There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Now that we have the internal tag as a special (higher) value tag,
it gets a bit tricky to iterate the internal commands as some loops
will exceed ATA_MAX_QUEUE. Add explicit helpers for iterating pending
commands, both inflight and internal.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
Pull libata updates from Tejun Heo:
- libata has always been limiting the maximum queue depth to 31, with
one entry set aside mostly for historical reasons. This didn't use to
make much difference but Jens found out that modern hard drives can
actually perform measurably better with the extra one queue depth.
Jens updated libata core so that it can make use of full 32 queue
depth
- Damien updated command retry logic in error handling so that it
doesn't unnecessarily retry when upper layer (SCSI) is gonna handle
them
- A couple misc changes
* 'for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_fsl: use the right type for tag bitshift
ahci: enable full queue depth of 32
libata: don't clamp queue depth to ATA_MAX_QUEUE - 1
libata: add extra internal command
sata_nv: set host can_queue count appropriately
libata: remove assumption that ATA_MAX_QUEUE - 1 is the max
libata: use ata_tag_internal() consistently
libata: bump ->qc_active to a 64-bit type
libata: convert core and drivers to ->hw_tag usage
libata: introduce notion of separate hardware tags
libata: Fix command retry decision
libata: Honor RQF_QUIET flag
libata: Make ata_dev_set_mode() less verbose
libata: Fix ata_err_string()
libata: Fix comment typo in ata_eh_analyze_tf()
sata_nv: don't use block layer bounce buffer
ata: hpt37x: Convert to use match_string() helper
As far as I can tell this function can't even be called any more, given
that ATA implements its own eh_strategy_handler with ata_scsi_error, which
never calls ->eh_timed_out.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Bump the internal tag to 32, instead of stealing the last tag in
our regular command space. This works just fine, since we don't
actually need a separate hardware tag for this. Internal commands
cannot coexist with NCQ commands.
As a bonus, we get rid of the special casing of what tag to use
for the internal command.
This is in preparation for utilizing all 32 commands for normal IO.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some check for the value directly, use the provided helper instead.
Also make it return a bool, since that's what it does.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation for allowing full usage of the tag space,
which means that our reserved error handling command will be
using an internal tag value of 32. This doesn't fit in a u32, so
move to a u64.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Rigth now these are the same, but drivers should be using ->hw_tag
for their command setup and issue.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Now ata devices attached with sas controller do not have transport
class, so that we can not see any information of these ata devices in
/sys/class/ata_port(or ata_link or ata_device).
Add transport class for the ata devices attached with sas controller.
The /sys/class directory will show the infomation of the ata devices
as follows:
localhost:/sys/class # ls ata*
ata_device:
dev1.0 dev2.0
ata_link:
link1 link2
ata_port:
ata1 ata2
No functional change of the device scanning and io path. The ata
transport class was deleted when destroying the sas devices.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After commit 9a6d6a2dda ("ata: make ata port as parent device of scsi
host") manual driver unbind/remove causes use-after-free.
Unbind unconditionally invokes devres_release_all() which calls
ata_host_release() and frees ata_host/ata_port memory while it is still
being referenced as a parent of SCSI host. When SCSI host is finally
released scsi_host_dev_release() calls put_device(parent) and accesses
freed ata_port memory.
Add reference counting to make sure that ata_host lives long enough.
Bug report: https://lkml.org/lkml/2017/11/1/945
Fixes: 9a6d6a2dda ("ata: make ata port as parent device of scsi host")
Cc: Tejun Heo <tj@kernel.org>
Cc: Lin Ming <minggr@gmail.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As described by Matthew Garret quite a while back:
https://mjg59.dreamwidth.org/34868.html
Intel CPUs starting with the Haswell generation need SATA links to power
down for the "package" part of the CPU to reach low power-states like
PC7 / P8 which bring a significant power-saving with them.
The default max_performance lpm policy does not allow for these high
PC states, both the medium_power and min_power policies do allow this.
The min_power policy saves significantly more power, but there are some
reports of some disks / SSDs not liking min_power leading to system
crashes and in some cases even data corruption has been reported.
Matthew has found a document documenting the default settings of
Intel's IRST Windows driver with which most laptops ship:
https://www-ssl.intel.com/content/dam/doc/reference-guide/sata-devices-implementation-recommendations.pdf
Matthew wrote a patch changing med_power to match those defaults, but
that never got anywhere as some people where reporting issues with the
patch-set that patch was a part of.
This commit is another attempt to make the default IRST driver settings
available under Linux, but instead of changing medium_power and
potentially introducing regressions, this commit adds a new
med_power_with_dipm setting which is identical to the existing
medium_power accept that it enables dipm on top, which makes it match
the Windows IRST driver settings, which should hopefully be safe to
use on most devices.
The med_power_with_dipm setting is close to min_power, except that:
a) It does not use host-initiated slumber mode (ASP not set),
but it does allow device-initiated slumber
b) It does not enable DevSlp mode
On my T440s test laptop I get the following power savings when idle:
medium_power 0.9W
med_power_with_dipm 1.2W
min_power 1.2W
Suggested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The warning message "READ LOG DMA EXT failed, trying unqueued" in
ata_read_log_page() as well as the macro name ATA_HORKAGE_NO_NCQ_LOG
are confusing: the command READ LOG DMA EXT is not an queued NCQ command
unless it is encapsulated in a RECEIVE FPDMA QUEUED command.
From ACS-4 READ LOG DMA EXT description:
"The device processes the READ LOG DMA EXT command in the NCQ feature
set environment (see 4.13.6) if the READ LOG DMA EXT command is
encapsulated in a RECEIVE FPDMA QUEUED command (see 7.30) with the
inputs encapsulated as shown in 7.23.6."
To avoid confusion, fix the warning messsage to mention switching to PIO and
not "unqueued" and rename the macro ATA_HORKAGE_NO_NCQ_LOG to
ATA_HORKAGE_NO_DMA_LOG.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Bartlomiej added pata_falcon
- Christoph is trying to remove use of static 4k buf. It's still WIP
- config cleanup around HAS_DMA
- other fixes and driver-specific changes
* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (29 commits)
ata: pata_of_platform: using of_property_read_u32() helper
pata_atiixp: Don't use unconnected secondary port on SB600/SB700
libata-sff: Don't scan disabled ports when checking for legacy mode.
pata_octeon_cf: remove unused local variables from octeon_cf_set_piomode()
ahci: qoriq: added ls2088a platforms support
ahci: qoriq: report error when ecc register address is missing in dts
ahci: qoriq: added a condition to enable dma coherence
Revert "libata: switch to dynamic allocation instead of ata_scsi_rbuf"
ahci: imx: fix building without hwmon or thermal
ata: add Atari Falcon PATA controller driver
ata: pass queued command to ->sff_data_xfer method
ata: allow subsystem to be used on m68k arch
libata: switch to dynamic allocation instead of ata_scsi_rbuf
libata: don't call ata_scsi_rbuf_fill for command without a response buffer
libata: call ->scsi_done from ata_scsi_simulate
libata: remove the done callback from ata_scsi_args
libata: move struct ata_scsi_args to libata-scsi.c
libata: avoid global response buffer in atapi_qc_complete
libata-eh: Use switch() instead of sparse array for protocol strings
ata: sata_mv: Convert to devm_ioremap_resource()
...
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method. Update core code and all users
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
asm-generic is only intended for architecture defaults, and we can simply
kill it off by moving the two defintions directly to <linux/libata.h>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoid the need to always translate between the two in ata_prot_flags
and generally cleans up the taskfile protocol usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
This way we don't have to worry about the exact bit postition of the
test to leak out and any crazy propagation effects in the callers.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Byte 69 bits 0:1 in the IDENTIFY DEVICE data indicate a
host-aware ZAC device.
Host-managed ZAC devices have their own individual signature,
and to not set the bits in the IDENTIFY DEVICE data.
And whenever we detect a ZAC-compatible device we should
be displaying the zoned block characteristics VPD page.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add NCQ encapsulation for ZAC MANAGEMENT OUT and evaluate
NCQ Non-Data log pages to figure out if NCQ encapsulation
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ZAC drives implement a 'ZAC Management In' command template,
which maps onto the ZBC IN command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata device disabling is ... curious. So add the correct
definitions that we can disable ZAC devices properly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement MODE SELECT for the control mode page to allow the OS
to switch to descriptor sense.
tj: Dropped s/sb/cmd->sense_buffer/ in ata_gen_ata_sense(). Added
@dev description to ata_msense_ctl_mode().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.
Fix this by ensuring that the id buffer is cacheline aligned.
This issue is similar to that fixed by Commit 84bda12af3
("libata: align ap->sector_buf").
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 2.6.18
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI driver code stops and starts port DMA engines at will
without considering the power state of the particular port. The
AHCI specification isn't very clear on how to handle this scenario,
leaving implementation open to interpretation.
Broadcom's STB SATA host controller is unable to handle port DMA
controller restarts when the port in question is in low power mode.
When a port enters partial or slumber mode, its PHY is powered down.
When a controller restart is requested, the controller's internal
state machine expects the PHY to be brought back up by software which
never happens in this case, resulting in failures.
To avoid this situation, logic is added to manually wake up the port
just before its DMA engine is stopped, if the port happens to be in
a low power state. HBA initiated power management ensures that the port
eventually returns to its configured low power state, when the link is
idle (as per the conditions listed in the spec). A new host flag is also
added to ensure this logic is only exercised for hosts with the above
limitation.
tj: Formatting changes.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Mostly low level driver specific changes.
Two changes are somewhat noteworthy. First, Dan's patchset to support
per-port msix interrupt handling for ahci, which was tried last cycle
but had to be backed out due to a couple issues, is back and seems to
be working fine. Second, libata exception handling now uses
usleep_range() instead of msleep() for sleeps < 20ms which can make
things snappier in some corner cases"
* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: skip debounce delay on link resume
ata: ahci_brcmstb: disable DIPM support
ata: ahci_brcmstb: enable support for ALPM
drivers: libata-core: Use usleep_range() instead of msleep() for short sleeps (<20 ms)
sata_sx4: correctly handling failed allocation
ata: ahci_brcmstb: add support for MIPS-based platforms
ahci: qoriq: Adjust the default register values on ls1021a
ahci: qoriq: Update the default Rx watermark value
ahci: qoriq: Adjust the default register values on ls1043a
ahci: compile out msi/msix infrastructure
ata: core: fix irq description on AHCI single irq systems
ata: ahci_brcmstb: remove unused definitions
ata: ahci_brcmstb: add a quirk for MIPS-based platforms
ata: ahci_brcmstb: disable NCQ for MIPS-based platforms
ata: sata_rcar: Remove obsolete platform_device_id entries
sata_rcar: Add compatible string for r8a7795
ahci: kill 'intr_status'
ahci: switch from 'threaded' to 'hardirq' interrupt handling
ahci: per-port msix support
The link resume logic uses a 200msec delay while debouncing
the SControl register. The rationale behind that delay is
to accommodate some PHYs that behave badly if their SStatus/
SControl registers are pounded immediately on resume.
The Broadcom STB SATA PHY does not seem to have this issue.
This patch introduces a new link flag that allows platforms
to skip the debounce delay if it isn't needed.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.
If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the AHCI ports' HPCP or ESP bits are set, the port
should be considered external (e.g. eSATA) and is marked
as removable. Userspace tools like udisks then treat it
like an usb drive.
With this patch applied, when I plug a drive into the esata port,
KDE pops up a window asking what to do with the drives(s), just
like it does for any random USB stick.
Removability is indicated to the upper layers by way of the
SCSI RMB bit, as I haven't found another way to signal
userspace to treat a sata disk like any usb stick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db66e),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before
# cat /sys/block/sdb/queue/max_sectors_kb
512
I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.
tj: Minor comment update.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db66e ("block: remove artifical max_hw_sectors cap")
Some devices lose data on TRIM whether queued or not. This patch adds
a horkage to disable TRIM.
tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some devices advertise support for the READ/WRITE LOG DMA EXT commands
but fail when we try to issue them. This can lead to queued TRIM being
unintentionally disabled since the relevant feature flag is located in a
general purpose log page.
Fall back to unqueued READ LOG EXT if the DMA variant fails while
reading a log page.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata updates from Tejun Heo:
- Hannes's patchset implements support for better error reporting
introduced by the new ATA command spec.
- the deperecated pci_ dma API usages have been replaced by dma_ ones.
- a bunch of hardware specific updates and some cleanups.
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: remove deprecated use of pci api
ahci: st: st_configure_oob must be called after IP is clocked.
ahci: st: Update the ahci_st DT documentation
ahci: st: Update the DT example for how to obtain the PHY.
sata_dwc_460ex: indent an if statement
libata: Add tracepoints
libata-eh: Set 'information' field for autosense
libata: Implement support for sense data reporting
libata: Implement NCQ autosense
libata: use status bit definitions in ata_dump_status()
ide,ata: Rename ATA_IDX to ATA_SENSE
libata: whitespace fixes in ata_to_sense_error()
libata: whitespace cleanup in ata_get_cmd_descript()
libata: use READ_LOG_DMA_EXT
libata: remove ATA_FLAG_LOWTAG
sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
sata_dwc_460ex: move to generic DMA driver
sata_dwc_460ex: join messages back
sata: xgene: add ACPI support for APM X-Gene SATA ports
ata: sata_mv: add proper definitions for LP_PHY_CTL register values
sata_sil24 for some reason pukes when tags are allocated round-robin
which helps tag ordered controllers. To work around the issue,
72dd299d50 ("libata: allow sata_sil24 to opt-out of tag ordered
submission") introduced ATA_FLAG_LOWTAG which tells libata tag
allocation to do lowest-first.
However, with the recent switch to blk-mq tag allocation, the liata
tag allocation code path is no longer used and the workaround is now
implemented in the block layer and selected by setting
scsi_host_template->tag_alloc_policy to BLK_TAG_ALLOC_FIFO. See
9269e23496 ("libata: make sata_sil24 use fifo tag allocator").
This leaves ATA_FLAG_LOWTAG withoout any actual user. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Dan Williams <dan.j.williams@intel.com>
SAS controller has its own tag allocation, which doesn't directly match to ATA
tag, so SAS and SATA have different code path for ata tags. Originally we use
port->scsi_host (98bd4be1) to destinguish SAS controller, but libsas set
->scsi_host too, so we can't use it for the destinguish, we add a new flag for
this purpose.
Without this patch, the following oops can happen because scsi-mq uses
a host-wide tag map shared among all devices with some integer tag
values >= ATA_MAX_QUEUE. These unexpectedly high tag values cause
__ata_qc_from_tag() to return NULL, which is then dereferenced in
ata_qc_new_init().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
PGD 32adf0067 PUD 32adf1067 PMD 0
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi igb
i2c_algo_bit ptp pps_core pm80xx libsas scsi_transport_sas sg coretemp
eeprom w83795 i2c_i801
CPU: 4 PID: 1450 Comm: cydiskbench Not tainted 4.0.0-rc3 #1
Hardware name: Supermicro X8DTH-i/6/iF/6F/X8DTH, BIOS 2.1b 05/04/12
task: ffff8800ba86d500 ti: ffff88032a064000 task.ti: ffff88032a064000
RIP: 0010:[<ffffffff804fd46e>] [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
RSP: 0018:ffff88032a067858 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8800ba0d2230 RCX: 000000000000002a
RDX: ffffffff80505ae0 RSI: 0000000000000020 RDI: ffff8800ba0d2230
RBP: ffff88032a067868 R08: 0000000000000201 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800ba0d0000
R13: ffff8800ba0d2230 R14: ffffffff80505ae0 R15: ffff8800ba0d0000
FS: 0000000041223950(0063) GS:ffff88033e480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000058 CR3: 000000032a0a3000 CR4: 00000000000006e0
Stack:
ffff880329eee758 ffff880329eee758 ffff88032a0678a8 ffffffff80502dad
ffff8800ba167978 ffff880329eee758 ffff88032bf9c520 ffff8800ba167978
ffff88032bf9c520 ffff88032bf9a290 ffff88032a0678b8 ffffffff80506909
Call Trace:
[<ffffffff80502dad>] ata_scsi_translate+0x3d/0x1b0
[<ffffffff80506909>] ata_sas_queuecmd+0x149/0x2a0
[<ffffffffa0046650>] sas_queuecommand+0xa0/0x1f0 [libsas]
[<ffffffff804ea544>] scsi_dispatch_cmd+0xd4/0x1a0
[<ffffffff804eb50f>] scsi_queue_rq+0x66f/0x7f0
[<ffffffff803e5098>] __blk_mq_run_hw_queue+0x208/0x3f0
[<ffffffff803e54b8>] blk_mq_run_hw_queue+0x88/0xc0
[<ffffffff803e5c74>] blk_mq_insert_request+0xc4/0x130
[<ffffffff803e0b63>] blk_execute_rq_nowait+0x73/0x160
[<ffffffffa0023fca>] sg_common_write+0x3da/0x720 [sg]
[<ffffffffa0025100>] sg_new_write+0x250/0x360 [sg]
[<ffffffffa0025feb>] sg_write+0x13b/0x450 [sg]
[<ffffffff8032ec91>] vfs_write+0xd1/0x1b0
[<ffffffff8032ee54>] SyS_write+0x54/0xc0
[<ffffffff80689932>] system_call_fastpath+0x12/0x17
tj: updated description.
Fixes: 12cb5ce101 ("libata: use blk taging")
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block driver changes from Jens Axboe:
"This contains:
- The 4k/partition fixes for brd from Boaz/Matthew.
- A few xen front/back block fixes from David Vrabel and Roger Pau
Monne.
- Floppy changes from Takashi, cleaning the device file creation.
- Switching libata to use the new blk-mq tagging policy, removing
code (and a suboptimal implementation) from libata. This will
throw you a merge conflict, since a bug in the original libata
tagging code was fixed since this code was branched. Trivial.
From Shaohua.
- Conversion of loop to blk-mq, from Ming Lei.
- Cleanup of the io_schedule() handling in bsg from Peter Zijlstra.
He claims it improves on unreadable code, which will cost him a
beer.
- Maintainer update or NDB, now handled by Markus Pargmann.
- NVMe:
- Optimization from me that avoids a kmalloc/kfree per IO for
smaller (<= 8KB) IO. This cuts about 1% of high IOPS CPU
overhead.
- Removal of (now) dead RCU code, a relic from before NVMe was
converted to blk-mq"
* 'for-3.20/drivers' of git://git.kernel.dk/linux-block:
xen-blkback: default to X86_32 ABI on x86
xen-blkfront: fix accounting of reqs when migrating
xen-blkback,xen-blkfront: add myself as maintainer
block: Simplify bsg complete all
floppy: Avoid manual call of device_create_file()
NVMe: avoid kmalloc/kfree for smaller IO
MAINTAINERS: Update NBD maintainer
libata: make sata_sil24 use fifo tag allocator
libata: move sas ata tag allocation to libata-scsi.c
libata: use blk taging
NVMe: within nvme_free_queues(), delete RCU sychro/deferred free
null_blk: suppress invalid partition info
brd: Request from fdisk 4k alignment
brd: Fix all partitions BUGs
axonram: Fix bug in direct_access
loop: add blk-mq.h include
block: loop: don't handle REQ_FUA explicitly
block: loop: introduce lo_discard() and lo_req_flush()
block: loop: say goodby to bio
block: loop: improve performance via blk-mq
Hans de Goede