With the advent of small rto timers in datacenter TCP,
(ip route ... rto_min x), the following can happen :
1) Qdisc is full, transmit fails.
TCP sets a timer based on icsk_rto to retry the transmit, without
exponential backoff.
With low icsk_rto, and lot of sockets, all cpus are servicing timer
interrupts like crazy.
Intent of the code was to retry with a timer between 200 (TCP_RTO_MIN)
and 500ms (TCP_RESOURCE_PROBE_INTERVAL)
2) Receivers can send zero windows if they don't drain their receive queue.
TCP sends zero window probes, based on icsk_rto current value, with
exponential backoff.
With /proc/sys/net/ipv4/tcp_retries2 being 15 (or even smaller in
some cases), sender can abort in less than one or two minutes !
If receiver stops the sender, it obviously doesn't care of very tight
rto. Probability of dropping the ACK reopening the window is not
worth the risk.
Lets change the base timer to be at least 200ms (TCP_RTO_MIN) for these
events (but not normal RTO based retransmits)
A followup patch adds a new SNMP counter, as it would have helped a lot
diagnosing this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows a server application to get the TCP SYN headers for
its passive connections. This is useful if the server is doing
fingerprinting of clients based on SYN packet contents.
Two socket options are added: TCP_SAVE_SYN and TCP_SAVED_SYN.
The first is used on a socket to enable saving the SYN headers
for child connections. This can be set before or after the listen()
call.
The latter is used to retrieve the SYN headers for passive connections,
if the parent listener has enabled TCP_SAVE_SYN.
TCP_SAVED_SYN is read once, it frees the saved SYN headers.
The data returned in TCP_SAVED_SYN are network (IPv4/IPv6) and TCP
headers.
Original patch was written by Tom Herbert, I changed it to not hold
a full skb (and associated dst and conntracking reference).
We have used such patch for about 3 years at Google.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
-----BEGIN PGP SIGNATURE-----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=sf/A
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-05-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have only a few fixes right now:
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-04
Here's the first bluetooth-next pull request for 4.2:
- Various fixes for at86rf230 driver
- ieee802154: trace events support for rdev->ops
- HCI UART driver refactoring
- New Realtek IDs added to btusb driver
- Off-by-one fix for rtl8723b in btusb driver
- Refactoring of btbcm driver for both UART & USB use
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate 90 of these warnings:
Warning(..//include/net/mac80211.h:1682): No description found for parameter 'drv_priv[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some users of flow keys (well just sch_choke now) need to pass
flow_keys in skbuff cb, and use them for exact comparisons of flows
so that skb->hash is not sufficient. In order to increase size of
the flow_keys structure, we introduce another structure for
the purpose of passing flow keys in skbuff cb. We limit this structure
to sixteen bytes, and we will technically treat this as a digest of
flow_keys struct hence its name flow_keys_digest. In the first
incaranation we just copy the flow_keys structure up to 16 bytes--
this is the same information previously passed in the cb. In the
future, we'll adapt this for larger flow_keys and could use something
like SHA-1 over the whole flow_keys to improve the quality of the
digest.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under presence of TSO/GSO/GRO packets, codel at low rates can be quite
useless. In following example, not a single packet was ever dropped,
while average delay in codel queue is ~100 ms !
qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
Sent 134376498 bytes 88797 pkt (dropped 0, overlimits 0 requeues 0)
backlog 13626b 3p requeues 0
count 0 lastcount 0 ldelay 96.9ms drop_next 0us
maxpacket 9084 ecn_mark 0 drop_overlimit 0
This comes from a confusion of what should be the minimal backlog. It is
pretty clear it is not 64KB or whatever max GSO packet ever reached the
qdisc.
codel intent was to use MTU of the device.
After the fix, we finally drop some packets, and rtt/cwnd of my single
TCP flow are meeting our expectations.
qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
Sent 102798497 bytes 67912 pkt (dropped 1365, overlimits 0 requeues 0)
backlog 6056b 3p requeues 0
count 1 lastcount 1 ldelay 36.3ms drop_next 0us
maxpacket 10598 ecn_mark 0 drop_overlimit 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Van Jacobson <vanj@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch divides the IPv6 flow label space into two ranges:
0-7ffff is reserved for flow label manager, 80000-fffff will be
used for creating auto flow labels (per RFC6438). This only affects how
labels are set on transmit, it does not affect receive. This range split
can be disbaled by systcl.
Background:
IPv6 flow labels have been an unmitigated disappointment thus far
in the lifetime of IPv6. Support in HW devices to use them for ECMP
is lacking, and OSes don't turn them on by default. If we had these
we could get much better hashing in IPv6 networks without resorting
to DPI, possibly eliminating some of the motivations to to define new
encaps in UDP just for getting ECMP.
Unfortunately, the initial specfications of IPv6 did not clarify
how they are to be used. There has always been a vague concept that
these can be used for ECMP, flow hashing, etc. and we do now have a
good standard how to this in RFC6438. The problem is that flow labels
can be either stateful or stateless (as in RFC6438), and we are
presented with the possibility that a stateless label may collide
with a stateful one. Attempts to split the flow label space were
rejected in IETF. When we added support in Linux for RFC6438, we
could not turn on flow labels by default due to this conflict.
This patch splits the flow label space and should give us
a path to enabling auto flow labels by default for all IPv6 packets.
This is an API change so we need to consider compatibility with
existing deployment. The stateful range is chosen to be the lower
values in hopes that most uses would have chosen small numbers.
Once we resolve the stateless/stateful issue, we can proceed to
look at enabling RFC6438 flow labels by default (starting with
scaled testing).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not used.
pedit sets TC_MUNGED when packet content was altered, but all the core
does is unset MUNGED again and then set OK2MUNGE.
And the latter isn't tested anywhere. So lets remove both
TC_MUNGED and TC_OK2MUNGE.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
_rt6i_peer is no longer needed after the last patch,
'ipv6: Stop rt6_info from using inet_peer's metrics'.
DST_METRICS_FORCE_OVERWRITE is added by
commit e5fd387ad5 ("ipv6: do not overwrite inetpeer metrics prematurely").
Since inetpeer is no longer used for metrics, this bit is also not needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Michal Kubeček <mkubecek@suse.cz>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_peer is indexed by the dst address alone. However, the fib6 tree
could have multiple routing entries (rt6_info) for the same dst. For
example,
1. A /128 dst via multiple gateways.
2. A RTF_CACHE route cloned from a /128 route.
In the above cases, all of them will share the same metrics and
step on each other.
This patch will steer away from inet_peer's metrics and use
dst_cow_metrics_generic() for everything.
Change Highlights:
1. Remove rt6_cow_metrics() which currently acquires metrics from
inet_peer for DST_HOST route (i.e. /128 route).
2. Add rt6i_pmtu to take care of the pmtu update to avoid creating a
full size metrics just to override the RTAX_MTU.
3. After (2), the RTF_CACHE route can also share the metrics with its
dst.from route, by:
dst_init_metrics(&cache_rt->dst, dst_metrics_ptr(cache_rt->dst.from), true);
4. Stop creating RTF_CACHE route by cloning another RTF_CACHE route. Instead,
directly clone from rt->dst.
[ Currently, cloning from another RTF_CACHE is only possible during
rt6_do_redirect(). Also, the old clone is removed from the tree
immediately after the new clone is added. ]
In case of cloning from an older redirect RTF_CACHE, it should work as
before.
In case of cloning from an older pmtu RTF_CACHE, this patch will forget
the pmtu and re-learn it (if there is any) from the redirected route.
The _rt6i_peer and DST_METRICS_FORCE_OVERWRITE will be removed
in the next cleanup patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is based on commit 6bab2e19c5
("cfg80211: pass name_assign_type to rdev_add_virtual_intf()")
This will expose in sysfs whether the ifname of a IEEE-802.15.4
device is set by userspace or generated by the kernel.
We are using two types of name_assign_types
o NET_NAME_ENUM: Default interface name provided by kernel
o NET_NAME_USER: Interface name provided by user.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the proper description to the mac802154 core APIs.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We would like that optional info provided by Congestion Control
modules using netlink can also be read using getsockopt()
This patch changes get_info() to put this information in a buffer,
instead of skb, like tcp_get_info(), so that following patch
can reuse this common infrastructure.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tracks total number of bytes acked for a TCP socket.
This is the sum of all changes done to tp->snd_una, and allows
for precise tracking of delivered data.
RFC4898 named this : tcpEStatsAppHCThruOctetsAcked
This is a 64bit field, and can be fetched both from TCP_INFO
getsockopt() if one has a handle on a TCP socket, or from inet_diag
netlink facility (iproute2/ss patch will follow)
Note that tp->bytes_acked was placed near tp->snd_una for
best data locality and minimal performance impact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Eric Salo <salo@google.com>
Cc: Martin Lau <kafai@fb.com>
Cc: Chris Rapier <rapier@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding modules currently defines four macros with
general names that pollute the global namespace:
DRV_VERSION
DRV_RELDATE
DRV_NAME
DRV_DESCRIPTION
Fixing that by defining a private bonding_priv.h
header files which includes those defines.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ 3897.923145] BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
[ 3897.931025] IP: [<ffffffffa9f27686>] reqsk_timer_handler+0x1a6/0x243
There is a race when reqsk_timer_handler() and tcp_check_req() call
inet_csk_reqsk_queue_unlink() on the same req at the same time.
Before commit fa76ce7328 ("inet: get rid of central tcp/dccp listener
timer"), listener spinlock was held and race could not happen.
To solve this bug, we change reqsk_queue_unlink() to not assume req
must be found, and we return a status, to conditionally release a
refcount on the request sock.
This also means tcp_check_req() in non fastopen case might or not
consume req refcount, so tcp_v6_hnd_req() & tcp_v4_hnd_req() have
to properly handle this.
(Same remark for dccp_check_req() and its callers)
inet_csk_reqsk_queue_drop() is now too big to be inlined, as it is
called 4 times in tcp and 3 times in dccp.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When frames time out in the reordering buffer, it is a
good indication that something went wrong and the driver
may want to know about that to take action or trigger
debug flows.
It is pointless to notify the driver about each frame that
is released. Notify each time the timer fires.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we receive a BAR, this typically means that our peer
doesn't hear our Block-Acks or that we can't hear its
frames. Either way, it is a good indication that the link
is in a bad condition. This is why it can serve as a probe
to the driver.
Use the event_callback callback for this.
Since more events with the same data will be added in the
feature, the structure that describes the data attached to
the event is called in a generic name: ieee80211_ba_event.
This also means that from now on, the event_callback can't
sleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drivers want to support S/G (really just gather DMA on TX) then
we can now easily support this on the fast-xmit path since it just
needs to write to the ethernet header (and already has a check for
that being possible.)
However, disallow this on the regular TX path (which has to handle
fragmentation, software crypto, etc.) by calling skb_linearize().
Also allow the related HIGHDMA since that's not interesting to the
code in mac80211 at all anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to speed up mac80211's TX path, add the "fast-xmit" cache
that will cache the data frame 802.11 header and other data to be
able to build the frame more quickly. This cache is rebuilt when
external triggers imply changes, but a lot of the checks done per
packet today are simplified away to the check for the cache.
There's also a more detailed description in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A couple of enums in mac80211.h became structures recently, but the
comments didn't follow suit, leading to errors like:
Error(.//include/net/mac80211.h:367): Cannot parse enum!
Documentation/DocBook/Makefile:93: recipe for target 'Documentation/DocBook/80211.xml' failed
make[1]: *** [Documentation/DocBook/80211.xml] Error 1
Makefile:1361: recipe for target 'mandocs' failed
make: *** [mandocs] Error 2
Fix the comments comments accordingly. Added a couple of other small
comment fixes while I was there to silence other recently-added docbook
warnings.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
This inline has ~500 callsites.
On 04/14/2015 08:37 PM, David Miller wrote:
> That BUG_ON() was added 7 years ago, and I don't remember it ever
> triggering or helping us diagnose something, so just remove it and
> keep the function inlined.
On x86 allyesconfig build:
text data bss dec hex filename
82447071 22255384 20627456 125329911 77861f7 vmlinux4
82441375 22255384 20627456 125324215 7784bb7 vmlinux5prime
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: David S. Miller <davem@davemloft.net>
CC: Jan Engelhardt <jengelh@medozas.de>
CC: Jiri Pirko <jpirko@redhat.com>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different problems are fixed here :
1) inet_sk_diag_fill() might be called without socket lock held.
icsk->icsk_ca_ops can change under us and module be unloaded.
-> Access to freed memory.
Fix this using rcu_read_lock() to prevent module unload.
2) Some TCP Congestion Control modules provide information
but again this is not safe against icsk->icsk_ca_ops
change and nla_put() errors were ignored. Some sockets
could not get the additional info if skb was almost full.
Fix this by returning a status from get_info() handlers and
using rcu protection as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A final pull request, I know it's very late but this time I think it's worth a
bit of rush.
The following patchset contains Netfilter/nf_tables updates for net-next, more
specifically concatenation support and dynamic stateful expression
instantiation.
This also comes with a couple of small patches. One to fix the ebtables.h
userspace header and another to get rid of an obsolete example file in tree
that describes a nf_tables expression.
This time, I decided to paste the original descriptions. This will result in a
rather large commit description, but I think these bytes to keep.
Patrick McHardy says:
====================
netfilter: nf_tables: concatenation support
The following patches add support for concatenations, which allow multi
dimensional exact matches in O(1).
The basic idea is to split the data registers, currently consisting of
4 registers of 16 bytes each, into smaller units, 16 registers of 4
bytes each, and making sure each register store always leaves the
full 32 bit in a well defined state, meaning smaller stores will
zero the remaining bits.
Based on that, we can load multiple adjacent registers with different
values, thereby building a concatenated bigger value, and use that
value for set lookups.
Sets are changed to use variable sized extensions for their key and
data values, removing the fixed limit of 16 bytes while saving memory
if less space is needed.
As a side effect, these patches will allow some nice optimizations in
the future, like using jhash2 in nft_hash, removing the masking in
nft_cmp_fast, optimized data comparison using 32 bit word size etc.
These are not done so far however.
The patches are split up as follows:
* the first five patches add length validation to register loads and
stores to make sure we stay within bounds and prepare the validation
functions for the new addressing mode
* the next patches prepare for changing to 32 bit addressing by
introducing a struct nft_regs, which holds the verdict register as
well as the data registers. The verdict members are moved to a new
struct nft_verdict to allow to pull struct nft_data out of the stack.
* the next patches contain preparatory conversions of expressions and
sets to use 32 bit addressing
* the next patch introduces so far unused register conversion helpers
for parsing and dumping register numbers over netlink
* following is the real conversion to 32 bit addressing, consisting of
replacing struct nft_data in struct nft_regs by an array of u32s and
actually translating and validating the new register numbers.
* the final two patches add support for variable sized data items and
variable sized keys / data in set elements
The patches have been verified to work correctly with nft binaries using
both old and new addressing.
====================
Patrick McHardy says:
====================
netfilter: nf_tables: dynamic stateful expression instantiation
The following patches are the grand finale of my nf_tables set work,
using all the building blocks put in place by the previous patches
to support something like iptables hashlimit, but a lot more powerful.
Sets are extended to allow attaching expressions to set elements.
The dynset expression dynamically instantiates these expressions
based on a template when creating new set elements and evaluates
them for all new or updated set members.
In combination with concatenations this effectively creates state
tables for arbitrary combinations of keys, using the existing
expression types to maintain that state. Regular set GC takes care
of purging expired states.
We currently support two different stateful expressions, counter
and limit. Using limit as a template we can express the functionality
of hashlimit, but completely unrestricted in the combination of keys.
Using counter we can perform accounting for arbitrary flows.
The following examples from patch 5/5 show some possibilities.
Userspace syntax is still WIP, especially the listing of state
tables will most likely be seperated from normal set listings
and use a more structured format:
1. Limit the rate of new SSH connections per host, similar to iptables
hashlimit:
flow ip saddr timeout 60s \
limit 10/second \
accept
2. Account network traffic between each set of /24 networks:
flow ip saddr & 255.255.255.0 . ip daddr & 255.255.255.0 \
counter
3. Account traffic to each host per user:
flow skuid . ip daddr \
counter
4. Account traffic for each combination of source address and TCP flags:
flow ip saddr . tcp flags \
counter
The resulting set content after a Xmas-scan look like this:
{
192.168.122.1 . fin | psh | urg : counter packets 1001 bytes 40040,
192.168.122.1 . ack : counter packets 74 bytes 3848,
192.168.122.1 . psh | ack : counter packets 35 bytes 3144
}
In the future the "expressions attached to elements" will be extended
to also support user created non-stateful expressions to allow to
efficiently select beween a set of parameter sets, f.i. a set of log
statements with different prefixes based on the interface, which currently
require one rule each. This will most likely have to wait until the next
kernel version though.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro says:
====================
netdev-related stuff in vfs.git
There are several commits sitting in vfs.git that probably ought to go in
via net-next.git. First of all, there's merge with vfs.git#iocb - that's
Christoph's aio rework, which has triggered conflicts with the ->sendmsg()
and ->recvmsg() patches a while ago. It's not so much Christoph's stuff
that ought to be in net-next, as (pretty simple) conflict resolution on merge.
The next chunk is switch to {compat_,}import_iovec/import_single_range - new
safer primitives for initializing iov_iter. The primitives themselves come
from vfs/git#iov_iter (and they are used quite a lot in vfs part of queue),
conversion of net/socket.c syscalls belongs in net-next, IMO. Next there's
afs and rxrpc stuff from dhowells. And then there's sanitizing kernel_sendmsg
et.al. + missing inlined helper for "how much data is left in msg->msg_iter" -
this stuff is used in e.g. cifs stuff, but it belongs in net-next.
That pile is pullable from
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs.git for-davem
I'll post the individual patches in there in followups; could you take a look
and tell if everything in there is OK with you?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a timer wheel for timewait sockets was nice ~15 years ago when
memory was expensive and machines had a single processor.
This does not scale, code is ugly and source of huge latencies
(Typically 30 ms have been seen, cpus spinning on death_lock spinlock.)
We can afford to use an extra 64 bytes per timewait sock and spread
timewait load to all cpus to have better behavior.
Tested:
On following test, /proc/sys/net/ipv4/tcp_tw_recycle is set to 1
on the target (lpaa24)
Before patch :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
419594
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
437171
While test is running, we can observe 25 or even 33 ms latencies.
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20601ms
rtt min/avg/max/mdev = 0.020/0.217/25.771/1.535 ms, pipe 2
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20702ms
rtt min/avg/max/mdev = 0.019/0.183/33.761/1.441 ms, pipe 2
After patch :
About 90% increase of throughput :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
810442
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
800992
And latencies are kept to minimal values during this load, even
if network utilization is 90% higher :
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 19991ms
rtt min/avg/max/mdev = 0.023/0.064/0.360/0.042 ms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to mark stateful expressions.
This is used for dynamic expression instanstiation to limit the usable
expressions. Strictly speaking only the dynset expression can not be
used in order to avoid recursion, but since dynamically instantiating
non-stateful expressions will simply create an identical copy, which
behaves no differently than the original, this limits to expressions
where it actually makes sense to dynamically instantiate them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Preparation to attach expressions to set elements: add a set extension
type to hold an expression and dump the expression information with the
set element.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper functions for initializing, cloning, dumping and destroying
a single expression that is not part of a rule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch changes sets to support variable sized set element keys / data
up to 64 bytes each by using variable sized set extensions. This allows
to use concatenations with bigger data items suchs as IPv6 addresses.
As a side effect, small keys/data now don't require the full 16 bytes
of struct nft_data anymore but just the space they need.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a size argument to nft_data_init() and pass in the available space.
This will be used by the following patches to support variable sized
set element data.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper functions to parse and dump register values in netlink attributes.
These helpers will later be changed to take care of translation between the
old 128 bit and the new 32 bit register numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simple conversion to use u32 pointers to the beginning of the data
area to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Only needlessly complicates things due to requiring specific argument
types. Use memcmp directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Change nft_validate_input_register() to not only validate the input
register number, but also the length of the load, and rename it to
nft_validate_register_load() to reflect that change.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All users of nft_validate_register_store() first invoke
nft_validate_output_register(). There is in fact no use for using it
on its own, so simplify the code by folding the functionality into
nft_validate_register_store() and kill it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The existing name is ambiguous, data is loaded as well when we read from
a register. Rename to nft_validate_register_store() for clarity and
consistency with the upcoming patch to introduce its counterpart,
nft_validate_register_load().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For values spanning multiple registers, we need to validate that enough
space is available from the destination register onwards. Add a len
argument to nft_validate_data_load() and consolidate the existing length
validations in preparation of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* new mac80211 internal software queue to allow drivers to have
shorter hardware queues and pull on-demand
* use rhashtable for mac80211 station table
* minstrel rate control debug improvements and some refactoring
* fix noisy message about TX power reduction
* fix continuous message printing and activity if CRDA doesn't respond
* fix VHT-related capabilities with "iw connect" or "iwconfig ..."
* fix Kconfig for cfg80211 wireless extensions compatibility
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJVJ7CPAAoJEDBSmw7B7bqr8+IQAKCAbUyd6PFRT5tcz9kW5GCW
/ibb+n1e14yWKgNEe1gddUGKG/L3HGCBXNkCYzR2M8mlL7dLPqspaBcGHS4dx8F4
D0AuikqvtXIxfAXi0zmU2uo7rH7u2X34R2LtS8AlKByD+jmFvxMiPPvxNFgzJu/7
63UQm73p2pnu/KdXLW1OQEcpZtZJ9+N/uBiq9zbVdX3A8T84ME0oMyy+EAQqCZdK
CcsTXHCnAgmmXWJlu1JRdopr1bd38mSGB70eXduFtPqDdmtQRnoaCQ9e+tJDA4j4
svEw0yDmsc4WG1EKLKKCRd3uFOZsng+lcXrHfpm5wlSPpCOItfQ9BzT3x1u6Y5JU
Z1WMOMkkEce+95U7/RLoXwC/2RS3XelUXTde4cGIRMvO5drOrU58P0gdn3J+yKbv
6v+2GGKy/39tdXUOxIl3EZT/huIl+h1UNO8C2hyaEwdXK+X1zl31/u6kk1Ns18Wr
YPEJixxHx0zR8jaZgDC7OlWLuqn4Ay+Ls9yCyIesdHzKpizJKqn83PntYnpJmxoA
9hlIyRDWnqH44KxzB85ni1C2Qudec3mcCWIWV7M+UoSC1Cgs/LxDzH7kRejR2ZIl
vRhg5pqyr53L0h2lq5DO4Cj4UzbXb7YioKJRxjyKloNOlRrCZtK/VEsHbdsKEcIp
d/wHj1AyFZeQfuhk8Qqr
=mtuo
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
There isn't much left, but we have
* new mac80211 internal software queue to allow drivers to have
shorter hardware queues and pull on-demand
* use rhashtable for mac80211 station table
* minstrel rate control debug improvements and some refactoring
* fix noisy message about TX power reduction
* fix continuous message printing and activity if CRDA doesn't respond
* fix VHT-related capabilities with "iw connect" or "iwconfig ..."
* fix Kconfig for cfg80211 wireless extensions compatibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-04-09
We've had enough new patches during the past week (especially from
Marcel) that it'd be good to still get these queued for 4.1.
The majority of the changes are from Marcel with lots of cleanup &
refactoring patches for the HCI UART driver. Marcel also split out some
Broadcom & Intel vendor specific functionality into two new btintel &
btbcm modules.
In addition to the HCI driver changes there's the completion of our
local OOB data interface for pairing, added support for requesting
remote LE features when connecting, as well as a couple of minor fixes
for mac802154.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink attribute for the power is s8. But for the driver level
operations we are collection power level value into integer.
It has to be change to s8 from int.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When establishing a Bluetooth LE connection, read the remote used
features mask to determine which features are supported. This was
not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and
also 4.2 have introduced new optional features, this becomes more
important.
This works the same as with BR/EDR where the connection enters the
BT_CONFIG stage and hci_connect_cfm call is delayed until the remote
features have been retrieved. Only after successfully receiving the
remote features, the connection enters the BT_CONNECTED state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
trivial conflict in net/socket.c and non-trivial one in crypto -
that one had evaded aio_complete() removal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MzOJ
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC: 4.1 pull request
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an userdata set extension and allow the user to attach arbitrary
data to set elements. This is intended to hold TLV encoded data like
comments or DNS annotations that have no meaning to the kernel.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a new "dynset" expression for dynamic set updates.
A new set op ->update() is added which, for non existant elements,
invokes an initialization callback and inserts the new element.
For both new or existing elements the extenstion pointer is returned
to the caller to optionally perform timer updates or other actions.
Element removal is not supported so far, however that seems to be a
rather exotic need and can be added later on.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently a set binding is assumed to be related to a lookup and, in
case of maps, a data load.
In order to use bindings for set updates, the loop detection checks
must be restricted to map operations only. Add a flags member to the
binding struct to hold the set "action" flags such as NFT_SET_MAP,
and perform loop detection based on these.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use atomic operations for the element count to avoid races with async
updates.
To properly handle the transactional semantics during netlink updates,
deleted but not yet committed elements are accounted for seperately and
are treated as being already removed. This means for the duration of
a netlink transaction, the limit might be exceeded by the amount of
elements deleted. Set implementations must be prepared to handle this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fast Open has been using an experimental option with a magic number
(RFC6994). This patch makes the client by default use the RFC7413
option (34) to get and send Fast Open cookies. This patch makes
the client solicit cookies from a given server first with the
RFC7413 option. If that fails to elicit a cookie, then it tries
the RFC6994 experimental option. If that also fails, it uses the
RFC7413 option on all subsequent connect attempts. If the server
returns a Fast Open cookie then the client caches the form of the
option that successfully elicited a cookie, and uses that form on
later connects when it presents that cookie.
The idea is to gradually obsolete the use of experimental options as
the servers and clients upgrade, while keeping the interoperability
meanwhile.
Signed-off-by: Daniel Lee <Longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Open has been using the experimental option with a magic number
(RFC6994) to request and grant Fast Open cookies. This patch enables
the server to support the official IANA option 34 in RFC7413 in
addition.
The change has passed all existing Fast Open tests with both
old and new options at Google.
Signed-off-by: Daniel Lee <Longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Bluetooth 4.1 there are two additional values for SSP OOB data,
namely C-256 and R-256. This patch updates the EIR definitions to take
into account both the 192 and 256 bit variants of C and R.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hci_recv_stream_fragment function should have never been introduced
in the first place. The Bluetooth core does not need to know anything
about the HCI transport protocol.
With all transport protocol specific detailed moved back into the
drivers where they belong (mainly generic USB and UART drivers), this
function can now be removed.
This reduces the size of hci_dev structure and also removes an exported
symbol from the Bluetooth core module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The data pointer provided to hci_recv_stream_fragment function should
have been marked const. The function has no business in modifying the
original data. So fix this now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-04-04
Here's what's probably the last bluetooth-next pull request for 4.1:
- Fixes for LE advertising data & advertising parameters
- Fix for race condition with HCI_RESET flag
- New BNEPGETSUPPFEAT ioctl, needed for certification
- New HCI request callback type to get the resulting skb
- Cleanups to use BIT() macro wherever possible
- Consolidate Broadcom device entries in the btusb HCI driver
- Check for valid flags in CMTP, HIDP & BNEP
- Disallow local privacy & OOB data combo to prevent a potential race
- Expose SMP & ECDH selftest results through debugfs
- Expose current Device ID info through debugfs
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.
ipv6 does not conform with this in three places:
1) ip6_fragment: we do consult ipv6_npinfo for frag_size
2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
loop the packet back to the local socket
3) ip6_skb_dst_mtu could query the settings from the user socket and
force a wrong MTU
Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.
Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to specification etsi 102 622 chapter 4.4 pipes
identifier is 7 bits long giving a 127 possible pipes value.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to etsi 102 622 chapter 11.2.2.4 EVT_TRANSACTION,
the nfc_evt_transaction parameters can be 0 up to 255 byte long.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to specification etsi 102 622 chapter 4.4 pipes identifier
is 7 bits long giving a 127 possible pipes value.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
That way we don't have to reinstantiate another nf_hook_state
on the stack of the nf_reinject() path.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there's a HCI request API available where the callback receives
the resulting skb, we can convert the local OOB data reading to use this
new API. This patch does the necessary update in mgmt.c (which also
requires moving the callback higher up since it's now a static function)
and removes the custom calls from hci_event.c that are no-longer
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_pending() function has no users anymore, so simply remove
it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the synchronous HCI requests use the new API and a new private
variable the recv_evt member of hci_dev is no-longer needed. This patch
removes it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there's an API in place that allows passing the resulting skb
to the request callback we can conveniently convert the hci_req_sync and
related functions to use it. Since we still need to get the skb from the
async callback into the sleeping _sync() function the patch adds another
req_skb variable to hci_dev where the sync request state is tracked.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a second possible callback for HCI requests where the
callback will receive the full skb of the last successfully completed
HCI command. This API is useful for cases where we want to use a request
to read some data and the existing hci_event.c handlers do not store it
e.g. in the hci_dev struct.
The reason the patch is a bit bigger than just adding the new API is
because the hci_req_cmd_complete() functions required some refactoring
to enable it: now hci_req_cmd_complete() is simply used to request the
callback pointers if any, and the actual calling of them happens from a
single place at the end of hci_event_packet(). The reason for this is
that we need to pass the original skb (without any skb_pull, etc
modifications done to it) and it's simplest to keep track of it within
the hci_event_packet() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for element timeouts to nft_hash. The lookup and walking
functions are changed to ignore timed out elements, a periodic garbage
collection task cleans out expired entries.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
GC is expected to happen asynchrously to the netlink interface. In the
netlink path, both insertion and removal of elements consist of two
steps, insertion followed by activation or deactivation followed by
removal, during which the element must not be freed by GC.
The synchronization helpers use an unused bit in the genmask field to
atomically mark an element as "busy", meaning it is either currently
being handled through the netlink API or by GC.
Elements being processed by GC will never survive, netlink will simply
ignore them. Elements being currently processed through netlink will be
skipped by GC and reprocessed during the next run.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helpers for GC batch destruction: since element destruction needs
a RCU grace period for all set implementations, add some helper functions
for asynchronous batch destruction. Elements are collected in a batch
structure, which is asynchronously released using RCU once its full.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add API support for set element timeouts. Elements can have a individual
timeout value specified, overriding the sets' default.
Two new extension types are used for timeouts - the timeout value and
the expiration time. The timeout value only exists if it differs from
the default value.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add set timeout support to the netlink API. Sets with timeout support
enabled can have a default timeout value and garbage collection interval
specified.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Dumazet