In ath9k_stop(), tx_complete_work was being cancelled twice.
This patch fixes it. Also, locking sc->mutex should be done
at the beginning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable AsyncFIFO and AGGWEP for AR9287_12 and later revisions only.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).
We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: JD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.
Make ath9k start using this, ath5k is next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the the patch:
ath9k: use new FIF_PSPOLL configure filter
I forgot to add the new FIF_PSPOLL to the supported mask.
Without this we mask out the FIF_PSPOLL flag therefore
we'd ignore it from mac80211.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI uses the beacon RSSI for its operation.
Update this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask can be obtained directly from ath_hw.
Also, use a helper macro for comparing CTLs - this improves readability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write CCK power-per-rate array always and report
correct TX power to regulatory.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps the antenna configuration mechanism
for 4K chips.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A subsequent patch would use these for configuring
antennae on AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regChainOffset is always zero, remove it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to set pspoll filter on ath9k on AP mode but
we no longer need this mode specific check as mac80211
now does the check for us and informs us when we should
enable pspoll through FIF_PSPOLL.
Cc: Igor Perminov <igor.perminov@inbox.ru>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath9k/eeprom.o
drivers/net/wireless/ath/ath9k/eeprom.c: In function ‘ath9k_hw_AR9287_check_eeprom’:
drivers/net/wireless/ath/ath9k/eeprom.c:2866: warning: comparison of distinct pointer types lacks a cast
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will finalize this after some driver core changes, for now
we leave this unsupported.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used later to add support for ar9271.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use typdefs on ath9k, remove that _t.
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_keyreset() has a spurious check for ah->curchan..
remove it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keycache reset will not fail as right above we ensure
to set the sc->keymax to be <= ah->caps.keycache_size. Just remove
this dangling check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hw initialization fails (ath9k_hw_init()) on ath_init_softc()
we bail out and call ath9k_hw_detach(). The call ath9k_hw_detach()
is conditional though as ath9k_hw_init() could itself have called
ath9k_hw_detach(). Just describing this is itself a brain twister.
Avoid this nonsense by removing ath9k_hw_detach() from ath9k_hw_init().
Upon hw initialization failure we expect the callers to take care of
the cleanup.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree(NULL) works so remove all those branches which check
for it before kfree()'ing on ath9k_hw_rfdetach().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We re-label the device driver initialization routines from the
ath_softc, the "Software Carrier" fillers. This should make it
clearer what each of these do.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization ath9k tends to use "attach" to when we
initialize hardware due to the fact we used to attach a "HAL".
The notion of a HAL is long gone, so lets just be clear on what
we are doing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes reading the hardware initialization process
easier to understand. The new helpers added are:
ath9k_hw_init_cal_settings()
ath9k_hw_init_mode_regs()
ath9k_hw_init_mode_gain_regs()
ath9k_hw_init_11a_eeprom_fix()
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're now propagating the -ENOMEM error so there is no need to
keep a debug message there now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The softc is cached and set within the ath_hw struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_attach() was going first through some device id verifier,
and then calling some other helper which was doing the real hardware
initialization. Lets just do the devid checks within the real worker
by calling a helper ath9k_hw_devid_supported().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith