According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In m_can_class_register() the clock is started, but stopped on exit. When
calling m_can_class_unregister(), the clock is stopped a second time.
This patch removes the erroneous m_can_clk_stop() in m_can_class_unregister().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX). SCU driver manages the IPC interface
between host CPU and the SCU firmware running on M4.
For i.MX8QM, stop mode request is controlled by System Controller Unit(SCU)
firmware, this patch introduces FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW quirk
for this function.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-6-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds back support for half-duplex controllers, which was removed in
the last patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-17-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch reworks the SPI access and fixes several probems:
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Do not place variable "addr" on stack and use it as buffer for SPI
transfer. Buffers for SPI transfers must be allocated from DMA save
memory.
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Halfe number of SPI transfers by using a single buffer + memcpy().
This improves the performance, especially on SPI controllers, which
use interrupt based transfers.
- Use "8" bits per word, not "32". This makes it possible to use this
driver on SoCs like the Raspberry Pi, which SPI host controller
drivers only support 8 bits per word.
Note: this breaks half duplex only controllers. Support for them will be
re-added in the next patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-16-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The memory space of the chip is not fully populated, so add a regmap range
table to document this.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tcan4x5x chip support bulk read/write, but as the length field is only 8
bits wide, the maximum is 256. A length of 0 is treated as 256.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sets the regmap stide to 4, as the chip only supports access on 32
bit alligned access.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the context pointer of the regmap callback functions by a
pointer to the spi_device. This saves one level of indirection in the
callbacks.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch simplifies the tcan4x5x_regmap_write(0 function by removing not
needed casts and replaces hardcoded "4" by appropriate sizeof()s.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the regmap_spi_gather_write() function to
tcan4x5x_regmap_gather_write(). Now it has a "tcan4x5x_" prefix as all other
functions in this driver.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver doesn't use regmap async support, so remove the stubs.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With C99 initializers, all non mentioned members are initialzied to 0, so
remove not needed initialization of read_flag_mask.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the struct regmap_bus tcan4x5x_bus as constant.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch to move the regmap related code into a seperate
file. This patch removes the tcan4x5x.c to tcan4x5x-core.c.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch beautifies the indention of the tcan4x5x_of_match and
tcan4x5x_id_table.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the DEVICE_NAME macro by KBUILD_MODNAME and removed the
superfluous DEVICE_NAME.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m_can driver's suspend and resume functions (m_can_class_suspend() and
m_can_class_resume()) make use of dev_get_drvdata() and assume that the drvdata
is a pointer to the struct net_device.
With upcoming conversion of the tcan4x5x driver to pm_runtime this assumption
is no longer valid. As the suspend and resume functions actually need a struct
m_can_classdev pointer, change the m_can_platform and the m_can_pci driver to
hold a pointer to struct m_can_classdev instead, as the tcan4x5x driver already
does.
Link: https://lore.kernel.org/r/20201212175518.139651-8-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch enhances m_can_class_allocate_dev() to allocate driver specific
private data. The driver's private data struct must contain struct
m_can_classdev as its first member followed by the remaining private data.
Link: https://lore.kernel.org/r/20201212175518.139651-7-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch
| dd8088d5a8 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle() in-case-of-error
dance is no longer needed. Convert the m_can driver to use this function.
Link: https://lore.kernel.org/r/20201212175518.139651-6-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function m_can_config_endisable() is not used outside of the m_can driver,
so mark it as static.
Link: https://lore.kernel.org/r/20201212175518.139651-5-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch coverts the m_can driver to use cdev as name for struct
m_can_classdev uniformly throughout the whole driver.
Link: https://lore.kernel.org/r/20201212175518.139651-4-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the indention in the m_can driver to kernel coding style.
Link: https://lore.kernel.org/r/20201212175518.139651-3-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Old versions of the user manual are regularly depublished, so change link to
the linux-can github page, which has a mirror off all published datasheets.
Link: https://lore.kernel.org/r/20201212175518.139651-2-mkl@pengutronix.de
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCP251xFD supports internal loopback mode which can be used to verify CAN
functionality in the absence of a real CAN device.
Link: https://lore.kernel.org/r/20201201054019.11012-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mkl: mcp251xfd_get_normal_mode(): move CAN_CTRLMODE_LOOPBACK check to front]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan driver runs only on DT platforms, so simplify the code by using
of_device_get_match_data() to retrieve the driver data and also by removing the
unused id_table.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201128132855.7724-1-festevam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus.
It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP
block with additional registers which all of them are within the same MMIO
range.
Currently only interrupt control register from wrapper IP is used and the MRAM
configuration is expected to come from the firmware via "bosch,mram-cfg" device
property and parsed by m_can.c core.
Initial implementation is done by Felipe Balbi while he was working at Intel
with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20201117160827.3636264-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparatory patch for upcoming PCI based M_CAN devices. The current
PM implementation would cause PCI based drivers to enable PM twice, once when
the PCI device is added and a second time in m_can_class_register(). This will
cause 'Unbalanced pm_runtime_enable!' to be logged, and is a situation that
should be avoided.
Therefore, in anticipation of PCI devices, move PM enabling out from M_CAN
class registration to its only user, the m_can_platform driver.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Link: https://lore.kernel.org/r/20201023115800.46538-2-patrik.flykt@linux.intel.com
[mkl: m_can_plat_probe(): fix error handling
m_can_class_register(): simplify error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CSR bit is already cleared when arriving here so remove this section of
duplicate code.
The registers set in m_can_config_endisable() is set to same exact values as
before this patch.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191211063227.84259-1-sean@geanix.com
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The definition of IS_ERR() already applies the unlikely() notation when
checking the error status of the passed pointer. For this reason there is no
need to have the same notation outside of IS_ERR() itself.
Clean up code by removing redundant notation.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20201210085321.18693-1-a@unstable.cc
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the function m_can_class_unregister() directly after the
m_can_class_register() function.
Link: https://lore.kernel.org/r/20201130133713.269256-7-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There's no need to unset the drvdata on remove, so remove the unneeded call to
platform_set_drvdata() in m_can_plat_remove().
Link: https://lore.kernel.org/r/20201130133713.269256-6-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Both struct tcan4x5x_priv::mram_start and struct tcan4x5x_priv::reg_offset are
only assigned once with a constant and then always used read-only. This patch
changes the driver to use the constant directly instead.
Link: https://lore.kernel.org/r/20201130133713.269256-2-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the tcan4x5x_parse_config() function to tcan4x5x_get_gpios() since the
function retrieves the gpio configurations from the firmware.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200226140358.30017-1-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the error handling in c_can_power_up(), there are two bugs:
1) c_can_pm_runtime_get_sync() will increase usage counter if device is not
empty. Forgetting to call c_can_pm_runtime_put_sync() will result in a
reference leak here.
2) c_can_reset_ram() operation will set start bit when enable is true. We
should clear it in the error handling.
We fix it by adding c_can_pm_runtime_put_sync() for 1), and
c_can_reset_ram(enable is false) for 2) in the error handling.
Fixes: 8212003260 ("can: c_can: Add d_can suspend resume support")
Fixes: 52cde85acc ("can: c_can: Add d_can raminit support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201128133922.3276973-2-zhangqilong3@huawei.com
[mkl: return "0" instead of "ret"]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sun4i driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sja1000 driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 8935f57e68 ("can: sja1000: fix network statistics update")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The clocks mcan_class->cclk and mcan_class->hclk are not prepared by any call
during tcan4x5x_can_probe(), so remove erroneous clk_disable_unprepare() on
them.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: http://lore.kernel.org/r/20201130114252.215334-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes a redundant return at the end of
tcan4x5x_clear_interrupts().
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: http://lore.kernel.org/r/20191211141635.322577-1-sean@geanix.com
Reported-by: Daniels Umanovskis <daniels@umanovskis.se>
Acked-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reduce the number of separate SPI core requests when setting the UINC bit in
the TEF FIFO, and instead batch them up into a single SPI core request.
Link: https://lore.kernel.org/r/20201126132144.351154-6-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the struct mcp251xfd_tef_ring upwards, so that the union
mcp251xfd_write_reg_buf and struct spi_transfer can be made members of it.
Link: https://lore.kernel.org/r/20201126132144.351154-5-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the struct mcp251xfd_tef_ring member within the struct
mcp251xfd_priv into an array of length one. This way all rings (tef, tx and rx)
can be accessed in the same way.
Link: https://lore.kernel.org/r/20201126132144.351154-4-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by
moving the "default" to the end of the "switch" statement and explicitly adding
a break statement instead of letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: http://lore.kernel.org/r/aab7cf16bf43cc7c3e9c9930d2dae850c1d07a3c.1605896059.git.gustavoars@kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[mkl: move default to end]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It would directly return if the variable err equals to 0 or other errors.
Only when the err equals to -ETIMEDOUT it can reach the 'if (err)'
statement, so the 'if (err)' and last 'return -ETIMEDOUT' statements are
useless. Romove them.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1605605352-25298-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for a new variant of devices using the hydra platform, based on
NXP i.MX RT (flexcan).
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-5-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add USB_{LEAF,HYDRA}_PRODUCT_ID_END defines, representing the last USB PID
entry in respectively family. This removes the need to update the
kvaser_is_{leaf,hydra}() functions whenever new devices are added.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-3-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There haven been reports, that the flexcan_close() soradically hangs during
simultanious ifdown, sending of CAN messages and probably open CAN bus:
| (__schedule) from [<808bbd34>] (schedule+0x90/0xb8)
| (schedule) from [<808bf274>] (schedule_timeout+0x1f8/0x24c)
| (schedule_timeout) from [<8016be44>] (msleep+0x18/0x1c)
| (msleep) from [<80746a64>] (napi_disable+0x60/0x70)
| (napi_disable) from [<8052fdd0>] (flexcan_close+0x2c/0x140)
| (flexcan_close) from [<80744930>] (__dev_close_many+0xb8/0xd8)
| (__dev_close_many) from [<8074db9c>] (__dev_change_flags+0xd0/0x1a0)
| (__dev_change_flags) from [<8074dc84>] (dev_change_flags+0x18/0x48)
| (dev_change_flags) from [<80760c24>] (do_setlink+0x44c/0x7b4)
| (do_setlink) from [<80761560>] (rtnl_newlink+0x374/0x68c)
I was unable to reproduce the issue, but a cleanup of the flexcan close
sequence has probably fixed the problem at the reporting user.
This patch changes the sequence in flexcan_close() to:
- stop the TX queue
- disable the interrupts on the chip level and wait via free_irq()
synchronously for the interrupt handler to finish
- disable RX offload, which disables synchronously NAPI
- disable the flexcan on the chip level
- free RX offload
- disable the transceiver
- close the CAN device
- disable the clocks
Link: https://lore.kernel.org/r/20201119100917.3013281-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the order in which the flexcan controller is brought up
during flexcan_open(). It makes sure that the chip is completely initialized
before the IRQs are requested and finally enabled.
Link: https://lore.kernel.org/r/20201119100917.3013281-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function flexcan_chip_start() first configures the CAN controller and then
enables the interrupt, flexcan_chip_stop() does the opposite.
In an upcoming patch the order of operations in flexcan_open() and
flexcan_close() are changed. This requires
flexcan_chip_start()/flexcan_chip_stop_disable_on_error() and
flexcan_chip_interrupts_{enable,disable}() to be independent of each other.
This patch moves the enabling of the interrupts from flexcan_chip_start() to
its callers flexcan_open() and flexcan_resume(). Likewise the disabling of the
interrupts is moved from __flexcan_chip_stop() to its indirect callers
flexcan_close() and flexcan_suspend().
Link: https://lore.kernel.org/r/20201119100917.3013281-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The upcoming patches are going to move the enabling and disabling of the
interrupts. Introduce convenience functions to make these patches simpler.
Link: https://lore.kernel.org/r/20201119100917.3013281-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch intends to rename FLEXCAN_QUIRK_SETUP_STOP_MODE quirk
to FLEXCAN_QUIRK_SETUP_STOP_MODE_GRP for non-scu SoCs, coming patch will
add quirk for scu SoCs.
For non-scu SoCs, setup stop mode with GPR register.
For scu SoCs, setup stop mode with SCU firmware.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-4-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Support the Classical CAN raw DLC functionality to send and receive DLC values
from 9 .. 15 for the Classical CAN capable CAN network driver esd_usb that
supports the esd CAN-USB/2 and CAN-USB/Micro devices:
- esd_usb2
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Tested-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://lore.kernel.org/r/20201116184430.25462-2-stefan.maetje@esd.eu
[mkl: rewrapped some long lines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Support the Classical CAN raw DLC functionality to send and receive DLC values
from 9 .. 15 on various Classical CAN capable CAN network drivers:
- sja1000
- gs_usb
- pcan_usb
- pcan_usb_fd
- usb_8dev
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201111095923.2535-1-socketcan@hartkopp.net
[mkl: usb_8dev: changed indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper functions can_len2dlc and can_dlc2len are only relevant for
CAN FD data length code (DLC) conversion.
To fit the introduced can_cc_dlc2len for Classical CAN we rename:
can_dlc2len -> can_fd_dlc2len to get the payload length from the DLC
can_len2dlc -> can_fd_len2dlc to get the DLC from the payload length
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The macro was always used together with can_dlc2len() which sanitizes the
given dlc value on its own.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-4-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).
Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Calls to nla_strlcpy are now replaced by calls to nla_strscpy which is the new
name of this function.
Signed-off-by: Francis Laniel <laniel_francis@privacyrequired.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix leaking netdev device from peripherial devices. The call to allocate the
netdev device is made from and managed by the peripherial.
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch creates a common function that peripherials can call to free the
netdev device when failures occur.
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the missing error checking when initializing the regmap
interface fails.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632 ("can: flexcan: implement can Runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the patch
d9b081e3fc ("can: flexcan: remove ack_grp and ack_bit handling from driver")
the unused ack_grp and ack_bit were removed from the driver. However in the
comment, the "req_bit" was accidentally removed, too.
This patch adds back the "req_bit" bit.
Fixes: d9b081e3fc ("can: flexcan: remove ack_grp and ack_bit handling from driver")
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: http://lore.kernel.org/r/20201014114810.2911135-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu>
Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For SoCs with ECC supported, even use FLEXCAN_QUIRK_DISABLE_MECR quirk to
disable non-correctable errors interrupt and freeze mode, had better use
FLEXCAN_QUIRK_SUPPORT_ECC quirk to initialize all memory.
Fixes: cdce844865 ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201020155402.30318-6-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde