The kernel test robot reports a boot failure with qemu in 5.5-rc,
referencing commit 2203cbf2c8 ("net: sfp: move fwnode parsing into
sfp-bus layer"). This is caused by phylink_create() being passed a
NULL fwnode, causing fwnode_property_get_reference_args() to return
-EINVAL.
Don't attempt to attach to a SFP bus if we have no fwnode, which
avoids this issue.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd3 ("net: phy: add driver for aquantia phy")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mismerge between the following two commits:
c678726305 ("net: phylink: ensure consistent phy interface mode")
27755ff88c ("net: phylink: Add phylink_mac_link_{up, down} wrapper functions")
resulted in the wrong interface being passed to the mac_link_up()
function. Fix this up.
Fixes: b4b12b0d2f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The commit ef87f7da6b ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes: ef87f7da6b ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.
Fixes: 139d3a212a ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.
Fixes: 6b0da5c9c1 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 3a129e3f9a ("r8169: switch to phylib functions in more places")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to PHY Layer for Ethernet drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used). This patch also gives an explicit
block comment to the SPDX License Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the return paths for all I/O operations to ensure
that the I/O completed successfully. Then pass the return
to the caller for further processing
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to make locking/unlocking the MDIO bus easier.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven reported that using devm_reset_controller_get leads
to a WARNING when probing a reset-controlled PHY. This is because the
device devm_reset_controller_get gets supplied is not actually the
one being probed.
Acquire an unmanaged reset-control as well as free the reset_control on
unregister to fix this.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
There are no users of phy_ethtool_sset() in the kernel anymore, and
as of commit 3c1bcc8614 ("net: ethernet: Convert phydev advertize
and supported from u32 to link mode"), the implementation is slightly
buggy - it doesn't correctly check the masked advertising mask as it
used to.
Remove it, and update the phy documentation to refer to its replacement
function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM. It seems rather common that GPON modules
mis-report.
Let's fix these modules by adding some quirks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for applying module quirks to the list of supported
ethtool link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 075e238d12.
Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.
This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.
Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation on phylink's create and destroy functions to
explicitly state that the rtnl lock must not be held while calling
these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_RESET_CONTROLLER is disabled, the
devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not
handled in subsequent check and then the mdio device fails to probe.
When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset
device, and since it is not present, returns -ENOENT. -ENOENT is handled.
Add -ENOTSUPP also.
This happened to me when upgrading kernel on Turris Omnia. You either
have to enable CONFIG_RESET_CONTROLLER or use this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 71dd6c0dff ("net: phy: add support for reset-controller")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to disable the regulator in remove like what is done
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP+ cages to the Marvell 10G PHY driver. This is
slightly complicated by the way phylib works in that we need to use
a multi-step process to attach the SFP bus, and we also need to track
the phylink state machine to know when the module's transmit disable
signal should change state.
With appropriate DT changes, this allows the SFP+ canges on the
Macchiatobin platform to be functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_support_asym_pause() rather than open-coding it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dp83640 PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp falling edge
Cc: Stefan Sørensen <stefan.sorensen@spectralink.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83869 Gigabit ethernet phy
device.
The DP83869 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the following VSC PHYs
VSC8504, VSC8552, VSC8572
VSC8562, VSC8564, VSC8575, VSC8582
Updates for v2:
Checked for NULL on input to container_of
Changed a large if else series to a switch statement.
Added a WARN_ON to make sure lowest nibble of mask is 0
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0dff ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is inserted, we attempt to read read the ID from address
0x50. Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51. If this
fails, then we fall into error state, and assume that the module is
not usable.
Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately. However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted. This prompts us to fall into the error state.
Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.
Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)
Only report module removal if we had previously reported a module
insertion.
This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the power mode switching from the probe, so that we don't
repeatedly re-probe the SFP device if there is a problem accessing
the registers at I2C address 0x51.
In splitting this out, we can also fix a bug where we leave the module
in high-power mode when the upstream device is detached but the module
is still inserted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the upstream's attachment state in the state machine rather than
maintaining a boolean, which ensures that we have a strict order of
ATTACH followed by an UP event - we can never believe that a newly
attached upstream will be anything but down.
Rearrange the order of state machines so we run the module state
machine after the upstream device's state machine, so the module state
machine can check the current state of the device and take action to
e.g. reset back to empty state when the upstream is detached.
This is to allow the module detection to run independently of the
network device becoming available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_FAULT should be deasserted to indicate that the module has completed
its initialisation. This may include the on-board PHY, so wait until
the module has deasserted TX_FAULT before probing the PHY.
This means that we need an extra state to handle a TX_FAULT that
remains set for longer than t_init, since using the existing handling
state would bypass the PHY probe.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the next state to sfp_sm_fault() so that it can branch to other
states. This will be necessary to improve the initialisation path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using mdelay() to wait before probing the PHY (which holds
several locks, including the rtnl lock), add an extra wait state to
the state machine to introduce the 50ms delay without holding any
locks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King