s390s arch_setup_msi_irqs function ensures that we don't return with
more irqs than the PCI architecture allows and that a single PCI
function doesn't consume more irqs than the kernel is configured for.
At least the last check doesn't help much and should take the sum of
all irqs into account. Since that's already done by irq_alloc_desc
we can remove this check.
As for the first check we should use the value provided by the
firmware which can be less than what the PCI architecture allows.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This changes the default IOTLB flushing method to lazy flushing, which
means that there will be no direct flush after each DMA unmap operation.
Instead, the iommu bitmap pointer will be adjusted after unmap, so that
no DMA address will be re-used until after an iommu bitmap wrap-around.
The only IOTLB flush will then happen after each wrap-around.
A new kernel parameter "s390_iommu=" is also introduced, to allow changing
the flushing behaviour to the old strict method.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KMSG_COMPONENT has to be defined instead of COMPONENT.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MSI irqchip in s390 has its own mask and unmask MSI irq
functions, zpci_enable_irq() and zpci_disable_irq().
They mask and unmask MSI irq in standard ways, no arch
special. MSI driver provides two global standard functions
mask_msi_irq() and unmask_msi_irq(). Local zpci_enable_irq()
and zpci_disable_irq() are almost the same as the standard
two. the difference is local mask/unmask functions
read the mask status before mask and unmask everytime.
Then change the value and rewrite to hardware. In standard
functions, save the mask status after mask and unmask msi
irq, and use the cached status to change the mask status.
When we mask or unmask a MSI irq, we always cache its
mask status except we know need not to cache it, like in
pci_msi_shutdown. So use the standard functions to replace
the local is safe.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
[sebott: fixed inverted function pointers]
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull core irq updates from Thomas Gleixner:
"The irq department delivers:
- Another tree wide update to get rid of the horrible create_irq
interface along with its even more horrible variants. That also
gets rid of the last leftovers of the initial sparse irq hackery.
arch/driver specific changes have been either acked or ignored.
- A fix for the spurious interrupt detection logic with threaded
interrupts.
- A new ARM SoC interrupt controller
- The usual pile of fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding
irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller
genirq: Improve documentation to match current implementation
ARM: iop13xx: fix msi support with sparse IRQ
genirq: Provide !SMP stub for irq_set_affinity_notifier()
irqchip: armada-370-xp: Move the devicetree binding documentation
irqchip: gic: Use mask field in GICC_IAR
genirq: Remove dynamic_irq mess
ia64: Use irq_init_desc
genirq: Replace dynamic_irq_init/cleanup
genirq: Remove irq_reserve_irq[s]
genirq: Replace reserve_irqs in core code
s390: Avoid call to irq_reserve_irqs()
s390: Remove pointless arch_show_interrupts()
s390: pci: Check return value of alloc_irq_desc() proper
sh: intc: Remove pointless irq_reserve_irqs() invocation
x86, irq: Remove pointless irq_reserve_irqs() call
genirq: Make create/destroy_irq() ia64 private
tile: Use SPARSE_IRQ
tile: pci: Use irq_alloc/free_hwirq()
...
Add a bunch of s390 specific pci attributes to help
identifying pci functions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the driver core handle attribute creation by putting all s390
specific pci attributes in an attribute group which is referenced
by pdev->dev.groups in pcibios_add_device.
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the zpci_attr macro to create read only sysfs attributes
to avoid duplicate code.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Processing pci hotplug events can fail when a pci function is in an
unexpected state. This can happen when we already processed the
change associated with the hotplug event (especially when receiving
hotplug events during early boot).
Just ignore the event in this case.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
alloc_irq_desc() returns an integer and as documented either a valid
irq number or a negative error code. Checking for NO_IRQ is definitely
not the proper error handling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Link: http://lkml.kernel.org/r/20140507154339.409085048@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
Pull s390 updates from Martin Schwidefsky:
"There are two memory management related changes, the CMMA support for
KVM to avoid swap-in of freed pages and the split page table lock for
the PMD level. These two come with common code changes in mm/.
A fix for the long standing theoretical TLB flush problem, this one
comes with a common code change in kernel/sched/.
Another set of changes is Heikos uaccess work, included is the initial
set of patches with more to come.
And fixes and cleanups as usual"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (36 commits)
s390/con3270: optionally disable auto update
s390/mm: remove unecessary parameter from pgste_ipte_notify
s390/mm: remove unnecessary parameter from gmap_do_ipte_notify
s390/mm: fixing comment so that parameter name match
s390/smp: limit number of cpus in possible cpu mask
hypfs: Add clarification for "weight_min" attribute
s390: update defconfigs
s390/ptrace: add support for PTRACE_SINGLEBLOCK
s390/perf: make print_debug_cf() static
s390/topology: Remove call to update_cpu_masks()
s390/compat: remove compat exec domain
s390: select CONFIG_TTY for use of tty in unconditional keyboard driver
s390/appldata_os: fix cpu array size calculation
s390/checksum: remove memset() within csum_partial_copy_from_user()
s390/uaccess: remove copy_from_user_real()
s390/sclp_early: Return correct HSA block count also for zero
s390: add some drivers/subsystems to the MAINTAINERS file
s390: improve debug feature usage
s390/airq: add support for irq ranges
s390/mm: enable split page table lock for PMD level
...
The generic pci_enable_resources() does essentially the same thing as the
code in the s390 version of pcibios_enable_device().
There are differences, but I don't think any of them are a problem. The
generic code:
- Checks everything up to PCI_NUM_RESOURCES, not PCI_BAR_COUNT (6), so
we'll now check the ROM resource, IOV resources, and bridge windows.
- Checks for res->flags & IORESOURCE_UNSET. The s390 code never sets
IORESOURCE_UNSET, so this isn't a problem.
- Checks res->parent. The s390 pcibios_add_device() calls
pci_claim_resource() on all BARs (except ROM, IOV, and bridge windows)
so this isn't a problem either.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
The maximum usable buffer size of the s390 debug feature (when using
the sprintf_view) is 11 * sizeof(long) (1 pointer for the format
string + 10 arguments). When a larger buffer size is specified the
additional memory is unused and wasted per debug entry. So reducing
the buffer size to its maximum (or to the actual buffer size used)
will make more precious debug feature space usable.
For pci_msg, chsc_msg, and cio_crw we use the additional usable dbf
space to reduce the number of allocated pages.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The boundary size for iommu_area_alloc() is currently set to a constant
value. This is wrong, we shouldn't use a constant value but rather the
return value of dma_get_seg_boundary(), since a device driver can override
the default.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
driver-core now supports synchrnous self-deletion of attributes and
the asynchrnous removal mechanism is scheduled for removal. Use it
instead of device_schedule_callback().
* Conversions in arch/s390/pci/pci_sysfs.c and
drivers/s390/block/dcssblk.c are straightforward.
* drivers/s390/cio/ccwgroup.c is a bit more tricky because
ccwgroup_notifier() was (ab)using device_schedule_callback() to
purely obtain a process context to kick off ungroup operation which
may block from a notifier callback.
Rename ccwgroup_ungroup_callback() to ccwgroup_ungroup() and make it
take ccwgroup_device * instead. The new function is now called
directly from ccwgroup_ungroup_store().
ccwgroup_notifier() chain is updated to explicitly bounce through
ccwgroup_device->ungroup_work. This also removes possible failure
from memory pressure.
Only compile-tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull s390 updates from Martin Schwidefsky:
"The bulk of the s390 updates for v3.14.
New features are the perf support for the CPU-Measurement Sample
Facility and the EP11 support for the crypto cards. And the normal
cleanups and bug-fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (44 commits)
s390/cpum_sf: fix printk format warnings
s390: Fix misspellings using 'codespell' tool
s390/qdio: bridgeport support - CHSC part
s390: delete new instances of __cpuinit usage
s390/compat: fix PSW32_USER_BITS definition
s390/zcrypt: add support for EP11 coprocessor cards
s390/mm: optimize randomize_et_dyn for !PF_RANDOMIZE
s390: use IS_ENABLED to check if a CONFIG is set to y or m
s390/cio: use device_lock to synchronize calls to the ccwgroup driver
s390/cio: use device_lock to synchronize calls to the ccw driver
s390/cio: fix unlocked access of online member
s390/cpum_sf: Add flag to process full SDBs only
s390/cpum_sf: Add raw data sampling to support the diagnostic-sampling function
s390/cpum_sf: Filter perf events based event->attr.exclude_* settings
s390/cpum_sf: Detect KVM guest samples
s390/cpum_sf: Add helper to read TOD from trailer entries
s390/cpum_sf: Atomically reset trailer entry fields of sample-data-blocks
s390/cpum_sf: Dynamically extend the sampling buffer if overflows occur
s390/pci: reenable per default
s390/pci/dma: fix accounting of allocated_pages
...
When using the CLP interface to enable or disable a pci device a
valid function handle needs to be delivered. So far our assumption
was that we always have an up-to-date version of the function handle
(since it doesn't change when the device is in use). This assumption
is incorrect if the pci device is enabled or disabled outside of our
control. When we are notified about such a change we already receive
the new function handle. Just use it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch_setup_msi_irqs() hook can only be called from the generic MSI code
which ensures correct MSI type parameter.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Multiple MSIs have never been supported on s390 architecture, but the
platform code fails to report single MSI only.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
HW, FW and Linux support is in a better shape now - let's reenable
pci bus probing per default.
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
allocated_pages sometimes are increased even if s390_dma_alloc fails
also this value is never decreased even if s390_dma_free is called.
This patch fixes these bugs.
Also remove the atomic64_t casts (the members are already of this type).
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we receive a notification that a pci function became unavailable we clean
up by removing the pci device. This can confuse the driver since the function
is already unaccessible. Improve this situation by setting an appropriate
error_state.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we remove a pci bus after receiving a hotplug notification we need
to check if the bus is actually present (creation of the pci bus
during an earlier notification may have been failed).
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Initialization and scanning of the pci bus is omitted on older
machines without pci support or if pci=off was specified. Remember
the fact that we ran without pci support and prevent further bus
scans during resume from hibernate or after receiving hotplug
notifications.
Reported-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the availability of a pci function has changed by means
outside of our control we receive an availability event.
Implement/improve the handling of these notifications.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement pcibios_remove_bus to free arch specific data when a pci
bus is deregistered. While at it remove a useless kzalloc/kfree
wrapper.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup the functions for allocation and setup of bus resources. Do
not allocate the same name for each resource but use a per-bus name.
Also provide means to cleanup all resources allocated by a bus.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup function information block used as a modify pci function
parameter. Change reserved members to be anonymous. Fix the size
of the struct and add proper alignment information. Also put the
FIB on the stack.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup arch specific pci messages. Remove unhelpful messages and
replace others with entries in the debugfs.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement architecture-specific functionality when a PCI device is
doing a hibernate transition.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The bitmap used to mark dma mappings can be quite large on systems
with huge amounts of memory. Use virtual memory for this bitmap.
Suggested-by: Alexander Schmidt <alexschm@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Function handles may change while the system was in hibernation
use list pci functions and update the function handles.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In rare situations a PCI function can report a busy condition
when we issue the modify pci function command. A temporary busy
condition can exceed 1 second but not 2 seconds. Increase the
time until we report an error to 2 seconds. Also increase the
time we sleep between the retries to reduce the load in this
case.
Suggested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
List pci functions is used to query and iterate over pci functions.
This function currently has 2 users - initial device discovery and
rescan after a machine check. Instead of having a multipurpose
function pass a callback which gets called for each pci function.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an arch specific attribute to recover a pci function from an
error state or config space blockage.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use pci_claim_resource to find and request bus ressources in
pcibios_add_device. Also move some (de)initialization stuff to
pcibios_enable_device/pcibios_disable_device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert s390' pci hotplug to be builtin only, with no module option.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the introduction of PCI it became apparent that s390 should
convert to generic hardirqs as too many drivers do not have the
correct dependency for GENERIC_HARDIRQS. On the architecture
level s390 does not have irq lines. It has external interrupts,
I/O interrupts and adapter interrupts. This patch hard-codes all
external interrupts as irq #1, all I/O interrupts as irq #2 and
all adapter interrupts as irq #3. The additional information from
the lowcore associated with the interrupt is stored in the
pt_regs of the interrupt frame, where the interrupt handler can
pick it up. For PCI/MSI interrupts the adapter interrupt handler
scans the relevant bit fields and calls generic_handle_irq with
the virtual irq number for the MSI interrupt.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of the adapter interrupt helpers in the PCI code. This is
the first step to convert the MSI interrupt code to PCI domains.
The patch removes the limitation of 64 adapter interrupts per
PCI function.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are three users of adapter interrupts: AP, QDIO and PCI. Each
registers a single adapter interrupt with independent ISCs. Define
a "struct airq" with the interrupt handler, a pointer and a mask for
the local summary indicator and the ISC for the adapter interrupt
source. Convert the indicator array with its fixed number of adapter
interrupt sources per ISE to an array of hlists. This removes the
limitation to 32 adapter interrupts per ISC and allows for arbitrary
memory locations for the local summary indicator.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The per-pci-device 'debug' attribute is ill defined. For each device
it prints the same information, the adapter interrupt bit vector for
irq numbers 0 & 1, the start of the global interrupt summary vector
and the global irq retries counter. Just remove the attribute and
the associated code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of the strlen calls, use the return value of sprintf instead.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The disable slot implementation on s390 currently just detaches the
pci function from the partition - without informing the pci layer.
Fix this by calling pci_stop_and_remove_bus_device prior to the
operation.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide wrappers for the [de]configure operations, add some error
handling, and use pci_scan_slot instead of pci_scan_single_device.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use pcibios_release_device to implement architecture-specific
functionality when a pci device is released. This function
will be called during pci_release_dev.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the to_pci_dev macro to fetch a pci_dev from a struct device
pointer.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All architectures must implement IRQ functions. Since various
dependencies on !S390 were removed, there are various drivers that can
be selected but will fail to link. Provide a dummy implementation of
these functions for the !PCI case.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org # 3.9
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The pci config space accessors on s390 are (now) smart enough to
figure out if a pci function is available. So instead of calling
pci_create_root_bus and then pci_scan_single_device for each
available function just call pci_scan_root_bus and let the pci core
do the scanning (via config reads on all possible functions) and
device creation.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For offset > PAGE_SIZE, s390_dma_map_pages() will issue a warning
and return a wrong dma address.
This patch removes the warning and fixes the dma return address
calculation.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pci_disable_device is called by a driver after it stops using the pci
function - e.g. during the removal of the driver. The current
implementation removes the architecture specific information of this
function such that even after a call to pci_enable_device the pci
function is no longer usable. Just remove pcibios_disable_device.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disable pci on s390. Enable with pci=on.
Suggested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Access to pci config space via pci_ops should not fail silently.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a pci load instruction fails the content of the register where the
data is stored is possibly unchanged. Fix the inline assembly wrapper
__pcilg to not return stale data. Additionally fix the callers of this
function who access uninitialized variables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't let pci_load and friends crash the kernel when called with
e.g. an invalid offset. Return -ENXIO instead.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use distinct (and hopefully sane) names for the pci instruction
wrappers.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Uninline pci related instruction wrappers to de-bloat the code:
add/remove: 15/0 grow/shrink: 2/24 up/down: 1326/-12628 (-11302)
This is especially useful for the inlined pci read and write functions
which are used all over the kernel. Also remove the unused __stpcifc
while at it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use pcibios_add_device to do arch specific device initialization.
This function will be called during pci_bus_add_device.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't modify function handles to get a disabled handle - call
clp_disable_fh. With this change we also do no longer deconfigure
enabled functions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the debugfs to keep track of a pci function's status changes.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The hash used for mapping irq numbers to msi descriptors does not
utilize all buckets that were allocated. Fix this by using the same
value (computed by the number of bits used for the hash function) at
relevant places.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Loading the pci hotplug module when no devices are present will fail
but unfortunately some hotplug callbacks stay registered to the pci
bus level. Fix this by not letting module loading fail when no pci
devices are present and provide proper {de}registration functions
for these callbacks.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the __get_free_pages wrapper in clp_alloc_block. Also change the
allocation to use one page only. This page is used as CLP response
block e.g. to list available pci functions. Using one page we can
list > 250 pci functions at once and we have code to loop around this
CLP command (if not all functions fit into to the CLP block) already
in place.
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tell gcc that the memory region pointed to by req will be used (and
changed). Also remove the (now) superfluous memory constraint.
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pci_probe is too generic and has a name clash with other common code parts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that irq sum accounting for /proc/stat's "intr" line works again we
have the oddity that the sum field (first field) contains only the sum
of the second (external irqs) and third field (I/O interrupts).
The reason for that is that these two fields are already sums of all other
fields. So if we would sum up everything we would count every interrupt
twice.
This is broken since the split interrupt accounting was merged two years
ago: 052ff461c8 "[S390] irq: have detailed
statistics for interrupt types".
To fix this remove the split interrupt fields from /proc/stat's "intr"
line again and only have them in /proc/interrupts.
This restores the old behaviour, seems to be the only sane fix and mimics
a behaviour from other architectures where /proc/interrupts also contains
more than /proc/stat's "intr" line does.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/pci/pci_dma.c:16:29: warning: ‘zpci_ioat_dt’ defined but not used [-Wunused-variable]
arch/s390/pci/pci.c:164:12: warning: ‘zpci_store_fib’ defined but not used [-Wunused-function]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes up all of the smaller arches that had __dev* markings for
their platform-specific drivers.
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for reading the PCI function measurement block counters
provided by the hypervisor. Add two s390 debug features, one for
critical errors and one for tracing and provide wrappers to log data.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Benefit from pci store block instruction by writing up to 128 bytes
with a single instruction to MMIO space. Depending on the workload
this can result in a huge performance increase due to the reduced
number of instructions. The ordering guarantees of single stores
vs. one store block are identical.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dereference to 'zdev' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some s390 specific sysfs attributes to the PCI device directory.
The following attributes are introduced:
- function_id (PCI function ID)
- function_handle (PCI function handle)
- pchid (PCI channel ID)
- pfgid (PCI function group ID aka PCI root complex)
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add DMA IOMMU support using 4K page table entries. Implement dma_map_ops.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.
Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CLP instructions are used to query the firmware about detected PCI
functions, the attributes of those functions and to enable or disable
a PCI function. The CLP interface is the equivalent to a PCI bus scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add PCI support for s390, (only 64 bit mode is supported by hardware):
- PCI facility tests
- PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit
- map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions
- pci_iomap implementation
- memcpy_fromio/toio
- pci_root_ops using special pcilg/pcistg
- device, bus and domain allocation
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>