Commit Graph

18 Commits

Author SHA1 Message Date
Andy Shevchenko 6731ca3999 iio: st_sensors: Add lsm9ds0 IMU support
We can utilize separate drivers for accelerometer and magnetometer,
so here is the glue driver to enable LSM9DS0 IMU support.

The idea was suggested by Crestez Dan Leonard in [1]. The proposed change
was sent as RFC due to race condition concerns, which are indeed possible.

In order to amend the initial change, I went further by providing a specific
multi-instantiate probe driver that reuses existing accelerometer and
magnetometer.

[1]: https://lore.kernel.org/patchwork/patch/670353/

Suggested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: mr.lahorde@laposte.net
Cc: Matija Podravec <matija_podravec@fastmail.fm>
Cc: Sergey Borishchenko <borischenko.sergey@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210414195454.84183-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-05-17 13:54:22 +01:00
Jean-Baptiste Maneyrol 8237945dbc iio: imu: add Kconfig and Makefile for inv_icm42600 driver
Add 3 modules: inv-icm42600, inv-icm42600-i2c, inv-icm42600-spi.

Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2020-06-27 14:20:25 +01:00
Nuno Sá fff7352bf7 iio: imu: Add support for adis16475
Support ADIS16475 and similar IMU devices. These devices are
a precision, miniature MEMS inertial measurement unit (IMU) that
includes a triaxial gyroscope and a triaxial accelerometer. Each
inertial sensor combines with signal conditioning that optimizes
dynamic performance.

The driver adds support for the following devices:
* adis16470, adis16475, adis16477, adis16465, adis16467, adis16500,
  adis16505, adis16507.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2020-05-03 09:47:18 +01:00
Robert Jones 84e5ddd5c4 iio: imu: Add support for the FXOS8700 IMU
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.

FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.

TODO: Trigger and IRQ configuration support

Datasheet:
  http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf

Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-10-22 10:24:50 +01:00
Alexandru Ardelean db6ed4d23d iio: imu: Add support for the ADIS16460 IMU
The ADIS16460 device is a complete inertial system that includes a triaxial
gyroscope and a triaxial accelerometer. It's more simplified design than
that of the ADIS16480, and does not offer the triaxial magnetometers &
pressure sensors. It does also have a temperature sensor (like the
ADIS16480).
Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS
library.

Naturally, the register map is different and much more simplified than the
ADIS16480 subfamily, so it cannot be integrated into that driver. A major
difference is that the registers are not paged.

One thing that is particularly special about it, is that it requires a
higher delay between CS changes (i.e. when CS goes up, the spec recommends
that it be brought down after a minimum of 16 uS).
Other ADIS chips require (via spec) a minimum of 2 uS between CS changes.
The kernel's 10 uS default should be fine for those other chips; they
haven't been tested with lower CS change delays yet.

Datasheet:
  https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf

Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-07-27 22:52:06 +01:00
Thomas Gleixner ec8f24b7fa treewide: Add SPDX license identifier - Makefile/Kconfig
Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:46 +02:00
Lorenzo Bianconi 290a6ce11d iio: imu: add support to lsm6dsx driver
Add support to STM LSM6DS3-LSM6DSM 6-axis (acc + gyro) Mems sensor

http://www.st.com/resource/en/datasheet/lsm6ds3.pdf
http://www.st.com/resource/en/datasheet/lsm6dsm.pdf

- continuous mode support
- i2c support
- spi support
- sw fifo mode support
- supported devices: lsm6ds3, lsm6dsm

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-14 12:40:37 +00:00
Daniel Baluta 77c4ad2d6a iio: imu: Add initial support for Bosch BMI160
BMI160 is an Inertial Measurement Unit (IMU) which provides acceleration
and angular rate measurement. It also offers a secondary I2C interface
for connecting a magnetometer sensor (usually BMM160).

Current driver offers support for accelerometer and gyroscope readings
via sysfs or via buffer interface using an external trigger (e.g.
hrtimer). Data is retrieved from IMU via I2C or SPI interface.

Datasheet is at:
	http://www.mouser.com/ds/2/783/BST-BMI160-DS000-07-786474.pdf

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-04-16 13:39:21 +01:00
Daniel Baluta c3a23ecc09 iio: imu: kmx61: Add support for data ready triggers
This creates a data ready trigger per IIO device.

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-12-12 13:49:30 +00:00
Daniel Baluta 20ffac278e iio: imu: Add support for Kionix KMX61 sensor
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.

This driver uses two IIO devices one for accelerometer and one for magnetometer.

Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-12-12 13:43:54 +00:00
Jonathan Cameron 3909a0713e Revert "iio: imu: Add support for Kionix KMX61 sensor"
The two halves of this part can run largely independently.  Hence
a version 4 of this patch followed that reorganized things completely.

This reverts commit d7d787d291.
2014-12-12 13:30:04 +00:00
Daniel Baluta d7d787d291 iio: imu: Add support for Kionix KMX61 sensor
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.

Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-11-22 10:47:20 +00:00
Manuel Stahl ed10557fce iio: imu: mpu6050: Move config entry into IMU menu
Signed-off-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-08 12:27:30 +00:00
Lars-Peter Clausen 3edc84e605 iio: Add a comment to about alphabetical order to Kconfigs and Makefiles
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.

Also reorder those  entries which weren't in alphabetical order yet.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-08-03 18:40:36 +01:00
Ge Gao 09a642b785 Invensense MPU6050 Device Driver.
This the basic functional Invensense MPU6050 Device driver.

Signed-off-by: Ge Gao <ggao@invensense.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-02-10 17:42:43 +00:00
Lars-Peter Clausen d6b09bd85d staging:iio: Move adis16400 out of staging
This adis16400 driver is in pretty good shape now, so move it out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2013-01-26 10:07:50 +00:00
Lars-Peter Clausen 2f3abe6cbb iio:imu: Add support for the ADIS16480 and similar IMUs
This patch adds support for the ADIS16375, ADIS16480, ADIS16485, ADIS16488 6
degree to 10 degree of freedom IMUs.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2012-11-20 21:28:51 +00:00
Lars-Peter Clausen ec04cb048d staging:iio: Move adis library out of staging
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.

While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2012-11-19 22:22:12 +00:00