glibc keeps getting cleverer, and my version now turns raise() into
more than one syscall. Since the test relies on ptrace seeing an
exact set of syscalls, this breaks the test. Replace raise(SIGSTOP)
with syscall(SYS_tgkill, ...) to force glibc to get out of our way.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/bc80338b453afa187bc5f895bd8e2c8d6e264da2.1521300271.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:
microcode: microcode_reload_late: late_cpus: 4
microcode: __reload_late: cpu 2 entered
microcode: __reload_late: cpu 1 entered
microcode: __reload_late: cpu 3 entered
microcode: __reload_late: cpu 0 entered
microcode: __reload_late: cpu 1 left
microcode: Timeout while waiting for CPUs rendezvous, remaining: 1
CPU1 above would finish, leave and the others will still spin waiting for
it to join.
So do two synchronization atomics instead, which makes the code a lot more
straightforward.
Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.
That's ok because the moment all CPUs are done, that timeout will be cut
short.
Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.
Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-2-bp@alien8.de
Return UCODE_NEW from the scanning functions to denote that new microcode
was found and only then attempt the expensive synchronization dance.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-1-bp@alien8.de
In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.
Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain
The kbuild test robot reported the following warning on sparc64:
kernel/jump_label.c: In function '__jump_label_update':
kernel/jump_label.c:376:51: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
WARN_ONCE(1, "can't patch jump_label at %pS", (void *)entry->code);
On sparc64, the jump_label entry->code field is of type u32, but
pointers are 64-bit. Silence the warning by casting entry->code to an
unsigned long before casting it to a pointer. This is also what the
sparc jump label code does.
Fixes: dc1dd184c2 ("jump_label: Warn on failed jump_label patching attempt")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: "David S . Miller" <davem@davemloft.net>
Link: https://lkml.kernel.org/r/c966fed42be6611254a62d46579ec7416548d572.1521041026.git.jpoimboe@redhat.com
In the following commit:
9e0e3c5130 ("x86/speculation, objtool: Annotate indirect calls/jumps for objtool")
... we added annotations for CALL_NOSPEC/JMP_NOSPEC on 64-bit x86 kernels,
but we did not annotate the 32-bit path.
Annotate it similarly.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180314112427.22351-1-apw@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
POPF would trap if VIP was set regardless of whether IF was set. Fix it.
Suggested-by: Stas Sergeev <stsp@list.ru>
Reported-by: Bart Oldeman <bartoldeman@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 5ed92a8ab7 ("x86/vm86: Use the normal pt_regs area for vm86")
Link: http://lkml.kernel.org/r/ce95f40556e7b2178b6bc06ee9557827ff94bd28.1521003603.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
POPF is currently broken -- add tests to catch the error. This
results in:
[RUN] POPF with VIP set and IF clear from vm86 mode
[INFO] Exited vm86 mode due to STI
[FAIL] Incorrect return reason (started at eip = 0xd, ended at eip = 0xf)
because POPF currently fails to check IF before reporting a pending
interrupt.
This patch also makes the FAIL message a bit more informative.
Reported-by: Bart Oldeman <bartoldeman@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/a16270b5cfe7832d6d00c479d0f871066cbdb52b.1521003603.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a logic error that caused the test to exit with 0 even if test
cases failed.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bartoldeman@gmail.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/b1cc37144038958a469c8f70a5f47a6a5638636a.1521003603.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Disable the kprobe probing of the entry trampoline:
.entry_trampoline is a code area that is used to ensure page table
isolation between userspace and kernelspace.
At the beginning of the execution of the trampoline, we load the
kernel's CR3 register. This has the effect of enabling the translation
of the kernel virtual addresses to physical addresses. Before this
happens most kernel addresses can not be translated because the running
process' CR3 is still used.
If a kprobe is placed on the trampoline code before that change of the
CR3 register happens the kernel crashes because int3 handling pages are
not accessible.
To fix this, add the .entry_trampoline section to the kprobe blacklist
to prohibit the probing of code before all the kernel pages are
accessible.
Signed-off-by: Francis Deslauriers <francis.deslauriers@efficios.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: mathieu.desnoyers@efficios.com
Cc: mhiramat@kernel.org
Link: http://lkml.kernel.org/r/1520565492-4637-2-git-send-email-francis.deslauriers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Original idea by Ashok, completely rewritten by Borislav.
Before you read any further: the early loading method is still the
preferred one and you should always do that. The following patch is
improving the late loading mechanism for long running jobs and cloud use
cases.
Gather all cores and serialize the microcode update on them by doing it
one-by-one to make the late update process as reliable as possible and
avoid potential issues caused by the microcode update.
[ Borislav: Rewrite completely. ]
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-8-bp@alien8.de
... so that any newer version can land in the cache and can later be
fished out by the application functions. Do that before grabbing the
hotplug lock.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-7-bp@alien8.de
The cache might contain a newer patch - look in there first.
A follow-on change will make sure newest patches are loaded into the
cache of microcode patches.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-6-bp@alien8.de
Avoid loading microcode if any of the CPUs are offline, and issue a
warning. Having different microcode revisions on the system at any time
is outright dangerous.
[ Borislav: Massage changelog. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-4-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-5-bp@alien8.de
Updating microcode is less error prone when caches have been flushed and
depending on what exactly the microcode is updating. For example, some
of the issues around certain Broadwell parts can be addressed by doing a
full cache flush.
[ Borislav: Massage it and use native_wbinvd() in both cases. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-3-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-4-bp@alien8.de
After updating microcode on one of the threads of a core, the other
thread sibling automatically gets the update since the microcode
resources on a hyperthreaded core are shared between the two threads.
Check the microcode revision on the CPU before performing a microcode
update and thus save us the WRMSR 0x79 because it is a particularly
expensive operation.
[ Borislav: Massage changelog and coding style. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-2-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-3-bp@alien8.de
It is a useless remnant from earlier times. Use the ucode_state enum
directly.
No functional change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-2-bp@alien8.de
As:
1) It's known that hypervisors lie about the environment anyhow (host
mismatch)
2) Even if the hypervisor (Xen, KVM, VMWare, etc) provided a valid
"correct" value, it all gets to be very murky when migration happens
(do you provide the "new" microcode of the machine?).
And in reality the cloud vendors are the ones that should make sure that
the microcode that is running is correct and we should just sing lalalala
and trust them.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: kvm <kvm@vger.kernel.org>
Cc: Krčmář <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226213019.GE9497@char.us.oracle.com
Since Linux v3.2, vsyscalls have been deprecated and slow. From v3.2
on, Linux had three vsyscall modes: "native", "emulate", and "none".
"emulate" is the default. All known user programs work correctly in
emulate mode, but vsyscalls turn into page faults and are emulated.
This is very slow. In "native" mode, the vsyscall page is easily
usable as an exploit gadget, but vsyscalls are a bit faster -- they
turn into normal syscalls. (This is in contrast to vDSO functions,
which can be much faster than syscalls.) In "none" mode, there are
no vsyscalls.
For all practical purposes, "native" was really just a chicken bit
in case something went wrong with the emulation. It's been over six
years, and nothing has gone wrong. Delete it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/519fee5268faea09ae550776ce969fa6e88668b0.1520449896.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As %rdi is never user except in the following push, there is no
need to restore %rdi to the original value.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@amacapital.net
Cc: viro@zeniv.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the CPU renaming registers on its own, and all the overhead of the
syscall entry/exit, it is doubtful whether the compiled output of
mov %r8, %rax
mov %rcx, %r8
mov %rax, %rcx
jmpq sys_clone
is measurably slower than the hand-crafted version of
xchg %r8, %rcx
So get rid of this special case.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@amacapital.net
Cc: viro@zeniv.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using SYSCALL_DEFINEx() is recommended, so use it also here.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@amacapital.net
Cc: viro@zeniv.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the compat entry point is equivalent to the native entry point, it
does not need to be specified explicitly.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@amacapital.net
Cc: viro@zeniv.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix the objtool build when cross-compiling a 64-bit kernel on a 32-bit
host. This also simplifies read_retpoline_hints() a bit and makes its
implementation similar to most of the other annotation reading
functions.
Reported-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: b5bc2231b8 ("objtool: Add retpoline validation")
Link: http://lkml.kernel.org/r/2ca46c636c23aa9c9d57d53c75de4ee3ddf7a7df.1520380691.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The separation of the cpu_entry_area from the fixmap missed the fact that
on 32bit non-PAE kernels the cpu_entry_area mapping might not be covered in
initial_page_table by the previous synchronizations.
This results in suspend/resume failures because 32bit utilizes initial page
table for resume. The absence of the cpu_entry_area mapping results in a
triple fault, aka. insta reboot.
With PAE enabled this works by chance because the PGD entry which covers
the fixmap and other parts incindentally provides the cpu_entry_area
mapping as well.
Synchronize the initial page table after setting up the cpu entry
area. Instead of adding yet another copy of the same code, move it to a
function and invoke it from the various places.
It needs to be investigated if the existing calls in setup_arch() and
setup_per_cpu_areas() can be replaced by the later invocation from
setup_cpu_entry_areas(), but that's beyond the scope of this fix.
Fixes: 92a0f81d89 ("x86/cpu_entry_area: Move it out of the fixmap")
Reported-by: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Woody Suwalski <terraluna977@gmail.com>
Cc: William Grant <william.grant@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802282137290.1392@nanos.tec.linutronix.de
Continue the switch table detection whack-a-mole. Add a check to
distinguish KASAN data reads from switch data reads. The switch jump
tables in .rodata have relocations associated with them.
This fixes the following warning:
crypto/asymmetric_keys/x509_cert_parser.o: warning: objtool: x509_note_pkey_algo()+0xa4: sibling call from callable instruction with modified stack frame
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/d7c8853022ad47d158cb81e953a40469fc08a95e.1519784382.git.jpoimboe@redhat.com
vmx_vcpu_run() and svm_vcpu_run() are large functions, and giving
branch hints to the compiler can actually make a substantial cycle
difference by keeping the fast path contiguous in memory.
With this optimization, the retpoline-guest/retpoline-host case is
about 50 cycles faster.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222154318.20361-3-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Having a paravirt indirect call in the IBRS restore path is not a
good idea, since we are trying to protect from speculative execution
of bogus indirect branch targets. It is also slower, so use
native_wrmsrl() on the vmentry path too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: d28b387fb7
Link: http://lkml.kernel.org/r/20180222154318.20361-2-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Disable retpoline validation in objtool if your compiler sucks, and otherwise
select the validation stuff for CONFIG_RETPOLINE=y (most builds would already
have it set due to ORC).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On 64-bit, the stack pointer is always aligned on interrupt, so instead
of setting the LSB of the pt_regs address, we can just add 1 to it.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180221024214.lhl5jfgw33c4vz3m@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert init_kernel_text() to a global function and use it in a few
places instead of manually comparing _sinittext and _einittext.
Note that kallsyms.h has a very similar function called
is_kernel_inittext(), but its end check is inclusive. I'm not sure
whether that's intentional behavior, so I didn't touch it.
Suggested-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4335d02be8d45ca7d265d2f174251d0b7ee6c5fd.1519051220.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently when the jump label code encounters an address which isn't
recognized by kernel_text_address(), it just silently fails.
This can be dangerous because jump labels are used in a variety of
places, and are generally expected to work. Convert the silent failure
to a warning.
This won't warn about attempted writes to tracepoints in __init code
after initmem has been freed, as those are already guarded by the
entry->code check.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/de3a271c93807adb7ed48f4e946b4f9156617680.1519051220.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After initmem has been freed, any jump labels in __init code are
prevented from being written to by the kernel_text_address() check in
__jump_label_update(). However, this check is quite broad. If
kernel_text_address() were to return false for any other reason, the
jump label write would fail silently with no warning.
For jump labels in module init code, entry->code is set to zero to
indicate that the entry is disabled. Do the same thing for core kernel
init code. This makes the behavior more consistent, and will also make
it more straightforward to detect non-init jump label write failures in
the next patch.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c52825c73f3a174e8398b6898284ec20d4deb126.1519051220.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Open-code the two instances which called switch_to_thread_stack(). This
allows us to remove the wrapper around DO_SWITCH_TO_THREAD_STACK.
While at it, update the UNWIND hint to reflect where the IRET frame is,
and update the commentary to reflect what we are actually doing here.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-7-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Moving ASM_CLAC to interrupt_entry means two instructions (addq / pushq
and call interrupt_entry) are not covered by it. However, it offers a
noticeable size reduction (-.2k):
text data bss dec hex filename
16882 0 0 16882 41f2 entry_64.o-orig
16623 0 0 16623 40ef entry_64.o
Suggested-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-6-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is now trivial to call interrupt_entry() and then the actual worker.
Therefore, remove the interrupt macro and open code it all.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-5-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We can also move the CLD, SWAPGS, and the switch_to_thread_stack() call
to the interrupt_entry() helper function. As we do not want call depths
of two, convert switch_to_thread_stack() to a macro.
However, switch_to_thread_stack() has another user in entry_64_compat.S,
which currently expects it to be a function. To keep the code changes
in this patch minimal, create a wrapper function.
The switch to a macro means that there is some binary code duplication
if CONFIG_IA32_EMULATION=y is enabled. Therefore, the size reduction
differs whether CONFIG_IA32_EMULATION is enabled or not:
CONFIG_IA32_EMULATION=y (-0.13k):
text data bss dec hex filename
17158 0 0 17158 4306 entry_64.o-orig
17028 0 0 17028 4284 entry_64.o
CONFIG_IA32_EMULATION=n (-0.27k):
text data bss dec hex filename
17158 0 0 17158 4306 entry_64.o-orig
16882 0 0 16882 41f2 entry_64.o
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-4-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Moving the switch to IRQ stack from the interrupt macro to the helper
function requires some trickery: All ENTER_IRQ_STACK really cares about
is where the "original" stack -- meaning the GP registers etc. -- is
stored. Therefore, we need to offset the stored RSP value by 8 whenever
ENTER_IRQ_STACK is called from within a function. In such cases, and
after switching to the IRQ stack, we need to push the "original" return
address (i.e. the return address from the call to the interrupt entry
function) to the IRQ stack.
This trickery allows us to carve another .85k from the text size (it
would be more except for the additional unwind hints):
text data bss dec hex filename
18006 0 0 18006 4656 entry_64.o-orig
17158 0 0 17158 4306 entry_64.o
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-3-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The PUSH_AND_CLEAR_REGS macro is able to insert the GP registers
"above" the original return address. This allows us to move a sizeable
part of the interrupt entry macro to an interrupt entry helper function:
text data bss dec hex filename
21088 0 0 21088 5260 entry_64.o-orig
18006 0 0 18006 4656 entry_64.o
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: dan.j.williams@intel.com
Link: http://lkml.kernel.org/r/20180220210113.6725-2-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
firmware_restrict_branch_speculation_*() recently started using
preempt_enable()/disable(), but those are relatively high level
primitives and cause build failures on some 32-bit builds.
Since we want to keep <asm/nospec-branch.h> low level, convert
them to macros to avoid header hell...
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: arjan.van.de.ven@intel.com
Cc: bp@alien8.de
Cc: dave.hansen@intel.com
Cc: jmattson@google.com
Cc: karahmed@amazon.de
Cc: kvm@vger.kernel.org
Cc: pbonzini@redhat.com
Cc: rkrcmar@redhat.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
David allowed retpolines in .init.text, except for modules, which will
trip up objtool retpoline validation, fix that.
Requested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
David requested a objtool validation pass for CONFIG_RETPOLINE=y enabled
builds, where it validates no unannotated indirect jumps or calls are
left.
Add an additional .discard.retpoline_safe section to allow annotating
the few indirect sites that are required and safe.
Requested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the existing global variables instead of passing them around and
creating duplicate global variables.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is boot code and thus Spectre-safe: we run this _way_ before userspace
comes along to have a chance to poison our branch predictor.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski