ISDv4 devices have long supported reporting data from each of two barrel
switches, but HID_DG_BARRELSWITCH2 itself was only recently standardized.
Prior to its adoption, ISDv4 devices would associate the bit indicating
the state of the second barrel switch with the "Undefined" 0x000D0000
usage. Although most such devices have explicit support, a few use the
HID_GENERIC codepath which ignores the "Undefined" usage.
This patch adds code which detects the presence of a pre-standard second
barrel switch and corrects the usage value so that the HID_GENERIC code
will declare its presence and report its state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Our loose use of "pen" and "digitizer" in the naming of several of our
vendor-defined usages may be a source of confusion given that the terms
have specific meaning within the HID specification. "Pen" specifically
refers to "an integrated display that allows the use of a stylus" (e.g.
something like a tablet PC or Cintiq) wheras "Digitizer" is a better
fit for opaque tablets like an Intuos.
While we're at it, go ahead and rename the definitions to make them more
distinct and better match up with the convention used by HID (e.g. the use
of '_UP_' for usage pages) and make them more distinct.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'oVid' and 'oPid' variables used by wacom_are_sibling are a hacky
solution to the problem of the driver historically having few good
heuristics to use in determining if two devices should be considered
siblings or not. While it works well enough for explicitly supported
devices, it offers no help for HID_GENERIC devices. Now that we have
a bit more information (e.g. direct/indirect) available to us though,
we should make use of it it to improve the pairing of such devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of displaying a generic "tablet", now g-c-c shows a pretty
"Wacom Intuos Pro S (WL)".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like upowerd is ignoring this since October 2013, so there is
no need to keep this around in the kernel.
And as mentioned in 8aaa592 (linux: Ignore ACs coming from devices) in
the upower tree, "We already have enough information on the device
battery".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When upowerd detects a new device, it tries to map this new device to
an input to guess its kind. It works OK for wired tablets when the
wireless module and its battery are attached, but not so well when
connected over wireless.
In that case, the battery is attached to the wireless HID node, not
the Pen or Pad HID node. So there is no input node as a parent of the
reported battery, which means it will be showed as a computer battery
in gnome-control-center.
If we set the power supply type to USB, upowerd has a heuristic that
detects "wacom_" in the name of the power_supply, and set the type to
tablet. So it's now clear that the reported battery of from a tablet.
(see https://cgit.freedesktop.org/upower/tree/src/linux/up-device-supply.c)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EKR switches the LED directly, and there is no point in having
userspace handling the switch it self when it's easy enough to do
in the kernel.
The other benefit is that now userspace does not need to have root access
to the LED but need only to read them with user privileges.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a bug (?) in devm_led_classdev_register() in which its increments
the refcount of the parent. If the parent is an input device, that means
the ref count never reaches 0 when devm_input_device_release() gets called.
This means that the LEDs and all the devres resources attached to the
input device are not released.
Manually force the release of the group so that the leds are released once
we are done using them.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The now obsolete sysfs files for LEDs and EKRemote are kept for backward
compatibility.
Both the EKR (read-only) and the regular Cintiqs and Intuos are now
sharing the same led API.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or Gnome complains about an empty battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, all the remotes attached to the same receiver would share the
same power_supply. That's not good as the remotes will constantly change
the battery information according to their own state.
To have something generic enough, we introduce struct wacom_battery
which regroups all the information we need for a battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres, we can now afford to create more than one input node
without having to overload the remove/failure paths. Having one input
node per remote is something which should have been implemented from start
but the probability of having users with several remotes is quite low.
Anyway, still, better looking at the future and implement things properly.
Remote input nodes will be freed/unregistered magically as they are
created in the devres group &remote->remotes[index].
We need to open the hid node now that the remotes are dynamically
allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No functional changes, just a prep patch for the one after.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will be useful when each remote will be assigned its own input device.
We won't need to unregister each input and sysfs and other elements one
at a time.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_remote_create_attr_group() and wacom_remote_destroy_attr_group()
functions were both allocating/destroying the sysfs groups but also
initializing the parameters for the remotes. Have proper functions
that can be called and extended.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres management, we don't need to remember a lot of failure
path. One or two is enough.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we want to have one input device per remote, it's better to have our
own struct wacom_remote which is dynamically allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_remote_status_irq() sends information of addition/removal of EKR.
We want to allocate one input node per remote, so better having this
in a separate worker, not handled in the IRQ directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to add an action to ensure wacom->led.groups is null when
wacom_led_control() gets called after the resources has been freed.
This also prevents to send a LED command when there is no support
from the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_release_shared_data() and wacom_remove_shared_data() are moved up
so they can be referenced in wacom_add_shared_data().
There is no point in explicitly setting wacom_wac1->shared->type to 0 in
wacom_wireless_work() (plus this would give an oops).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We started switching the driver to devres, so we should use it as much
as possible.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The sysfs group was indeed removed by kobject_put(wacom->remote_dir) in
wacom_remove(), but the name of the group was never freed.
Also remove the misplaced kobject_put(wacom->remote_dir) in the error
path of wacom_remote_create_attr_group().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use our own wacom_devm_sysfs_create_group() as there is currently no
generic one. It has been requested at least twice [1][2] but has been
always rejected.
However, in the Wacom case, for the wirelessly connected devices, we need
to be able to release the created sysfs files without removing the parent
kobject.
[1] https://patchwork.kernel.org/patch/7526551/
[2] https://lkml.org/lkml/2013/3/14/728
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We currently have a complex clean_inputs() function while this can be
handled all by devres. Set a group that we can destroy in wireless_work().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_clean_inputs() around for now as the wireless
module is using it to dynamically remove the inputs on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifying the error code paths.
We need to keep wacom_destroy_battery() around for now as the wireless
module and the remotes are using it to dynamically remove the battery
supply on disconnect.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like the battery hijacked the wireless worker. That's not fair so
use a work queue per task.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like remotes, LEDs should be handled by themself, not magically behind
the inputs as they have a complete different life.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom->remote_dir has nothing to do with inputs, so better not magically
removing it when cleaning inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The type is never set but we check for it in wacom_wireless_irq().
It looks like this is a big hack from the beginning, so fill in the gap
only.
Untested.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fuzz present on the distance and tilt axes is noticable when a puck is
present, and userspace (specifically libinput) would like the ability to
filter out the noise. To facilitate this, we assign a fuzz value of '1'
for the distance and tilt axes. This is large enough to cover most of the
natural variation in distance value as the puck is moved around, and
enough to cover the jitter in rotation (reported through tilt axes) when
the puck is left alone.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A tablet PC booted into Windows may have its pen/touch hardware switched
into "Wacom mode" similar to what we do with explicitly-supported hardware.
Some devices appear to maintain this state across reboots, preventing their
use with the generic HID driver. This patch adds support for detecting the
presence of the mode switch feature report used by devices based on the G9
and G11 chips and has the HID codepath always attempt to reset the device
back to sending standard HID reports.
Fixes: https://sourceforge.net/p/linuxwacom/bugs/307/
Fixes: https://sourceforge.net/p/linuxwacom/bugs/310/
Fixes: https://github.com/linuxwacom/input-wacom/issues/15
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 5ae6e89 introduced hid_data.inputmode with a comment that it
would have the value -1 if undefined, but then forgot to actually
perform the initialization. Although this doesn't appear to have
caused any problems in practice, it should still be remedied.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
rmmod/insmod the wacom.ko module does not work for the receiver because
it was not previously closed. Now, we can hack with the wireless receiver
without having to unplug/replug it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just some cleaning up when the input devices are unregistered.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes duplicated code.
The only difference is that we now need to stop and start the attached hid
device, but this is a small cost.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wireless_work() wants to reuse parse_and_register(), we need to have
it declared after this function.
No functional changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies the .probe() and will allow to reuse this path in the future.
Few things are reshuffled in .probe():
- init wacom struct earlier
- then retrieve the report descriptor
- then parse it and allocate/register inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The kobject_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When connecting the Cintiq Companion 2 as an external tablet (i.e., using
it in "hybrid" mode) it has been seen to cause the kernel of the machine
it is connected to to Oops. The cause has been traced to us attempting to
switch the tablet's mode prior to actually starting HID device (resulting
in the eventual dereference of the uninitialized control URB).
Commit 3b164a0 moved the mode switch from occuring post-start to occurring
pre-start. The change was not seen to cause issues largely due to the fact
that most devices mode switch with 'hid_hw_raw_request' (which is safe to
call prior to start) rather than 'hid_hw_request'.
Moving the call back to its original location resolves the issue, but
causes some touch-only Bamboo tablets (e.g. 056a:00d0) to stop working.
The affected tablets require us to perform a mode switch on their
vestigial pen interface prior ignoring with -ENODEV, meaning that the
code which is responsible for doing the ignoring has to move as well.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the Cintiq Companion Hybrid and Cintiq Companion 2 was
added (36d3c51 and f7acb55), the 'wacom_query_tablet_data' function was
updated to include references to CINTIQ_HYBRID and CINTIQ_COMPANION_2
with the thought that they were necessary to switch the touch interface
into the proper mode. This is unnecessary, however, since those types
are only ever associated with the pen interface -- the touch interfaces
are either CINTIQ_24HDT or HID_GENERIC. To avoid confusion in the future,
we remove the unnecessary CINTIQ_HYBRID and CINTIQ_COMPANION_2 conditions.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Intuos Pen in wireless mode does not have the same report id (2) as
when it is in USB mode (17).
This patch also moves WIRELESS next to REMOTE in type enum so we
can group devices with similar features easily.
Reported-by: Dale Brewe <dlbrewe@hotmail.com>
Tested-by: Dale Brewe <dlbrewe@hotmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the EMR (pen+pad) and touchscreen devices used by the
Wacom Cintiq Companion 2. This applies both to using the device as a
standalone system, as well as when operating in "Cintiq mode" (where
the EMR/touchscreen are simply exposed as USB devices to the system
its connected to).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Clifford Jolly <expiredpopsicle@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This series of devices supports both pen and touch. It reports
touch data in Bamboo3 format and pen data in Intuos pro format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Not all Bamboo support both pen and touch. Make sure we deal with
pen only and touch only devices properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device is pad (buttons) only, there is no stylus or touch. Up to
five remotes can pair with the device's associated USB dongle.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_wireless_work' function does not recalculate the tablet's
resolution, causing the value contained in the 'features' struct to
always be reported to userspace. This value is valid only for the pen
interface, meaning that the value will be incorrect for the touchpad (if
present). This in particular causes problems for libinput which relies
on the reported resolution being correct.
This patch adds the necessary calls to recalculate the resolution for
each interface. This requires a little bit of code shuffling since both
the 'wacom_set_default_phy' and 'wacom_calculate_res' are declared below
their new first point of use in 'wacom_wireless_work'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As an extension of aef3156d7, there is no sense in repeatedly calling the
'wacom_set_report' and 'wacom_get_report' functions if they return an
error. Getting an error from them implies that the device is out to lunch:
either a hard error code was returned or repeated attempts at recovering
from a "soft" error all failed. In either case, doing even more retries is
not likely to resolve whatever is wrong.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As an extension of aef3156d7, there is no sense in repeatedly calling the
'wacom_set_report' and 'wacom_get_report' functions if they return an
error. Getting an error from them implies that the device is out to lunch:
either a hard error code was returned or repeated attempts at recovering
from a "soft" error all failed. In either case, doing even more retries is
not likely to resolve whatever is wrong.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WACOM_QUIRK_NO_INPUT is a signal to the driver that input devices
should not be created for a particular device. This quirk was used by
the wireless receiver to prevent any devices from being created during
the initial probe (defering it instead until we got a tablet connection
event in 'wacom_wireless_work').
This quirk is not necessary now that a device_type is associated with each
device. Any input device allocated by 'wacom_allocate_inputs' which is
not necessary for a particular device is freed in 'wacom_register_inputs'.
In particular, none of the wireless receivers devices have the pen, pad,
or touch device types set so the same effect is achieved without the need
to be explicit.
We now return early in wacom_retrieve_hid_descriptor for wireless devices
(to prevent the device_type from being overridden) but since we ignore the
HID descriptor for the wireless reciever anyway, this is not an issue.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The monitor interface on the wireless receiver is more logically expressed
as a type of device instead of a quirk.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 01c846f introduced the 'wacom_compute_pktlen' function which
automatically determines the correct value for an interface's pkglen
by scanning the HID descriptor. This function returns the correct
value for the wireless receiver's touch interface, removing the need
for us to set it manually here.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In some cases, we need access to information before it becomes available
to the 'event' handler. In particular, for some devices we cannot properly
process the finger data without first knowing the "contact count" at the
very end of the report (e.g. the Cintiq 24HDT touch screen, when forced
through the GENERIC codepath).
Since the HID subsystem doesn't provide a way to take action before 'event'
is called, we take a cue from hid-multitouch.c and add a pre-process step
within the 'report' handler that performs the same function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Allocated input devices should not use the 'pen_name' by default since
we do not know at that point in time if that is an appropriate choice
of name. Instead, use the (tool-agnostic) name that is stored in the
device's 'wacom_features' structure. This also has the nice side-effect
of requring us to be explicit about the naming of the pen device, as
we already are for touch and pad devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The 'wacom_allocate_inputs' function tries to allocate three input devices: one
each for the pen, touch, and pad. The pointers that are returned by the
'wacom_allocate_input' calls are temporarily stored to local variables where
they are checked to ensure they're non-null before storing them in the
'wacom_wac' structure. If an allocation fails, the 'wacom_free_inputs'
function is called to reclaim the memory. Unfortunately, 'wacom_free_inputs' is
called prior to the pointers being copied, so it is not actually able to free
anything.
This patch has the calls to 'wacom_allocate_input' store the pointer directly
in the 'wacom_wac' structure where they can be freed. Also, it replaces the
call to 'wacom_free_inputs' with the (more general) 'wacom_clean_inputs' and
removes the no-longer-used function.
[jkosina@suse.com: modify to resolve conflict with 67e123f ("Delete
unnecessary checks")]
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The input_free_device() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
We can't pass a NULL to input_unregister_device().
Fixes: 2a6cdbdd4c ('HID: wacom: Introduce new 'touch_input' device')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of having a single 'input_dev' device that will take either pen
or touch data depending on the type of the device, create seperate devices
devices for each. By splitting things like this, we can support devices
(e.g. the I2C "AES" sensors in some newer tablet PCs) that send both pen
and touch reports from a single endpoint.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This splits the 'wacom_setup_pentouch_input_capabilites' function into
pieces dedicated to doing setup for just the pen interface and just
the touch interface. This makes it easier to focus on the relevant
piece when making changes.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).
To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".
Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.
This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A little bit of cleanup work for 'wacom_update_name' to make it easier on
the eyes. Creates a temporary 'name' variable on which we'll perform our
edits. Once the name is in its final form, it will be copied (with
appropriate suffix) to 'wacom_wac->name' and 'wacom_wac->pad_name'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Hardware may not respond to a request for the HID_DG_CONTACTMAX feature and
we should be tolerant of such a failure. This is especially true when using
hid-replay where the hardware doesn't exist, but also for devices attached
to a flaky bus. This patch increases the number of allowable retries to
match other calls to 'wacom_get_report' and also provides a fallback which
forces 'touch_max = 16' (enough for any Wacom device seen so far).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Retrying on -EPIPE makes very little sense since this typically indicates
a problem that will not just disappear on its own. For instance, the USB
documentation states that it will be sent if the endpoint is stalled or
the device has disconnected. Instead, we should retry if -EAGAIN is
received since this indicates a temporary error condition such as a busy
bus.
In addition to adjusting the conditions we retry under, we also log an
error on failure so that we can be aware of what's going on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The last patch was careful to maintain backwards-compatible behavior
by forcing device_type to BTN_TOOL_PEN (and printing a warning) if it
were still uninitialized after scanning the HID descriptor and applying
quirks. We should be more strict with HID_GENERIC devices, however,
since there is no a priori guarantee that it is a tablet or touchpad.
If the device_type is still uninitialized for a HID_GENERIC device then
we assume that it isn't something the driver can work with and so fail
the probe.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.
This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.
Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The naming logic currently assumes that all devices will be a pen, finger,
or pad. Though this has historically been the case, the new HID_GENERIC
catch-all may cause us to probe devices with Wacom's 056A VID which aren't
any of these types (e.g. the "Cintiq 24HDT Monitor Control"). This patch
updates the logic so that no suffix will be added to the device name if
the device type is unknown.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID generic devices share the same default name, "Wacom HID". This
causes userland programs to show same device names for different
devices, which would confuse end users with same device names for
different devices too.
This patch uses name retrieved from HID descriptor, if a meaningful
name is reported. Otherwise, affix its product ID to "Wacom HID".
Names from descriptor may contain extra whitespaces. To comfort
readers' eyes, we removed those extra whitespaces too.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
That is where they belong...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It makes probe routine easy to follow.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
The quirk was added for devices that support both pen and touch. It decides if
a device supports multiple inputs by hardcoded feature type. However, for some
devices, we do not know if they support both before accessing their HID
descriptors.
This patch relies on dynamically assigned device_type to make the decision.
Also, we make it certain that wacom_wac->shared is always created. That is, the
driver will not be loaded if it fails to create wacom_wac->shared.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If noone listens to the input device when a tool comes in proximity,
the tablet does not send the in-prox event when a client becomes available.
That means that no events will be sent until the tool is taken out of
proximity.
In this situation, ask for the report WACOM_REPORT_INTUOSREAD which will
read the corresponding feature and generate an in-prox event.
To make some generation of hardware working, we need to unset the
quirk NO_GET set by hid-core because the interfaces are seen as "boot
mouse".
We don't schedule this read in a worker while we are in an IO interrupt.
We know that usbhid will do it asynchronously. If this is triggered by
uhid, then this is obviously a client side bug :)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.
The power_supply_register() function is changed so all power supply
drivers need updating.
When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.
When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
[for drivers/hid/*]
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.
Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The status packet for tablets which can use a wireless module contains a
bit that is set if the battery is charging. This bit will be 0 if either
a battery is not present or if the battery has reached full charge. Note
that the charging circuit may continue to charge the battery for a short
time after reaching "100%".
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tablets like the Intuos, Intuos Pro, and Bamboo have a connector for an
optional wireless module that can be connected on the fly. The presence
(or absence) of this module is indicated in a status report recieved
from the tablet. This patch adds a workqueue function that will create
or destroy a power_supply object at runtime to match the current state
of the WACOM_QUIRK_BATTERY flag.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stylus of this device works just fine out of the box.
The touch is seen by default as a mouse with relative events and some
gestures.
The wireless and the wired version have slightly different firmwares, but
the debug mode 2 on the feature 2 is common to the 2 devices. In this mode,
all the reports are emitted through the debug interface (pen, raw touch
and mouse emulation), so we have to re-route manually the events.
We keep the Pen interface as a HID_GENERIC one because it works, and only
parse the raw touches while discarding the mouse emulation & gestures.
Switching the default in raw mode allows us to have a consistent user
experience accross all the multitouch touchpads (and enable the touch part
of the devices).
Note that the buttons of this devices are reported through the touch
interface. There is no 'Pad' interface. It seemed more natural to have
the BTN_LEFT and BTN_RIGHT reported with the touch because they are
placed under the touch interface and it looks like they belong to the
touch part.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Bamboo PAD in debug mode needs to re-route events from the debug
interface to the Pen interface. This can be easily done with
hid_input_report(), but that means that we need to keep a reference to
the various hid_devices.
There should be only one touch and one pen interface per physical tablet,
so there is no need to keep a list of hid-devices, plain pointers are
sufficient.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.
wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).
That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a HID descriptor places HID_DG_CONTACTID before HID_DG_X and HID_DG_Y then
the ABS_X and ABS_Y will not be automatically initialized by the call to
input_mt_init_slots. To ensure that this is not a problem, we relocate that
call to occur after HID parsing has been completed and we've initalized all the
multitouch axes.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the conversion from USB to HID (in v3.17), some people reported a
freeze on boot with the wacom driver. Hans managed to get a stacktrace:
[ 240.272331] Call Trace:
[ 240.272338] [<ffffffff813de7b9>] ? usb_hcd_submit_urb+0xa9/0xb10
[ 240.272347] [<ffffffff81555579>] schedule+0x29/0x70
[ 240.272355] [<ffffffff815559e6>] schedule_preempt_disabled+0x16/0x20
[ 240.272363] [<ffffffff81557365>] __mutex_lock_slowpath+0xe5/0x230
[ 240.272372] [<ffffffff815574c7>] mutex_lock+0x17/0x30
[ 240.272380] [<ffffffffa063c1d2>] wacom_resume+0x22/0x50 [wacom]
[ 240.272396] [<ffffffffa01aea8a>] hid_resume_common+0xba/0x110 [usbhid]
[ 240.272404] [<ffffffff813e5890>] ? usb_runtime_suspend+0x80/0x80
[ 240.272417] [<ffffffffa01aeb1d>] hid_resume+0x3d/0x70 [usbhid]
[ 240.272425] [<ffffffff813e44a6>] usb_resume_interface.isra.6+0xb6/0x120
[ 240.272432] [<ffffffff813e4774>] usb_resume_both+0x74/0x140
[ 240.272439] [<ffffffff813e58aa>] usb_runtime_resume+0x1a/0x20
[ 240.272446] [<ffffffff813b1912>] __rpm_callback+0x32/0x70
[ 240.272453] [<ffffffff813b1976>] rpm_callback+0x26/0xa0
[ 240.272460] [<ffffffff813b2d71>] rpm_resume+0x4b1/0x690
[ 240.272468] [<ffffffff812ab992>] ? radix_tree_lookup_slot+0x22/0x50
[ 240.272475] [<ffffffff813b2c1a>] rpm_resume+0x35a/0x690
[ 240.272482] [<ffffffff8116e9c9>] ? zone_statistics+0x89/0xa0
[ 240.272489] [<ffffffff813b2f90>] __pm_runtime_resume+0x40/0x60
[ 240.272497] [<ffffffff813e4272>] usb_autopm_get_interface+0x22/0x60
[ 240.272509] [<ffffffffa01ae8d9>] usbhid_open+0x59/0xe0 [usbhid]
[ 240.272517] [<ffffffffa063ac85>] wacom_open+0x35/0x50 [wacom]
[ 240.272525] [<ffffffff813f37b9>] input_open_device+0x79/0xa0
[ 240.272534] [<ffffffffa048d1c1>] evdev_open+0x1b1/0x200 [evdev]
[ 240.272543] [<ffffffff811c899e>] chrdev_open+0xae/0x1f0
[ 240.272549] [<ffffffff811c88f0>] ? cdev_put+0x30/0x30
[ 240.272556] [<ffffffff811c17e2>] do_dentry_open+0x1d2/0x320
[ 240.272562] [<ffffffff811c1cd1>] finish_open+0x31/0x50
[ 240.272571] [<ffffffff811d2202>] do_last.isra.36+0x652/0xe50
[ 240.272579] [<ffffffff811d2ac7>] path_openat+0xc7/0x6f0
[ 240.272586] [<ffffffff811cf012>] ? final_putname+0x22/0x50
[ 240.272594] [<ffffffff811d42d2>] ? user_path_at_empty+0x72/0xd0
[ 240.272602] [<ffffffff811d43fd>] do_filp_open+0x4d/0xc0
[...]
So here, wacom_open is called, and then wacom_resume is called by the
PM system. However, wacom_open already took the lock when wacom_resume
tries to get it. Freeze.
A little bit of history shows that this already happened in the past
- commit f6cd378372 ("Input: wacom - fix runtime PM related deadlock"),
and the solution was to call first the PM function before taking the lock.
The lock was introduced in commit commit e722409445 ("Input: wacom -
implement suspend and autosuspend") when the autosuspend feature has
been added. Given that usbhid already takes care of this very same
locking between suspend/resume, I think we can simply kill the lock
in open/close.
The lock is now used also with LEDs, so we can not remove it completely.
Reported-by: Hans Spath <inbox-546@hans-spath.de>
Tested-by: Hans Spath <inbox-546@hans-spath.de>
CC: stable@vger.kernel.org # v3.17+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo models do not support HID_DG_CONTACTMAX. Plus, Bamboo pen-only
has touch descriptor. This leads to some complications in the code.
This patch also fixes duplicated PAD interfeaces for Intuos Pen
models.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.
This patch implements the pen support only. The finger part will come in
a later patch.
To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows to have the input devices ready in while parsing the reports
descriptor.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If the input can be created earlier during probe, we can already populate
them while reading the report descriptor. This way, we can rely on the
hid subsystem directly for tablets which already provide a meaningful
report descriptor (like ISDv4-5).
This patch only splits the allocation and registration, but do not
change where we allocate the input. This will come in a later patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When we have to deal with new elements in probe, having the exit labels
named sequencially is a pain to maintain. Put a meaningful name instead
so that we do not have to renumber them on inserts.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom tablets (at least the ISDv4 found in the Lenovo X230) timeout
during probe while retrieving the input reports.
The only time this information is valuable is during the feature_mapping
stage, so we can ask for it there and discard the generic input reports
retrieval.
This gives a code path closer to the wacom.ko driver when it was in the
input subtree (not HID).
Cc: stable@vger.kernel.org # requires cherry-pick of c64d883476
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, tablets connected to the WL receiver all share the same
VID/PID. There is no way for the user space to know which one is which
besides parsing the name. We can force the PID to be set to the
actual hardware. This way, the input device will have the correct PID
which can be match in libwacom.
With only this trick, the pad input does not inherit the ID_INPUT_TABLET
udev property from its parent. We can force udev to accept it by declaring
a BTN_STYLUS which is never used.
This way, tablets connected through WL can be used from the user point of
view in the same way they are used while connected through wire.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke