Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
The STMPE keypad controller is only used with device tree configured
systems, so force the configuration to come from device tree only, and now
actually get the rows and cols from the device tree too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
* ALSA core
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
* USB-audio
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
* FireWire
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
* HD-audio
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
* ASoC
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
* Others
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUiYaqAAoJEGwxgFQ9KSmkeo0P/2aDx2w8iVi8n7Og/7VBubkm
VZkk08IOpP3h1ojyQRsBQPI0H5AquqQTZN1TJUDcy+6PD9vckYYcag9JWhA+0RBr
I+BfTMLB3E4umIkzOjxeoyOzheL7GoZ+eZYEm8DkAhaue+cFhjNJz+S6g8ENkxJ9
lSjErXQxyiowc39I0v1WBZcuq6glX1psEsVup9U8m7KhNx6lexj28A2MkqicW4hs
DZE6pYrk57W7y3+/NWxaBiglrItvScBAPpPqoyDm9zuDNTmAtGjf1uMRmRyHe30Z
iunHXki8Fc2yBBapmfYrcLC2jyIyZykcxniF8Hd4nXUvddisFUEFFhNmB6v392d0
4/NXSqTnsq48vm0Ezjia2LySWKZZVQtam8t9262BKHcosKYObxirekD6vijSoWO8
ZWoXa+U1oWSFEoOAFDsu6GFqFHFRi5VhqBgIaPEIxrT2MQGHL3KU1bp8CJi/5CTU
pNh0wC9SMtnSJJXBIP/nYH81WQxaik3c4eiHFPN4+0McBZQiIaIqMG6x+iiVNvPB
MNLLVAzk0QiWeCmSo8OBdjOV0/T+pfQ7lrTCn2B1jdJi1CkAO8m2SwQrG4PpRx8k
lUTBd4zTx5DYR+yPF69OyoCQg0XKjW9g62Qo5rmxrQreiidROZOBS1bljWzIPeft
otupLmK5kz67n3eB2eto
=sB6v
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
- Support for specifying the target regulation mode and voltage during
system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhaLEAAoJECTWi3JdVIfQMIEH/0n/0TJngSaoifV72PCkICdx
GbNs2bUkjuNAbYw6S6xmbA6MYPEllGiFnmJPRjV41qf0a1TTG/vam3fjeaBao7En
DxEBsz22iuBM4wmOSEKTsDtTRuiX170cqKKWZ4ugFo/uaDinueW2tz0Uzvz05or5
bSxT8hbeYerNksb13mn7OjW8r0rCE24w1K669MZgwp0uuIY+NKUTnwT4TqMzDo5c
OT4RQ2XZAQOhOfqS4VTR07Ab8PzGQd4zzmTYljqd2MKL7ubKz41vNSnGHwPdrTH1
FeQ9Q/JZl0W6zwUjltGfZLjDewD1Kcb+3gdgCiD+V8wQQ1xg8H15nql4WpK6P8s=
=bMvT
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
Summary:
- Support for specifying the target regulation mode and voltage
during system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033"
* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
regulator: sky81452: Modify Device Tree structure
regulator: sky81452: Modify Device Tree structure
dt-bindings: Update documentation for "system-power-controller" and fix misspellings
of: Rename "poweroff-source" property to "system-power-controller"
regulator: max77686: Remove support for board files
regulator: max77802: Remove support for board files
regulator: max77802: Fill regulator modes translation callback
regulator: max77802: Document binding for regulator operating modes
regulator: of: Add support for parsing initial and suspend modes
regulator: of: Pass the regulator description in the match table
regulator: of: Add regulator desc param to of_get_regulator_init_data()
regulator: Add mode mapping function to struct regulator_desc
regulator: Document binding for initial and suspend modes
regulator: core: Add PRE_DISABLE notification
regulator: gpio: fix parsing of gpio list
regulator: rpm: add support for RPM-controller SMB208
regulator: da9063: Do not transform local IRQ to virtual
regulator: sky81452: Modify dependent Kconfig symbol
regulator: rt5033: Add RT5033 Regulator device driver
...
Add helper function to write u32 to registers, if we want to put u32
value to 4 continuous register, this can help us reduce tedious work.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the extra 4 channels were added to AIF2 the necessary frame control
registers were not given defaults and marked readable. This patch fixes
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These registers are documented in the datasheet and used as part of the
extcon driver. Expose them properly through regmap as the datasheet
notes they should be treated as volatile do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
ab8500_restart is not called from anywhere in the kernel, so drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix rts5227&5249 failed send buffer cmd after suspend,
PM_CTRL3 should reset before send any buffer cmd after suspend.
Otherwise, buffer cmd will failed, this will lead resume fail.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove old MAX77693_NUM_IRQ_MUIC_REGS define. Not used anywhere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The HLCDC IP available on some Atmel SoCs (i.e. at91sam9n12, at91sam9x5
family or sama5d3 family) exposes 2 subdevices:
- a display controller (controlled by a DRM driver)
- a PWM chip
The MFD device provides a regmap and several clocks (those connected
to this hardware block) to its subdevices.
This way concurrent accesses to the iomem range are handled by the regmap
framework, and each subdevice can safely access HLCDC registers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add imx6sx iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
align with freescale internal tree related GPR macro define.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:
https://www.diolan.com/i2c/i2c_interface.html.
Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.
Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.
Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.
The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hot-pluggable multi-function devices should always be registered with
PLATFORM_DEVID_AUTO to avoid name collisions on the platform bus. This
helper also hides the memory map and irq parameters, which aren't used
by hot-pluggable (e.g. USB-based) devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a header file for the max77802 constants that could be shared between
the regulator driver and Device Tree source files. Also, remove standby
and off opmodes since only normal and low power are valid operating modes.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xxsZ
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
Pull input updates from Dmitry Torokhov:
"A few new haptic/button drivers, a rudimentary support for laptops
using FocalTech touchpads; xpad driver will bind to more devices, and
a few other driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: soc_button_array - convert to platform bus
Input: palmas-pwrbutton - fix typo in the license string
Input: palmas-pwrbutton - use IRQF_ONESHOT
Input: psmouse - add support for detecting FocalTech PS/2 touchpads
Input: psmouse - add psmouse_matches_pnp_id helper function
Input: joystick - use ktime for measuring timing
Input: add haptic driver on max77693
Input: introduce palmas-pwrbutton
Input: add support for the DRV2667 haptic driver
Input: xpad - sync device IDs with xboxdrv
Input: xpad - add VID/PID for Razer Sabertooth
Input: cros_ec_keyb - optimize ghosting algorithm
Input: drv260x - fix binding document
Input: drv260x - add check for ERM mode and LRA Libraries
Input: drv260x - remove unused defines
Input: drv260x - add TI drv260x haptics driver
X-Powers AXP288 is a customized PMIC for Intel Baytrail-CR platforms. Similar
to AXP202/209, AXP288 comes with USB charger, more LDO and BUCK channels, and
AD converters. It also provides extended status and interrupt reporting
capabilities than the devices currently supported in axp20x.c.
In addition to feature extension, this patch also adds ACPI binding for
enumeration.
This consolidated driver should support more X-Powers' PMICs in both device
tree and ACPI enumerated platforms.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In <https://lkml.org/lkml/2014/6/10/265> pointed out that the 10-bit
flag in the cros_ec_tunnel was useless. It went into a 16-bit flags
field but was defined at (1 << 16).
Since we have no 10-bit i2c devices on the other side of the tunnel on
any known devices this was never a problem. Until we do it makes
sense to remove this code. On the EC side the code to handle this
flag was removed in <https://chromium-review.googlesource.com/204162>.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an MFD device is backed by ACPI namespace, we should allow subdevice
drivers to access their corresponding ACPI companion devices through normal
means (e.g using ACPI_COMPANION()).
This patch adds such support to the MFD core. If the MFD parent device
does not specify any ACPI _HID/_CID for the child device, the child
device will share the parent ACPI companion device. Otherwise the child
device will be assigned with the corresponding ACPI companion, if found
in the namespace below the parent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The logic in AFE_Pen_Ctrl bitmask in the CTRL register is different for five
wire versus four or eight wire touschscreens. This patch should fix this for
five-wire touch screens. There should be no change needed here for four and
eight wire tousch screens.
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[bigeasy: keep the change mfd only]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow regmap to provide debugfs access to the register map by telling it
what registers are valid.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds driver to support HiSilicon Hi6421 PMIC. Hi6421 includes multi-
functions, such as regulators, codec, ADCs, Coulomb counter, etc.
This driver includes core APIs _only_.
Drivers for individul components, like voltage regulators, are
implemented in corresponding driver directories and files.
Registers in Hi6421 are memory mapped, so using regmap-mmio API.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK808 chip is a power management IC for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clkout
The RK808 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Zhang Qing <zhangqing@rock-chips.com>
Tested-by: Heiko <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Current code init regmap with &da9052_regmap_config for both da9052-spi and
da9052-i2c drivers. da9052-spi sets the read_flag_mask.
The same setting may be applied for da9052-i2c if da9052-spi driver is loaded
first because they actually use the same regmap_config setting.
Fix this issue by using a local variable for regmap_config in da9052-spi driver,
so the settings in spi driver won't impact the settings in i2c driver.
Also makes da9052_regmap_config const to avoid similar issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some arizona devices have a second asynchronous sample rate, add the
registers necessary to support this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Ricoh RN5T618 is a power management IC which integrates 3 step-down
DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
fuel gauge, ADC, GPIOs and a watchdog timer.
This commit adds a MFD core driver to support the I2C communication
with the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The include guard doesn't work as intended due to the transposition
typo DAVINCI -> DAVINIC.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The header file include/linux/mfd/ti_ssp.h does not seem to be used
anywhere. It was orphaned by 3033ee62 "mfd: Remove obsolete ti-ssp
driver". Remove it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch improves support for the flash cell of
max77693 mfd by adding relevant of_compatible field
and a structure for caching related platform data.
Added are also FLASH registers related macro definitions.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to the MAX77693 documentation the name of
the register is FLASH_STATUS.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During init the core checks if the wm5102 has finished starting by reading
register 0x19 and looking at the value. This read always fails since this
is not a readable register, mark it as being one. While we're at it provide
a constant for the register name (as supplied by Charles Keepax).
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for changing the max14577 charger driver to allow
configuring battery-dependent settings from DTS.
The patch moves from regulator driver to MFD core driver and exports:
- function for calculating register value for charger's current;
- table of limits for chargers (MAX14577, MAX77836).
Previously they were used only by the max14577 regulator driver. In next
patch the charger driver will use them as well. Exporting them will
reduce unnecessary code duplication.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Torvalds