BACO feature must be kept enabled to allow entry into
BACO state in SMU during runtime suspend.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To quickly validate whether DMCUB is running and accepting commands for
offload testing we want to intercept a common sequence as part of
modeset programming.
[How]
OTG enable will cause the most impact in terms of golden register
changes and it's a single register write.
This approach was previously done in dcn10 code when it was shared with
dcn20 but it wasn't ported over to the dcn20 code.
Port over start, execute and wait sequence into dcn20_optc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When setting lttpr mode, the new mode to bet is not logged properly.
[How]
Update log message to show the right mode.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for further changes
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we require HDR_MULT >= 1.0
There are scenarios where we need < 1.0
[How]
Only guard against 0 - it will black-screen image.
It is up to higher-level logic to decide what HDR_MULT
values are allowed in each particular case.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen tearing is present in tests when setting the frame rate to
certain fps
[How]
Revert previous optimizations for low frame rates.
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor position needs to take into account plane scaling as well.
[How]
Translate cursor coords from stream space to plane space.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is causing green Line at the bottom of SDR 480p
MPO playback
[How]
Limit workaround to vertical > 512
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc needs to expose its internal dsc policy.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add_dsc_to_stream_resource could be called for validation.
Failing validation is completely fine.
However failing it inside commit streams is bad.
This code could be triggered for both contexts.
The function itself cannot distinguish the caller, which
makes it impossible to output the log only in the
meaningful case (commit streams).
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to support 6 bpp for 420 pixel encoding only.
[how]
Add a dc function to determine what bpp range can be supported
for given pixel encoding.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we don't need this call of program_front_end, as
earlier and later calls in the same sequence are sufficient.
[How]
Remove first call of program_front_end in dc_commit_state_no_check.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we may need to check for mpcc idle in more cases
than just when opp_changed is true. Also, mpcc_inst is equal to
pipe_idx, so remove for loop.
[How]
Remove opp_changed flag check and mpcc_inst loop.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When training with repeater the aux read interval must be set to
repeater specific aux_red_interval. This value is always 100us for CR.
[How]
Check for repeater when setting the aux_rd_interval in channel
equalization.
Use the right offset in the aux_rd_interval array
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPCC programming was being missed during certain split pipe enables due
to full_update flag not being true. This caused a momentary flash on
half the screen. After discussion, determined we should not have that
flag check within update_mpcc, as it should always perform full
programming when called.
[How]
Remove flag check. We call update_blending within insert_plane, so we
do not need to replace its call from the if block.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized sr latency numbers, for lpddr4
[How]
change the sr laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scratch registers are limited on the DMCUB and we have an expanding
list of state to track between driver and DMCUB.
[How]
Place shared state in cache window 6. The cache window size is aligned
to the size of the cache line on the DMCUB to make it easy to
invalidate.
The shared state is intended to be read only from driver side so
it's been marked as const.
The use of volatile is intentional. The memory for the shared firmware
state is memory mapped from the framebuffer memory. The DMCUB will
flush its cache after modifying the region. There's no way for x86
to known whether this data is stale or not so we want to intentionally
disable optimization to force the read at every access.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Commands will be considered a stable ABI between driver and firmware.
Commands are also split between DC commands, DAL feature commands,
and VBIOS commands.
Commands are currently not designated to a specific ID and the enum
does not provide a stable ABI.
We currently group all of these into a single command type of 8-bits.
With the stable ABI consideration in mind it's not unreasonable to
run out of command IDs.
For cleaner separation and versioning split the commands into a main
type and a subtype.
[How]
For commands where performance matters (like reg sequences) these
are still considered main commands.
Sub commands will be split by ownership/feature.
Update existing command sequences to reflect new changes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The function is expected to return instance of the timing generator
therefore we shouldn't be returning boolean in integer function,
and we shouldn't be returning zero so changing it to -1.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link setting will be modify after disable phy
and due to DP Compliance Fails.
[How]
Save and resotre link setting for disable link phy when link retraining.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to know DP protocol version
[How]
In DC create we initialize a cap to indicate the max
DP protocol version supported
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers, for lpddr4
[How]
change the p-state laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bring this calculation in line with HW programming guide.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous Renoir chroma viewport workaround fixed an MPO flicker by
increasing the chroma viewport size. However, when the MPO plane is
rotated 180 degrees, the viewport is read in reverse. Since the workaround
increases viewport size, when reading in reverse it causes a vertical
chroma offset.
[HOW]
Pass rotation value to viewport set functions
Temporarily disable the chroma viewport w/a when hubp is rotated 180 degrees
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On dcn21 this is programmed for tracebuffer support but isn't being
programmed on dcn20.
DMCUB execution hits an undefined address 65000000 on tracebuffer
access.
[How]
Program CW5.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not having support for autoload isn't an error. If the DMUB firmware
doesn't support it then don't return DMUB_STATUS_INVALID.
[How]
Return DMUB_STATUS_OK when ->is_auto_load_done is NULL.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait for PHY init won't finish if the firmware doesn't support it.
[How]
Only hook this functionality up on DCN21 and move it out of DCN20.
For ASIC without support then this should return OK so we don't hang
while waiting in DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screen seen after display is disabled then re-enabled.
Caused by difference in link settings when
switching between different resolutions.
[How]
In PnP case, or whenever the display is
still enabled but the driver is unloaded,
disable link before re-enabling with new link settings.
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training failed randomly when plugging USB-C display in/out.
[How]
If link training failed, reset PHY in link re-training.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong guards were causing the debug option not to run.
[How]
Changed the guard to the correct one, matching the rq, ttu, dlg regs struct
members that need to be guarded. Also log a message when validation starts.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Dali is currently being misinterpreted as Renoir,
as a result uses wrong clk mgr constructor
[HOW]
Add check to init Dali as Raven2 before it can be misidentified
Clean up & fix Raven2 & Dali ASIC checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some function pointers in the hwss function pointer table are
meant to be hw sequencer entry points to be called from dc.
However some of those function pointers are not meant to
be entry points, but instead used as a code reuse/inheritance
tool called directly by other hwss functions, not by dc.
Therefore, we want a more clear separation of which functions
we determine to be interface functions vs the functions we
use within hwss.
[How]
DC interface functions will be stored in:
struct hw_sequencer_funcs
Functions used within HWSS will be stored in:
struct hwseq_private_funcs
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Andrey Grodzovsky