gl861: (MSI Megasky)
- hack for enable ZL10353 / QT1010 I2C gate
- use new QT1010 module instead of old code
au6610: (Sigmatek DVB-110)
- hack for enable ZL10353 / QT1010 I2C gate
- use new QT1010 module instead of old code
Tested successfully with au6610 and gl861 devices against fi-Yllas
frequencies. Now it locks perfectly with both devices.
There is a "hack" to enable probable i2c gate in zl10535
demodulator. QT1010 doesn't respond to any i2c messages before we
write 0x1a to demodulator register 0x62. In my understanding this
should be fixed to demodulator code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based
on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353)
demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar
as used in MSI Megasky GL861.
Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is
also supported by hw but I cannot test it due to lack of USB 1.1 port. Device
supports only isochronous mode transfers. There is also eeprom in usb
controller(at least in address range 0x80 - 0xbf) for storing data, eg.
firmware. Anyway, firmware loading is not used / required by the device.
There seems to be at least one unknown I2C device in address 0xa0, probably
remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07
from this unknown address.
Driver is based on gl861 module. Tuner has a lot of problems to lock with
megasky qt1010 module with this hardware with some broadcasting standards.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use parallel_ts - Now this driver works.
- correct typo in MODULE_VERSION
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove unneeded declaration of .generic_bulk_ctrl_endpoint
generic_bulk_ctrl_endpoint isn't being used in this device, so this
is not needed here.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky 580 based on gl861 has three endpoints:
- 0x81 BULK/ISOC IN MPEG2 TS
- 0x83 INT IN remote control receiver
- 0x02 BULK OUT bulk control endpoint
It doesn't look like the bulk endpoint is used, but better to
have the correct one in the config.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the DVB_USB_IS_AN_I2C_ADAPTER flag from the adapter
properties to the device properties.
Without this patch I get an OOPS when the gl861 driver tries to
access any registers.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gl861_tuner_attach function is not specific to this device.
This patch removes gl861_tuner_attach, and replaces it with
qt1010_tuner_attach from the qt1010 header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename driver_name from "gl861" to "dvb_usb_gl861"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The author's email address is already in the MODULE_AUTHOR field.
This patch adds his name as well.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the descriptions of "discovered" registers on the zl10353, using the
equivalaent mt352 register names.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement trl nominal rate calculation to Zarlink ZL10353 demod,
based on calculation used in Zarlink MT352.
This adds support for 6 and 8MHz bandwidth transponders.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement I2C gate control for Megasky GL861 and SigmaTek AU6610 support.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After studying many hours worth of register dumps of MT352 and ZL10353 fed
with identically damaged RF signals I have made an educated guess at which
registers contain the AGC level, bit error rate and uncorrectable error
count values.
Implement the IOCTLs that return these values to userspace.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
avoid double-up(), pointed out by Oliver.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb kernel_thread to kthread API port.
It is running fine here, including module load/unload and software suspend
(which doesn't work as expected with or without this patch :).
I didn't convert the dvb_ca_en50221 as I do not have such an interface, but
if the conversion process is fine with the v4l-dvb maintainers, it should not
be a problem to send a patch for that too ...
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes four needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed problem reported by Teemu Suikki:
After a device with subsystem 0x13c2:0x1012 has been installed,
devices with subsystem id 0x13c2:0x1011 did not work anymore.
Reason:
The driver for 0x13c2:0x1012 modified shared configuration data.
Fix:
Use separate configuration data for those devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
input_register_device() was changed to return an error code instead of
being void in 2.6.15. Handle it with a macro wrapper in config.h. For
this to work, linux/input.h must be included before config.h. This
required some trivial header re-ordering in budget-ci.c and ttusb_dec.c.
In kernel 2.6.15-rc1 a helper function called setup_timer() was added to
linux/timer.h. Add to compat.h, but require that linux/timer.h be
included first to give the definition of struct timer_list.
A new 4GB DMA zone, __GFP_DMA32, was added in 2.6.15-rc2. Alias it to
__GFP_DMA on older kernels.
Handle another 2.6.15 "input_dev->dev to input_dev->cdev.dev" change for
some recently added code in cinergyT2.c.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed unregistering the vbi device for cards without analog tuner.
Thanks to Marco Schluessler <marco@lordzodiac.de> for pointing out this bug.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add phys-string, bustype, version, vendor and product to help udev and
others using EVIOCPHYS ioctl to identify the input device node.
Code taken (with little changes) from budget-ci.c
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move filter caps from device caps to adapter caps for the megasky driver.
This fixes usb1.1 operation.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
QT1010:
- old qt1010-code totally rewritten and put in own kernel module
- same enhancements as my earlier QT1010 125kHz patch
- tuner initialization
- register 1f calculation
- register 20 calculation
- register 25 calculation
m920x: (MSI Megasky)
- use new QT1010 module instead of old code
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move .caps from the adapter properties to the device properties.
Thanks to Martin Schwier for confirming this fix.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes qt1010.h to use dvb_usb_device struct instead of a
dvb_usb_adapter for accessing the private area of the driver.
Without this patch my PC hard locks when an application tries to access
the DVB tuner.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky_tuner_attach function is not specific to this device.
This patch renames it to qt1010_tuner_attach and moves it into the qt1010
header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cleanups and suggestions from Patrick Boettcher.
Dropped the mutex in m9206_rc_query using #if 0, because
M9206_CORE, M9206_I2C, M9206_FILTER and M9206_FW can be accessed
concurrently.
Thanks to both Aapo Tahkola and Patrick Boettcher.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- hardware pid filtering no longer enabled unless in usb 1.x mode
- more responsive rc handling
- some minor bug fixes and code refolding
- m9206_write delay dropped (doesn't seem to be needed)
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
qt1010 is a tuner used in some other devices, so this code should be put
into a separate file so that it could be reused by other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
update code to use dvb_attach()
update code to reflect recent changes to the dvb_usb framework
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the driver works in bulk mode supporting both USB 2.0 and
1.0 with and without hardware pid filters.
The ULi m9205 also supports isochronous transfer mode, but I have
dropped support for it because it depends on firmware and does not work
on all USB host chips. Further, I have no firmware with remote
controller support for this mode.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I noticed that udev does not create a symlink for the CinergyT2 remote input
device in /dev/input/by-id, which is required if I want to have a
unique device name for lircd.
The attached patch tries to achive this. However, udev still omits the
input device for /dev/input/by-id symlinks. I think something is still
not reported correctly.
Signed-off-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The keymap is based on a previous patch by Jussi Kukkonen.
This remote is identified by subsystem_device id 0x1010.
Signed-off-by: Ville-Pekka Vainio <vpivaini@cs.helsinki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ultraview DVB-T Lite is a clone of DViCO FusionHDTV DVB-T Lite
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the initialization of alps tdee4 tuner in
flexcop-fe-tuner.c to match what is used in the old driver that was
written specifically for Cablestar cards by Patrick Boettcher. This
patch should make Cablestar2 work again with recent dvb drivers without
breaking other stv0297 based cards.
Signed-off-by: Antti Seppala <ajhseppa@niksula.hut.fi>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Second part of the patch to make the autosearch work again with DiB3000P/MC.
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
dvb_net.c: In function 'dvb_net_ule':
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 4 has type 'u32'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CRC-32 checking during ULE decapsulation always failed on x86_64 systems due
to the size of a variable used to store CRC. This bug was discovered on
Fedora Core 6 with kernel-2.6.18-1.2849. The i386 counterpart has no such
problem. This patch has been tested on 64-bit system as well as 32-bit system.
Signed-off-by: Ang Way Chuang <wcang@nrg.cs.usm.my>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes unnecessary (and misleading) debug
output (it printed the values of the keys in the table up to the value
of the key pressed).
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After rewriting the driver the wrong autosearch index was used when
COFDM-parameter needed to be detected.
Thanks to Mario Rossi who found it.
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix OMAP clock prescaler to match the comment
i2c: Refactor a kfree in i2c-dev
i2c: Fix return value check in i2c-dev
i2c: Enable PEC on more i2c-i801 devices
i2c: Discard the i2c algo del_bus wrappers
i2c: New ARM Versatile/Realview bus driver
i2c: fix broken ds1337 initialization
i2c: i2c-i801 documentation update
i2c: Use the __ATTR macro where possible
i2c: Whitespace cleanups
i2c: Use put_user instead of copy_to_user where possible
i2c: New Atmel AT91 bus driver
i2c: Add support for nested i2c bus locking
i2c: Cleanups to the i2c-nforce2 bus driver
i2c: Add request/release_mem_region to i2c-ibm_iic bus driver
i2c: New Philips PNX bus driver
i2c: Delete the broken i2c-ite bus driver
i2c: Update the list of driver IDs
i2c: Fix documentation typos
Converted dee1601, lgz201 and dtt8579 to use dvb_pll_attach
in dvb-usb-cxusb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes embedded log functions and makes use of the DVB math functions to
provide SNR in dB. The changes are modeled after recent changes made to
the LGDT330x frontends in lgdt330x.c
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes embedded log functions and makes use of the DVB math functions
to provide SNR in dB. The changes are modeled after recent changes made
to the LGDT330x frontends in lgdt330x.c
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove bogus read during MC1 programming.
A '1' bit could never be cleared using the old code.
Use MASK_xx macros.
Signed-off-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use SAA7146_IER_ENABLE/DISABLE to enable or disable a hardware interrupt.
Signed-off-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a delay to give the frontend a little bit time for power-on.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vendor IDs in this file were all in alphabetical
order except for this one.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/ttpci/budget-ci.c:220:6: warning: "LINUX_VERSION_CODE" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:28: warning: "KERNEL_VERSION" is not defined
drivers/media/dvb/ttpci/budget-ci.c:220:42: error: missing binary operator before token "("
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In some cases when using VSB, the AGC status register has been known to
falsely report "no signal" when in fact there is a carrier lock. The
datasheet labels these status flags as QAM only, yet the lgdt330x
module is using these flags for both QAM and VSB.
This patch allows for the carrier recovery lock status register to be
tested, even if the agc signal status register falsely reports no signal.
Thanks to jcrews from #linuxtv in irc, for initially reporting this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This caused compilation to fail - completely replaced by new style
functions, so can be removed.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If your device is using the philips tda1316 tuner, i think there is a
problem in setting the correct Band. 162 MHz and above should be band 2
(Mid-Band). But in dvbc_philips_tdm1316l_tuner_set_params band 1 is set
for frequencies below 200 MHz.
Signed-off-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the debounce logic so that it is not used at all unless the
debounce parameter has been set. This makes for a much "snappier" remote
for most users as there is no timeout to wait for (the debounce logic has
a 350ms timer for the next repeat, but with the RC5 protocol, one event
per ~110ms is possible)
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a ir_debug parameter which is useful in tracking down
IR decoding problems.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Decode the RC5 device byte as well as the command byte. Introduce a
parameter to set the device events to listen for. Default to try
to auto-detect the proper device code, otherwise, listen to any
device as the old code did.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This converts the budget-ci driver so that it uses ir-common for some of its
IR processing. In particular, the keymap for the Nova-T (sub 13c2:1011) is
switched to the Hauppauge grey/black keymap, of which the keys on the
supplied R808 remote control form a subset.
The old budget-ci keymap is moved to ir-keymaps.c and is used for other
remotes.
The debounce logic for buggy remotes (i.e. Zenith) is made conditional the
new debounce parameter and defaults to off (so that repeat keypresses aren't
ignored for all working remotes).
Some parts are based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trivial change to help the user understand what went wrong.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improve the error checking in the IR init and deinit functions.
Based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a 'phys' string, of the same form as used by various other
DVB cards' IR drivers, for access by any program which uses the EVIOCPHYS
ioctl or may read /sys/class/input/*/phys (e.g. udev) to identify input
device nodes.
Taken from Darren Salt's dvb-ir patchset.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch lays down some groundwork for later budget-ci patches. The bulk
of this consists of moving a few members into a new struct and renaming a
few of them.
It also allocates extra space for the device name (the "name" field in
/proc/bus/input/devices and in the relevant sysfs dir) to avoid truncation
and uses snprintf rather than sprintf in case the extra space shouldn't be
enough.
Taken from Darren Salt's dvb-ir patchset
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use return value of dvb_pll_configure() to fill priv->frequency
In lgh06xf_set_params:
Rename int variable "err" to "result".
Remove needless calculation of the set frequency, since this value is now
being returned by dvb_pll_configure().
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes some duplicated code by returning the frequency set by
dvb_pll_configure(), instead of recalculating it again in dvb_pll_set_params()
and dvb_pll_calc_regs().
If the return value of dvb_pll_configure is less than zero, it is an error
code. Otherwise, the return value is the frequency actually set by the
function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- adhere to 80-column limit
- replace some spaces with tabs
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for Pinnacle PCTV 400e DVB-S. The module name is called ttusb2,
because it this device (and other Pinnacle devices) is using the USB-protocol
originally used by Technotrend device. I'm suspecting Technotrend as the
device-designer.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a dump I2C message to the TDA826x-driver to fix I2C read for
identification with ttusb2-driver.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For some reason, some of these cards have the tda10021 configured to a
different address. This adds support for such cards
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also sprinkled some input_sync() throughout the code.
Acked-by: Ricardo Cerqueira <v4l@cerqueira.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We don't have to check for NULL before kfree()
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch creates a new atsc tuner module for the LG TDVS-H06xF ATSC tuners,
called lgh06xf. The purpose of this change is to reduce some duplicated
code, and to allow the lgh06xf tuner code to take advantage of dvb_attach().
As a side effect, the dependency of dvb-bt8xx on dvb-pll has been removed,
since the lgh06xf module itself will use dvb-pll, while remaining optional
for the dvb-bt8xx driver through the use of DVB_FE_CUSTOMISE
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a hybrid cardbus module. Besides the card support, i
modified the definition names for AGC and GPIO of the tda10046.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Satelco EasyWatch PCI DVBC cards
Signed-off-by: Thomas Hamm <thhamm@t-online.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add alternative device ID (0xb808) for AverMedia AverTV Volar dongles.
Signed-off-by: Jose Carlos Garcia Sogo <jsogo@debian.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for Nova-T Stick with USB-pid: 0x7060
Signed-off-by: Stefan Traby <stefan@hello-penguin.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the new, STK7700-based revision
of the Leadtek Winfast DTV Dongle.
Signed-off-by: Michal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the SNR calculations to use the new dvb_math log function, and add
SNR calculations for all supported modulations for both lg dt3302 and dt3303.
The QAM equations don't appear in the dt3302 datasheet, so the ones from the
dt3303 datasheet were used.
SNR returned is the actual value in dB as 8.8 fixed point.
Reporting of real signal strength isn't supported, so rather than return 0,
which confuses some software and users, a re-scaled SNR value is returned.
Code originally by Rusty Scott.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Copied routines for uc blocks and BER from the removed tda80xx.c
into tda8083.c.
Signed-off-by: Christoph Haubrich <christoph1.haubrich@arcor.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forgot to increase the device count for the STK7700P-devices
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains several fixes for the autosearch algorithm and other small ones.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains support for the DiB7000PC-driver.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First working version of the dib7000m-driver.
This commit also makes the Hauppauge NOVA-T Stick working.
Signed-off-by: Francois Kanounnikoff <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for more keys on the remote control included with the
DigitalNow tinyUSB2 DVB-T Receiver.
Signed-off-by: Luke Deller <luke@deller.id.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cxusb_lgdt3303_tuner_attach were renamed to cxusb_lgh064f_tuner_attach
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While converting everything to DVB-USB-Adapter, there was a wrong indention.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Initial commit for the driver for the DiB7000M COFDM demodulator.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The tda10086 causes an oops (divide by zero) if a zero symbol rate is used;
this prevents this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes to DISEQC on these cards inadvertently broke normal tone/voltage
signalling. This restores the necessary function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
.. fix debug printk. Why, oh why, one would want to do
(u16 & 0xff) << 8
and print it with %02x format?
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Let the MT2060 be customized like most of the other DVB PLLs/front-ends.
Also, add a missing dependency on I2C.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added config-struct-parameter to take board-specific AGC command 1 and 2 into account.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When using the remote control with the Nova-T USB there was an Oops because of
the recent DVB-USB-Adapter change.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check the return value of kmalloc() in function frontend_init(),
in file drivers/media/dvb/bt8xx/dvb-bt8xx.c.
Signed-off-by: Amit Choudhary <amit2030@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
drivers/media/dvb/dvb-usb/usb-urb.c: In function 'usb_allocate_stream_buffers':
drivers/media/dvb/dvb-usb/usb-urb.c:125: warning: format '%u' expects type 'unsigned int', but argument 4 has type 'long long unsigned int'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for DiB7000M frontend were not included on 2.6.19, since still not
completed. Removing Kconfig item.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (39 commits)
Add missing maintainer countries in CREDITS
Fix bytes <-> kilobytes typo in Kconfig for ramdisk
fix a typo in Documentation/pi-futex.txt
BUG_ON conversion for fs/xfs/
BUG_ON() conversion in fs/nfsd/
BUG_ON conversion for fs/reiserfs
BUG_ON cleanups in arch/i386
BUG_ON cleanup in drivers/net/tokenring/
BUG_ON cleanup for drivers/md/
kerneldoc-typo in led-class.c
debugfs: spelling fix
rcutorture: Fix incorrect description of default for nreaders parameter
parport: Remove space in function calls
Michal Wronski: update contact info
Spelling fix: "control" instead of "cotrol"
reboot parameter in Documentation/kernel-parameters.txt
Fix copy&waste bug in comment in scripts/kernel-doc
remove duplicate "until" from kernel/workqueue.c
ite_gpio fix tabbage
fix file specification in comments
...
Fixed trivial path conflicts due to removed files:
arch/mips/dec/boot/decstation.c, drivers/char/ite_gpio.c
Antti Palosaari