Make sure the stack-protector segment registers are properly set up
before calling any functions which may have stack-protection compiled
into them.
[ Impact: prevent Xen early-boot crash when stack-protector is enabled ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
stts() is implemented in terms of read_cr0/write_cr0 to update the
state of the TS bit. This happens during context switch, and so
is fairly performance critical. Rather than falling back to
a trap-and-emulate native read_cr0, implement our own by caching
the last-written value from write_cr0 (the TS bit is the only one
we really care about).
Impact: optimise Xen context switches
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Ignore known IST-using traps. Aside from the debugger traps, they're
low-level faults which Xen will handle for us, so the kernel needn't
worry about them. Keep warning in case unknown trap starts using IST.
Impact: suppress spurious warnings
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Native x86-64 uses the IST mechanism to run int3 and debug traps on
an alternative stack. Xen does not do this, and so the frames were
being misinterpreted by the ptrace code. This change special-cases
these two exceptions by using Xen variants which run on the normal
kernel stack properly.
Impact: avoid crash or bad data when IST trap is invoked under Xen
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Some 64-bit machines don't support the NX flag in ptes.
Check for NX before constructing the kernel pagetables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Xen leaves XSAVE set in cpuid, but doesn't allow cr4.OSXSAVE
to be set. This confuses the kernel and it ends up crashing on
an xsetbv instruction.
At boot time, try to set cr4.OSXSAVE, and mask XSAVE out of
cpuid it we can't. This will produce a spurious error from Xen,
but allows us to support XSAVE if/when Xen does.
This also factors out the cpuid mask decisions to boot time.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Remove use of multicall machinery which is unused (gdt loading
is never performance critical). This removes the implicit use
of percpu variables, which simplifies understanding how
the percpu code's use of load_gdt interacts with this code.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Some 64-bit machines don't support the NX flag in ptes.
Check for NX before constructing the kernel pagetables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Xen leaves XSAVE set in cpuid, but doesn't allow cr4.OSXSAVE
to be set. This confuses the kernel and it ends up crashing on
an xsetbv instruction.
At boot time, try to set cr4.OSXSAVE, and mask XSAVE out of
cpuid it we can't. This will produce a spurious error from Xen,
but allows us to support XSAVE if/when Xen does.
This also factors out the cpuid mask decisions to boot time.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Remove use of multicall machinery which is unused (gdt loading
is never performance critical). This removes the implicit use
of percpu variables, which simplifies understanding how
the percpu code's use of load_gdt interacts with this code.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: fix lazy context switch API
Pass the previous and next tasks into the context switch start
end calls, so that the called functions can properly access the
task state (esp in end_context_switch, in which the next task
is not yet completely current).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Impact: allow preemption during lazy mmu updates
If we're in lazy mmu mode when context switching, leave
lazy mmu mode, but remember the task's state in
TIF_LAZY_MMU_UPDATES. When we resume the task, check this
flag and re-enter lazy mmu mode if its set.
This sets things up for allowing lazy mmu mode while preemptible,
though that won't actually be active until the next change.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
The virtually mapped percpu space causes us two problems:
- for hypercalls which take an mfn, we need to do a full pagetable
walk to convert the percpu va into an mfn, and
- when a hypercall requires a page to be mapped RO via all its aliases,
we need to make sure its RO in both the percpu mapping and in the
linear mapping
This primarily affects the gdt and the vcpu info structure.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids a lockdep warning from:
if (DEBUG_LOCKS_WARN_ON(unlikely(!early_boot_irqs_enabled)))
return;
in trace_hardirqs_on_caller();
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
make it simpler, don't need have one extra struct.
v2: fix the sgi_uv build
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: pt_regs changed, lazy gs handling made optional, add slight
overhead to SAVE_ALL, simplifies error_code path a bit
On x86_32, %gs hasn't been used by kernel and handled lazily. pt_regs
doesn't have place for it and gs is saved/loaded only when necessary.
In preparation for stack protector support, this patch makes lazy %gs
handling optional by doing the followings.
* Add CONFIG_X86_32_LAZY_GS and place for gs in pt_regs.
* Save and restore %gs along with other registers in entry_32.S unless
LAZY_GS. Note that this unfortunately adds "pushl $0" on SAVE_ALL
even when LAZY_GS. However, it adds no overhead to common exit path
and simplifies entry path with error code.
* Define different user_gs accessors depending on LAZY_GS and add
lazy_save_gs() and lazy_load_gs() which are noop if !LAZY_GS. The
lazy_*_gs() ops are used to save, load and clear %gs lazily.
* Define ELF_CORE_COPY_KERNEL_REGS() which always read %gs directly.
xen and lguest changes need to be verified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enable the use of the direct vcpu-access operations on 64-bit.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We need to access percpu data fairly early, so set up the percpu
registers as soon as possible. We only need to load the appropriate
segment register. We already have a GDT, but its hard to change it
early because we need to manipulate the pagetable to do so, and that
hasn't been set up yet.
Also, set the kernel stack when bringing up secondary CPUs. If we
don't they all end up sharing the same stack...
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: fix xen booting
We need to access percpu data fairly early, so set up the percpu
registers as soon as possible. We only need to load the appropriate
segment register. We already have a GDT, but its hard to change it
early because we need to manipulate the pagetable to do so, and that
hasn't been set up yet.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: Optimization
One of the problems with inserting a pile of C calls where previously
there were none is that the register pressure is greatly increased.
The C calling convention says that the caller must expect a certain
set of registers may be trashed by the callee, and that the callee can
use those registers without restriction. This includes the function
argument registers, and several others.
This patch seeks to alleviate this pressure by introducing wrapper
thunks that will do the register saving/restoring, so that the
callsite doesn't need to worry about it, but the callee function can
be conventional compiler-generated code. In many cases (particularly
performance-sensitive cases) the callee will be in assembler anyway,
and need not use the compiler's calling convention.
Standard calling convention is:
arguments return scratch
x86-32 eax edx ecx eax ?
x86-64 rdi rsi rdx rcx rax r8 r9 r10 r11
The thunk preserves all argument and scratch registers. The return
register is not preserved, and is available as a scratch register for
unwrapped callee code (and of course the return value).
Wrapped function pointers are themselves wrapped in a struct
paravirt_callee_save structure, in order to get some warning from the
compiler when functions with mismatched calling conventions are used.
The most common paravirt ops, both statically and dynamically, are
interrupt enable/disable/save/restore, so handle them first. This is
particularly easy since their calls are handled specially anyway.
XXX Deal with VMI. What's their calling convention?
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Cleanup
Move remaining mmu-related stuff into mmu.c.
A general cleanup, and lay the groundwork for later patches.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
pte_flags() was introduced as a new pvop in order to extract just the
flags portion of a pte, which is a potentially cheaper operation than
extracting the page number as well. It turns out this operation is
not needed, because simply using a mask to extract the flags from a
pte is sufficient for all current users.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Copy the code to cpu_init() to satisfy the requirement that the cpu
be reinitialized. Remove all other calls, since the segments are
already initialized in head_64.S.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It is an optimization and a cleanup, and adds the following new
generic percpu methods:
percpu_read()
percpu_write()
percpu_add()
percpu_sub()
percpu_and()
percpu_or()
percpu_xor()
and implements support for them on x86. (other architectures will fall
back to a default implementation)
The advantage is that for example to read a local percpu variable,
instead of this sequence:
return __get_cpu_var(var);
ffffffff8102ca2b: 48 8b 14 fd 80 09 74 mov -0x7e8bf680(,%rdi,8),%rdx
ffffffff8102ca32: 81
ffffffff8102ca33: 48 c7 c0 d8 59 00 00 mov $0x59d8,%rax
ffffffff8102ca3a: 48 8b 04 10 mov (%rax,%rdx,1),%rax
We can get a single instruction by using the optimized variants:
return percpu_read(var);
ffffffff8102ca3f: 65 48 8b 05 91 8f fd mov %gs:0x7efd8f91(%rip),%rax
I also cleaned up the x86-specific APIs and made the x86 code use
these new generic percpu primitives.
tj: * fixed generic percpu_sub() definition as Roel Kluin pointed out
* added percpu_and() for completeness's sake
* made generic percpu ops atomic against preemption
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Tejun Heo <tj@kernel.org>
Do the following cleanups:
* kill x86_64_init_pda() which now is equivalent to pda_init()
* use per_cpu_offset() instead of cpu_pda() when initializing
initial_gs
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce stack usage, use new cpumask API.
This is made a little more tricky by uv_flush_tlb_others which
actually alters its argument, for an IPI to be sent to the remaining
cpus in the mask.
I solve this by allocating a cpumask_var_t for this case and falling back
to IPI should this fail.
To eliminate temporaries in the caller, all flush_tlb_others implementations
now do the this-cpu-elimination step themselves.
Note also the curious "cpus_or(f->flush_cpumask, cpumask, f->flush_cpumask)"
which has been there since pre-git and yet f->flush_cpumask is always zero
at this point.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: cleanup
hypervisor.h had accumulated a lot of crud, including lots of spurious
#includes. Clean it all up, and go around fixing up everything else
accordingly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Xen requires that all mappings of pagetable pages are read-only, so
that they can't be updated illegally. As a result, if a page is being
turned into a pagetable page, we need to make sure all its mappings
are RO.
If the page had been used for ioremap or vmalloc, it may still have
left over mappings as a result of not having been lazily unmapped.
This change makes sure we explicitly mop them all up before pinning
the page.
Unlike aliases created by kmap, the there can be vmalloc aliases even
for non-high pages, so we must do the flush unconditionally.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Linux Memory Management List <linux-mm@kvack.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and
provide a fast, scalable percpu frontend for small vmaps (requires a
slightly different API, though).
The biggest problem with vmap is actually vunmap. Presently this requires
a global kernel TLB flush, which on most architectures is a broadcast IPI
to all CPUs to flush the cache. This is all done under a global lock. As
the number of CPUs increases, so will the number of vunmaps a scaled
workload will want to perform, and so will the cost of a global TLB flush.
This gives terrible quadratic scalability characteristics.
Another problem is that the entire vmap subsystem works under a single
lock. It is a rwlock, but it is actually taken for write in all the fast
paths, and the read locking would likely never be run concurrently anyway,
so it's just pointless.
This is a rewrite of vmap subsystem to solve those problems. The existing
vmalloc API is implemented on top of the rewritten subsystem.
The TLB flushing problem is solved by using lazy TLB unmapping. vmap
addresses do not have to be flushed immediately when they are vunmapped,
because the kernel will not reuse them again (would be a use-after-free)
until they are reallocated. So the addresses aren't allocated again until
a subsequent TLB flush. A single TLB flush then can flush multiple
vunmaps from each CPU.
XEN and PAT and such do not like deferred TLB flushing because they can't
always handle multiple aliasing virtual addresses to a physical address.
They now call vm_unmap_aliases() in order to flush any deferred mappings.
That call is very expensive (well, actually not a lot more expensive than
a single vunmap under the old scheme), however it should be OK if not
called too often.
The virtual memory extent information is stored in an rbtree rather than a
linked list to improve the algorithmic scalability.
There is a per-CPU allocator for small vmaps, which amortizes or avoids
global locking.
To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces
must be used in place of vmap and vunmap. Vmalloc does not use these
interfaces at the moment, so it will not be quite so scalable (although it
will use lazy TLB flushing).
As a quick test of performance, I ran a test that loops in the kernel,
linearly mapping then touching then unmapping 4 pages. Different numbers
of tests were run in parallel on an 4 core, 2 socket opteron. Results are
in nanoseconds per map+touch+unmap.
threads vanilla vmap rewrite
1 14700 2900
2 33600 3000
4 49500 2800
8 70631 2900
So with a 8 cores, the rewritten version is already 25x faster.
In a slightly more realistic test (although with an older and less
scalable version of the patch), I ripped the not-very-good vunmap batching
code out of XFS, and implemented the large buffer mapping with vm_map_ram
and vm_unmap_ram... along with a couple of other tricks, I was able to
speed up a large directory workload by 20x on a 64 CPU system. I believe
vmap/vunmap is actually sped up a lot more than 20x on such a system, but
I'm running into other locks now. vmap is pretty well blown off the
profiles.
Before:
1352059 total 0.1401
798784 _write_lock 8320.6667 <- vmlist_lock
529313 default_idle 1181.5022
15242 smp_call_function 15.8771 <- vmap tlb flushing
2472 __get_vm_area_node 1.9312 <- vmap
1762 remove_vm_area 4.5885 <- vunmap
316 map_vm_area 0.2297 <- vmap
312 kfree 0.1950
300 _spin_lock 3.1250
252 sn_send_IPI_phys 0.4375 <- tlb flushing
238 vmap 0.8264 <- vmap
216 find_lock_page 0.5192
196 find_next_bit 0.3603
136 sn2_send_IPI 0.2024
130 pio_phys_write_mmr 2.0312
118 unmap_kernel_range 0.1229
After:
78406 total 0.0081
40053 default_idle 89.4040
33576 ia64_spinlock_contention 349.7500
1650 _spin_lock 17.1875
319 __reg_op 0.5538
281 _atomic_dec_and_lock 1.0977
153 mutex_unlock 1.5938
123 iget_locked 0.1671
117 xfs_dir_lookup 0.1662
117 dput 0.1406
114 xfs_iget_core 0.0268
92 xfs_da_hashname 0.1917
75 d_alloc 0.0670
68 vmap_page_range 0.0462 <- vmap
58 kmem_cache_alloc 0.0604
57 memset 0.0540
52 rb_next 0.1625
50 __copy_user 0.0208
49 bitmap_find_free_region 0.2188 <- vmap
46 ia64_sn_udelay 0.1106
45 find_inode_fast 0.1406
42 memcmp 0.2188
42 finish_task_switch 0.1094
42 __d_lookup 0.0410
40 radix_tree_lookup_slot 0.1250
37 _spin_unlock_irqrestore 0.3854
36 xfs_bmapi 0.0050
36 kmem_cache_free 0.0256
35 xfs_vn_getattr 0.0322
34 radix_tree_lookup 0.1062
33 __link_path_walk 0.0035
31 xfs_da_do_buf 0.0091
30 _xfs_buf_find 0.0204
28 find_get_page 0.0875
27 xfs_iread 0.0241
27 __strncpy_from_user 0.2812
26 _xfs_buf_initialize 0.0406
24 _xfs_buf_lookup_pages 0.0179
24 vunmap_page_range 0.0250 <- vunmap
23 find_lock_page 0.0799
22 vm_map_ram 0.0087 <- vmap
20 kfree 0.0125
19 put_page 0.0330
18 __kmalloc 0.0176
17 xfs_da_node_lookup_int 0.0086
17 _read_lock 0.0885
17 page_waitqueue 0.0664
vmap has gone from being the top 5 on the profiles and flushing the crap
out of all TLBs, to using less than 1% of kernel time.
[akpm@linux-foundation.org: cleanups, section fix]
[akpm@linux-foundation.org: fix build on alpha]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When reserving space for the hypervisor the Xen paravirt backend adds
an extra two pages (this was carried forward from the 2.6.18-xen tree
which had them "for safety"). Depending on various CONFIG options this
can cause the boot time fixmaps to span multiple PMDs which is not
supported and triggers a WARN in early_ioremap_init().
This was exposed by 2216d199b1 which
moved the dmi table parsing earlier.
x86: fix CONFIG_X86_RESERVE_LOW_64K=y
The bad_bios_dmi_table() quirk never triggered because we do DMI setup
too late. Move it a bit earlier.
There is no real reason to reserve these two extra pages and the
fixmap already incorporates FIX_HOLE which serves the same
purpose. None of the other callers of reserve_top_address do this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a couple of Xen features which rely on directly accessing
per-cpu data via a segment register, which is not yet available on
x86-64. In the meantime, just disable direct access to the vcpu info
structure; this leaves some of the code as dead, but it will come to
life in time, and the warnings are suppressed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We only pin PTE pages when using split PTE locks, so don't do the
pin/unpin when attaching/detaching pte pages to a pinned pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using native_pte_val triggers the BUG_ON() in the paravirt_ops
version of pte_flags().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the pfn args from 'u32' to 'unsigned long'
on alloc_p*() functions on paravirt_ops, and the corresponding
implementations for Xen and VMI. The prototypes for CONFIG_PARAVIRT=n
are already using unsigned long, so paravirt.h now matches the prototypes
on asm-x86/pgalloc.h.
It shouldn't result in any changes on generated code on 32-bit, with
or without CONFIG_PARAVIRT. On both cases, 'codiff -f' didn't show any
change after applying this patch.
On 64-bit, there are (expected) binary changes only when CONFIG_PARAVIRT
is enabled, as the patch is really supposed to change the size of the
pfn args.
[ v2: KVM_GUEST: use the right parameter type on kvm_release_pt() ]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are four operating modes Xen code may find itself running in:
- native
- hvm domain
- pv dom0
- pv domU
Clean up predicates for testing for these states to make them more consistent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently paravirt_ops alloc_p*() uses u32 for the pfn args. We should
change that later, but while the pfn parameter is still u32, we need to
cast the PFN_PHYS() argument at xen_alloc_ptpage() to unsigned long,
otherwise it will lose bits on the shift.
I think PFN_PHYS() should behave better when fed with smaller integers,
but a cast to unsigned long won't be enough for all cases on 32-bit PAE,
and a cast to u64 would be overkill for most users of PFN_PHYS().
We could have two different flavors of PFN_PHYS: one for low pages
only (unsigned long) and another that works for any page (u64)),
but while we don't have it, we will need the cast to unsigned long on
xen_alloc_ptpage().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a proper comment for set_aliased_prot() and fix an
unsigned long/void * warning.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For some reason I managed to miss a bunch of irq-related functions
which also need to be compiled without -pg when using ftrace. This
patch moves them into their own file, and starts a cleanup process
I've been meaning to do anyway.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: "Alex Nixon (Intern)" <Alex.Nixon@eu.citrix.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In general, Xen doesn't support wrmsr from an unprivileged domain; it
just ends up ignoring the instruction and printing a message on the
console.
Given that there are sets of MSRs we know the kernel will try to write
to, but we don't care, just eat them in xen_write_msr to cut down on
console noise.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the ldt gets to more than 1 page in size, the kernel uses vmalloc
to allocate it. This means that:
- when making the ldt RO, we must update the pages in both the vmalloc
mapping and the linear mapping to make sure there are no RW aliases.
- we need to use arbitrary_virt_to_machine to compute the machine addr
for each update
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using native_pte_val triggers the BUG_ON() in the paravirt_ops
version of pte_flags().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LTP testing showed that Xen does not properly implement
sys_modify_ldt(). This patch does the final little bits needed to
make the ldt work properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rusty, in his peevish way, complained that macros defining constants
should have a name which somewhat accurately reflects the actual
purpose of the constant.
Aside from the fact that PTE_MASK gives no clue as to what's actually
being masked, and is misleadingly similar to the functionally entirely
different PMD_MASK, PUD_MASK and PGD_MASK, I don't really see what the
problem is.
But if this patch silences the incessent noise, then it will have
achieved its goal (TODO: write test-case).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/xen/enlighten.c:615: error: variable ‘xen_basic_apic_ops’ has initializer but incomplete type
arch/x86/xen/enlighten.c:616: error: unknown field ‘read’ specified in initializer
[...]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Various versions of the hypervisor have differences in what ABIs and
features they support. Print some details into the boot log to help
with remote debugging.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use alternatives to select the workaround for the 11AP Pentium erratum
for the affected steppings on the fly rather than build time. Remove the
X86_GOOD_APIC configuration option and replace all the calls to
apic_write_around() with plain apic_write(), protecting accesses to the
ESR as appropriate due to the 3AP Pentium erratum. Remove
apic_read_around() and all its invocations altogether as not needed.
Remove apic_write_atomic() and all its implementing backends. The use of
ASM_OUTPUT2() is not strictly needed for input constraints, but I have
used it for readability's sake.
I had the feeling no one else was brave enough to do it, so I went ahead
and here it is. Verified by checking the generated assembly and tested
with both a 32-bit and a 64-bit configuration, also with the 11AP
"feature" forced on and verified with gdb on /proc/kcore to work as
expected (as an 11AP machines are quite hard to get hands on these days).
Some script complained about the use of "volatile", but apic_write() needs
it for the same reason and is effectively a replacement for writel(), so I
have disregarded it.
I am not sure what the policy wrt defconfig files is, they are generated
and there is risk of a conflict resulting from an unrelated change, so I
have left changes to them out. The option will get removed from them at
the next run.
Some testing with machines other than mine will be needed to avoid some
stupid mistake, but despite its volume, the change is not really that
intrusive, so I am fairly confident that because it works for me, it will
everywhere.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/xen/enlighten.c: In function 'xen_set_fixmap':
arch/x86/xen/enlighten.c:1127: error: 'FIX_KMAP_BEGIN' undeclared (first use in this function)
arch/x86/xen/enlighten.c:1127: error: (Each undeclared identifier is reported only once
arch/x86/xen/enlighten.c:1127: error: for each function it appears in.)
arch/x86/xen/enlighten.c:1127: error: 'FIX_KMAP_END' undeclared (first use in this function)
make[1]: *** [arch/x86/xen/enlighten.o] Error 1
make: *** [arch/x86/xen/enlighten.o] Error 2
FIX_KMAP_BEGIN is only available on HIGHMEM.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit uses MSRs for important things like the base for fs and
gs-prefixed addresses. It's more efficient to use a hypercall to
update these, rather than go via the trap and emulate path.
Other MSR writes are just passed through; in an unprivileged domain
they do nothing, but it might be useful later.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit userspace expects the vdso to be mapped at a specific fixed
address, which happens to be in the middle of the kernel address
space. Because we have split user and kernel pagetables, we need to
make special arrangements for the vsyscall mapping to appear in the
kernel part of the user pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We set up entrypoints for syscall and sysenter. sysenter is only used
for 32-bit compat processes, whereas syscall can be used in by both 32
and 64-bit processes.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Because the x86_64 architecture does not enforce segment limits, Xen
cannot protect itself with them as it does in 32-bit mode. Therefore,
to protect itself, it runs the guest kernel in ring 3. Since it also
runs the guest userspace in ring3, the guest kernel must maintain a
second pagetable for its userspace, which does not map kernel space.
Naturally, the guest kernel pagetables map both kernel and userspace.
The userspace pagetable is attached to the corresponding kernel
pagetable via the pgd's page->private field. It is allocated and
freed at the same time as the kernel pgd via the
paravirt_pgd_alloc/free hooks.
Fortunately, the user pagetable is almost entirely shared with the
kernel pagetable; the only difference is the pgd page itself. set_pgd
will populate all entries in the kernel pagetable, and also set the
corresponding user pgd entry if the address is less than
STACK_TOP_MAX.
The user pagetable must be pinned and unpinned with the kernel one,
but because the pagetables are aliased, pgd_walk() only needs to be
called on the kernel pagetable. The user pgd page is then
pinned/unpinned along with the kernel pgd page.
xen_write_cr3 must write both the kernel and user cr3s.
The init_mm.pgd pagetable never has a user pagetable allocated for it,
because it can never be used while running usermode.
One awkward area is that early in boot the page structures are not
available. No user pagetable can exist at that point, but it
complicates the logic to avoid looking at the page structure.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to do this, otherwise we can get a GPF on hypercall return
after TLS descriptor is cleared but %fs is still pointing to it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Point the boot params cmd_line_ptr to the domain-builder-provided
command line.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The x86_64 interrupt subsystem is oriented towards vectors, as opposed
to a flat irq space as it is in x86-32. This patch adds a simple
identity irq->vector mapping so that we can continue to feed irqs into
do_IRQ() and get a good result.
Ideally x86_32 will unify with the 64-bit code and use vectors too.
At that point we can move to mapping event channels to vectors, which
will allow us to economise on irqs (so per-cpu event channels can
share irqs, rather than having to allocte one per cpu, for example).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
swapgs is a no-op under Xen, because the hypervisor makes sure the
right version of %gs is current when switching between user and kernel
modes. This means that the swapgs "implementation" can be inlined and
used when the stack is unsafe (usermode). Unfortunately, it means
that disabling patching will result in a non-booting kernel...
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Xen pushes two extra words containing the values of rcx and r11. This
pvop hook copies the words back into their appropriate registers, and
cleans them off the stack. This leaves the stack in native form, so
the normal handler can run unchanged.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to wait until the page structure is available to use the
proper pagetable page alloc/release operations, since they use struct
page to determine if a pagetable is pinned.
This happened to work in 32bit because nobody allocated new pagetable
pages in the interim between xen_pagetable_setup_done and
xen_post_allocator_init, but the 64-bit kenrel needs to allocate more
pagetable levels.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rearrange the pagetable initialization to share code with the 64-bit
kernel. Rather than deferring anything to pagetable_setup_start, just
set up an initial pagetable in swapper_pg_dir early at startup, and
create an additional 8MB of physical memory mappings. This matches
the native head_32.S mappings to a large degree, and allows the rest
of the pagetable setup to continue without much Xen vs. native
difference.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early in boot, map a chunk of extra physical memory for use later on.
We need a pool of mapped pages to allocate further pages to construct
pagetables mapping all physical memory.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It also doesn't need the 32-bit hack version of set_pte for initial
pagetable construction, so just make it use the real thing.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Set up the initial pagetables to map the kernel mapping into the
physical mapping space. This makes __va() usable, since it requires
physical mappings.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As a stopgap until Mike Travis's x86-64 gs-based percpu patches are
ready, provide workaround functions for x86_read/write_percpu for
Xen's use.
Specifically, this means that we can't really make use of vcpu
placement, because we can't use a single gs-based memory access to get
to vcpu fields. So disable all that for now.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move all the smp_ops setup into smp.c, allowing a lot of things to
become static.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need extra pv_mmu_ops for 64-bit, to deal with the extra level of
pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need set_pte to work from a relatively early point, so enable it
from the start.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call paravirt_pagetable_setup_{start,done}
These paravirt_ops functions were not being called on x86_64.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix for pv - clean up the namespace there too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Define the Xen specific basic apic ops, in additon to paravirt apic ops,
with some misc warning fixes.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the paravirtualized calculate_cpu_khz to calibrate_tsc.
In all cases, we actually calibrate_tsc and use that as the cpu_khz value.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit Xen pushes a couple of extra words onto an exception frame.
Add a hook to deal with them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't conflate sysret and sysexit; they're different instructions with
different semantics, and may be in use at the same time (at least
within the same kernel, depending on whether its an Intel or AMD
system).
sysexit - just return to userspace, does no register restoration of
any kind; must explicitly atomically enable interrupts.
sysret - reloads flags from r11, so no need to explicitly enable
interrupts on 64-bit, responsible for restoring usermode %gs
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citirx.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add hooks which are called at pgd_alloc/free time. The pgd_alloc hook
may return an error code, which if non-zero, causes the pgd allocation
to be failed. The hooks may be used to allocate/free auxillary
per-pgd information.
also fix:
> * Ingo Molnar <mingo@elte.hu> wrote:
>
> include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
> arch/x86/kernel/entry_64.S: In file included from
> arch/x86/kernel/traps_64.c:51:include/asm/pgalloc.h: In function ‘paravirt_pgd_free':
> include/asm/pgalloc.h:14: error: parameter name omitted
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This converts x86, x86-64, and xen to use the new helpers for
smp_call_function() and friends, and adds support for
smp_call_function_single().
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Xen has a pte update function which will update a pte while preserving
its accessed and dirty bits. This means that ptep_modify_prot_start() can be
implemented as a simple read of the pte value. The hardware may
update the pte in the meantime, but ptep_modify_prot_commit() updates it while
preserving any changes that may have happened in the meantime.
The updates in ptep_modify_prot_commit() are batched if we're currently in lazy
mmu mode.
The mmu_update hypercall can take a batch of updates to perform, but
this code doesn't make particular use of that feature, in favour of
using generic multicall batching to get them all into the hypervisor.
The net effect of this is that each mprotect pte update turns from two
expensive trap-and-emulate faults into they hypervisor into a single
hypercall whose cost is amortized in a batched multicall.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds paravirt-ops hooks in pv_mmu_ops for ptep_modify_prot_start and
ptep_modify_prot_commit. This allows the hypervisor-specific backends to
implement these in some more efficient way.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used. xen-unstable has now officially dropped
non-PAE support. Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Stable: this isn't a bugfix in itself, but it's a pre-requiste
for "xen: don't drop NX bit" ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: the arch/x86 maintainers <x86@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Stable: this isn't a bugfix in itself, but it's a pre-requiste
for "xen: don't drop NX bit" ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: the arch/x86 maintainers <x86@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If we're using vcpu_info mapping, then make sure its restored on all
processors before relasing them from stop_machine.
The only complication is that if this fails, we can't continue because
we've already made assumptions that the mapping is available (baked in
calls to the _direct versions of the functions, for example).
Fortunately this can only happen with a 32-bit hypervisor, which may
possibly run out of mapping space. On a 64-bit hypervisor, this is a
non-issue.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When operating on an unpinned pagetable (ie, one under construction or
destruction), it isn't necessary to use a hypercall to update a
pud/pmd entry. Jan Beulich observed that a similar optimisation
avoided many thousands of hypercalls while doing a kernel build.
One tricky part is that early in the kernel boot there's no page
structure, so we can't check to see if the page is pinned. In that
case, we just always use the hypercall.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce init_pg_table_start, so xen PV could specify the value.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements Xen save/restore and migration.
Saving is triggered via xenbus, which is polled in
drivers/xen/manage.c. When a suspend request comes in, the kernel
prepares itself for saving by:
1 - Freeze all processes. This is primarily to prevent any
partially-completed pagetable updates from confusing the suspend
process. If CONFIG_PREEMPT isn't defined, then this isn't necessary.
2 - Suspend xenbus and other devices
3 - Stop_machine, to make sure all the other vcpus are quiescent. The
Xen tools require the domain to run its save off vcpu0.
4 - Within the stop_machine state, it pins any unpinned pgds (under
construction or destruction), performs canonicalizes various other
pieces of state (mostly converting mfns to pfns), and finally
5 - Suspend the domain
Restore reverses the steps used to save the domain, ending when all
the frozen processes are thawed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When saving a domain, the Xen tools need to remap all our mfns to
portable pfns. In order to remap our p2m table, it needs to know
where all its pages are, so maintain the references to the p2m table
for it to use.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename dummy_shared_info to xen_dummy_shared_info and make it
non-static, in anticipation of users outside of enlighten.c
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We now support the use of memory hotplug, so the physical to machine
page mapping structure must be dynamic. This is implemented as a
two-level radix tree structure, which allows us to efficiently
incrementally allocate memory for the p2m table as new pages are
added.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For some perverse reason, if you call add_preferred_console() it prevents
setup_early_printk() from successfully enabling the boot console -
unless you make it a preferred console too...
Also, make xenboot console output distinct from normal console output,
since it gets repeated when the console handover happens, and the
duplicated output is confusing without disambiguation.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Without console= arguments on the kernel command line, the first
console to register becomes enabled and the preferred console (the one
behind /dev/console). This is normally tty (assuming
CONFIG_VT_CONSOLE is enabled, which it commonly is).
This is okay as long tty is a useful console. But unless we have the
PV framebuffer, and it is enabled for this domain, tty0 in domU is
merely a dummy. In that case, we want the preferred console to be the
Xen console hvc0, and we want it without having to fiddle with the
kernel command line. Commit b8c2d3dfbc
did that for us.
Since we now have the PV framebuffer, we want to enable and prefer tty
again, but only when PVFB is enabled. But even then we still want to
enable the Xen console as well.
Problem: when tty registers, we can't yet know whether the PVFB is
enabled. By the time we can know (xenstore is up), the console setup
game is over.
Solution: enable console tty by default, but keep hvc as the preferred
console. Change the preferred console to tty when PVFB probes
successfully, unless we've been given console kernel parameters.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add pte_flags() to extract the flags from a pte. This is a special
case of pte_val() which is only guaranteed to return the pte's flags
correctly; the page number may be corrupted or missing.
The intent is to allow paravirt implementations to return pte flags
without having to do any translation of the page number (most notably,
Xen).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When enabling interrupts, we don't need to worry about preemption,
because we either enter with interrupts disabled - so no preemption -
or the caller is confused and is re-enabling interrupts on some
indeterminate processor.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The guest can legitimately change things like cr4.OSFXSR and
OSXMMEXCPT, so let it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the new sched_op hypercall, mainly because xenner doesn't support
the old one.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen will trap and emulate clts, but its better to use a hypercall.
Also, xenner doesn't handle clts.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used. xen-unstable has now officially dropped
non-PAE support. Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There's no real reason we can't support sparsemem/discontigmem, so do so.
This is mostly useful to support hotplug memory.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Various places in the kernel flush the tlb even though preemption doens't
guarantee the tlb flush is happening on any particular CPU. In many cases
this doesn't seem to matter, so don't make a fuss about it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mask MCE/MCA out of cpu caps. Its harmless to leave them there, but
it does prevent the kernel from starting an unnecessary thread.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
64-bit Xen supports sysenter for 32-bit guests, so support its
use. (sysenter is faster than int $0x80 in 32-on-64.)
sysexit is still not supported, so we fake it up using iret.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename (alloc|release)_(pt|pd) to pte/pmd to explicitly match the name
of the appropriate pagetable level structure.
[ x86.git merge work by Mark McLoughlin <markmc@redhat.com> ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change iret implementation to not be dependent on direct-access vcpu
structure.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This makes the Xen console just work. Before, you had to ask for it
on the kernel command line with console=hvc0
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to set up the shared_info pointer once we've mapped the real
shared_info into its fixmap slot. That needs to happen once the general
pagetable setup has been done. Previously, the UP shared_info was set
up one in xen_start_kernel, but that was left pointing to the dummy
shared info. Unfortunately there's no really good place to do a later
setup of the shared_info in UP, so just do it once the pagetable setup
has been done.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xen_irq_enable_direct and xen_sysexit were using "andw $0x00ff,
XEN_vcpu_info_pending(vcpu)" to unmask events and test for pending ones
in one instuction.
Unfortunately, the pending flag must be modified with a locked operation
since it can be set by another CPU, and the unlocked form of this
operation was causing the pending flag to get lost, allowing the processor
to return to usermode with pending events and ultimately deadlock.
The simple fix would be to make it a locked operation, but that's rather
costly and unnecessary. The fix here is to split the mask-clearing and
pending-testing into two instructions; the interrupt window between
them is of no concern because either way pending or new events will
be processed.
This should fix lingering bugs in using direct vcpu structure access too.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix 32-on-64 pvops kernel:
we don't want userspace using syscall/sysenter, even if the hypervisor
supports it, so mask it out from CPUID.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unpin the Xen-provided pagetable once we've finished with it, so it
doesn't cause stray references which cause later swapper_pg_dir
pagetable updates to fail.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Tested-by: Jody Belka <knew-linux@pimb.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Deal properly with pmd-level pages being allocated and freed
dynamically. We can handle them more or less the same as pte pages.
Also, deal with early_ioremap pagetable manipulations.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Based on patch from Jan Beulich <jbeulich@novell.com>.
Don't rely on kmalloc(PAGE_SIZE) returning PAGE_SIZE aligned memory
(Xen requires GDT *and* LDT to be page-aligned). Using the page
allocator interface also removes the (albeit small) slab allocator
overhead. The same change being done for 64-bits for consistency.
Further, the Xen hypercall interface expects the LDT address to be
virtual, not machine.
[ Adjusted to unified ldt.c - Jeremy ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch changes the signature of write_ldt_entry.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
CC: Zachary Amsden <zach@vmware.com>
CC: Jeremy Fitzhardinge <Jeremy.Fitzhardinge.citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch changes the write_gdt_entry function signature.
Instead of the old "a" and "b" parameters, it now receives
a pointer to a desc_struct, and the size of the entry being
handled. This is because x86_64 can have some 16-byte entries
as well as 8-byte ones.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
CC: Zachary Amsden <zach@vmware.com>
CC: Jeremy Fitzhardinge <Jeremy.Fitzhardinge.citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch changes write_idt_entry signature. It now takes a gate_desc
instead of the a and b parameters. It will allow it to be later unified
between i386 and x86_64.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
CC: Zachary Amsden <zach@vmware.com>
CC: Jeremy Fitzhardinge <Jeremy.Fitzhardinge.citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch unifies struct desc_ptr between i386 and x86_64.
They can be expressed in the exact same way in C code, only
having to change the name of one of them. As Xgt_desc_struct
is ugly and big, this is the one that goes away.
There's also a padding field in i386, but it is not really
needed in the C structure definition.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This changes size-specific register names (eip/rip, esp/rsp, etc.) to
generic names in the thread and tss structures.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a lot of code which differs only by the naming of specific
members of structures that contain registers. In order to enable
additional unifications, this patch drops the e- or r- size prefix
from the register names in struct pt_regs, and drops the x- prefixes
for segment registers on the 32-bit side.
This patch also performs the equivalent renames in some additional
places that might be candidates for unification in the future.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch consolidates the irqflags include files containing common
paravirt definitions. The native definition for interrupt handling, halt,
and such, are the same for 32 and 64 bit, and they are kept in irqflags.h.
the differences are split in the arch-specific files.
The syscall function, irq_enable_sysexit, has a very specific i386 naming,
and its name is then changed to a more general one.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use u32 so 32 and 64bit have the same interface.
Andrew Morton: xen, lguest build fixes
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar