For SRIOV based adapters, driver should not set the STOP_ADP bit as part of
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Invader series, if FW supports more than 8 MSI-x vectors, driver needs
to enable combined reply queue mode. For Ventura series, driver enables
combined reply queue mode in case of more than 16 MSI-x vectors.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Module parameter description for rdpq_enable incorrectly lists the default
as enabled. Also, provide range of valid values for resetwaittime in the
description.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During init, if pci_alloc_irq_vectors() fails, the driver has not yet setup
the IRQs. Fix the goto labels and error handling for this case.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change copyright to Broadcom Inc. Also update any references to Avago with
Broadcom. Update copyright duration wherever required.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SAS3 and later controllers, FW sets the reset adapter bit indicating
the driver to perform a controller reset. Driver needs to check if this
bit is set before doing a reset. This reduces the driver probe failure
time to 180seconds in case there is a faulty controller connected.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_transition_to_ready() driver waits 180seconds for controller to
change FW state. Here we are calling msleep(1) in a loop for this. As
explained in timers-howto.txt, msleep(1) will actually sleep longer than
1ms. If a faulty controller is connected, we will end up waiting for much
more than 180 seconds causing unnecessary delays during load.
Change the granularity of msleep() call from 1ms to 1000ms.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Latest firmware adds a mechanism to save firmware logs just before
controller reset on pre-allocated internal controller DRAM. This feature is
called snapdump which will help debugging firmware issues. This feature
requires extra time and firmware reports these values through new driver
interface. Before initiating an OCR, driver needs to inform FW to save a
snapdump and then wait for a specified time for the snapdump to complete.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver checks for Firmware state change from ISR context, and
only when there are interrupts tied with no I/O completions. We have seen
multiple cases where doorbell interrupts sent by firmware to indicate FW
state change are not processed by driver and it takes long time for driver
to trigger OCR. And if there are no IOs running, since we only check the FW
state as part of ISR code, fault goes undetected by driver and OCR will not
be triggered.
This patch introduces a separate workqueue that runs every one second to
detect Firmware FAULT state and trigger reset immediately. As an
additional gain, removing PCI reads from ISR to check FW state results in
improved performance as well.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_reset_handler':
drivers/scsi/megaraid/megaraid_mbox.c:2580:7: warning:
variable 'recovering' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'mbox_post_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:2728:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_support_random_del':
drivers/scsi/megaraid/megaraid_mbox.c:3138:11: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_flush_cache':
drivers/scsi/megaraid/megaraid_mbox.c:3266:10: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_fire_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:3302:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'gather_hbainfo':
drivers/scsi/megaraid/megaraid_mbox.c:3797:10: warning:
variable 'dmajor' set but not used [-Wunused-but-set-variable]
[mkp: applied by hand due to conflict with hch's DMA cleanup]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_mgmt_compat_ioctl_fw(), to handle the structure
compat_megasas_iocpacket 'cioc', a user-space structure megasas_iocpacket
'ioc' is allocated before megasas_mgmt_ioctl_fw() is invoked to handle
the packet. Since the two data structures have different fields, the data
is copied from 'cioc' to 'ioc' field by field. In the copy process,
'sense_ptr' is prepared if the field 'sense_len' is not null, because it
will be used in megasas_mgmt_ioctl_fw(). To prepare 'sense_ptr', the
user-space data 'ioc->sense_off' and 'cioc->sense_off' are copied and
saved to kernel-space variables 'local_sense_off' and 'user_sense_off'
respectively. Given that 'ioc->sense_off' is also copied from
'cioc->sense_off', 'local_sense_off' and 'user_sense_off' should have the
same value. However, 'cioc' is in the user space and a malicious user can
race to change the value of 'cioc->sense_off' after it is copied to
'ioc->sense_off' but before it is copied to 'user_sense_off'. By doing
so, the attacker can inject different values into 'local_sense_off' and
'user_sense_off'. This can cause undefined behavior in the following
execution, because the two variables are supposed to be same.
This patch enforces a check on the two kernel variables 'local_sense_off'
and 'user_sense_off' to make sure they are the same after the copy. In
case they are not, an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dma_map_sg / dma_unmap_sg APIs called from scsi_dma_map /
scsi_dma_unmap already transfer memory ownership to the device or cpu
respectively. Adding additional calls to pci_dma_sync_sg_* will in fact
lead to data corruption if we end up using swiotlb for some reason.
Also remove the now pointless megaraid_mbox_sync_scb function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in warning message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware provides drive specific target reset and task abort timeout
values. Driver needs to use these timeout values during task management
calls. If FW does not provide these values, fall back to using earlier
default timeout of 50 seconds for TM.
[mkp: clarified comment]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While driver is waiting for adapter to become operational, if a kill
adapter is issued, driver can bail out from the wait loop immediately
rather than waiting for the entire 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If MR_DCMD_CTRL_GET_INFO DCMD timed out, return failure rather than doing
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
The BLK_EH_NOT_HANDLED implies nothing happen, but very often that
is not what is happening - instead the driver already completed the
command. Fix the symbolic name to reflect that a little better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 2d2c233167 ("scsi: megaraid_sas: modified few prints in OCR and IOC INIT path")
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Acked-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hardware could time out Fastpath IOs one second earlier than the timeout
provided by the host.
For non-RAID devices, driver provides timeout value based on OS provided
timeout value. Under certain scenarios, if the OS provides a timeout
value of 1 second, due to above behavior hardware will timeout
immediately.
Increase timeout value for non-RAID fastpath IOs by 1 second.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use pci_zalloc_consistent for allocating zeroed memory and remove
unnecessary memset function.
Done using Coccinelle.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas. In addition we have removed several really
old drivers: sym53c416, NCR53c406a, fdomain, fdomain_cs and removed
the old scsi_module.c initialization from all remaining drivers. Plus
an assortment of bug fixes, initialization errors and other minor
fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWsVSnSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbvbAP9ErpTZ
OR5iJ5HIz4W3Bd8aTfEpJrDyeYwSUC+sra5SKQD/ZWyVB3fYFSg+ZROyT26pmtmd
SdImhG7hLaHgVvF5qRQ=
=SQ/n
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew. The
remaining 5 patches all try to fix commit 84676c1f21
"genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWrpSmyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishY+MAP9Zvin/
AUc3xkvOPdIzRPp2aXQHJKC+NGmNFr6MiXIHiAD/TvjbkxEjbUTjnr+gZNaloDma
d/I4i9xaBNSvqNJpzT0=
=mLIX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew.
The remaining five patches all try to fix commit 84676c1f21
("genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi_tcp: set BDI_CAP_STABLE_WRITES when data digest enabled
scsi: sd: Remember that READ CAPACITY(16) succeeded
scsi: ibmvfc: Avoid unnecessary port relogin
scsi: virtio_scsi: unify scsi_host_template
scsi: virtio_scsi: fix IO hang caused by automatic irq vector affinity
scsi: core: introduce force_blk_mq
scsi: megaraid_sas: fix selection of reply queue
scsi: hpsa: fix selection of reply queue
Since commit 84676c1f21 ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.
Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Fixes: 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch is mostly fixes for driver specific issues (nine of them)
and the storvsc performance improvement with interrupt handling which
was dropped from the previous fixes pull request. We also have two
regressions: one is a double call_rcu() in ATA error handling and the
other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte().
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWp7/dCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSYAAP0RiYSR
oq3yLesh09tx0u+w2He8ylpdVizIzNMTjNE+BAD9GqeQWEvNaoGPUwNeMFJuwawX
hNjOttF1YOfFlsuoG94=
=9e1j
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is mostly fixes for driver specific issues (nine of them) and the
storvsc performance improvement with interrupt handling which was
dropped from the previous fixes pull request.
We also have two regressions: one is a double call_rcu() in ATA error
handling and the other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte()"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Fix kernel crash during port toggle
scsi: qla2xxx: Fix FC-NVMe LUN discovery
scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()
scsi: core: Avoid that ATA error handling can trigger a kernel hang or oops
scsi: qla2xxx: ensure async flags are reset correctly
scsi: qla2xxx: do not check login_state if no loop id is assigned
scsi: qla2xxx: Fixup locking for session deletion
scsi: qla2xxx: Fix NULL pointer crash due to active timer for ABTS
scsi: mpt3sas: wait for and flush running commands on shutdown/unload
scsi: mpt3sas: fix oops in error handlers after shutdown/unload
scsi: storvsc: Spread interrupts when picking a channel for I/O requests
scsi: megaraid_sas: Do not use 32-bit atomic request descriptor for Ventura controllers
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement: Sending I/O through 32 bit descriptors to Ventura series of
controller results in IO timeout on certain conditions.
This error only occurs on systems with high I/O activity on Ventura series
controllers.
Changes in this patch will prevent driver from using 32 bit descriptor and use
64 bit Descriptors.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas. We also have a rework of the libsas hotplug handling to
make it more robust, a slew of 32 bit time conversions and fixes, and
a host of the usual minor updates and style changes. The biggest
potential for regressions is the libsas hotplug changes, but so far
they seem stable under testing.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnH+5SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWxuAP0UvuJp
MNR/yU/wv/emSzOc48Ldwd7I0xD2XxSnloGUgwD+IGZZT5yNUQA1THCbm+en4hkB
WvyBieQs9qRit+2czd4=
=gJMf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
NVMe passthrough via MFI interface. Current MegaRAID product supports
different types of encapsulation via the MFI framework.
NVMe native command should be framed by application and it should be
embedded in MFI as payload. The driver will provide interface to send
the MFI frame along with the payload (in this case, payload is NVMe
native command) to the firmware. Driver already has an existing, similar
interface for SATA and SMP passthrough.
1. Driver will pass MFI command to the firmware if the latter supports
NVMe encapsulated processing (not all SAS3.5 firmware supports this
feature).
2. Driver exposes sysfs entry support_nvme_encapsulation. This is
required for backward compatibility for applications using earlier
driver versions that did not process IOCTL frames and could result in
host hang.
This is already fixed as part of commit 82add4e1b3 ("scsi:
megaraid_sas: Incorrect processing of IOCTL frames for SMP/STP
commands")
[mkp: clarified commit message]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
do_gettimeofday() overflows in 2038 on 32-bit architectures and is
deprecated, so convert this driver to call ktime_get_real()
directly. This also simplifies the calculation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional changes.
This patch is a re-work of DCMD refire code to better manage all the
different cases to decide whether to REFIRE or SKIP or COMPLETE certain
DCMD.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose FW outstanding commands (fw_outstanding) through sysfs interface.
This helps in debugging certain performance issues in the field.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance improvement:
Current driver calls stream detection unconditionally for all IOs.
Stream Detection logic is not required for most of the fast path IO. To
improve performance, avoid stream detection logic and do it only if
required.
Below are the cases where stream detection is required in driver:
1. All non-FastPath IOs (IOs going to FW)
2. Fast Path reads sent to ReadAhead capable VDs.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue – There may be some IO accessing incorrect raid map, but driver
has checks in IO path to handle those cases. It is always better to move
to new raid map only once raid map is populated and validated. No
functional defect. Fix is provided as part of review. Fix – Update
instance->map_id after driver has populated new driver raid map from
firmware raid map.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In IOCTL path, re-use megasas_wait_for_adapter_operational API to detect
controller state. This will make driver to use this API uniformly in all
cases where we need to wait for adapter to become operational.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver needs to avoid PCI writes while OCR is in progress. Use
reset_mutex to synchronize between firing DCMDs MR_DCMD_PD_GET_INFO and
MR_DCMD_DRV_GET_TARGET_PROP while OCR is triggered. Without this fix,
if Device/VD add/creation is in progress and at the same time MR
Firmware is going through OCR, user may see OCR never completed and it
may need system reboot. This scenario is rare to occur. Fix is provided
as part of review.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue - Driver returns DID_NO_CONNECT when unload is in progress,
indicated using instance->unload flag. In case of dynamic unload of
driver, this flag is set before calling scsi_remove_host(). While doing
manual driver unload, user will see lots of prints for Sync Cache
command with DID_NO_CONNECT status.
Fix - Set the instance->unload flag after scsi_remove_host(). Allow
device removal process to be completed and do not block any command
before that. SCSI commands (like SYNC_CACHE) are received (as part of
scsi_remove_host) by driver during unload will be submitted further down
to the drives.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver does not validate ldcount provided by firmware. If the
value is invalid, fail RAID map validation accordingly. This issue is
rare to hit in field and is fixed as part of code review.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_get_seq_num, the status of the DCMD fired to FW is not
returned, it always returns success. We could end up registering AEN
request with incorrect sequence number if the DCMD failed. Return the
DCMD status back to caller. This was discovered during code review and
very rare to see issue in field to see AEN request failed bt FW.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit b9637d14dc ("scsi: megaraid_sas: Resize MFA frame used for IOC
INIT to 4k") increased the size of IOC INIT frame to 4k. Need to use
updated size when memsetting init_frame.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memory allocated for IOC_INIT command and stream detection array are not
zero'd before using. Use kzalloc instead of kmalloc to zero out the
memory allocated.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Trivial fix to spelling mistake in dev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_alloc_cmds is to alloc cmd_list of instance instead of fusion,
and fusion is useless in this function. Just remove it.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also consolidates the timer setup
functions arguments, which are all identical, and corrects on-stack timer
usage.
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The latest MegaRAID Firmware (for Invader series) has support for 64bit
DMA for both streaming and consistent DMA buffers. All Ventura series
controller FW always support 64 bit consistent DMA. Also, on a few
architectures 32bit DMA is not supported.
Current driver always prefers 32bit for consistent DMA and 64bit for
streaming DMA. This behavior was unintentional and carried forwarded
from legacy controller FW. Need to enhance the driver to support 64bit
consistent DMA buffers based on the firmware capability.
Below is the DMA setting strategy in driver with this patch. For
Ventura series, always try to set 64bit DMA mask. If it fails fall back
to 32bit DMA mask. For Invader series and earlier generation
controllers, first try to set to 32bit consistent DMA mask irrespective
of FW capability. This is needed to ensure firmware downgrades do not
break. If 32bit DMA setting fails, check FW capability and try seting to
64bit DMA mask.
There are certain restrictions in the hardware for having all sense
buffers and all reply descriptors to be in the same 4GB memory region.
This limitation is h/w dependent and can not be changed in firmware.
This limitation needs to be taken care in driver while allocating the
buffers. There was a discussion regarding this - find details at below
link. https://www.spinics.net/lists/linux-scsi/msg108251.html
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver load fails if memory allocation for request frame pool fails due
to the higher queue_depth requirement. The driver now allows dynamically
reducing queue_depth if memory allocations fail rather than failing
load. With this, there is no need to limit queue_depth to 1K.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain cases, the host memory is limited and with FW supporting
higher queue depths there are increasing chances of IO request frame
allocation failures that we are seeing. In case of request frame
allocation failures, retry allocation with reduced queue depth (in steps
of 64) to continue to configure the controller with a reduced
performance rather than failing load.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd->frame->dcmd.opcode will be valid only for MFI_CMD_DCMD
IOCTL frames. Currently driver check for cmd->frame->dcmd.opcode without
checking cmd type. Ensure we check dcmd opcode only for MFI_CMD_DCMD
commands. Separate handling of MFI_CMD_SMP/STP commands from
MFI_CMD_DCMD in completion path.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Older firmware version unconditionally pulls 4k frame for IOC INIT MFA
frame. But driver allocates 1k or 4k max_chain_frame_sz based on FW
capability. During boot time, this results in DMA read errors.
Workaround fix in driver by allocating separate ioc_init frame of 4k
size to support older firmware.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver needs to send current host time to firmware during init.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring, no functional change. Create new function to
initialize all the controller parameters during load time.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-use the pre-allocated ctrl_info DMA buffer.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pre-allocate few of the frequently used DMA buffers during load time.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring - create separate functions to allocate and free
controller DMA buffers
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactoring to improve readability. Move the
code to allocate and free controller memory into separate functions.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fusion_context structure is very large around 180kB and most of the size
is contributed by log_to_span array. Move log_to_span out of fusion
context and have separate allocation for log_to_span. And use kmalloc to
allocate fusion_context. Currently kmemleak reports 1000s of false
positives for fusion->cmd_list[]. kmemleak does not track page
allocation for fusion_context. This change will also fix the false
positives reported by kmemleak.
Ref: https://marc.info/?l=linux-scsi&m=150545293900917
Reported-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase code readability. No functional change.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for PCI VID/DID 0x1000/0x0015 based MegaRAID controllers.
Since the DID 0x0015 conflicts with DELL PERC5 controllers,
add vendor ID based check specific for DELL PERC5.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Refactor adapter_type to set for all generation controllers, not
just for fusion controllers.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megaraid_mbox only has one reset function, and that is a host reset. So
drop the duplicate bus reset and device reset functions.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang. Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In TM code, smid_task is valid only in case of task aborts.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds. If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to task abort case, use synchronize_irq API in target reset
case. Also, remove redundant call to megasas_complete_cmd_dpc_fusion
after calling megasas_sync_irqs in task abort case.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting resetwaittime to 0 during a FW fault will result in driver not
calling the OCR.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver allocated 256 byte MFI frames bytes but while sending MFI frame
(embedded inside chain frame of MPT frame) to firmware, driver sets the
length as 4k. This results in DMA read error messages during boot.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_mgmt_info.max_index has increased by 1 before megasas_io_attach,
if megasas_io_attach return error, then goto fail_io_attach,
megasas_mgmt_info.instance has a wrong index here. So first reduce
max_index and then set that instance to NULL.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix allocate instance->pd_info twice which was introduced by 96188a89cc.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's better to use the DRIVER_ATTR_RW() and DRIVER_ATTR_RO() macros to
explicitly show that this is a read/write or read/only sysfs file. So
convert the remaining SCSI drivers that use the old style to use the
newer macros.
Bonus is that this removes some checkpatch.pl warnings :)
This is part of a series to drop DRIVER_ATTR() from the tree entirely.
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver may sleep under a spin lock, and the function call path is:
mraid_mm_attach_buf (acquire the lock by spin_lock_irqsave)
pci_pool_alloc(GFP_KERNEL) --> may sleep
To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
[mkp: fixed whitespace]
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove an inline from a fairly big function that is used often. It's
unlikely that calling or not calling it makes a lot of difference.
Saves around 8k text in my kernel.
text data bss dec hex filename
9047801 5367568 11116544 25531913 1859609 vmlinux-before-megasas
9039417 5367568 11116544 25523529 1857549 vmlinux-megasas
Link: http://lkml.kernel.org/r/20170315021431.13107-7-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Kashyap Desai <kashyap.desai@avagotech.com>
Cc: Sumit Saxena <sumit.saxena@avagotech.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix, raid6 performance will not be optimal.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return value check of atomic_dec_if_positive is required as it returns
old value minus one. Without this fix, driver will send small ios to
firmware path and that will be a performance issue.
Not critical, but good to have r1_ldio_hint as default value in sdev
private.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.
lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required. See below lspci output. DisINTx is
set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with a dma_addr_t that is different from pointer size, we
get this warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1654:17: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
It's better to not pretend that the dma address is a pointer and instead
use a dma_addr_t consistently.
Fixes: 33203bc4d6 ("scsi: megaraid_sas: NVME fast path io support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "sz" variable is in terms of bytes, but we're treating the buffer as
an array of __le32 so we have to divide by 4.
Fixes: def0eab3af ("scsi: megaraid_sas: enhance debug logs in OCR context")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID1 FastPath writes, driver needs to allocate extra commands
internally to accommodate for the extra peer command being sent.
Currently driver is allocating 2 extra commands for each but only one
extra command is necessary. Set RAID_1_10_RMW_CMDS to 2 and also change
macro name to RAID_1_PEER_CMDS.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix indentation issues and smatch warning reported by Dan Carpenter
for previous series as discussed below.
http://www.spinics.net/lists/linux-scsi/msg103635.htmlhttp://www.spinics.net/lists/linux-scsi/msg103603.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix - increase internal command pool to 8.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FIX - Do not use random delay to synchronize with IRQ. Use kernel API.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error handling: Bail out the driver load if key FW cmds (LD_LIST) are
not return successful. Clean up error handling in megasas_init_fw.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring to build_mpt_mfi_pass_thru to return void.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error handling: If controller reset is not able to recover, kill HBA and
quit immediately.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FIX - firmware wants non-RW SYS PD IOs to avoid FastPath for better
tracking and other functionalities if the device is task management
capable.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memset the IO frame to zero after release.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to account for the reply_q_sz not exceeding the maximum commands
that the firmware can support, instance->max_fw_cmds is already
decremented in megasas_fusion_update_can_queue(). Remove the extra
decrement logic in code.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Minor Optimization: No need to update HBA can_queue value if the current
max FW commands is equal to earlier value.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since maximum supported FW commands are all defined as u16, change
all local variables referring to max_cmd from u32 to u16.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue is limited for Syncro firmware where pd_after_lb is not set but is
accidentally used. Not a functional issue, but results in low
performance due to improper load balancing between two LUNs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fetch the latest controller OCR capability from FW before sending
MR_DCMD_CTRL_SHUTDOWN When application sends a shutdown DCMD
(MR_DCMD_CTRL_SHUTDOWN), driver will fetch latest controller information
from firmware. This is to ensure that driver always has latest OCR
capability of controller before sending the DCMD.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel warning for accessing unaligned memory access in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix endiannes fixes for Ventura specific.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix if RDPQ mode enabled MR FW is deployed on big endian host machine,
driver does not setup reply address correctly.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change MR_TargetIdToLdGet return type from u8 to u16.
ld id range check is added at two places in this patch -
@megasas_build_ldio_fusion and @megasas_build_ld_nonrw_fusion. Previous
driver code used different data type for lds TargetId returned from
MR_TargetIdToLdGet. Prior to this change, above two functions was
safeguarded due to function always return u8 and maximum value of ld id
returned was 255.
In below check, fw_supported_vd_count as of today is 64 or 256 and valid
range to support is either 0-63 or 0-255. Ideally want to filter
accessing raid map for ld ids which are not valid. With the u16 change,
invalid ld id value is 0xFFFF and we will see kernel panic due to random
memory access in MR_LdRaidGet. The changes will ensure we do not call
MR_LdRaidGet if ld id is beyond size of ldSpanMap array.
if (ld < instance->fw_supported_vd_count)
>From firmware perspective,ld id 0xFF is invalid and even though current
driver code forward such command, firmware fails with target not
available.
ld target id issue occurs mainly whenever driver loops to populate raid
map (ea. MR_ValidateMapInfo). These are the only two places where we
may see out of range target ids and wants to protect raid map access
based on range provided by Firmware API.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a host, if an ld is deleted there is a hole in the ld array returned
by the FW. But in MR_ValidateMapInfo we are not accounting for holes in
the ld array and traverse only upto index num_lds. This patch takes
care of converting the capability field of all the valid lds in the ld
raid map.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently fusion context has fixed array load_balance_info. Use dynamic
allocation. In few places, driver do not want physically contigious
memory. Attempt to use vmalloc if physical contiguous memory is not
available.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add additional logging from driver in OCR context.
Add debug logs for partial completion of IOs is iodone context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixing issue of not setting residual bytes correctly.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid Host side PCI bandwidth bottleneck and hint FW to do Write
buffering using RaidFlag MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT. Once
IO is landed in FW with MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT, it will
do single DMA from host and buffer the Write operation. On back end, FW
will DMA same buffer to the Mirror and Data Arm. This will improve
large block IO performance which bottleneck due to Host side PCI
bandwidth limitation.
Consistent ~4000MB T.P for 256K Block size is expected performance
numbers. IOPS for small Block size should be on par with Disk
performance. (E.g 42 SAS Disk in JBOD mode gives 3700MB T.P. Same
Drive used in R1 WT mode, should give ~1800MB T.P)
Using this patch 24 R1 VDs (HDD) gives below performance for Sequential
Write. Without this patch, we cannot reach above 3200MB (Throughput is
in MB.)
Block Size 50% 256K and 50% 4K 100% 256K
4K 3100 2030
8K 3140 2740
16K 3140 3140
32K 3400 3240
64K 3500 3700
128K 3870 3870
256K 3920 3920
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provide true fast path IO support. Driver creates PRP for
NVME drives and send Fast Path for performance. Certain h/w requirement
needs to be taken care in driver.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fetch true values of NVME property from FW using New DCMD
interface MR_DCMD_DEV_GET_TARGET_PROP
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding detection logic for NVME device attached behind Ventura
controller. Driver set HostPageSize in IOC_INIT frame to inform about
page size for NVME devices. Firmware reports NVME page size to the
driver. PD INFO DCMD provide new interface type NVME_PD. Driver set
property of NVME device.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the changes to remove checks for a valid request descriptor,
issue_dcmd will now always return DCMD_SUCCESS. This patch changes
return type of issue_dcmd to void and change all callers appropriately.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code clean up. Removing error code which is not
valid scenario. In megasas_get_request_descriptor we can remove the
error handling which is not required. With fusion controllers, if there
is a valid message frame available, we are guaranteed to get a
corresponding request descriptor.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Moving to use DID_REQUEUE return type for reliable unconditional
retries. Driver wants unconditional re-queue, so replace DID_RESET with
DID_REQUEUE
Discussed below -
https://www.spinics.net/lists/linux-scsi/msg102848.html
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
megasas_fire_cmd_fusion can always use 32 bit descriptor write for
ventura. No need to pass extra flag. Only IOC INIT required 64 bit
Descriptor write.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
Remove function megasas_fpio_to_ldio as we never require to convert fpio
to ldio because of frame unavailability. Grab extra frame of raid 1
write fast path before it creates first frame as Fast Path. Removed
is_raid_1_fp_write flag as raid 1 write fast path command is decided
using r1_alt_dev_handle only. Move resetting megasas_cmd_fusion fields
at common function megasas_return_cmd_fusion.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactor.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit "3e5eadb1a881" ("scsi: megaraid_sas: Enable or
Disable Fast path based on the PCI Threshold Bandwidth")
This patch was aimed to increase performance of R1 Write operation for
large IO size. Since this method used timer approach, it turn on/off
fast path did not work as expected. Patch 0013 describes new algorithm
and performance number.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ldio outstanding variable needs to be decremented in io completion path for
iMR dual queue depth
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.
Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An UNMAP command on a PI formatted device will leave the Logical Block Application
Tag and Logical Block Reference Tag as all F's (for those LBAs that are unmapped).
To avoid IO errors if those LBAs are subsequently read before they are written with
valid tag fields, the MPI SCSI IO requests need to set the EEDPFlags element EEDP
Escape Mode field, Bits [7:6] appropriately. A value of 2 should be set to disable
all PI checks if the Logical Block Application Tag is 0xFFFF for PI types 1 and 2.
A value of 3 should be set to disable all PI checks if the Logical Block Application
Tag is 0xFFFF and the Logical Block Reference Tag is 0xFFFFFFFF for PI type 3.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
[mkp: fixed bad indentation]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is not good when an irq arrives before driver structures are
allocated.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A couple of dev_printk messages spans two lines and the literal string
is missing a white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will fix regression caused by commit 1e793f6fc0 ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
[mkp: clarified patch description]
Fixes: 1e793f6fc0
Reported-by: Jens Axboe <axboe@kernel.dk>
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: stable@vger.kernel.org
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.
There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.
Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.
New SYNCHRONIZE_CACHE behavior:
IF 'JBOD'
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver
ELSEIF 'VirtualDisk'
IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF
[mkp: edited patch description]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state. Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.
[mkp: fixed typos]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the issue of wrong PhysArm was sent to firmware for R1
VD downgrade.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
CC: stable@vger.kernel.org
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 02b01e010a ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010a
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (hpsa, be2iscsi,
hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi
for which a driver is added, there's some cleanup work of the ibm vscsi target
and updates to libfc, plus a whole host of minor fixes and updates and finally
the removal of several ISA drivers which seem not to have been used for years.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyTO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.
It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I actually read the error messages in my logs, and successful
initialization is not an error.
Arguably these log lines could be deleted entirely.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do code optmization for task management functions.
Below are key changes:
1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.
2. Create wrapper functions for task abort and target reset and inside
these functions adapter specific calls be made. e.g. fusion adapters
support task abort and target reset so task abort and target reset
should be issued to fusion adapters only and for MFI adapters, print
a message saying feature not supported.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 90dc9d98f0 ("megaraid_sas : MFI MPT linked list corruption fix")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so
if MFI adapters fail this DCMD, it should not be considered as FATAL and
driver should not issue kill adapter and set per controller's instance
variable- pd_list_not_supported so that same variable can be used inside
functions- slave_alloc and slave_configure to allow firmware scan.
Killing adapter because of DCMD failure when this DCMD is not supported
causes driver's probe getting failed. This issue got introduced by
commit 6d40afbc7d ("megaraid_sas: MFI IO timeout handling").
Killing adapter in case of this DCMD failure should be limited to Fusion
adapters only. Per controller's instance variable allow_fw_scan is
removed as pd_list_not_supported better reflect the purpose.
Fixes: 6d40afbc7d
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Inside compat IOCTL hook of driver, driver was using wrong address of
ioc->frame.raw which leads sense_ioc_ptr to be calculated wrongly and
failing IOCTL.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver assumes that VFs always have peers present whenever they have
same LD IDs. But this is not the case. This patch handles the above
mentioned by explicitly checking for a peer before making HA/non-HA path
decision.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pd_seq_sync pointer can't be NULL, we have to check its entries
instead.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes online controller resets on SRIOV-enabled series of
Avago controllers.
1) Remove late detection heartbeat.
2) Change in the behavior if the FW found in READY/OPERATIONAL state.
Signed-off-by: Uday Lingala <uday.lingala@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will introduce module-parameter for SCSI command timeout
value and fix setting of resetwaittime beyond a value.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make instance->adprecovery variable atomic and removes hba_lock spinlock
while accessing instance->adprecovery.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will add capability in driver to tell firmware that it can
throttle IOs in case controller's queue depth is downgraded post OFU
(online firmware upgrade). This feature will ensure firmware can be
downgraded from higher queue depth to lower queue depth without needing
system reboot. Added throttling code in IO path of driver, in case OS
tries to send more IOs than post OFU firmware's queue depth.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. For iMR controllers, firmware will report two queue depths:
- Controller-wide queue depth
- LDIO queue depth (240)
Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).
2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".
3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.
4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
build_and_issue_cmd should return SCSI_MLQUEUE_HOST_BUSY for a few error
cases instead of returning 1.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.
If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.
When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware will fill out per-LD data to tell driver whether a particular
LD supports region lock bypass. If yes, then driver will send non-FP
LDIO to region lock bypass FIFO. With this change in driver, firmware
will optimize certain code to improve performance.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will update device Queue depth based on interface type(SAS,
SATA..) for sysPDs. For Virtual disks(VDs), there will be no change in
queue depth (will remain 256). To fetch interface type (SAS or SATA or
FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds task management for SCSI commands. Added functions are
task abort and target reset.
1. Currently, megaraid_sas driver performs controller reset when any IO
times out. With task management support added, task abort and target
reset will be tried to recover timed out IO. If task management fails,
then controller reset will be performaned. If the task management
request times out, fail the request and escalate to the next
level (controller reset).
2. mr_device_priv_data will be allocated for all generations of
controller, but is_tm_capable flag will never be set for
controllers (prior to Invader series) as firmware support is not
available for task management.
3. Task management capable firmware will set is_tm_capable flag in
firmware API.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do proper error handling for DCMD timeout failure cases
for Fusion adapters:
1. For MFI adapters, in case of DCMD timeout (DCMD which must return
SUCCESS) driver will call kill adapter.
2. What action needs to be taken in case of DCMD timeout is decided by
function dcmd_timeout_ocr_possible(). DCMD timeout causing OCR is
applicable to the following commands:
MR_DCMD_PD_LIST_QUERY
MR_DCMD_LD_GET_LIST
MR_DCMD_LD_LIST_QUERY
MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS
MR_DCMD_SYSTEM_PD_MAP_GET_INFO
MR_DCMD_LD_MAP_GET_INFO
3. If DCMD fails from driver init path there are certain DCMDs which
must return SUCCESS. If those DCMDs fail, driver bails out. For optional
DCMDs like pd_info etc., driver continues without executing certain
functionality.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will do synhronization between OCR function and AEN function
using "reset_mutex" lock. reset_mutex will be acquired only in the
first half of the AEN function which issues a DCMD. Second half of the
function which calls SCSI API (scsi_add_device/scsi_remove_device)
should be out of reset_mutex to avoid deadlock between scsi_eh thread
and driver.
During chip reset (inside OCR function), there should not be any PCI
access and AEN function (which is called in delayed context) may be
firing DCMDs (doing PCI writes) when chip reset is happening in parallel
which will cause FW fault. This patch will solve the problem by making
AEN thread and OCR thread mutually exclusive.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds the needed check after the call to the function
mraid_mm_alloc_kioc in order to make sure that this function has not
returned NULL and therefore makes sure we do not deference a NULL
pointer if one is returned by mraid_mm_alloc_kioc. Further more add
needed comments explaining that this function call can return NULL if
the list head is empty for the pointer passed in order to allow furture
users to understand this required pointer check.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.
This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It may happen (kdump), that an interrupt is invoked just after the
setup_irqs function was called but before the tasklet was initialised.
At this phase the hw ints should have been disabled, but for unknown
reason this mechanism seems to not work properly.
From: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove PCI id based checks and use instance->ctrl_context to decide
whether controller is MFI-based or a Fusion adapter. Additionally,
Fusion adapters are divided into two categories: Thunderbolt and
Invader.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of these code changes were proposed by David Binderman.
Removed redudant check of requestorId. Redundant condition:
instance.requestorId. Check for plasma firmware 1.11 are now
restructured to support only specific device id.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Syncro firmware supports round robin I/O switching on dual path. Driver
uses validHandles to check for dual path. However, it is supposed to
check for values > 1 (not > 2).
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print firmware events in human-readable form. This will help users track
any critical firmware events without special application support.
Sample syslogd output:
megaraid_sas 0000:02:00.0: 8619 (491648347s/0x0020/WARN) - Controller temperature threshold exceeded. This may indicate inadequate system cooling. Switching to low performance mode.
The format of logged events is:
"<pci_dev_id>: <sequence_number> (<timestamp>/<locale>/<class>) - <description>"
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the issue reported at:
http://marc.info/?l=linux-scsi&m=143694494104544&w=2
Try to do chip reset at driver load time. If firmware fails to reach
ready state, try chip reset using adp_reset() callback. For Fusion
adapters the call back was previously void. Provide a suitable reset
function.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will expose max sge = 256 (earlier it was 64) if firmware
supports extended IO size (1M).
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implemented JBOD map which will provide quick access for JBOD path and
also provide sequence number. This will help hardware to fail command
to the FW in case of any sequence mismatch.
Fast Path I/O for JBOD will refer JBOD map (which has sequence number
per JBOD device) instead of RAID map. Previously, the driver used RAID
map to get device handle for fast path I/O and this not have sequence
number information. Now, driver will use JBOD map instead. As part of
error handling, if JBOD map is failed/not supported by firmware, driver
will continue using legacy behavior.
Now there will be three IO paths for JBOD (syspd):
- JBOD map with sequence number (Fast Path)
- RAID map without sequence number (Fast Path)
- FW path via h/w exception queue deliberately setup devhandle
0xFFFF (FW path).
Relevant data structures:
- Driver send new DCMD MR_DCMD_SYSTEM_PD_MAP_GET_INFO for this purpose.
- struct MR_PD_CFG_SEQ- This structure represent map of single physical
device.
- struct MR_PD_CFG_SEQ_NUM_SYNC- This structure represent whole JBOD
map in general(size, count of sysPDs configured, struct MR_PD_CFG_SEQ
of syspD with 0 index).
- JBOD sequence map size is: sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC)
+ (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1)) which
is allocated while setting up JBOD map at driver load time.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
This fixes a regression caused by commit
d3557fc8be megaraid_sas : Add separate function
for setting up IRQs This makes boot end with 'root does not exist' message on
certain adapters.
The bug is that the driver does not setup ints for cards without msi-x
support. This patch fixes it, in addition to that it moves tasklet
initialisation before enable_intr, otherwise a kernel panic may occur, when an
interrupt arrives before the tasklet is ready.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch is rebased on top of recently sent 18 patches(submitted by me) for
megaraid_sas driver.
Change the return value of wait_and_poll() and megsas_issue_blocked_cmd()
based on MFI_STAT returned by firmware for that command. Earlier driver always
send return type based on command completion (but never check MFI_STAT_OK for
that command), so even if command is failed by firmware still driver will
return SUCCESS status from these functions wait_and_poll() and
megsas_issue_blocked_cmd() and if caller of these functions does not check
command status (MFI_STAT), then it may endup using invalid data returned in
DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to
avoid this type of issue is do error handling and set proper return type from
caller function wait_and_poll() and megsas_issue_blocked_cmd().
The change proposed in this patch will fix the regression introduced in patch-
"90dc9d9 megaraid_sas : MFI MPT linked list corruption fix" inside function
megasas_ld_list_query(). Prior to this MFI MPT linked list corruption fix
patch, megasas_ld_list_query() function used to check DCMD status(returned by
firmware) but with this linked list corruption fix patch, DCMD status will not
be checked inside function megasas_ld_list_query() and introduced this issue
of wrong data being used by function megasas_ld_list_query().
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Swap the whole 32 bits we read from the hardware instead of swapping
just the 16bits we care about in place later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The fusion HBAs don't really use the instance template like the other
variants, as it branches off at a much higher level. So instead of
trying to squeeze megasas_fire_cmd_fusion into the wrong calling
convention call it locally with argument data types that match what
is passed.
[jejb: fix up 32 bit compile failure]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Converting structure fields in place is always a bad idea, and in this case
by moving it into the only caller we also only have to do a single byte
swap as most fields of this structure are never used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add noop conversions for all ones to make sparse happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>