Commit Graph

169 Commits

Author SHA1 Message Date
Greg Kroah-Hartman dd36a2d9ad Second set of IIO new device support, features and cleanups for the 4.13 cycle.
A few reverts here. One was a general failure to notice a device was already
 supported by another driver.  The second is due to a review comment pointing
 out that the original patch was a bad idea and would break existing systems.
 
 Reverts
 * bma180
   - Revert addition of support for the BMA250E it is already supported by
     the bmc150-accel and better supported at that. Oops.
 * hi8435
   - The fix for cleanup of the reset gpio stuff isn't a good way to go.  It
     breaks systems where an inverting level convertor is used.  The right fix
     is to make the original devicetree correct - even if it involves patching
     the devicetree in kernel.
 
 New Device Support
 * stm32-adc
   - STM32H7 support and bindings.
 
 Features
 * core
   - add a hardware triggered operating mode for systems in which the actual
     trigger is never seen by the kernel.  This is typically only used when
     a device 'can' use other triggers, but if a particular magic one is
     enabled the interrupt is effectively handled in hardware and we never see
     it.
 * st-lsm6dsx
   - support active low interrupts.
 * stm32-adc
   - Make the core adc clock optional as not all hardware supported requires it.
   - Make the bus clock optional in the per instance driver as it may be shared
     by all instances of the ADC and is handled by the core.
   - Rework to have a data structure representing the device type specific
     elements.
 * stm32-trigger (and counter)
   - Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
   - Add an attribute to configure device modes for quadrature counting etc.
 
 Clean ups and minor fixes
 * IIO core.
   - use __sysfs_match_string() helper rather than open coding the same.
 * ad7791
   - use sysfs_match_string() helper rather than open coding the same.
 * aspeed-adc
   - handle return value of clk_prepare_enable
 * cpcap
   - Fix default register values and ensure the battery thermistor is enabled
     correctly.
   - Fix the reported die temperature where we can - docs are lacking.
   - Remove the hung interrupt quirk as no longer happens due to fix in the
     mfd driver.
 * hi8435
   - Remove &s from hi8435_info definition as unneeded and inconsistent.
 * hid-sensor-trgger
   - Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
 * ina2xx
   - Make the use of iio_info_mask* elements consistent for all channels.
     This doesn't have any visible effect, but acts as clear documentation of
     which channels various resulting attributes apply to.
 * lpc32xx
   - handle the return value of clk_prepare_enable.
 * meson-saradc
   - NULL instead of 0 for pointer.
 * mma9551
   - use NULL for GPIO connection ID to aid implementation fo ACPI support.
     Here the connection ID doesn't actually tell us anything and it is much
     easier to deal with the driver if it's not there.
 * mpu6050
   - Fix lock issues through use of a local mux.
   - Replace sprintf with scnprintf as appropriate.
   - Check whoami against all known values.  This allows for a small number of
     boards where we are really fishing for the part not being present at all.
     It is unfortunately common to have undescribed changes to use newer chips.
     We paper over this but just emitting a warning for those cases as long as
     we know about.
 * mxs-lradc
   - Fix some non static warnings.
 * rcar-adc
   - Part of making the naming for this part consistent across the kernel.
 * st_accel
   - drop some spi_device_id entries for variants with no SPI support
 * st_magn
   - drop some spi_device_id entries for variants with no SPI support.
 * sx9500
   - Use devm_gpiod_get instead of indexed value with an index of 0 on all
     occasions.
 * twl4030
   - Drop unused twl4030_get_madc_conversion as callers removed now throughout
     kernel.
   - Unexport twl4030_madc_conversion() as no used only within this driver.
   - Drop twl4030_madc_user_params as not used now.
   - Drop twl4030_madc_request.func_cb as not used now.
   - Fold the twl4030-madc.h header into the driver as no longer used anywhere
     else in the kernel.
 * xilinx
   - Handle the return value of clk_prepare_enable
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAllJSCURHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FogTTQ//bbAzHKB0qTwusFN5jrz1JqjGj3+bMXH/
 KumP4nj7NzwKBe4tDe40FsdkZ4c+Um8pK2Aj7iJZojwTcCi02VVjbM++Gj0akMTZ
 MIlrEkTvqVsmVFG085hloSiFU2xXfTnfQmp19M9QtyDnHkgBMo9sOFnBK3EG+Se4
 NIliUvq8PJzCjTRVafSeSFNoDMwXXQTIKhfq8TDSeOG9o5mCTgAdy8yGiZ2ag/Ok
 peFfwauGs9Gg6tRour7UxccawuLnuzPNzwzUUSG3gkdIUTQVD6YHAzXzwblnB5P6
 0ZcErJpGSLAYcHQH310ZRTizhhW+vi+ftWUkps81xqpmFp3+EydVnJS0MZXYgM2o
 Cv6wbohp9w22I5/B9TMEfL7vnj1i4iZoJfi00Su1HBDHBiNpXISRc/fnkRMWavhr
 gvypyxngQmXm1JN/R8UMbJQsSpH3TN07AYF1qx0Tktfyx4S18rdW4hwt+kBNe9ni
 5G9xQU8IhmN8yvHMsTvZHbAmbuOR6iaghx3arf65qdHPvKSQ/nTSlran9U1JPvyJ
 tWVKtPaY5zEGgkQBmWee+qWkWOBGYDC4nmTwijB0u61Deq+5hGg55cZPd0fSXLMg
 6ecNg2v7zrdYldulOpfdNUEOrXa/NYBEAuYUNvccp8DArOqdazkCyO3DlDFDUXRw
 RKNE7Btx/rU=
 =2fJI
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of IIO new device support, features and cleanups for the 4.13 cycle.

A few reverts here. One was a general failure to notice a device was already
supported by another driver.  The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.

Reverts
* bma180
  - Revert addition of support for the BMA250E it is already supported by
    the bmc150-accel and better supported at that. Oops.
* hi8435
  - The fix for cleanup of the reset gpio stuff isn't a good way to go.  It
    breaks systems where an inverting level convertor is used.  The right fix
    is to make the original devicetree correct - even if it involves patching
    the devicetree in kernel.

New Device Support
* stm32-adc
  - STM32H7 support and bindings.

Features
* core
  - add a hardware triggered operating mode for systems in which the actual
    trigger is never seen by the kernel.  This is typically only used when
    a device 'can' use other triggers, but if a particular magic one is
    enabled the interrupt is effectively handled in hardware and we never see
    it.
* st-lsm6dsx
  - support active low interrupts.
* stm32-adc
  - Make the core adc clock optional as not all hardware supported requires it.
  - Make the bus clock optional in the per instance driver as it may be shared
    by all instances of the ADC and is handled by the core.
  - Rework to have a data structure representing the device type specific
    elements.
* stm32-trigger (and counter)
  - Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
  - Add an attribute to configure device modes for quadrature counting etc.

Clean ups and minor fixes
* IIO core.
  - use __sysfs_match_string() helper rather than open coding the same.
* ad7791
  - use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
  - handle return value of clk_prepare_enable
* cpcap
  - Fix default register values and ensure the battery thermistor is enabled
    correctly.
  - Fix the reported die temperature where we can - docs are lacking.
  - Remove the hung interrupt quirk as no longer happens due to fix in the
    mfd driver.
* hi8435
  - Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
  - Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
  - Make the use of iio_info_mask* elements consistent for all channels.
    This doesn't have any visible effect, but acts as clear documentation of
    which channels various resulting attributes apply to.
* lpc32xx
  - handle the return value of clk_prepare_enable.
* meson-saradc
  - NULL instead of 0 for pointer.
* mma9551
  - use NULL for GPIO connection ID to aid implementation fo ACPI support.
    Here the connection ID doesn't actually tell us anything and it is much
    easier to deal with the driver if it's not there.
* mpu6050
  - Fix lock issues through use of a local mux.
  - Replace sprintf with scnprintf as appropriate.
  - Check whoami against all known values.  This allows for a small number of
    boards where we are really fishing for the part not being present at all.
    It is unfortunately common to have undescribed changes to use newer chips.
    We paper over this but just emitting a warning for those cases as long as
    we know about.
* mxs-lradc
  - Fix some non static warnings.
* rcar-adc
  - Part of making the naming for this part consistent across the kernel.
* st_accel
  - drop some spi_device_id entries for variants with no SPI support
* st_magn
  - drop some spi_device_id entries for variants with no SPI support.
* sx9500
  - Use devm_gpiod_get instead of indexed value with an index of 0 on all
    occasions.
* twl4030
  - Drop unused twl4030_get_madc_conversion as callers removed now throughout
    kernel.
  - Unexport twl4030_madc_conversion() as no used only within this driver.
  - Drop twl4030_madc_user_params as not used now.
  - Drop twl4030_madc_request.func_cb as not used now.
  - Fold the twl4030-madc.h header into the driver as no longer used anywhere
    else in the kernel.
* xilinx
  - Handle the return value of clk_prepare_enable
2017-06-26 07:09:23 +02:00
Greg Kroah-Hartman 7bf1e44f86 Merge 4.12-rc5 into staging-next
We want the IIO fixes and other staging driver fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-12 08:20:47 +02:00
Andy Shevchenko c306dbd88c iio: proximity: sx9500: Use devm_gpiod_get()
Since index is always 0 replace devm_gpiod_get_index() by devm_gpiod_get().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-06-11 15:07:34 +01:00
Matt Ranostay 9122b54f26 iio: proximity: as3935: fix iio_trigger_poll issue
Using iio_trigger_poll() can oops when multiple interrupts
happen before the first is handled.

Use iio_trigger_poll_chained() instead and use the timestamp
when processed, since it will be in theory be 2 ms max latency.

Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-05-07 13:21:55 +01:00
Matt Ranostay 275292d3a3 iio: proximity: as3935: fix AS3935_INT mask
AS3935 interrupt mask has been incorrect so valid lightning events
would never trigger an buffer event. Also noise interrupt should be
BIT(0).

Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
CC: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-27 16:28:57 +01:00
Matt Ranostay d532e5b2bc iio: proximity: as3935: move storm out of range check
Move out of storm check to apply to IIO_CHAN_INFO_RAW so the reported
results are constant between the former and the IIO_CHAN_INFO_PROCESSED

Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-27 07:22:46 +01:00
Matt Ranostay 6272c0de13 iio: proximity: as3935: recalibrate RCO after resume
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.

Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-26 07:06:31 +01:00
Greg Kroah-Hartman df47c0a638 Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12.
 There is a fix for a regression caused by another fix (hid sensors
 hardware seems to vary a lot in how various corner cases are handled).
 
 * ad7303
   - fix channel description. Numeric values were being passed as characters
   presumably leading to garbage from the userspace interface.
 * as3935
   - the write data macro was wrong so fix it.
 * bmp280
   - incorrect handling of negative values as being unsigned broke humidity
   calculation.
 * hid-sensor
   - Restore the poll and hysteresis values after resume as some hardware
   doesn't do it.
 * stm32-trigger
   - buglet in reading the sampling frequency
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAljw8ScRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FojZvBAAh8K9e+3ObpS6/0wj26/XsakiFn4v2ah0
 xKUnafxAVVxU3AU01IJ3CtNdIMyqMwpnB+PvnpgDzZw749QrYKPsBIzheK64eabe
 fzA34X5MWGLwUdOXpfEB0xvsylWjJrqsf1rahgZjiUKkPeZe9EwzPM/fP1sEl5gu
 p+vfSMckboFaKheoQwnWMUTBp0HK+nbFpcSBzljX68u+epiXpDGrjuZC8NJ3JuBn
 Bloz9AhDliIn477H7mIUTXBbt3ixLIDiJ7haQuTNlagosPoUtCBpwY2O9mZ7VRVs
 wM62h7/F170077ReQJRjlfck+7uHoIgDeS46w5UYTzA1HJLxs+veO5xv3VOtHIUg
 BZ+mibQyIUBrFeyYDVbeUpBTffiU6rA+yiM4WFwUFabl7t7rlG0NhLEx7OIQcFMm
 l8u/5JUoJcoykaO8c9Jx5XtrgkXq+rCWVAmhjHqUDAlvsMa6pJWEyqgaVcQeIbdw
 ns9ppJRlOmEst7lMab9TI7BJp3oCIH6uRmctbme42Rw8XgDFdltxqkxmjB8d+cDC
 Q0INhNJN1jRgz6rT6lkxVhAYKtaP5T8qZeliT4MO1E59ggOVSSf8zuhjrEMUK397
 Tu/k7fmATtiKSG+blwYZVRC3+ixh/oKZsvfwZ4O+mFJyhQ616nKMYAywoaZcM8WT
 Z1ABipUDwsE=
 =H5KS
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Fifth set of IIO fixes for the 4.11 cycle.

As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).

* ad7303
  - fix channel description. Numeric values were being passed as characters
  presumably leading to garbage from the userspace interface.
* as3935
  - the write data macro was wrong so fix it.
* bmp280
  - incorrect handling of negative values as being unsigned broke humidity
  calculation.
* hid-sensor
  - Restore the poll and hysteresis values after resume as some hardware
  doesn't do it.
* stm32-trigger
  - buglet in reading the sampling frequency
2017-04-18 19:38:38 +02:00
Matt Ranostay 84ca8e364a iio: proximity: as3935: fix as3935_write
AS3935_WRITE_DATA macro bit is incorrect and the actual write
sequence is two leading zeros.

Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-14 14:48:58 +01:00
simran singhal 7ab89e1e23 iio: proximity: as3935: constify attribute_group structures
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:

@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};

@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;

@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;

File size before:
   text	   data	    bss	    dec	    hex	filename
   4037	    288	      0	   4325	   10e5	drivers/iio/proximity/as3935.o

File size after:
   text	   data	    bss	    dec	    hex	filename
   4101	    256	      0	   4357	   1105	drivers/iio/proximity/as3935.o

Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-04-01 11:26:10 +01:00
Lars-Peter Clausen b2027d16df iio: pulsedlight-lidar-lite-v2: Set parent device
Initialize the parent of the IIO device to the device that registered it.
This makes sure that the IIO device appears the right level in the device
hierarchy.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-02-19 12:02:31 +00:00
Andreas Klinger feda284004 iio: distance: add devantech us ranger srf04
This patch adds support for the ultrasonic ranger srf04 of devantech.

This device is measuring the distance of objects in a range between 1 cm
and 3 meters and a theoretical resolution of 3 mm.

There are two GPIOs used:
  - trigger: set as output to the device when the measurement should start
  - echo: set by the device when the ultrasonic wave is sent out and reset
    when the echo is recognized; this needs to be an interrupt input

The time between setting and resetting the echo pin is the time the
waveform needed for one round trip. This time is recorded in the interrupt
handler.

The distance is calculated in the read function by using the ultrasonic
speed at 20 degrees celsius which is about 343 m/s.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-02-04 12:19:20 +00:00
Andreas Klinger 78f839029e iio: distance: srf08: add IIO driver for us ranger
This is the IIO driver for devantech srf08 ultrasonic ranger which can be
used to measure the distances to an object.

The sensor supports I2C with some registers.

Supported Features include:
 - read the distance in ranging mode in centimeters
 - output of the driver is directly the read value
 - together with the scale the driver delivers the distance in meters
 - only the first echo of the nearest object is delivered
 - set sensitivity as analog value in the range of 0-31  means setting
   gain register on device
 - set range registers; userspace enters max. range in millimeters in
   43 mm steps

Features not supported by this driver:
 - ranging mode in inches or in microseconds
 - ANN mode
 - change I2C address through this driver
 - light sensor

The driver was added in the directory "proximity" of the iio subsystem and
the menu in den config is now called "Proximity and distance sensors"

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-28 16:38:24 +00:00
Alison Schofield 6b2e7589b8 iio: proximity: sx9500: claim direct mode during raw proximity reads
Driver was checking for direct mode but not locking it.  Use the
claim/release helper functions to guarantee the device stays in
direct mode during raw reads of proximity data.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-21 12:21:53 +00:00
Matt Ranostay b257c1a45e iio: pulsedlight-lidar-lite-v2: add lidar-lite-v3 property
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-12-31 15:18:31 +00:00
Matt Ranostay a84a6a8aa0 iio: proximity: pulsedlight-lidar-lite-v2: cleanup power management
Remove pm_runtime_mark_last_busy() call that wasn't need in the probe
since the device should be put to sleep.

Clarification from Matt:
Basically it going to be suspended once pm_runtime_idle() is called,
and setting the last busy is useless and not needed.
Clearly this doesn't affect the device running but just makes the code
more consistent with other uses.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-10-23 19:34:26 +01:00
Greg Kroah-Hartman 552edf8d79 Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
 * ad8801 dac
   - new driver supporting ad8801 and ad8803 DACs.
 * adc12138
   - new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
 * ltc2485 adc
   - new driver
 * mxc6255
   - add support for the mxc6225 part name and fixup the ID check so it works.
 * vz89x VOC sensor
   - add support for the vz89te part which drops the voc_short channel and adds
     CRCs compared to other supported parts.
 
 New features
 * core
   - immutable triggers.  These effectively grant exclusive control over a
     trigger. The typical usecase is a device representing an analog part
     (perhaps a MUX) that needs to control the sampling of a downstream
     ADC.
   - resource managed trigger registration and triggered_buffer_init.
   - iio_push_event now protected against case of the event interface
     registration not having yet occured.  Only matters if an interrupt
     can occur during this window - might happen on shared interrupt lines.
   - helper to let a driver query if the trigger it is using is provided by
     itself (using the convention of both device and trigger having the same
     parent).
 * tools
   - iio-utils. Used channel modifier scaling in preference to generic scaling
     when both exist.
 * at91-adc
   - Add support for touchscreen switches closure time needed by some newer
     parts.
 * stx104
   - support the ADC channels on this ADC/DAC board. As these are the primary
     feature of the board also move the driver to the iio/adc directory.
 * sx9500
   - device tree bindings.
 
 Cleanups / Fixes
 * ad5755
   - fix an off-by-one on devnr limit check (introduced earlier this cycle)
 * ad7266
   - drop NULL check on devm_regulator_get_optional as it can't return NULL.
 * ak8974
   - avoid an unused functional warning due to rework in PM core code.
   - remove .owner field setting as done by i2c_core.
 * ina2xx
   - clear out a left over debug field from chip global data.
 * hid-sensors
   - avoid an unused functional warning due to rework in PM core code.
 * maxim-thermocouple
   - fix non static symbol warnings.
 * ms5611
   - fetch and enable regulators unconditionally when they aren't optional.
 * sca3000
   - whitespace cleanup.
 * st_sensors
   - fetch and enable regulators unconditionally rather than having them
     supported as optional regulators (missunderstanding on my part amongst
     others a while back)
   - followup to previous patch fixes error checking on the regulators.
   - mark symbols static where possible.
   - use the 'is it my trigger' help function.  This prevents the odd case
     of another device triggering from the st-sensors trigger whilst the
     st-sensors trigger is itself not using it but rather using say an hrtimer.
 * ti-ads1015
   - add missing of_node_put.
 * vz89x
   - rework to all support of new devices.
   - prevent reading of a corrupted buffer.
   - fixup a return value of 0/1 in a bool returning function.
 
 Address updates
 - Vlad Dogaru email address change.
 -----BEGIN PGP SIGNATURE-----
 
 iQIuBAABCAAYBQJX1wW9ERxqaWMyM0BrZXJuZWwub3JnAAoJEFSFNJnE9BaII9UP
 /jXkXtaL62pvipMuEujmpR7j/A+GhmSWHhnbJ9XXeGZStGMUummTyaM+6WZoCKUH
 bMtZh/ETsn+FI7mD7P/FtwHauoxSmndcaAfB6cDKQMVakbXbz4VHrim256cY3gvq
 dzF5nYX+wDue6D7k55VPrtV1isBfipeCXKBtzBlAXaVE2FK2qKP+PIlAln8Ql5/l
 b5B3pvqu0YVED4t2MzyVWcVidPOEh9GgwHu7Ba+kjVi6zuB4w+r5ZreIObb5IR54
 FDcEwL6vV9AlmX15Pc18NO+50bZ8TvgT4y7ISqaOwszaIEoDAc0hXT7TdUOscmtt
 LIbhzHVMVkPSjxvtpz2ui8GfqzhxLi3ZzfNHRegOqH4b2Cpoh4zdwn7nCyJEHZV5
 simAL00FGjzp6B4Zp+Ly6ygKzpF3iXZce0Qjlr/ge+ioNIrfuK10sdLw8NZA5GUB
 JcFYijcFLUb0Cu/KjZ7njlfdAN9Tt94xzpnllM8+j4M50Nhbw05YNhIxB7RxmeSH
 Y44/oBLG51SgtlIg5Z4rULRAcOC5dty73Inb0n4lbN/pjgIcnh+EYtPeI2fA8vyB
 XYqr4xx+A3ZX1yKpYLYO+JYtVsVq9RGYdb501uBhEE3/GWEpxZvbyqHnPwwfM+Pf
 ZNuBceBxM3yyi4Z/lKkZnQbaF/1fFoG7FO1n6iRpb8Ci
 =V1xL
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of iio new device support, features and cleanups for the 4.9 cycle.

New device support
* ad8801 dac
  - new driver supporting ad8801 and ad8803 DACs.
* adc12138
  - new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
  - new driver
* mxc6255
  - add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
  - add support for the vz89te part which drops the voc_short channel and adds
    CRCs compared to other supported parts.

New features
* core
  - immutable triggers.  These effectively grant exclusive control over a
    trigger. The typical usecase is a device representing an analog part
    (perhaps a MUX) that needs to control the sampling of a downstream
    ADC.
  - resource managed trigger registration and triggered_buffer_init.
  - iio_push_event now protected against case of the event interface
    registration not having yet occured.  Only matters if an interrupt
    can occur during this window - might happen on shared interrupt lines.
  - helper to let a driver query if the trigger it is using is provided by
    itself (using the convention of both device and trigger having the same
    parent).
* tools
  - iio-utils. Used channel modifier scaling in preference to generic scaling
    when both exist.
* at91-adc
  - Add support for touchscreen switches closure time needed by some newer
    parts.
* stx104
  - support the ADC channels on this ADC/DAC board. As these are the primary
    feature of the board also move the driver to the iio/adc directory.
* sx9500
  - device tree bindings.

Cleanups / Fixes
* ad5755
  - fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
  - drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
  - avoid an unused functional warning due to rework in PM core code.
  - remove .owner field setting as done by i2c_core.
* ina2xx
  - clear out a left over debug field from chip global data.
* hid-sensors
  - avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
  - fix non static symbol warnings.
* ms5611
  - fetch and enable regulators unconditionally when they aren't optional.
* sca3000
  - whitespace cleanup.
* st_sensors
  - fetch and enable regulators unconditionally rather than having them
    supported as optional regulators (missunderstanding on my part amongst
    others a while back)
  - followup to previous patch fixes error checking on the regulators.
  - mark symbols static where possible.
  - use the 'is it my trigger' help function.  This prevents the odd case
    of another device triggering from the st-sensors trigger whilst the
    st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
  - add missing of_node_put.
* vz89x
  - rework to all support of new devices.
  - prevent reading of a corrupted buffer.
  - fixup a return value of 0/1 in a bool returning function.

Address updates
- Vlad Dogaru email address change.
2016-09-14 20:42:03 +02:00
Greg Kroah-Hartman 9c2edd8b5b Merge 4.8-rc5 into staging-next
We want the staging fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-05 08:13:24 +02:00
Christoph Fritz a5c8b11a36 iio: sx9500: add final devicetree support
This makes sx9500 driver usable on devicetree based platforms too.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-09-03 15:26:28 +01:00
Daniel Wagner 8c11e16177 iio: sx9500: Use complete() instead of complete_all()
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().

The usage pattern of the completion is:

waiter context                          waker context

sx9500_read_proximity()
  sx9500_inc_chan_users()
  sx9500_inc_data_rdy_users()
  wait_for_completion_interruptible()

                                        s9500_irq_thread_handler()
                                          complete()

  reinit_completion()

Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-15 18:01:27 +01:00
Alison Schofield f8adf645db iio: proximity: as3935: set up buffer timestamps for non-zero values
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-15 15:39:27 +01:00
Gregor Boirie bc2b7dab62 iio:core: timestamping clock selection support
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.

Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 19:41:38 +01:00
Greg Kroah-Hartman 3c9a6793bd Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
 * NXP took over freescale. Update the mma8452 header to reflect this.
 * Martin Kepplinger email address change in mma8452 header.
 * Adriana Reus has changed email address. Update .mailmap.
 * Matt Ranostay has changed email address. Update .mailmap.
 
 New Device Support
 * max1363
   - add the missing i2c_device_ids for a couple of parts so they can actually
     be used.
 * ms5867
   - add device ids for ms5805 and ms5837 parts.
 
 New Features
 * ad5755
   - DT support.  This one was a bit controversial and under review for a long
     time.  Still no one could come up with a better solution.
 * stx104
   - add gpio support
 * ti-adc081c
   - Add ACPI device ID matching.
 
 Core changes
 * Refuse to register triggers with duplicate names.  There is no way to
   distinguish between them so this makes no sense.  A few drivers do not
   generate unique names for each instance of the device present.  We can't
   fix this without changing ABI so leave them and wait for someone to
   actually take the rare step of two identical accelerometers on the same
   board.
 * buffer-dma
   - use ARRAY_SIZE in a few appropriate locations.
 
 Tools
 * Fix the fact that the --trigger-num option in generic_buffer didn't allow
   0 which is perfectly valid in the ABI.
 
 Cleanups
 * as3935
   - improve error reporting.
   - remove redundant zeroing of a field in iio_priv.
 * gp2ap020a00f
   - use the iio_device_claim_*_mode helpers rather than open coding locking
   around mode changes.
 * isl29125
   - use the iio_device_claim_*_mode helpers rather than open coding locking.
 * lidar
   - use the iio_device_claim_*_mode helpers rather than open coding locking.
 * mma8452
   - more detail in devices supported description in comments (addresses and
   similar)
 * sca3000
   - add a missing error check.
 * tcs3414
   - use the iio_device_claim_*_mode helpers rather than open coding locking.
 * tcs3472
   - use the iio_device_claim_*_mode helpers rather than open coding locking.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXdAT2AAoJEFSFNJnE9BaIq68P/3Z0q1lc1cb+K8HV5jgukEKw
 eoxZa5lFIOuHAGeXo9GAdJiH5oT/yAIhadf3gzuuQLaTJwWYKD51aPVwgpT5M2+x
 Bnu2XiYcaoIm/Foat70ycjeYaGxO/xO2vbLp5v0BJV2ujvjm/oCKw5pxYeU4Jm63
 iKaZo9jn/HoshOMpZBrcPZ7Q1TogRdopBNe2fsc8nXFFsv8ODjOZ9Nebs2lk36e+
 PWLUWfSkv2LMBSE2LOFyjSW8E4ItBBngBcyqBTFiiln7mpXU5Vv2QSvUhpP2YjUZ
 rxKvDiG7ADuxMr901whASxyCO180yCxTRIcBsN8oP73gTGHrJnMT0Sptfz7AUUVN
 gJneiy+iy3TecJ/R6w/DnNzqmZMiEVqlYGkdXVGu8SXrKWilvzcTp5iTmDVM5zLb
 1fDZxjbLdNJuHzoSYNiCBcnfzIixOAyKTGFi3jUaPPQ/Lc1qfmgerWWlOzKeUgCZ
 5Bzak8MvWuxcO7jkMG8mbARufy3Nu6eh8a39JXFhViGtTtySydMa8eXdYPjqoAtv
 vgwJNh9U53yYui8i7vU90dM3gJaGg5a4R6EjEKCYcEJf6kM9Go8xCvjU8YWPtIKk
 rfykpPkKcQzbax07YKvb4f015x7r0V6WCGJjPn0Fi14ugNGJJ6M88l+2UcXcx1zS
 RRtVRD49Le7pIDCs1Rqn
 =6Lja
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second round of new iio device support, features and cleanups in the 4.8 cycle

Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.

New Device Support
* max1363
  - add the missing i2c_device_ids for a couple of parts so they can actually
    be used.
* ms5867
  - add device ids for ms5805 and ms5837 parts.

New Features
* ad5755
  - DT support.  This one was a bit controversial and under review for a long
    time.  Still no one could come up with a better solution.
* stx104
  - add gpio support
* ti-adc081c
  - Add ACPI device ID matching.

Core changes
* Refuse to register triggers with duplicate names.  There is no way to
  distinguish between them so this makes no sense.  A few drivers do not
  generate unique names for each instance of the device present.  We can't
  fix this without changing ABI so leave them and wait for someone to
  actually take the rare step of two identical accelerometers on the same
  board.
* buffer-dma
  - use ARRAY_SIZE in a few appropriate locations.

Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
  0 which is perfectly valid in the ABI.

Cleanups
* as3935
  - improve error reporting.
  - remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
  - use the iio_device_claim_*_mode helpers rather than open coding locking
  around mode changes.
* isl29125
  - use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
  - use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
  - more detail in devices supported description in comments (addresses and
  similar)
* sca3000
  - add a missing error check.
* tcs3414
  - use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
  - use the iio_device_claim_*_mode helpers rather than open coding locking.
2016-06-29 15:35:01 -07:00
Matt Ranostay 4d462b85e7 iio: proximity: as3935: remove redundant zeroing of tune_cap
This is redundant as the containing stucture is allocated as part of
iio_device_alloc using kzalloc and hence is already 0.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-27 20:59:12 +01:00
Arnd Bergmann 22ed1a1c1c iio: as3935: improve error reporting in as3935_event_work
gcc warns about a potentially uninitialized variable use
in as3935_event_work:

drivers/iio/proximity/as3935.c: In function ‘as3935_event_work’:
drivers/iio/proximity/as3935.c:231:6: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

This case specifically happens when spi_w8r8() fails with a
negative return code. We check all other users of this function
except this one.

As the error is rather unlikely to happen after the device
has already been initialized, this just adds a dev_warn().
Another warning already exists in the same function, but is
missing a trailing '\n' character, so I'm fixing that too.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-27 20:59:10 +01:00
Greg Kroah-Hartman af52739b92 Merge 4.7-rc4 into staging-next
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-20 08:25:44 -07:00
Matt Ranostay 9e18265443 iio: proximity: lidar: switch to iio_device_claim_*_mode helpers
Switch from using indio_dev->mlock to the iio_device_claim_*_mode
helper functions.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-11 17:08:20 +01:00
Matt Ranostay 90e9a9500f iio: proximity: as3935: remove redundant MODULE_ALIAS
MODULE_ALIAS isn't needed since the module name is the same as the alias
defined.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-05-29 20:09:43 +01:00
Matt Ranostay 37b1ba2c68 iio: proximity: as3935: fix buffer stack trashing
Buffer wasn't of a valid size to allow the timestamp, and correct padding.
This patchset also moves the buffer off the stack, and onto the heap.

Cc: george.mccollister@gmail.com
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-05-22 20:54:15 +01:00
Matt Ranostay 7d0643634e iio: proximity: as3935: remove triggered buffer processing
Triggered buffers shouldn't return processed data, and the respective
conversion was overflowing the defined .realbits for the channel.

Cc: george.mccollister@gmail.com
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-05-22 20:53:53 +01:00
Matt Ranostay 5138806f16 iio: proximity: as3935: correct IIO_CHAN_INFO_RAW output
IIO_CHAN_INFO_RAW was returning processed data which was incorrect.
This also adds the IIO_CHAN_INFO_SCALE value to convert to a processed value.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-05-22 20:53:36 +01:00
Matt Ranostay f8d9d3b434 iio: convert to common i2c_check_functionality() return value
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-02-27 17:17:43 +00:00
Matt Ranostay 9979e320b5 iio: proximity: lidar: correct return value
lidar_i2c_xfer() function was never a non-positive value on error,
and this correct that with a -EIO return code.

Fixes: 366e65633c ("iio: proximity: lidar: optimize i2c transactions")
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-01-03 17:54:08 +00:00
Greg Kroah-Hartman 35ea984dac Second set of IIO new drivers, functionality and cleanups for the 4.5 cycle.
The big one here is the configfs support which has been a long time in the
 works but should allow for cleaner ways to do instantiation of those elements
 of IIO that aren't directly connected to specific hardware. Lots of cool new
 stuff we can use this for in the works!
 
 New core stuff (basically all configfs support related)
 * Configfs support
   - Core support (was waiting for a configfs patch that went in around 4.4rc2)
   - A little fixlet to add a configfs.h to contain a reference to the
     configfs_subsystem structure.
 * Some infrastructure to simplify handling of software based triggers
   (i.e. ones with no actual hardware associated with them)
 * A high resolution timer based trigger.  This has been around for years
     but until the configfs support was ready we didn't have a sensible way
     of instantiating instances of it (the method used for the sysfs_trigger
     has never been really satisfactory)
 
 New Device Support
 * AMS iAQ Volatile Organic Compounds sensor support.
 * Freescale imx7d ADC driver
 * Maxim MAX30100 oximeter driver (note that for these devices most of the
   smart stuff will be in userspace - effectively they are just light sensors
   with some interesting led synchronization as far as the kernel is concerned).
 * Microchip mcp3421 support added to the mcp3422 driver.
 * TI adc124s021 support added to the adc128s052 driver.
 * TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
   for these parts, the usecase is somewhat different so it is unclear at this
   point if the hwmon driver will eventually be replaced by a bridge from
   this driver.  In the meantime the Kconfig dependencies should prevent both
   from being built.
 
 New driver functionality
 * us8152d power management support.
 
 Cleanups, fixups
 * Use list_for_each_entry_safe instead of list_for_each_safe with the entry
   bit coded longhand.
 * Select IRQ_WORK for IIO_DUMMY_EVGEN.  This is a fix that somehow got lost
   when the driver was moved so lets do it again.
 * st-accel - drop an unused define.
 * vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
   instead of multiple calls where supported (fall back to smbus calls as
   before if not).
 * Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
   drivers instead of direct access to the structure element.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJWbX6IAAoJEFSFNJnE9BaI6E4QAIvGXHn4ew8ZH+IF3UP+n47C
 WWtgeh7dEvhqpmXN3eWVo9bxA1JdwbE4/purWttszoJjzqowT0qAt6PuIUME+Md4
 3jOQ41Sc99YjttIwkLpWTqq3H5c3Tn3q9guZ3Imiz9rmpgHRePQ8aatMGUpOp53m
 AEY5JQHqCoWHLMEbEy/5w8RJdNf3cy3Re4kjtwrtp7CMynC4ob7dKE7kcZRvywEw
 6m4hVOQusLvygg1j235czwBDnf79qYOo96z93Pk/auQlqKX3ce/7yQW3GXvWl97a
 8FOmse3FNzX3jwWHELOdAZWIQSLBSqP9N4716qa4orVSihzqAZQ5CSEBPB0r2LS2
 cgK4BL6+xjDkwXn9ui4FiyLdUeUjz/zRhvwFZdjwP63hGf5n9ggZO3RuVslc6/8z
 DOHY5mLdg8CFlMlZUCnCc+1BjU8lgf90+a46Vx4ACJJiqIJrvNRxRKGQZyY/C9sO
 O8h0Ep5mWovcK1+SWdQSsfxdcWcdb0nJFG/VQeJVxMeJR+5mD5lCYmIj5xFkOxJU
 WP9xm+7rsCqSPW+vp8hlY3EWunIQB4gWROvLzWCTS2bKW7B12t1UapLZBrI1f6vK
 JuqHrjKkK7RBRAEldKz6cWCToEaHE+I/k+uIRhlp0of2IPEvGpnm3NoPN1XH3RID
 9boPy/eHuShq8EVg0WUt
 =54PR
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.5b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of IIO new drivers, functionality and cleanups for the 4.5 cycle.

The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!

New core stuff (basically all configfs support related)
* Configfs support
  - Core support (was waiting for a configfs patch that went in around 4.4rc2)
  - A little fixlet to add a configfs.h to contain a reference to the
    configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
  (i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger.  This has been around for years
    but until the configfs support was ready we didn't have a sensible way
    of instantiating instances of it (the method used for the sysfs_trigger
    has never been really satisfactory)

New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
  smart stuff will be in userspace - effectively they are just light sensors
  with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
  for these parts, the usecase is somewhat different so it is unclear at this
  point if the hwmon driver will eventually be replaced by a bridge from
  this driver.  In the meantime the Kconfig dependencies should prevent both
  from being built.

New driver functionality
* us8152d power management support.

Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
  bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN.  This is a fix that somehow got lost
  when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
  instead of multiple calls where supported (fall back to smbus calls as
  before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
  drivers instead of direct access to the structure element.
2015-12-26 17:03:33 -08:00
Greg Kroah-Hartman 93c222c0e1 Merge 4.4-rc5 into staging-next
We want those fixes in here for testing.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-13 19:23:01 -08:00
Matt Ranostay 366e65633c iio: proximity: lidar: optimize i2c transactions
Optimize device tranactions using i2c transfers versus multiple
possibly racey i2c_smbus_* function calls, and only one transaction
for distance measurement. Falls back to smbus method if i2c
functionality isn't available.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-12-05 16:40:48 +00:00
Greg Kroah-Hartman f3cf3fb7ec First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
 support added by Lars-Peter Clausen. It's been in the works for a long time
 and it will be interesting to see what hardware support shows up now that
 this is available.
 
 New core features + associate cleanup.
 * Add generic DMA buffer infrastructure
 * Add a DMAengine framework based buffer
  Also associated minor changes.
    - Set the device buffer watermark based on the minimum watermark for all
      attached buffers rather than just the 'primary' one.
    - iio_buffer_init - only set the watermark default if one hasn't already
      been provided.  This allows simple support for devices with a fixed
      watermark.
    - read only attribute for watermark on fixed watermark devices.
    - add explicit buffer enable/disable callbacks to allow the buffer to
      do more than trivial actions when it is being turned on and off.
 * IIO_VAL_INT support in write_raw_get_fmt function.
 
 New device support
 * Freescale MMA7455/7456L accelerometers
 * Memsic MXC6255XC accelerometer
 * ST lis2dh12 accelerometer
 * TI ADS8688 ADC
 * TI Palamas (twl6035/7) gpadc
 
 New driver features
 * mma8452
   - support either of the available interrupt pins to cope with the case
     where board layout has lead to a particular one being connected.
 
 Staging graduation
 * Dummy driver
   - this driver acts as both an example and a test device for those with
     out hardware to develop userspace code against.
 
 Cleanups and minor bits and bobs.
 * treewide
   - Sort out the ordering of iio_device_register/unregister vs runtime
     pm function calls so that it's all nice and consistent and not race
     prone.
   - Check sscanf return values.  None of the cases will actually happen as
     the strings are supplied internally, but best to be consistent on this.
 * ad7780
   - switch over to the gpio descriptor interface and remove the now unused
     platform data which gets rid of a header entirely.
 * ad7793
   - drop a pointless else statement.
 * at91_adc
   - Swap kmalloc_array in for a kmalloc doing the same job.
 * dummy
   - get rid of some commented out lines that snuck in during the move of
     the driver.
 * lm3533-als
   - Print an error message on provision of an invalid resistance.
 * mcp320x
   - Add compatible strings with vendor prefix and deprecate those with
     no vendor prefix.
 * mxs-lradc
   - Use BIT macro in various places rather than shifted ones.
 * pa12203001
   - Power off the chip if the registration fails.
 * pulsedlight-lidar-lite
   - add runtime PM support.
 * xilinx XADC
   - constify an iio_buffer_setup_ops structure.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJWUcmhAAoJEFSFNJnE9BaIyjYP/0A+CZMUqIGbYG9qFxnq7yYZ
 977Wt/gGI8+Jq5RwNw6gTfhp2GrCN+5gzDbE2mBEn94c6SKBrj2Q9trW1FQ+Nhfx
 9bZoyq3ZPRCV+efEDGfeK/JWRwv+V6IWwAF2J/iCPWpRMTEsIW5kM1JSO3ISlnma
 diyil1hefGTJY8aCqGApthfX4fyZK98oCV6zojxpCZfFPdsa+vf5n1RQ143odnOk
 6NSfXHYLI+2e+mJ1lw4GdpZdF+rF+7jWsUYC5EDNmvlIJYiKmm13whSQeWO0NHo8
 oD0pYboSIWnmdXx4s3RbWF2+Y28O1+oJDKZfXabB8DjVwtvlGnmWBRhgKji2e6E6
 Hhct83YbDWtEpbNkXcWpnc5v5ynmAMTYTxADhinTGUtVQh3Q4wWduuoHK6IyeI4s
 dbfpO2Wh6N/5k3a4UoA69IcI2DzPzb2sIFWpdS8wuNv5xDhV2OmmY2PjTfq2w+Qz
 hEoMCNDUG6rQAYf4auXK5JjhI4CaG/mz/qjIibTUqGODYECzQQyvq+c2Gdq0S8O/
 CUHOgui6aHbyuhWmXlEzhhkjuvBQZYaTxCA+LGMzy8w7UY9m4n5L/fX9M9IfFsMH
 NFCPrUfmxKPQj/mHlhu7KHaTMUlQ0pTqV5flSwqsjstZ2QddvI5EAKiLwIEhg7/2
 RpnOZoiFIxykduEYLxeh
 =CfCl
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 4.5 cycle

Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.

New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
 Also associated minor changes.
   - Set the device buffer watermark based on the minimum watermark for all
     attached buffers rather than just the 'primary' one.
   - iio_buffer_init - only set the watermark default if one hasn't already
     been provided.  This allows simple support for devices with a fixed
     watermark.
   - read only attribute for watermark on fixed watermark devices.
   - add explicit buffer enable/disable callbacks to allow the buffer to
     do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.

New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc

New driver features
* mma8452
  - support either of the available interrupt pins to cope with the case
    where board layout has lead to a particular one being connected.

Staging graduation
* Dummy driver
  - this driver acts as both an example and a test device for those with
    out hardware to develop userspace code against.

Cleanups and minor bits and bobs.
* treewide
  - Sort out the ordering of iio_device_register/unregister vs runtime
    pm function calls so that it's all nice and consistent and not race
    prone.
  - Check sscanf return values.  None of the cases will actually happen as
    the strings are supplied internally, but best to be consistent on this.
* ad7780
  - switch over to the gpio descriptor interface and remove the now unused
    platform data which gets rid of a header entirely.
* ad7793
  - drop a pointless else statement.
* at91_adc
  - Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
  - get rid of some commented out lines that snuck in during the move of
    the driver.
* lm3533-als
  - Print an error message on provision of an invalid resistance.
* mcp320x
  - Add compatible strings with vendor prefix and deprecate those with
    no vendor prefix.
* mxs-lradc
  - Use BIT macro in various places rather than shifted ones.
* pa12203001
  - Power off the chip if the registration fails.
* pulsedlight-lidar-lite
  - add runtime PM support.
* xilinx XADC
  - constify an iio_buffer_setup_ops structure.
2015-12-01 09:13:29 -08:00
Matt Ranostay 4ac4e086fd iio: pulsedlight-lidar-lite: add runtime PM
Add runtime PM support for the lidar-lite module to enable low power
mode when last device requested reading is over a second.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-11-22 12:18:47 +00:00
Matt Ranostay 45a6b8218d iio: lidar: return -EINVAL on invalid signal
Returning zero from the measurment function has the side effect of
corrupting the triggered buffer readings, better to use -EINVAL than
a zero measurement reading.

The INVALID status happens even it isn't out of range
sometimes roughly once every second or two. This can be from an
invalid second signal return path. Hence there are spurious zero
readings from the triggered buffer, and warning messages in the kernel
log.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-11-21 15:56:53 +00:00
Linus Torvalds 75f5db39ff spi: Updates for v4.4
Quite a lot of activity in SPI this cycle, almost all of it in drivers
 with a few minor improvements and tweaks in the core.
 
  - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
  - Support for big endian in the bcm63xx driver.
  - Multiple slave support for the mt8173
  - New driver for the auxiliary SPI controller in bcm2835 SoCs.
  - Support for Layerscale SoCs in the Freescale DSPI driver.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
 sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
 iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
 hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
 BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
 TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
 =DgXG
 -----END PGP SIGNATURE-----

Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Quite a lot of activity in SPI this cycle, almost all of it in drivers
  with a few minor improvements and tweaks in the core.

   - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
   - Support for big endian in the bcm63xx driver.
   - Multiple slave support for the mt8173
   - New driver for the auxiliary SPI controller in bcm2835 SoCs.
   - Support for Layerscale SoCs in the Freescale DSPI driver"

* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
  spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
  spi: pxa2xx: Add support for Intel Broxton
  spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
  spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
  spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
  spi: Add DSPI support for layerscape family
  spi: ti-qspi: improve ->remove() callback
  spi/spi-xilinx: Fix race condition on last word read
  spi: Drop owner assignment from spi_drivers
  spi: Add THIS_MODULE to spi_driver in SPI core
  spi: Setup the master controller driver before setting the chipselect
  spi: dw: replace magic constant by DW_SPI_DR
  spi: mediatek: mt8173 spi multiple devices support
  spi: mediatek: handle controller_data in mtk_spi_setup
  spi: mediatek: remove mtk_spi_config
  spi: mediatek: Update document devicetree bindings to support multiple devices
  spi: fix kernel-doc warnings about missing return desc in spi.c
  spi: fix kernel-doc warnings about missing return desc in spi.h
  spi: pxa2xx: Align a few defines
  spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
  ...
2015-11-05 13:15:12 -08:00
Andrew F. Davis 3821a065f5 spi: Drop owner assignment from spi_drivers
An spi_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-28 10:30:17 +09:00
Octavian Purdila 0f0796509c iio: remove gpio interrupt probing from drivers that use a single interrupt
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-10-03 12:05:51 +01:00
Matt Ranostay 80cf2b5ca4 iio: lidar: add missing MODULE_DEVICE_TABLE for dt
The device tree compatible strings weren't properly
registered for the pulsedlight-lidar-lite-v2 driver.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-09-30 18:20:53 +01:00
Matt Ranostay cb119d5350 iio: proximity: add support for PulsedLight LIDAR
Add support for the PulsedLight LIDAR rangefinder sensor which allows
high speed (over 300Hz) distance measurements using Barker Coding within
40 meter range.

Support only tested on the "blue label" rev 2, but may work using low
sample frequencies on the original version.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-08-31 16:48:16 +01:00
Javier Martinez Canillas 8b7c826d03 iio: as3935: Add OF match table
The Documentation/devicetree/bindings/iio/proximity/as3935.txt DT binding
doc lists "ams,as3935" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the SPI
core can do an OF style match.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-08-22 19:01:03 +01:00
Greg Kroah-Hartman 8c5dfdbbeb Second set of IIO fixes for the 4.2 cycle. Note these depend (mostly) on
material in the recent merge window, hence their separation from set (a)
 as the fixes-togreg branch predated the merge window.  I am running rather
 later with these than I would have liked hence the large set.
 
 * stk3310 fixes from Hartmut's review that came in post merge
   - fix direction of proximity inline with recent documentation
     clarification.
   - fix missing REGMAP_I2C dependency
   - rework the error handling for raw readings to fix an failure to power
     down in the event of a raw reading failing.
   - fix a bug in the compensation code which was toggling an extra bit in the
     register.
 * mmc35240 - reported samplign frequencies were wrong.
 * ltr501 fixes
   - fix a case of returning the return value of a regmap_read instead of
     the value read.
   - fix missing regmap dependency
 * sx9500 - fix missing default values for ret in a couple of places to handle
   the case of no enabled channels.
 * tmp006 - check that writes to info_mask elements are actually to writable
   ones.  Otherwise, writing to any of them will change the sampling frequency.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJVpCJ3AAoJEFSFNJnE9BaIN3gP/0bAfaLmR8zdnnBlUCr3VG1I
 xiXjzpcnzg8sZR0883AeqgnGpu2W4LNAIrVumNLBWOCifvN2HVdlcmIH5iHjHR+n
 r9Mp6RM9bBYWbUCmOZuaTOKHBMifh59cc8y3UkRsGAjr/EvpT5jciX4d60EvSE4d
 nQ2Fcg/kEYmyVZQ1UjfUZvbOwUcNJP2WhHsz30HGDFSCeCYkbtrDz2lcZqaSZSDV
 P/nJ3ySQtLIJ3OzyCKz9b212WrLODWc50CDQlcIFzKxaMqYytGndE88Zsvs0a1nx
 JPcSDK7zaMItPJ75PA+I5h7L4mMTOgReTrnQlpLP3YnlAdS8/1o2gz9dLnI2Y7iC
 eBLOBFFwp/rgY6eHdcvjyiLmpGs1zl93tiZsVBvcQkJw74HG56xlemPzxN09tmLd
 gxlGztucdBhXh8/PAG9o5kSV7xcop2lftJP+jAV7rxpCbmi2use/2vejFi8qjFiE
 CekQxmEm32YakVnkNauz5iiUIgCUa5fZ++/G2nIg6F3iRlF8B6akUFdStCcwIc8b
 6vyF4jkKU+hyAu0TiWnjLHa83brlJ44L4TOPhhS3QvDbGpr8ULHdCrSBdwifZoBC
 0m6J0Tia6M/TmwQ+4Owd2MzNzX/YUbtd3b7nIje7QnEQu5UAe4F3Myio8uyWB8uR
 o/sfUmysDXQbKycJ0PEg
 =1kNg
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

Second set of IIO fixes for the 4.2 cycle. Note these depend (mostly) on
material in the recent merge window, hence their separation from set (a)
as the fixes-togreg branch predated the merge window.  I am running rather
later with these than I would have liked hence the large set.

* stk3310 fixes from Hartmut's review that came in post merge
  - fix direction of proximity inline with recent documentation
    clarification.
  - fix missing REGMAP_I2C dependency
  - rework the error handling for raw readings to fix an failure to power
    down in the event of a raw reading failing.
  - fix a bug in the compensation code which was toggling an extra bit in the
    register.
* mmc35240 - reported samplign frequencies were wrong.
* ltr501 fixes
  - fix a case of returning the return value of a regmap_read instead of
    the value read.
  - fix missing regmap dependency
* sx9500 - fix missing default values for ret in a couple of places to handle
  the case of no enabled channels.
* tmp006 - check that writes to info_mask elements are actually to writable
  ones.  Otherwise, writing to any of them will change the sampling frequency.
2015-07-13 14:19:22 -07:00
Greg Kroah-Hartman a732cd437b First set of IIO fixes for the 4.2 cycle.
* Fix a regression in hid sensors suspend time as a result of adding runtime
   pm.  The normal flow of waking up devices in order to go into suspend
   (given the devices are normally suspended when not reading) to a regression
   in suspend time on some laptops (reports of an additional 8 seconds).
   Fix this by checking to see if a user action resulting in the wake up, and
   make it a null operation if it didn't.  Note that for hid sensors, there is
   nothing useful to be done when moving into a full suspend from a runtime
   suspend so they might as well be left alone.
 * rochip_saradc: fix some missing MODULE_* data including the licence so that
   the driver does not taint the kernel incorrectly and can build as a module.
 * twl4030 - mark irq as oneshot as it always should have been.
 * inv-mpu - write formats for attributes not specified, leading to miss
   interpretation of the gyro scale channel when written.
 * Proximity ABI clarification.  This had snuck through as a mess.  Some
   drivers thought proximity went in one direction, some the other.  We went
   with the most common option, documented it and fixed up the drivers going
   the other way.  Fix for sx9500 included in this set.
 * ad624r - fix a wrong shift in the output data.
 * at91_adc - remove a false limit on the value of the STARTUP register
   applied by too small a type for the device tree parameter.
 * cm3323 - clear the bits when setting the integration time (otherwise
   we can only ever set more bits in the relevant field).
 * bmc150-accel - multiple triggers are registered, but on error were not being
   unwound in the opposite order leading to removal of triggers that had not
   yet successfully been registered (count down instead of up when unwinding).
 * tcs3414 - ensure right part of val / val2 pair read so that the integration
   time is not always 0.
 * cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJVpA2CAAoJEFSFNJnE9BaIJGEP/2uXFSqOZhmJ9sGqICSgKj4W
 OUjDtpXpKWxLC3Fypzvzg5u00R1t2likfvhXP2RsF5+/mqPb8NS6qzdcKMPCyxEl
 5tvsmYHm9yxN8o3ZZqtgYaR4mYt5tH4dFZ9qHpbFeNAXGjTRrYhGbgmLnND0v7cA
 5L1ABLls8ntoJ1aZZDsofwnmnUgclW5yqQZZ+huNkwaOpUQLke9tEL18cv+bsVgS
 zw7j/t3oJVdcUB9OTB7T/sW9J0+W7XnXogATHksHdHh2cd5N7wh/EZ1bet69QUrI
 PD2q2+0MUwyBMWDPveyWfm7XbS66lYxIRCmWZp+69Q1c/V91srhSPfh0kPcvHSQ1
 Uzpba6oSFPlFyDAtXWhaSEBzjXaHwKBIQvIVYOKiE6JdrbsnSg4GHAcF8TMhGtwT
 SDDgfb+cxOm6Vb4ws0+i15HMEiXpeK8AiJfHmLvau3OnA69/xzxHqqSg/oCO6/ES
 IzoAMqIVEk3L5gu88qgnmWzmyWp1pyTf1u+Kr+gAXNdSF/b3wgVkGn2X9hNRQ4g/
 XEFAD1PzarBnv1ce/HfWi+9/aUwv08nXHxBe4Yx3bfle2RUQKmFSbksVkCwu+ha3
 E4jPs5Cf9MrHO4gbuFaZX2+bFYlMdbcEWVRcP/3CHUuxeixGwemOsak1L+J5h6+e
 2xVEkGeywVdmDOsan1B8
 =mBqw
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First set of IIO fixes for the 4.2 cycle.

* Fix a regression in hid sensors suspend time as a result of adding runtime
  pm.  The normal flow of waking up devices in order to go into suspend
  (given the devices are normally suspended when not reading) to a regression
  in suspend time on some laptops (reports of an additional 8 seconds).
  Fix this by checking to see if a user action resulting in the wake up, and
  make it a null operation if it didn't.  Note that for hid sensors, there is
  nothing useful to be done when moving into a full suspend from a runtime
  suspend so they might as well be left alone.
* rochip_saradc: fix some missing MODULE_* data including the licence so that
  the driver does not taint the kernel incorrectly and can build as a module.
* twl4030 - mark irq as oneshot as it always should have been.
* inv-mpu - write formats for attributes not specified, leading to miss
  interpretation of the gyro scale channel when written.
* Proximity ABI clarification.  This had snuck through as a mess.  Some
  drivers thought proximity went in one direction, some the other.  We went
  with the most common option, documented it and fixed up the drivers going
  the other way.  Fix for sx9500 included in this set.
* ad624r - fix a wrong shift in the output data.
* at91_adc - remove a false limit on the value of the STARTUP register
  applied by too small a type for the device tree parameter.
* cm3323 - clear the bits when setting the integration time (otherwise
  we can only ever set more bits in the relevant field).
* bmc150-accel - multiple triggers are registered, but on error were not being
  unwound in the opposite order leading to removal of triggers that had not
  yet successfully been registered (count down instead of up when unwinding).
* tcs3414 - ensure right part of val / val2 pair read so that the integration
  time is not always 0.
* cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
2015-07-13 14:18:07 -07:00
Geert Uytterhoeven 897993fecb iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_preenable’:
drivers/iio/proximity/sx9500.c:682: warning: ‘ret’ may be used uninitialized in this function
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_predisable’:
drivers/iio/proximity/sx9500.c:706: warning: ‘ret’ may be used uninitialized in this function

If active_scan_mask is empty, it will loop once more over all channels,
doing nothing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-07-05 14:18:12 +01:00
Vlad Dogaru 68958bd5ca iio: sx9500: fix bug in compensation code
The initial compensation was mistakingly toggling an extra bit in the
control register.  Fix this and make sure it's less likely to happen by
introducing an additional macro.

Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-07-05 14:03:32 +01:00
Vlad Dogaru 657c7ff56f iio: sx9500: rework error handling of raw readings
Fix error handling so that we can power the chip down even if a raw read
fails.

Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-07-05 14:02:19 +01:00
Daniel Baluta fd1883f07c iio: proximity: sx9500: Fix proximity value
Because of the ABI confusion proximity value exposed by SX9500
was inverted.

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-06-13 19:19:27 +01:00
Jonathan Cameron 1a30295a09 iio:prox:sx9500 trivial simplification of return path in init function.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Vlad Dogaru <vlad.dogaru@intel.com>
2015-05-07 10:42:31 +01:00
Vlad Dogaru 45fd5f8e10 iio: sx9500: add GPIO reset pin
If a GPIO reset pin is listed in ACPI or Device Tree, use it to reset
the device on initialization.

Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-18 20:14:54 +01:00
Vlad Dogaru 821ace2929 iio: sx9500: refactor GPIO interrupt code
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-18 20:14:14 +01:00
Vlad Dogaru 59bd0427c0 iio: sx9500: optimize power usage
In the interest of lowering power usage, we only activate the proximity
channels and interrupts that we are currently using.

For raw reads, we activate the corresponding channel and the data ready
interrupt and wait for the interrupt to trigger.  If no interrupt is
available, we wait for the documented scan period, as specified in the
datasheet.

The following types of usage patterns may overlap:

* raw proximity reads (need a single data ready interrupt)
* trigger usage (needs data ready interrupts as long as active)
* proximity events (need near/far interrupts)
* triggered buffer reads (don't need any interrupts, but are usually
coupled with our own trigger.

To mitigate all possible patterns, we implement usage counting for all
the resources used: data ready interrupts, near/far interrupts and
individual channels.

The device enters sleep mode as documented in the data sheet when its
buffer, trigger and events are disabled, and no raw reads are currently
running.

Because of this new usage pattern, it is important that we give the
device a chance to perform an initial compensation for all its channels
at probe time.

Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-18 20:11:52 +01:00
Vlad Dogaru a40c0ac108 iio: sx9500: fix formatting
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-18 19:57:46 +01:00
Vlad Dogaru 63de9f92cc iio: sx9500: rename GPIO interrupt pin
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-18 19:57:45 +01:00
Vlad Dogaru 7840ffee97 iio: sx9500: add power management
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-04-09 17:12:59 +01:00
Greg Kroah-Hartman c610f7f772 Merge 4.0-rc7 into staging-next
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-07 11:03:02 +02:00
Octavian Purdila 70dddeee89 iio: fix drivers that check buffer->scan_mask
If the in-kernel push interface is used we may have a different masks
on the device buffer and the kernel buffer and in this case the device
should generate data for the reunion of the buffers, which is
available at indio_dev->active_scan_mask.

Compiled tested only except for bmc150-accel which was tested at
runtime with the hardware.

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-03-07 19:17:07 +00:00
Uwe Kleine-König b457f53a2a iio: improve usage of gpiod API
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-02-22 09:49:22 +00:00
Lars-Peter Clausen 9d9f780000 iio: as3935: Switch to PM ops
Switch from the legacy suspend/resume callbacks to device pm ops.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-01-27 18:49:52 +00:00
Greg Kroah-Hartman 6e49557b31 First round of IIO new drivers, cleanups and functionality for the 3.20 cycle take 2
Updated pull request with Daniel's fix on top for the power management
 Kconfig changes that had snuck in since last update of the IIO tree
 worked it's way through from mainline.
 
 Original pull message
 
 New device support
 * jsa1212 proxmity / ambient light sensor
 * SM08500 supported added to the kxcjk-1013 accelerometer driver
 * KMX61 Accelerometer/Magnetometer.  This took a somewhat rocky path
   being first merged, then reverted for a rewrite after a discussion of
   how to support additional functionality and finally being merged prior
   to some last reviews coming in, with resultant follow up patches.
 * Freescale mma9551l driver (minor follow up warning supression patch).
 * Semtech SX9500 proximity device driver.
 * ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
   for the ak09911.
 
 New functionality
  * Dummy driver gains some virtual registers making it more flexible.
  * IIO_ACTIVITY channel types, with modifiers running, walking etc.  This is
    to support on chip motion clasifiers.  As such it is in the form of a
    confidence percentage.  The only devices so far only do binary decisions
    but this gives us room when other devices give more nuanced clasification.
  * IIO_EV_DIR_NONE type for events where there is no obvious direction.
    First case is step detection.
  * IIO_STEPS channel type for pedometers.
  * ENABLE mask element used to control turning on counting types such as
    the pedometer that need a 'start point'.
  * INSTANCE event type to support things that happen once.
  * info element for height calibration (used in various motion estimation
    algorithms). Note heigh tof use
  * dummy driver demonstration of the use of all the new bits above.
  * event monitor support for the new events.
  * inv_mpu6050 gains an i2c mux to allow bypassing the device to access
    additional devices connected on the other side of it.  Note that in
    Windows these are handled by firmware on the device and not exposed
    directly.
  * inv_mpu6050 gains ACPI enumeration.
  * inkern interface gains iio_write_channel_raw to allow in kernel users
    of DAC functionality via a simple wrapper.
  * Document input current readings in the ABI docs.
  * Add an error message when we get an out of range error in device tree
    processing for the in kernel interfaces.  Basically a device tree debugging
    aid.
  * Add a sanity check that a scan index for a channel is unique during
    registration.  There to help catch bugs as this should never happen
    in a bug free driver.
 
 Cleanups and fixlets
 
  A rework of buffer registration from Lars - a precursor to some other
  upcoming new stuff (a few patches from others rolled in here as well).
  * Ensure all drivers register the same channels for the device and buffer.
  * Move buffer registration into the core rather than using the old
    two step approach.  Now we have simple ways of using a unified set channels
    for both without requiring channels be exposed by both interface, this
    removes a fair bit of boilerplate.
  * Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
    default. It has long be convention in IIO to startup with no channels
    enabled and leave it up to userspace to say what goes in the buffer.
    Getting rid of these allows us to drop export of iio_scan_mask_set.
  * Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
    for a while.
  * Allocate standard buffer attributes in the core rather than in every
    driver with a buffer.
  * Make the length attribute read only when a driver is not able to set
    the length.
  * Drop the get_length callback for buffers as it is already available in
    struct iio_buffer.
  * Drop an unused arguement form iio_kfifo_allocate and add devm allocator
    for it.
  * some kconfig entries gain anotation with the resulting module name.
  * Fix a resulting compile issue in dummy driver due to a stub taking
    wrong parameters as a result of the above rework.
  * Fix an off by 2 error in copying the core assigned buffer attributes.
 
 Other cleanups,
  * Trivial space before comma fixups.
  * ak8975 fixlets - none critical.  Rework to allow more device support.
  * Drop unnecessary sizeof(u8) calls.
  * bmp280 - refactor the compensation code to reduce copy operations and
    code length.  A second patch futher optimized this and performed some
    other minor cleanups.
  * kxcjk-1013 - various power control cleanups to avoid unnecessary enable
    / disable of device.  Make sure it is only controlled at all if CONFIG_PM
    is enabled.  Also som cleanups of error paths.
  * Small cleanups in adf4530 driver - pointless message and unnecessary braces.
  * Clarifiy the proximity ABI docs to make it clear it should get bigger
    as we move futher away.
  * Drop a misleading comment form industrialio-core.c
  * Trivial white space cleanups.
  * sca3000 looses an unused debug function.
  * Fix char unsigned ordering in ad8366
  * Increase the sleep time in ad9523 to make it predictable (value didn't
    really matter so make it more than 20 msecs)
  * mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
    the meet all the 'interesting' documentation.
  * A couple of cleanups for the staging ad5933 driver to avoid unnecessary
    conversion to a processed temperature vlaue in kernel and remove
    platform data form the state structure as not needed after probe.
  * Fix a wrong scale factor in the docs.
 
 Misc
  * Add IIO include files to the maintainers entry.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJUvtDlAAoJEFSFNJnE9BaIaNMQAI9ZYOrOmvSpxPV4ab71it9z
 gi03VG8+iJl0dPgwcSHeFZvSDiNAOWSX/XdWLoxFAdpjpsnytIp01s9+c3ogz58j
 pYbjxuOT2Qcf+36REuaFkQPFV2ppXMvwDwFUUNeFVupu+bVUKeZuNafBDp00aN1c
 o4MPDwoS1EcTHL+77iCg06exL8LozOwLabfUTRVIRkhIqikemghcmubQHH06m+dk
 EMddtNcXTVR4cJLX076nkKsNDHgmfoBYL9Hy/OvQbjWYAxoZg+q90ZX8yCy0Z5oW
 otChj5XpoYRIa7X6xvP5kTebD4iiR/COWer83EyqFosXhmQ/27rWasST42j1K3q/
 mU40skbscDef4F6COMlgBtVh1FhKUm9AHPAGk5swW792Qjpd4xdt+GShU5bJCa4O
 OOZYk8ulraELeWVz2IK+CrOvJYeTSrNQR6VA6sBjWRHeqxtB0yOJkhxX9NUcSIgJ
 GwM8qNTrQUkvI7OGvFGvf8hp9cboJTKEfzC+yspj+OJSjgJgNWw2pOjzJjsexxaL
 nT2rKhPg46hC+FR4IvPPjhGihCtMSgBWkwbHSeXH+TgRfbbTUh6y6sqEUZraVhnQ
 LKde54G0aH1XBFIM6fwWIPgdWBWsI3b3pFuBRMzhORdcCuAUOvDSyc5hVcaA8qb5
 UZghapUruB556xjoMV3n
 =LlJD
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-3.20a_take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

First round of IIO new drivers, cleanups and functionality for the 3.20 cycle take 2

Updated pull request with Daniel's fix on top for the power management
Kconfig changes that had snuck in since last update of the IIO tree
worked it's way through from mainline.

Original pull message

New device support
* jsa1212 proxmity / ambient light sensor
* SM08500 supported added to the kxcjk-1013 accelerometer driver
* KMX61 Accelerometer/Magnetometer.  This took a somewhat rocky path
  being first merged, then reverted for a rewrite after a discussion of
  how to support additional functionality and finally being merged prior
  to some last reviews coming in, with resultant follow up patches.
* Freescale mma9551l driver (minor follow up warning supression patch).
* Semtech SX9500 proximity device driver.
* ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
  for the ak09911.

New functionality
 * Dummy driver gains some virtual registers making it more flexible.
 * IIO_ACTIVITY channel types, with modifiers running, walking etc.  This is
   to support on chip motion clasifiers.  As such it is in the form of a
   confidence percentage.  The only devices so far only do binary decisions
   but this gives us room when other devices give more nuanced clasification.
 * IIO_EV_DIR_NONE type for events where there is no obvious direction.
   First case is step detection.
 * IIO_STEPS channel type for pedometers.
 * ENABLE mask element used to control turning on counting types such as
   the pedometer that need a 'start point'.
 * INSTANCE event type to support things that happen once.
 * info element for height calibration (used in various motion estimation
   algorithms). Note heigh tof use
 * dummy driver demonstration of the use of all the new bits above.
 * event monitor support for the new events.
 * inv_mpu6050 gains an i2c mux to allow bypassing the device to access
   additional devices connected on the other side of it.  Note that in
   Windows these are handled by firmware on the device and not exposed
   directly.
 * inv_mpu6050 gains ACPI enumeration.
 * inkern interface gains iio_write_channel_raw to allow in kernel users
   of DAC functionality via a simple wrapper.
 * Document input current readings in the ABI docs.
 * Add an error message when we get an out of range error in device tree
   processing for the in kernel interfaces.  Basically a device tree debugging
   aid.
 * Add a sanity check that a scan index for a channel is unique during
   registration.  There to help catch bugs as this should never happen
   in a bug free driver.

Cleanups and fixlets

 A rework of buffer registration from Lars - a precursor to some other
 upcoming new stuff (a few patches from others rolled in here as well).
 * Ensure all drivers register the same channels for the device and buffer.
 * Move buffer registration into the core rather than using the old
   two step approach.  Now we have simple ways of using a unified set channels
   for both without requiring channels be exposed by both interface, this
   removes a fair bit of boilerplate.
 * Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
   default. It has long be convention in IIO to startup with no channels
   enabled and leave it up to userspace to say what goes in the buffer.
   Getting rid of these allows us to drop export of iio_scan_mask_set.
 * Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
   for a while.
 * Allocate standard buffer attributes in the core rather than in every
   driver with a buffer.
 * Make the length attribute read only when a driver is not able to set
   the length.
 * Drop the get_length callback for buffers as it is already available in
   struct iio_buffer.
 * Drop an unused arguement form iio_kfifo_allocate and add devm allocator
   for it.
 * some kconfig entries gain anotation with the resulting module name.
 * Fix a resulting compile issue in dummy driver due to a stub taking
   wrong parameters as a result of the above rework.
 * Fix an off by 2 error in copying the core assigned buffer attributes.

Other cleanups,
 * Trivial space before comma fixups.
 * ak8975 fixlets - none critical.  Rework to allow more device support.
 * Drop unnecessary sizeof(u8) calls.
 * bmp280 - refactor the compensation code to reduce copy operations and
   code length.  A second patch futher optimized this and performed some
   other minor cleanups.
 * kxcjk-1013 - various power control cleanups to avoid unnecessary enable
   / disable of device.  Make sure it is only controlled at all if CONFIG_PM
   is enabled.  Also som cleanups of error paths.
 * Small cleanups in adf4530 driver - pointless message and unnecessary braces.
 * Clarifiy the proximity ABI docs to make it clear it should get bigger
   as we move futher away.
 * Drop a misleading comment form industrialio-core.c
 * Trivial white space cleanups.
 * sca3000 looses an unused debug function.
 * Fix char unsigned ordering in ad8366
 * Increase the sleep time in ad9523 to make it predictable (value didn't
   really matter so make it more than 20 msecs)
 * mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
   the meet all the 'interesting' documentation.
 * A couple of cleanups for the staging ad5933 driver to avoid unnecessary
   conversion to a processed temperature vlaue in kernel and remove
   platform data form the state structure as not needed after probe.
 * Fix a wrong scale factor in the docs.

Misc
 * Add IIO include files to the maintainers entry.
2015-01-21 10:13:37 +08:00
Vlad Dogaru 4193c0f1d8 iio: driver for Semtech SX9500 proximity solution
Supports buffering, IIO events and changing sampling frequency.

Datasheet available at:
http://www.semtech.com/images/datasheet/sx9500_ag.pdf

Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2015-01-05 18:59:42 +00:00
Greg Kroah-Hartman cc03f9bc26 Merge 3.18-rc4 into staging-next
We want the staging fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-10 12:24:26 +09:00
George McCollister f73cde600d iio: as3935: allocate correct iio_device size
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-11-05 18:33:46 +00:00
George McCollister 455f0049e0 iio: as3935: Remove unnecessary semicolons
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-11-05 13:47:42 +00:00
Peter Meerwald 398fd22b6b iio: Remove timestamp argument from iio_trigger_poll() and iio_trigger_poll_chained()
argument has been ignored; adjust drivers accordingly

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-06-14 16:25:59 +01:00
Matt Ranostay 24ddb0e4bb iio: Add AS3935 lightning sensor support
AS3935 chipset can detect lightning strikes and reports those back as
events and the estimated distance to the storm.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-03-16 18:00:32 +00:00