q->first_to_kick is obsolete, and can be replaced by q->first_to_check.
Both cursors start off at 0. Out of the three code paths that update
first_to_check, the qdio_inspect_queue() path is irrelevant as it
doesn't even touch first_to_kick anymore.
This leaves us with the two tasklet-driven code paths. Here any update
to first_to_check is followed by a call to qdio_kick_handler(), which
advances first_to_kick by the same amount.
So the two cursors will differ only for a tiny moment. Drivers have no
way of deterministically observing this difference, and thus it doesn't
matter which of the cursors we use for reporting an error to q->handler.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Knowing how many queues we initially allocated allows us to
1) sanity-check a subsequent qdio_establish() request, and
2) walk the queue arrays without further checks. Apply this while
cleanly splitting qdio_free_queues() into two separate helpers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Instead of having a catch-all qdio_release_memory() helper, free the
individual allocations from the respective error path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Wrap the init/exit steps for thinint into a single helper that follows
the established naming scheme.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq().
If the subsequent qdio_establish_thinint() fails, we miss to put the
DSCI again. Thus the DSCI isn't available for re-use. Given enough of
such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with
such an error internally.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
For rolling back after an error, qdio_establish() calls qdio_shutdown().
If the error occurs early enough, then the qdio_irq's state still is
QDIO_IRQ_STATE_INACTIVE and qdio_shutdown() does nothing.
But at _any_ point where qdio_establish() bails out in this way,
qdio_setup_irq() will have already replaced the IRQ handler. This then
won't be restored after an early error, and the device can end up being
returned to the device driver with qdio's IRQ handler still installed.
Slightly reorder qdio_setup_irq() so we can be 100% sure that the IRQ
handler was replaced. Then fix the bug in qdio_establish() by calling a
helper that rolls back only the IRQ handler modification.
Also use the new helper in qdio_shutdown() to keep things in sync, and
slightly clean up the locking while doing so.
This makes minor semantical changes, but holding setup_mutex gives us
sufficient leeway to eg. pull qdio_shutdown_thinint() outside of the
ccwdev lock's scope.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Polling drivers in a configuration with 1 Input Queue currently keep
their DSCI armed all the way through the poll cycle, until
qdio_start_irq() clears it.
_Any_ intermittent QDIO interrupt delivered to tiqdio_thinint_handler()
will thus cause
1) the 'adapter_int' statistic to be incremented,
2) a call to tiqdio_call_inq_handlers() for this device, and then
3) the 'int_discarded' statistics to be incremented.
This causes overhead & complexity in the IRQ path, along with ambiguity
in the statistics.
On the other hand the device should be in IRQ avoidance mode during a
poll cycle, so there won't be a lot of DSCI ping-pong that this
micro-optimization could prevent.
So align the DSCI handling with what we already do for devices with
multiple Input Queues: clear it right away while processing the IRQ.
For the non-polling path this means that we no longer need to handle
the 1-queue case separately.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
Set up qdio_irq->cdev right when the qdio_irq struct is allocated, so
that all subsequent code can rely on this pointer.
Then convert two helper functions to not pass a cdev parameter around.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need for error handling, the debugfs core is smart enough to
deal with IS_ERR() internally.
This will also keep us from creating the debugfs files if the device
directory doesn't exist. Currently (because irq_ptr->debugfs_dev gets set
to NULL on error) the files would be placed into the debugfs root - without
any association to their parent device.
On teardown, use the debugfs_remove_recursive() helper to avoid keeping
track of each created file/directory.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove all usage of cdev->private->qdio_data that's buried deep in
internal code. This should only be used by the exported driver API,
which can then pass around a proper qdio_irq pointer.
Also trivially merge some initializations with their definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Current code uses a 'polling' flag to keep track of whether an Input
Queue has any ACKed SBALs. QEBSM devices might have multiple ACKed
SBALs, and those are tracked separately with 'ack_count'.
By also setting ack_count for non-QEBSM devices (to a fixed value of 1),
we can use 'ack_count != 0' as replacement for the polling flag.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
This allows IQD drivers to send out multiple SBALs with a single SIGA
instruction.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an interrupt, tiqdio_thinint_handler() walks a list of all objects
that might require attention, and checks their DSCI. This list is
awkwardly built from Input Queues, even though the IRQs are per-device
and the queue is then only used to dereference its qdio_irq parent.
To simplify the logic, change the code so that tiq_list contains
qdio_irq entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
qperf_inc() takes a queue as input, but actually updates the statistics
in its qdio_irq parent.
In some contexts we already have access to the qdio_irq struct, and can
avoid the additional dereference.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
qdio.h recently gained a new helper macro that handles wrap-around on a
QDIO queue, use it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
If a driver wants to use the new Output Queue poll code, then the qdio
layer must disable its internal Queue scanning. Let the driver select
this mode by passing a special scan_threshold of 0.
As the scan_threshold is the same for all Output Queues, also move it
into the main qdio_irq struct. This allows for fast opt-out checking, a
driver is expected to operate either _all_ or none of its Output Queues
in polling mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cursor is used for debugging only. But since
commit "s390/qdio: pass up count of ready-to-process SBALs" it effectively
duplicates the first_to_check cursor, diverging for just a short moment
when get_*_buffer_frontier() updates q->first_to_check.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pci_out_supported() currently takes a single queue as parameter, even
though Output IRQ support is a per-device feature. Adjust the parameter,
so that the macro can also be used in code paths with no access to a queue
struct. This allows us to remove the remaining open-coded checks for
QIB_AC_OUTBOUND_PCI_SUPPORTED.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
[sebott: fixed compile error due to invalid struct member]
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e58 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I observed that there are for_each macros that do an extra memory access
beyond the defined area.
Normally this does not cause problems.
But, this can cause exceptions. For example: if the area is allocated at
the end of a page and the next page is not accessible.
For correctness, I suggest changing the arguments of the 'for loop' like
others 'for_each' do in the kernel.
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the code to issue the set adapter device controls command to
chsc.c and make it accessible for the qdio code via the wrapper
chsc_sadc.
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup the function qdio_setup_get_ssqd. Fix some possible
memleaks and an unchecked allocation and create a wrapper
for SSQD in chsc.c .
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
A kernel panic may occur during sending or receiving network packets
on a machine without adapter interrupts since commit d36deae.
The bug is triggered by writing to the shared indicator address which
is set to 0 if the machine doesn't have adapter interrupts.
Make the reading and setting of the shared indicator dependent on the
adapter interrupt feature and while at it move the code to the
file containing the adapter interrupt related code.
Thanks to Jan Jaeger for tracking this down.
Reported-by: Jan Jaeger <jan.jaeger@westnet.com.au>
Tested-by: Jan Jaeger <jan.jaeger@westnet.com.au>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The multicast poll check for the outbound queue is redundant since
3d6c76f "[S390] qdio: outbound tasklet scan threshold". Remove the check.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a timestamp per queue and update the timestamp when the queue is
scanned. Add the queue timestamps and the timestamp of the last
adapter interrupt to the debugfs output. The timestamps are useful
for debugging stall conditions.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces support for asynchronous delivery of storage blocks for
Hipersockets. Upper layers may exploit this functionality to reuse SBALs for
which the delivery status is still pending.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIGA-W may return with the busy bit set which means the device was
blocked. The busy loop which retries the SIGA-W for 100us may not be
long enough when running under a heavily loaded hypervisor.
Extend the retry mechanism by adding a longer second stage which retries
the SIGA-W for up to 10s. In difference to the first retry loop the second
stage is using mdelay to stop the cpu between the retries and thereby
avoid additional preassure in on the hypervisor.
If the second stage retry is successfull a device reset is avoided.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Simplify the SIGA sync code and add unlikely annotations. In polling mode
SBALs may be accessed without interrupt, so call SIGA sync before every scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
HiperSocket devices only use one SBAL per qdio call without the enhanced SIGA
feature. Since that feature is currently not used remove it from the qdio code
so the compiler can generate better code for the HiperSocket outbound path.
While at it mark the SIGA error conditions as unlikely.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If QIOASSIST is enabled for a qdio device the SIGA instruction requires
a modified function code. This function code modifier was missing for
SIGA-R and SIGA-S which can lead to a kernel panic caused by an
operand exception.
Cc: stable@kernel.org
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a counter for outbound queue full events to the qdio statistics.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a scan treshold for the qdio outbound queues. By setting the
threshold the driver can tell qdio after how much used SBALs qdio
should schedule the outbound tasklet that scans the queue for finished
SBALs. The threshold is specific by the drivers because a
Hipersockets device is much faster in utilizing outbound buffers than a
ZFCP or OSA device.
The default values after how many used SBALs the tasklet should run are:
OSA: > 31 SBALs
Hipersockets: > 7 SBALs
zfcp: > 55 SBALs
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the shared indicator is used the following race leads to
an inbound stall:
Device CPU0 CPU1
========================================================
non-shared DSCI =>1
ALSI => 1
Thin INT
ALSI => 0
non-shared DSCI
tasklets scheduled
shared DSCI => 1
ALSI => 1
shared DSCI => 0
ALSI ? -> set
Thin INT
ALSI => 0
ALSI was set,
shared DSCI => 1
After that no more interrupts occur because the DSCI is still set.
Fix that race by only resetting the shared DSCI if it was actually
set so the tasklets for all shared devices are scheduled and will
run after the interrupt.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend the qdio API to allow polling in the upper-layer driver. This
is needed by qeth to use NAPI.
To use the new interface the upper-layer driver must specify the
queue_start_poll(). This callback is used to signal the upper-layer
driver that is has initiative and must process the inbound queue by
calling qdio_get_next_buffers(). If the upper-layer driver wants to
stop polling it calls qdio_start_irq().
Since adapter interrupts are not completely stoppable qdio implements
a software bit QDIO_QUEUE_IRQS_DISABLED to safely disable interrupts for an
input queue.
The old interface is preserved and will be used as is by zfcp.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't convert timestamps to microseconds, use timestamps returned by
get_clock() directly.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove memset hack that relied on the layout of struct qdio_q
to avoid deletion of the slib pointer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove a memset hack that relied on the internal layout of the
qdio_irq struct and move the per device statistics data into an own
cache line to avoid cache line bashing between the inbound and the
outbound queue tasklets. Also reduce the number of allocated queues
from 32 to 4 which is the current maximum. That saves a cache line
in struct qdio_irq.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add counters for the number of processed SBALs. The numbers summarize
how many SBALs were processed at each queue scan and indicate the
utilization of the queue. Furthermore the number of unsuccessfull
queue scans, SBAL errors and the total number of processed
SBALs are accounted.
Also regroup struct qdio_q to move read-mostly and write-mostly data
into different cachelines.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Revamp the qdio performance statistics and move them from procfs to
debugfs using the seq_file interface. Since the statistics are not
intended for the general user the removal of /proc/qdio_perf should
not surprise anyone.
The per device statistics are disabled by default, writing 1 to
/<debugfs mountpoint>/qdio/<device bus ID>/statistics enables the
statistics for the given device.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The number of qdio debugfs entries was limited. Remove this limit
and group the queue files in a per device directory.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the adapter interrupt tasklet function to the qdio main code
since all the functions used by the tasklet are located there.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The inbound and outbound handlers are nearly identical if the outbound
handler uses first_to_check as end index instead of last_move. Since both
values are identical at that point the handlers can be merged.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Julian Wiedmann