-fly on ICL, since
only a divider of 1 is supported there. Clint also noticed that the
pipe select bits in CDCLK_CTL are oddly defined on ICL, it's not clear
yet whether that's only an error in the specification.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Tested-by: Abhay Kumar <abhay.kumar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327101321.3095-1-imre.deak@intel.com
CDCLK has to be at least twice the BLCK regardless of audio. Audio
driver has to probe using this hook and increase the clock even in
absence of any display.
v2: Use atomic refcount for get_power, put_power so that we can
call each once(Abhay).
v3: Reset power well 2 to avoid any transaction on iDisp link
during cdclk change(Abhay).
v4: Remove Power well 2 reset workaround(Ville).
v5: Remove unwanted Power well 2 register defined in v4(Abhay).
v6:
- Use a dedicated flag instead of state->modeset for min CDCLK changes
- Make get/put audio power domain symmetric
- Rebased on top of intel_wakeref tracking changes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Tested-by: Abhay Kumar <abhay.kumar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320135439.12201-1-imre.deak@intel.com
We want to use intel_engine_mask_t inside i915_request.h, which means
extracting it from the general header file mess and placing it inside a
types.h. A knock on effect is that the compiler wants to warn about
type-contraction of ALL_ENGINES into intel_engine_maskt_t, so prepare
for the worst.
v2: Use intel_engine_mask_t consistently
v3: Move I915_NUM_ENGINES to its natural home at the end of the enum
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401162641.10963-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Concept of a sub-platform already exist in our code (like ULX and ULT
platform variants and similar),implemented via the macros which check a
list of device ids to determine a match.
With this patch we consolidate device ids checking into a single function
called during early driver load.
A few low bits in the platform mask are reserved for sub-platform
identification and defined as a per-platform namespace.
At the same time it future proofs the platform_mask handling by preparing
the code for easy extending, and tidies the very verbose WARN strings
generated when IS_PLATFORM macros are embedded into a WARN type
statements.
v2: Fixed IS_SUBPLATFORM. Updated commit msg.
v3: Chris was right, there is an ordering problem.
v4:
* Catch-up with new sub-platforms.
* Rebase for RUNTIME_INFO.
* Drop subplatform mask union tricks and convert platform_mask to an
array for extensibility.
v5:
* Fix subplatform check.
* Protect against forgetting to expand subplatform bits.
* Remove platform enum tallying.
* Add subplatform to error state. (Chris)
* Drop macros and just use static inlines.
* Remove redundant IRONLAKE_M. (Ville)
v6:
* Split out Ironlake change.
* Optimize subplatform check.
* Use __always_inline. (Lucas)
* Add platform_mask comment. (Paulo)
* Pass stored runtime info in error capture. (Chris)
v7:
* Rebased for new AML ULX device id.
* Bump platform mask array size for EHL.
* Stop mentioning device ids in intel_device_subplatform_init by using
the trick of splitting macros i915_pciids.h. (Jani)
* AML seems to be either a subplatform of KBL or CFL so express it like
that.
v8:
* Use one device id table per subplatform. (Jani)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jose Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327142328.31780-1-tvrtko.ursulin@linux.intel.com
IS_IRONLAKE_M can use the already defined intel_device_info.is_mobile for
this platform, so remove the instance of Ironlake's mobile device id from
the header file and replace it with an IS_MOBILE check.
v2:
* Improved commit text. (Chris)
v3:
* Rebased for EHL.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326074057.27833-3-tvrtko.ursulin@linux.intel.com
This allows the IS_PINEVIEW_<G|M> macros to be removed and avoid
duplication of device ids already defined in i915_pciids.h.
!IS_MOBILE check can be used in place of existing IS_PINEVIEW_G call
sites.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326074057.27833-2-tvrtko.ursulin@linux.intel.com
edram is not part of uncore and there is no requirement for the
detection to be done before we initialize the uncore functions. The
first check on HAS_EDRAM is in the ggtt_init path, so move it to
i915_driver_init_hw, where other dram-related detection happens.
While at it, save the size in MB instead of the capabilities because the
size is the only thing we look at outside of the init function.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190328174533.31532-1-daniele.ceraolospurio@intel.com
The current intel_color_check() is a mess, and worse yet it is
in fact incorrect for several platforms. The hardware has
evolved quite a bit over the years, so let's just go for a clean
split between the platforms by turning this into a vfunc.
The actual work to split it up will follow.
v2: Assign the vfuncs in the order they appear in the
struct (Matt)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327155045.28446-3-ville.syrjala@linux.intel.com
Imre Deak